Professional Documents
Culture Documents
Datasheet TLP350 PDF
Datasheet TLP350 PDF
TLP350
Industrial Inverter
Inverter for Air Conditioner Unit: mm
IGBT/Power MOSFET Gate Drive
IH (Induction Heating)
Schematic ICC 8
VCC
(Tr1)
IF
2+
VF IO 6
3− (Tr2) VO
5
GND
1 2010-06-17
TLP350
Absolute Maximum Ratings (Ta = 25°C)
Characteristic Symbol Rating Unit
Forward current IF 20 mA
Forward current derating (Ta ≥ 85°C) ΔIF/ΔTa −0.54 mA/°C
LED
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width PW ≤ 1 μs, 300 pps
Note 2: Exponential waveform pulse width PW ≤ 0.3μs, f ≤ 15 kHz
Note 3: Exponential waveform IOPH ≥ -2.0A (≤ 0.3μs), IOPL ≤ 2.0A (≤ 0.3μs)
Note 4: At 2 mm or more from the lead root.
Note 5: This device is regarded as a two terminal device: pins 1, 2, 3 and 4 are shorted together, as are pins 5, 6, 7
and 8.
Note 6: A ceramic capacitor (0.1 μF) should be connected from pin 8 to pin 5 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypass may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Note 7: Input signal rise time (fall time) < 0.5 μs.
Note 8: If the rising slope of the supply voltage (VCC) for the detector is steep, stable operation of the internal circuits
cannot be guaranteed.
Be sure to set 3.0V/μs or less for a rising slope of the VCC.
2 2010-06-17
TLP350
Electrical Characteristics (Ta = −40 to 100°C, unless otherwise specified)
Test
Characteristic Symbol Test Conditions Min Typ.* Max Unit
Circuit
Forward voltage VF ⎯ IF = 10 mA, Ta = 25°C ⎯ 1.6 1.8 V
Temperature coefficient of forward
∆VF/∆Ta ⎯ IF = 10 mA ⎯ −2.0 ⎯ mV/°C
voltage
Input reverse current IR ⎯ VR = 5 V, Ta = 25°C ⎯ ⎯ 10 μA
Input capacitance CT ⎯ V = 0 , f = 1 MHz, Ta = 25°C ⎯ 45 250 pF
VCC = 30 V,IF = 5 mA
⎯ −1.6 -1.0
V8-6 = 3.5 V
“H” Level IOPH 1
VCC = 15 V,IF = 5 mA
⎯ ⎯ -2.0
Output current V8-6 = 7.0 V
A
(Note 9) VCC = 30 V,IF = 0 mA
1.0 1.6 ⎯
V6-5 = 2.5V
“L” Level IOPL 2
VCC = 15 V,IF = 0 mA
2.0 ⎯ ⎯
V6-5 = 7.0V
Note 10: This product is more sensitive to static electricity (ESD) than the conventional product because of its
minimal power consumption design.
General static electricity precautions are necessary for handling this component.
3 2010-06-17
TLP350
Switching Characteristics (Ta = −40 to 100°C, unless otherwise specified)
Test
Characteristic Symbol Test Conditions Min Typ.* Max Unit
Circuit
V V
4 VOH VEE1 VOL VEE1
5 4 5
IF VCC VCC
4 4
5 5
4 2010-06-17
TLP350
Test Circuit 7: tpLH, tpHL, tr, tf, PDD
8
1
0.1 μF
IF Vo IF
Cg =10 nF VCC tr tf VOH
Rg = 20 Ω 90%
VO 50%
4
5 10%
tpLH tpHL
VOL
Test Circuit 8: CMH, CML
8 90% 1000 V
1
IF VCM
0.1 μF
SW 10%
A B VO VCC tr tf
4 SW A: IF = 5 mA
5 CMH
VCM VO 26V
1V
+ − CML
SW B: IF = 0 mA
800(V ) 800(V )
CM = CM =
L t ( μs) H t f ( μs)
r
CML (CMH) is the maximum rate of rise (fall) of the common mode voltage that can be
sustained with the output voltage in the low (high) state.
5 2010-06-17
TLP350
I F ─ VF ⊿ VF/⊿ Ta- IF
100 -2.6
Ta = 25 °C
50
30
C o e f f i c i e n t ⊿ V F / ⊿ Ta ( m V / °C)
-2.4
F o r w a r d C u r r e n t I F (mA)
10
5 -2.2
3
1 -2.0
0.5
0.3
-1.8
0.1
0.05 -1.6
0.03
0.01 -1.4
1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.3 0.5 1 3 5 10 30
F o r w a r d Vo l t a g e VF(V) F o r w a r d C u r r e n t I F (mA)
I F - Ta V C C - Ta
40 40
F o r w a r d C u r r e n t I F (mA)
30 30
Supply Voltage VCC (V)
20 20
10 10
0 0
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
Ambient Temperature Ta(°C) Ambient Temperature Ta(°C)
VOL - Ta VOH - Ta
-30 30
VF = 0.8V IF = 5mA
RL=20Ω RL=20Ω
-25
High Level Output Voltage VOH[V]
25
Low Level Output Voltage VOL[V]
-20 20
VCC1=15V,VEE1=-15V
VCC1=15V,VEE1=-15V
-15 15
-10 VCC1=7.5V,VEE1=-7.5V 10
VCC1=7.5V,VEE1=-7.5V
-5 5
0 0
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
Ambient Temperature Ta(°C) Ambient Temperature Ta(°C)
6 2010-06-17
TLP350
I C C L - Ta I C C H - Ta
5 5
I F=5mA
VCC=30V
level supply current IC C L (mA)
3 3
2 2
1 1
Low
0 0
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
Ambient Temperature Ta(°C) Ambient Temperature Ta(°C)
t p H L , t p L H - Ta tpHL,tpLH-VCC
500 500
IF=5mA,VCC=30V,
(ns)
(ns)
IF=5mA,Rg=20Ω,Cg=10nF
Rg=20Ω,Cg=10nF
400 400
Propagation delay time tPLH, tPHL
100 100
0 0
-40 -20 0 20 40 60 80 100 15 20 25 30
Ambient Temperature Ta(°C) Supply Voltage VCC (V)
tpHL,tpLH-IF IFLH-Ta
500 5
VCC=30V, VCC=15V,VO>1V,
(ns)
Rg=20Ω,Cg=10nF IO=0mA
400 4
Propagation delay time tPLH, tPHL
300 tpLH 3
200 2
tpHL
100 1
0 0
4 6 8 10 12 14 16 -40 -20 0 20 40 60 80 100
Forward current IF (mA) Ambient Temperature Ta(°C)
7 2010-06-17
TLP350
IOPL-Ta IOPH-Ta
5 0
3 -2
IOPL IOPH
MAX MAX
2 -3
V8-6=7.0V
V6-5=2.5V
1 -4
0 -5
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
IOPL-VOL IOPH-VOH
5.0 0.0
IF=0mA,VCC=15V IF=5mA,VCC=15V
(Note:8)
(Note:8)
-1.0
High Level Output Voltage VOH[V]
Ta=100°C
Low Level Output Voltage VOL[V]
4.0
Ta=25°C -2.0
3.0
Ta=-40°C
-3.0
Ta=-40°C
2.0
-4.0 Ta=25°C
1.0 -5.0
Ta=100°C
0.0 -6.0
0 0.5 1 1.5 2 2.5 0 -0.5 -1 -1.5 -2 -2.5
Low Level Output Peak Current IOPL(A) High Level Output Peak Current IOPH(A)
VCC-VO(VUVLO)**
14
IF = 5mA , Vo > 2.5V
12 **Test Circuit : VCC-VO(VUVLO)
UVLOHYS
10 1 8
Output Voltage VO[V]
8
IF
+VUVLO VO
6 VCC
-VUVLO
4
4 5
2
0 5 10 15 20
Supply Voltage VCC (V)
8 2010-06-17
TLP350
9 2010-06-17