Professional Documents
Culture Documents
Husqvarna 340/345/350 Operator's Manual
Husqvarna 340/345/350 Operator's Manual
CRAFTSMAN 359.35274
Operator's manual (CARB, EPA)
101 90 07-95
KEY TO SYMBOLS
Symbols
Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective glasses or visor Regular cleaning is required.
2- English
CONTENTS
Before using a new saw Contents
• Read the instructions carefully.
• Check cutting equipment is correctly fitted and adjusted.
See page 25. Key to symbols ...............................................................
2
• Refuel and start the saw. Check the carburetor settings.
See pages 26-29. Safety instructions
• Do not use the saw until sufficient chain oil has reached the Personal protective equipment ............................................ 4
chain, see page 14. Chain saw safety equipment ................................................ 4
IMPORTANT! If the carburetor mixture is too lean it greatly Inspecting, maintaining and servicing chain saw safety
increases the risk of engine failure. equipment ............................................................................ 8
Poor maintenance of the air filter will cause carbon build-up on Cutting equipment ................................................................ 10
the spark plug and lead to difficult starting. How to avoid kickback ......................................................... 16
If the chain is badly adjusted it will cause increased wear or General safety precautions ................................................ 18
damage to the bar, drive sprocket and chain.
General working instructions .............................................. 19
Maintenance, replacement, or repair of the emission
control devices and systems may be performed by any What is what?
nonroad engine repair establishment or individual. What is what? .................................................................... 24
Assembly
WARNING! Mounting guide bar and chain ........................................... 25
Under no circumstances may the design of Fuel handling
the machine be modified without the permis-
Fuelmix .............................................................................. 26
sion of the manufacturer. Always use genuine
spare parts/accessories. Non-authorized Fuelling .............................................................................. 27
modifications and/or accessories can result
Start and stop
in serious personal injury or the death of the
Start and stop .................................................................... 28
operator or others.
Maintenance
Your warranty does not cover damage or
Carburetor ......................................................................... 29
liability caused by the use of non-authorized
accessories or replacement parts. Starter device .................................................................... 30
Air filter .............................................................................. 31
Spark plug ......................................................................... 31
A chain saw is a dangerous tool if used Muffler ................................................................................ 31
carelessly or incorrectly and can cause
Needle bearing maintenance ............................................ 31
serious, even fatal injuries. It is very important
that you read and understand these Adjustment of the oil pump (350) ...................................... 31
instructions. Cooling system .................................................................. 32
Centrifugal cleaning "Air Injection". ................................... 32
Winter use ......................................................................... 32
You will find the following labels
on your chain saw: Daily maintenance ............................................................. 33
Weekly maintenance ......................................................... 33
Monthly maintenance ........................................................ 33
Technical data
Thissawiscapableofseverekickback./_--------_, 340 .................................................................................... 34
Followall safetyprecautions
in theOperator°s Manual(s) W 345 ....................................................................................
350 ....................................................................................
34
34
Failureto followinstructionscouldresulfinserious
personalinjury.Recommended cultingequipment Federal and California Emission Control
Oregon95 VPChainand15"to18"barwith max.
10teethbarnosesprocket.Otherlowor reduced Warranty Statement
kickbackcombinations in Operator's
Manual(s).
Your warranty rights and obligations ................................. 35
NATIONAL STANDARD SAFETY SPECIFICATIONS FOR
(_ LISTED 54L1. LISTED IN ACCORDANCEWITH AMERICAN
GASOLINE POWERED CHAIN SAWS (ANSI B175.1-1991) y
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Model 340
f
IMPORTANTENGINEINFORMATION/
_ Husq_rna ....
HUSQVARNA AB HUSKVARNA SWEDEN EM
THIS ENGINE CONFORMSTO U.S. EPA PH 1
EMISSION REGULATION FOR SMALL
NONROAD ENGINES. REFER TO OPERATOR'S
MANUAL FORMAINTENANCE
SPECIFICATIONSAND ADJUSTMENTS.
• PROTECTIVE HELMET
• HEARING PROTECTION • Chain brake and front hand
• PROTECTIVE GLASSES guard
OR VISOR
• Throttle lock
• Chain catcher
• PROTECTIVE TROUSERS
WITH SAW PROTECTION
• Right hand guard
SOLE
4- English
SAFETY INSTRUCTIONS
3 You can also use the
1 Chain brake and front hand guard
chain brake as a
YOUR chain saw is equipped with a chain brake that is desig-
temporary brake when you
ned to stop the chain immediately if you get a kickback.
change position or if you
The chain brake reduces the risk of accidents, but only You can
put the saw down for a
prevent them.
short time. You should
also apply the chain brake
Take care when using your _ __
saw and make sure the manually if there is a risk
kickback zone of the bar of the chain accidentally
hitting anyone or anything
close by.
never touches any object. _ ;
English - 5
SAFETY INSTRUCTIONS
6 The way the chain brake is triggered, either manually or 2 Throttle lock
automatically, depends on the force of the kickback and the The throttle lock is designed
position of the chain saw in relation to the object that the to prevent accidental opera-
kickback zone of the bar strikes. tion of the throttle control.
When you press the lock (A)
(i.e. when you grasp the
If you get a violent handle) it releases the throttle A
kickback while the
trigger (B).
kickback zone of the bar
When you release the handle
is farthest away from you the throttle trigger and the
the chain brake will be throttle lock both move back
activated by the to their original positions. This
movement of the
movement is controlled by two
counterweight (INERTIA independent return springs.
ACTIVATED). This arrangement means that B
the throttle control is
automatically locked at the
idle setting when you release
the handle.
3 Chain catcher
The chain catcher is designed
If the kickback is less
to catch the chain if it snaps or
violent or the kickback
zone of the bar is closer jumps off. This should not
happen if the chain is properly
to you the chain brake will
tensioned (see section on
be activated manually by
"Assembly') and if the bar and
the movement of your left
chain are properly serviced
hand.
and maintained.
(See section on "General
workinginstructions').
6- English
SAFETY INSTRUCTIONS
5 Vibration damping system 6 Stop switch
Your chain saw is equipped Use the stop switch to switch
with a vibration damping off the engine.
\
system that is designed to
minimise vibrations and make \ j
operation easier. /
The vibration damping system The exhaust fumes from the engine are hot
reduces the vibrations and may contain sparks which can start a fire.
transmitted from the engine Never start the saw indoors or near
and chain to the handles of combustible material!
the chain saw. The body of
the saw, including the cutting
equipment, is insulated from In areas with a hot, dry
the handles by vibration climate there is a high risk of
damping units. forest fires. These areas are
sometimes controlled by
legislation and requirements
that among other things the
muffler must be equipped with
Overexposure to vibration can lead to an approved type of spark
circulatory damage or nerve damage in people arrestor mesh.
who have impaired circulation.
Contact your doctor if you experience For mufflers it is very
symptoms of overexposure to vibration. important that you follow the
These symptoms include numbness, loss of instructions on checking,
feeling, tingling, pricking, pain, loss of maintaining and servicing your
strength, changes in skin colour or condition. saw (see the section on
These symptoms normally appear in the "Inspecting, maintaining and
fingers, hands or wrists. servicing chain saw safety
equipment').
so
Thefor a shortgets
time afterwards.
hot in useDO NOT
muffler very and remains
TOUCH THE MUFFLER IF IT IS HOT!
English - 7
SAFETY INSTRUCTIONS
Inspecting, maintaining and servicing Checking the inertia brake release
8 - English
SAFETY INSTRUCTIONS
2 Throttle lock 4 Right hand guard
English - 9
SAFETY INSTRUCTIONS
Muffler CUTTING EQUIPMENT
Never use a chain saw This section describes how to choose and maintain your cutting
that has a faulty muffler. equipment in order to:
• Reduce the risk of kickback.
• Reduce the risk of the chain breaking or jumping.
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
© ©
10- English
SAFETY INSTRUCTIONS
1 Cutting equipment designed to minimise C Some terms that describe the bar and chain
kickback When the cutting equipment supplied with your saw becomes
worn or damaged you will need to replace it. Use only the type
of bar and chain recommended by us. See the "Technical data"
section to find out which equipment is recommended for your
saw.
Bar
The only way to avoid kickback is to make sure that the kick-
, LENGTH (inches/cm)
back zone of the bar never touches anything.
By using cutting equipment with "built-in" kickback protection NUMBER OF TEETH ON
and keeping the chain sharp and well-maintained you can
reduce the effects of kickback. BAR TIP SPROCKET (T).
Small number = small tip
radius = low-kickback
A Bar
The smaller the tip radius the CHAIN PITCH (inches)
smaller the kickback zone and
The spacing between the
the lower the chance of drive links of the chain must
kickback.
match the spacing of the
teeth on the bar tip sprocket
and drive sprocket.
Combining these links in different ways gives different degrees Saw chain
of kickback reduction. In terms of kickback reduction alone, four
SAW CHAIN PITCH
different types of link are available.
(inches)
Spacing between drive
Kickback reduction links.
Cutting link Drive link Side link
English- 1 1
SAFETY INSTRUCTIONS
2 Sharpening your chain and adjusting It is very difficult to sharpen a
chain correctly without the
raker clearance right equipment. We
recommend you use a file
gauge. This will help you
obtain the maximum kickback
reduction and cutting
performance from your chain.
A General information on sharpening cutting teeth
, Never use a blunt chain. When the chain is blunt you have to
exert more pressure to force the bar through the wood and
the cuttings will be very small. If the chain is very blunt it will
not produce any cuttings at all, just wood powder.
i i_ ¸ i i i i i i i ............ i ...... i i i i
FILE POSITION
12 - English
SAFETY INSTRUCTIONS
C General advice on setting raker clearance D Setting the raker clearance
, On a low-kickback cutting
link the front edge of the
raker lip is rounded. It is
very important that you O , Place the gauge over the
raker lip.
maintain this radius or bevel
when you adjust the raker
clearance.
Place the file over the part
, We recommend the use of a of the lip that protrudes
raker gauge to achieve the through the gauge and file
correct clearance and bevel off the excess. The
on the taker lip. clearance is correct when
you no longer feel any
resistance as you draw the
file over the gauge.
English - 13
SAFETY INSTRUCTIONS
4 Lubricating cutting equipment
14 - English
SAFETY INSTRUCTIONS
C Checking chain lubrication E Needle bearing maintenance
If the chain lubrication is not working: NOTE! Use only high quality bearing grease.
English - 15
SAFETY INSTRUCTIONS
H Bar HOW TO AVOID KICKBACK
Check regularly:
16 - English
SAFETY INSTRUCTIONS
General rules 6 Take great care when you
cut with the top edge of
1 If you understand what kickback is and how it happens then
the bar, i.e. when cutting
you can reduce or eliminate the element of surprise. By
from the underside of the
being prepared you reduce the risk. Kickback is usually
object. This is known as
quite mild, but it can sometimes be very sudden and
violent. cutting on the push
stroke. The chain tries to
push the saw back
Always hold the saw towards the user.
firmly with your right hand
Unless the user resists
on the rear handle and
your left hand on the front this pushing force there is
a risk that the saw will
handle.
move so far backwards
Wrap your fingers and that only the kickback
thumb around the hand- zone of the bar is in
les. You should use this contact with the tree. This
will cause kickback.
grip whether you are
right-handed or left-
Cutting with the bottom
handed. This grip
minimises the effect of edge of the bar, i.e. from
the top of the object
kickback and lets you
downwards, is known as
keep the saw under
control. cutting on the pull stroke.
English - 17
SAFETY INSTRUCTIONS
7 FUEL SAFETY
GENERAL SAFETY PRECAUTIONS
(Refuelling, fuel mixture, storage.)
1 Chain saws are designed solely for cutting wood. The only
cutting equipment that can be used with this chain saw are
the combinations of bars and chains recommended in the
'Technical data" section.
J
Never use a chain saw that has been modified in any way from the refuelling point
from its original specification. before starting it.
, Place the saw on the Never use any accessories other than those recommended
ground and hold the rear in this manual. See the sections on "Cutting equipment"
handle down with your right and 'Technical data"
foot. Grasp the front handle
firmly using your left hand.
Make sure the chain saw is
steady and the chain is not
touching the ground. Then
grasp the starter handle
with your right hand and pull
the starter cord.
18 - English
SAFETY INSTRUCTIONS
4 Check the area around
GENERAL WORKING INSTRUCTIONS
you for possible obstacles
such as roots, rocks,
branches, ditches, etc., in
case you have to move
suddenly. Take great care
when working on sloping
ground.
Important
1 Before using a chain saw you must understand the effects of
kickback and what causes it, (See the section on "How to
avoid kickback".)
2 Before using a saw you must understand the difference Take the utmost care
between sawing with the top and bottom edges of the bar, when cutting through
(See the section on "How to avoid kickback".) branches or logs that are
in tension. A log or branch
that is in tension can
1 Basic safety rules suddenly spring back into
1 Look around you: its natural position before
or after you cut it. If you
o to make sure there are no stand on the wrong side
people, animals or other or start cutting in the
objects nearby that might wrong place it may strike
affect your work. you or your chain saw.
This could make you lose
o to make sure that none of control and cause a
the above might come within serious accident.
reach of your saw or be
injured by falling trees.
English - 19
SAFETY INSTRUCTIONS
2 Basic cutting technique Two factors decide whether the chain will jam or the log will
split. The first is how the log is supported and the second is
General
whether it is in tension.
. Always use full throttle when cutting!
In most cases you can avoid these problems by cutting in two
. Reduce the speed to idle after every cut (running the stages; from the top and from the bottom of the log. You need
engine for too long at full throttle without any load can lead to to support the log so that it will not trap the chain or split during
serious engine damage). cutting.
Terms:
Cutting = General term for cutting through wood. The following instructions describe how to handle most types of
Limbing = Cutting limbs off a felled tree,
situation that you will be faced with when using a chain saw.
Splitting = When the object you are cutting breaks off
before the cut is complete.
Cutting
1 The log is lying on the
ground. There is little risk
of the chain jamming or
There are five important factors you should consider the log splitting, However
before making a cut: there is a risk that the
chain will touch the
ground when you finish
the cut.
1 Make sure the bar will not
jam in the cut.
A If it is possible to turn
Make sure the chain will the log you should stop
not strike the ground or cutting about 2/3 of the
any other object during or way through.
after cutting.
20- English
SAFETY INSTRUCTIONS
2 The log is supported at one Tree felling technique
end. There is a high risk
that it will split.
A Safe distance
A Start by cutting from The safe distance between a tree that is to be felled and
below (about 1/3 of the anyone else working nearby is at least 21/2 tree lengths.
way through). Make sure that no-one else is in this "risk zone" before or during
felling.
Bend
Limbing
Wind direction
When limbing thick branches
you should use the same
1 2
Arrangement of branches
approach as for cutting.
Cut difficult branches piece by
Weight of snow
piece.
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to make it
fall in the direction you first intended.
Another very important factor, which does not affect the felling
direction but does affect your safety, is to make sure the tree
has no damaged or dead branches that might break off and hit
you during felling.
English - 21
SAFETY INSTRUCTIONS
C Clearing the trunk and preparing your retreat FELLING CUT
The felling cut is made from the opposite side of the tree and it
Remove any branches that must be perfectly horizontal. Stand on the left side of the tree
are in the way. To do this it is and cut with the bottom edge of the bar.
best to work from the top
down and keep the trunk Make the FELLING CUT
between you and the chain about 3-5 cm (1.5-2 inches)
saw. Never limb above above the flat section of the
shoulder height. DIRECTIONAL CUT.
The directional cut should run When the felling cut and
1/4 of the diameter through directional cut are complete
the trunk and the angle the tree should start to fall
between the TOP CUT and under its own weight or with
BOTTOM CUT should be 45 °. the aid of a FELLING WEDGE
or BREAKING BAR.
22- English
SAFETY INSTRUCTIONS
We recommend that you use 4 Freeing a tree that has fallen badly = high
a bar that is longer than the
accident risk
diameter of the tree, so that
you can make the FELLING
CUT and DIRECTIONAL CUT
with single cutting stokes. A Freeing a"Trapped tree"
(See "Technical data" to find The safest method is to use a winch.
out which lengths of bar are A Tractor-mounted B Portable
recommended for your saw).
\
•._ ) :
a) Work out which way the tree or branch will move if released
and where the natural "BREAKING POINT" is (i.e. the place
it would break if it was bent even more).
E Limbing
Make sure there are no b) Decide which is the SAFEST way to release the tension
obstacles in your way. Work and whether YOU are able to do it safely. In complicated
on the left side of the trunk. situations the only safe method is to put aside your chain
Work close to the saw for saw and use a winch.
maximum control. If possible,
General advice:
let the weight of the saw rest
on the trunk.
a) Position yourself so that
you will be clear of the
tree or branch when it
Keep the tree between you
springs free.
and the saw as you move
along the trunk.
English - 23
WHAT IS WHAT?
What is what?
1. Cylinder cover. 15. Saw bar.
3. Front hand guard. 17. Chain catcher. Catches chain if it jumps or breaks.
5. Chain oil tank. 19. Right hand guard. Protects right hand if chain breaks or
jumps.
6. Starter handle.
20. Throttle control.
7. Adjuster screw, carburetor.
21. Throttle lock. Prevents accidental operation of throttle
8. Choke control/Start throttle lock. control.
34,,
English - 25
FUEL HANDLING
Fuelmix Mixing
, Always mix the gasoline
IMPORTANT! The chain saw is equipped with a two-stroke and oil in a clean container
engine and must always been run using a mixture of gasoline intended for fuel.
and two-stroke engine oil. It is important to accurately measure
the amount of oil to be mixed to ensure that the correct mixture Always start by filling half
is obtained. When mixing small amounts of fuel, even small the amount of the gasoline
inaccuracies can drastically affect the ratio of the mixture. to be used. Then add the
entire amount of oil. Mix
(shake) the fuel mixture.
Add the remaining amount
of gasoline.
Two-stroke oil
, For the best results use HUSQVARNA two-stroke oil, which is
especially developed for chain saws. Mixing ratio 1:50 (2%).
, Never use two-stroke oil intended for water cooled outboard Chain oil
engines, so-called, outboard oil. , The chain lubrication
system is automatic. Always
, Never use oil intended for four-stroke engines. use special chain oil with
good adhesive
characteristics.
In countries where no
special chain oil is available,
EP 90 transmission oil can
be used.
Gasoline Oil
2%(1:50) Never use waste oil. This
Lit. Lit. results in damage to the oil
5 0,10 pump, the bar and the
chain.
10 0,20
15 0,30 , It is important to use oil of
20 0,40 the right viscosity according
US US to the air temperature.
gallon fl. oz.
1 In temperatures below 0°C
2 1/2
(32°F) some oils become
2 1/2 6 1/2 too viscous. This can
5 12 7/8 overload the oil pump and
result in damage to the oil
pump components.
26- English
FUEL HANDLING
Fuelling
Min 3 m
(loft)
J
English - 27
START AND STOP
Start and stop Start
Grip the front handle with your
left hand and hold the saw
down by putting your right foot
in the rear handle. Pull the
starter handle with your right
hand and pull out the starter
cord slowly until the starter
pawls engage. Then pull
sharply.
FAST IDLE:
Combined choke/fast idle is
received when the choke is
Stop
The engine is stopped by
moved to choke position.
switching off the ignition.
\\
\ j
Warm engine /
Use the same procedure as
for starting cold engine but
without choke. Fast idle is
recived by first set the choke
control in choke position, and
then back again.
28- English
MAINTENANCE
Carburetor Conditions
Your Husqvarna product has been designed and manufactured , Before any adjustments are made the air filter should be
to specifications that reduce harmful emissions. clean and the cylinder cowling fitted. Adjusting the carburetor
After your unit has been run 8-10 tanks of fuel the engine has while a dirty air filter is in use will result in a leaner mixture
broken in. To ensure that your unit is at peak performance and when the filter is finally cleaned. This can give rise to serious
producing the least amount of harmful emissions after break in, engine damage.
have your authorized servicing dealer, who has a revolution , Carefully turn the L and H needle to the mid point.
counter at his disposal, to adjust your carburetor for optimum , Do not attempt to adjust the needles beyond the stops as
operating conditions. damage can occur.
, Now start the saw according to the starting instructions and
run it warm for 10 minutes.
Functioning, Basic setting, Final setting NOTE! If the chain rotates the T screw should be turned
counter-clockwise until the chain stops.
, Place the saw on a fiat surface so that the bar points away
from you and so that the bar and chain do not come into
contact with the surface or other objects.
English - 29
MAINTENANCE
Starter device Tensioning the recoil spring
30- English
MAINTENANCE
Air filter Muffler
The air filter must be regularly cleaned from dust and dirt in
order to avoid:
o Carburetor malfunctions
o Starting problems
The muffler is designed in
o Engine power reduction order to reduce the noise level
o Unnecessary wear on and to direct the exhaust
the engine parts
gases away from the operator.
o Abnormal fuel consumption The exhaust gases are hot
and can contain sparks, which
may cause fire if directed
against dry and combustible
Clean the air filter daily or material. Some mufflers are
more often if the air is
equipped with a special
exceptionally dusty in the screen.
working area.
If your saw has this type of muffler, you should clean the screen
o Disassemble the air filter by at least once a week. This is done with a wire brush.
removing the cylinder cover
and unscrew the filter. CAUTION! The screen must be replaced, if damaged. The saw
will be overheated, if the screen is clogged. This results in
When reassembling, make
damage on the cylinder and the piston. Never use a saw with a
sure that the filter is tight
against the filter holder. clogged or defective muffler.
Clean the filter by brushing
or shaking it.
o A more thorough cleaning of Needle bearing maintenance
the filter is obtained by
washing it in water and
soap.
A
An air filter, which is used for The clutch drum is equipped
some time, cannot be cleaned
completely. Therefore it must
with one of the following chain &&
sprockets:
be replaced by a new one,
with regular intervals.
IMPORTANT! A damaged air
filter must always be
o Spur sprocket (A) (the chain
sprocket is welded on the
drum)
®J
replaced. o Rim sprocket (B)
A Husqvarna chain saw can be equipped with different types of (exchangeable)
airfilter according to working and weather conditions, season etc. Both versions have built-in
needle bearing at the drive
shaft, whitch has to be
Spark plug greased regularly (once a
week).
NOTE! Use only high
quality bearing grease.
The spark plug condition is influenced by:
. An incorrect carburetor setting.
. Wrong fuel mixture (too much oil in the gasoline).
. A dirty air filter. Adjustment of the oil pump (350)
These factors cause deposits on the spark plug electrodes,
which may result in malfunction and starting difficulties.
English - 31
MAINTENANCE
Cooling system Winter use
During winter time, powder snow and cold weather can cause
running problems, such as:
IMPORTANT! In order to
keep the function of the
centrifugal cleaning, a
continous maintenance and
care must be made.
32- English
MAINTENANCE
Below you will find some general maintenance instructions. Weekly maintenance
If you have more questions, contact your servicing dealer.
[]
English - 33
TECHNICAL DATA
340 345 350
Engine
Cylinder volume, cu.in/cm 3 2,5/40,8 2,7/45,0 3,0/49,4
Cylinder bore, inch/mm 1,57/40,0 1,65/42,0 1,73/44
Stroke, inch/mm 1,28/32,5 1,28/32,5 1,28/32,5
Idle speed, rpm 2 700 2 700 2 700
Power, kW/rpm 2,0/9 000 2,2/9 000 2,3/9 000
Ignition system
Manufacture FHP FHP FHP
Type of ignition system CD CD CD
Spark plug NGK BPMR 7A NGK BPMR 7A NGK BPMR 7A
Champion RCJ 7Y Champion RCJ 7Y Champion RCJ 7Y
Electrode gap, inch/mm 0,020/0,5 0,020/0,5 0,020/0,5
Weight
Without bar and chain, Lbs/kg 10,4/4,7 10,4/4,7 10,6/4,8
Chainlbar
Standard bar length,
inches/cm 13"/33 13"/33 13"/33
Recommended bar lengths,
inches/cm 13-20"/33-50 13-20"/33-50 13-20"/33-50
Usable cutting length,
incheslcm 12-19"/31-49 12-19"/31-49 12-19"/31-49
English - 35
usqvarna SERVICE 5
Ersatzteile Ersetzt
Repuestos Reemplaza
106 25 18-63
DIV 71 SOURCE 359
503 89 30-02
. _ ;,o_8_,__o,.IT1
__ _ / p5371080_01.1
ii
_Husqvarna
*503 89 64-01 _
""
-
"503 85 66-01 _[_ I__ _ _ 503 21 70-10" (x4) _J -
503 21 70-10"
89 16-01"
503 21 74-12
537 02 71-01"
721 11 64-30*
503 93 21-01
537 15 48-01
503 24 09-05
340, 345
503 87 30-72
(.325x7 SPUR) 503 25
*503 20 34-25
C *compl 503 91 05-01
*503
D 00-73 (345)
*compl 503 87 02-74 (340) *compl 503 86 99-71 (350)
O
503 97 13-01
503 97 13-01
_503 92 60-02
L3 86
25_0! (345 x2)
89 44-01
[503861_c25_0
_
503
_750oO328 90-03 (340)
374410-00 (x2)_ _0 _
mpl 503 87 01-71" (340)
mpl 503 90 73-71" (345)
45 16-01"
*503 93 23-02
*503 93 23-0
DIV 71 SOURCE 359
29-87 (x2)
*compl 503 87 96-01 (FG) 340, 345 *compl 503 86 28-02 (DF) 340, 345, 350
*724 12 87-59
r_
*503 86 36-01
G
537 02 40-02
40-01 NYLON 44p
80p
537 02 40-03 FELT
503 86 94-01
503 88 92_
503 21 74-50 (x2)
537 02
503 89 60-01
503 86 96-0
503 86 95-01
503 86 97-01 _
503 86 63-01
503 86 64-01
503 86 62-01
DIV 71 SOURCE 359
503 88 59-01
(350)_
503 88 72-01
57-01
*537 04 03-01
86-01
**compl 537 07 12-01
(345, 350)
503 21 74-12
_503 86
03 57 89-01
compl 503 90 39-01 503 87 55-01"
01 62 68-01
503 21 70-10"
04-01 *
62 98-01"
503 57 76-02
21 88-25
503 44 32-01
503 21 88-25
85 41-01
503 89 83-01__
_ 503 89 87-01
04-01
503 96 24-06
06-01
*503 54 39-01
*/*'501 63 06-01_
*503 21 77-16
503 21 73-21 (X4)_
/
537 09 31-01"
*503 21 29-10
N *compl 503
**compl 503 28
28 18-03
16-14 Walbro
Walbro HDA
HDA 154 C (EPA)
159 A
503 17 63-01"
*503 10 87-01 (x4)
501 66 73-01" (_
505 31 67-17"
505 52 01-25"
501 66 83-01"
*503 66 96-01
*530 03 50-15
*503 97 06-01
"501 83 29-01 503 57 42-01"
501 46 87-01" _
"501 66 62-01
P Tillbeh6r
Accessories 501 69 17-01
Zubeh6re
Accessoires
Accesorios
503 91 06-71
Winter kit
*compl 537 04 28-71
"501 63 97-01_
70-16"
DIV 71 SOURCE 359
Up to 991499999
503 89 07-02
Up to 010604200 (340)
Up to 010602850 (345)
Up to 010702450 (350)
*503 87
*503 85 99-01-
l| Up to 000601101 (345)