8 7 6 5 4 3 2 1

REVISION HISTORY
TABULATION BLOCK REV DESCRIPTION DATE DRAFTED DRAFTER
.880
PART NUMBER DESCRIPTION AE SEE IGNITE 2019/NOV/26 A.CRUZ
7 .078 .003
172922001 OBSOLETE GENERAL NOTES: UNLESS OTHERWISE SPECIFIED
2X
R.53 1. MATL: POLYCARBONATE (EDWARDS P/N 470267001).
172922002 OBSOLETE
2. REGRIND: NONE
172922003 TWO CAVITY TOOL
3. DRAFT: 1 $ PER SIDE MAX, STRAIGHT & RADIAL.
172922004 FOUR CAVITY TOOL +INDICATES DIMENSION PLUS DRAFT,
D .320 .260 P/L .410 .470 172922005 FOUR CAVITY TOOL (21,22,23,24) 4.
-INDICATES DIMENSION MINUS DRAFT
NOTE OBSOLETE.

1.70
5. .005 MAX ALLOWABLE FLASH, EJECTOR
PIN MARKS, AND GATE REMNANT.

R.060 6. NO MOLD RELEASE AGENT ALLOWED.

4X THIS FEATURE HAS SAME 2 7 THESE INSIDE AND OUTSIDE SURFACES

WIDTH AND TAPER AS SEE DETAIL B +.004 .125
TO BE SPI/SPE 2 OR BETTER.
.774
WING ON OPPOSITE SIDE (2-A7) -.003 + FROM
8. CLEANLINESS: REFER TO EDWARDS ELS403 AND
TAPPI CHART. .100 SQ. MM. MAX FOR VISIBLE
3 BUMPS AT 120 $ +/-5 DEG, LOCATED 4 P/L PARTICLES EMBEDDED IN OR ON THE SURFACE.
AS SHOWN ON .32 +.01/-.02 DIA R.020 ALL ARND 9 THIS ZONE OF PLASTIC MUST MEET EDWARDS STRESS
TOP, BOTH WINGS +.006 TEST WITHOUT CRACKING PER ELS574 (USING A MIXTURE
.816 RATIO OF 10 PARTS N-PROPANOL TO 1 PART TOLUENE).
-.004
10. IMPRINTING TO BE WITH TRANS TECH TYPE B NT WHITE
INK AND TYPE BH HARDENER. NUMBERS AND LETTERS
+.005 STYLE : HELVETICA. FOR DASH -003: NUMBERS TO BE
.190 2X .160 .190 0.12 HIGH AND LETTERS 0.09 HIGH. LONG LINES TO BE
-.000 0.24 LONG X 0.020 +.006/-.003 THICK AND SHORT LINE
TO BE 0.12 LONG X 0.012 +/- .002 THICK. FOR
DASH -004: NUMBERS TO BE 0.12 HIGH AND LETTERS
0.10 HIGH. LONG LINES TO BE 0.24 LONG X 0.020 +.006/-.003
THICK AND SHORT LINE TO BE 0.12 LONG X 0.012 + .006
R .04, / -.002 THICK. FOR ALL DASHES LINES TO BE CENTERED
WITHIN .05 ACROSS PARTING LINE. VERTICAL DIMENSIONS
.060 BOTTOM 3 EDGES, TAKEN TO CENTER OF LINE THICKNESS.
BOTH WINGS 11. PARTS TO BE PACKAGED IN DOUBLE POLY BAGS.
INNER BAG TO BE LABELED WITH LOT NUMBER AND QTY.
.180 .003 FAR WALL
C 12. NOTE OBSOLETE.

.210 .003 NEAR WALL

13. NOTE OBSOLETE.

2.980
1 (2.723 )
(3.050 )

R.020 ALL ARND

JUNCTIONS OF BRIDGE
AND P0RTS
7

R.010 9
7 R.030 .131 .002
3X .133 .002

B
+.002 R.005 .003
.011
-.001
.070 R.005 .003
.050 3X
3X

9
R.005 # .003
.30 .070
R.09 +.005
.460 7 .485
-.002
.150 NEARSIDE R.018 .240
ONLY +.002 R.08 .110
3 .740
-.005
R.247
.075 NEARSIDE
R.030 ALL ARND R.04 + .178 .002
ONLY
BASE OF 2 PORTS .310 .070
8 + .137 .002 .148 .002
R.010
.200
.250 R.197 .002 SCALE 2.000 SCALE 2.000
2X .34
CAVITY ID SURFACE,
1 OR 2 DOTS,
FOR -004 CAVITY ID TO BE: SECTION B-B
11,12,13 AND 14
A
- - 2-B4 6
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION OF EDWARDS LIFESCIENCES, THIRD ANGLE PROJECTION
LLC. IT MUST NOT BE REPRODUCED, DISCLOSED, OR USED
- - 2-C4 5 AS THE BASIS FOR THE MANUFACTURE OR SALE OF ANY

SEE DETAIL A
ITEM OTHER THAN THAT FOR WHICH IT WAS PROVIDED

172922003, 172922004 AND 172922005: BODY, VAMP PLUS

WITHOUT PRIOR WRITTEN PERMISSION OF EDWARDS
- - 1-D5 4 LIFESCIENCES, LLC. ALL RIGHTS RESERVED BY EDWARDS
LIFESCIENCES, COPYRIGHT (C) DRAWN BY DESCRIPTION

(2-B7)
1-B3 9 1-A6 3 TOLERANCES UNLESS OTHERWISE SPECIFIED
.185 1-A4 8 1-D3 2
ALL DIMENSIONS IN INCHES
DECIMALS
DJE BODY, VAMP PLUS
.030 1-D8 7 1-C5 1 .X FRACTION DRAWN DATE SIZE DRAWING NO. REV.

D 172922 AE
ZONE NO. ZONE NO. .XX ANGULAR DIMS
.200 .XXX
09/96
INSPECTION INSPECTION
DIMENSIONS DIMENSIONS DO NOT SCALE DRAWING SOURCE FILE CREO SCALE: 3.000 AND NOTED SHEET 1 OF 2
1272 REV F
CAD FORMAT: EDWARDS_D.FRM WC REV: C
Windchill Info: 172922.DRW,AE.1,COMPLETE THIS FORM IS GOVERNED BY DOC-0087869 DRAWING STANDARDS
 8 7 6 5 4 3 2 1

D
3 LOCATING RIBS, .035 HIGH
FROM BOTTOM OF CAVITY,
ORIENTED AS SHOWN

APPROX. GATE LOCATION

DASH -004

+.000
.003
-.001
C 3X @ 120 $ # 5 $

1.236 .015

.012 .002
3X
5
.182 .002
ACROSS TIPS OF 12
CRUSH RIBS

10

FULL R, 3X 8 .142
.006 .001
DETAIL A 3X @ 120 $ # 5 $
SCALE 25.000
6
1.562 .010
6
B 4

4 $
2
.754 .003 CC
2

.257 .010

.137 .010

P/L

DETAIL B IMPRINTING VIEW 10

SCALE 6.000
A

DESCRIPTION

BODY, VAMP PLUS

SIZE DRAWING NO. REV.

D 172922 AE
SCALE: 3.000 AND NOTED SHEET 2 OF 2
1272 REV F
CAD FORMAT: EDWARDS_D.FRM WC REV: C
Windchill Info: 172922.DRW,AE.1,COMPLETE THIS FORM IS GOVERNED BY DOC-0087869 DRAWING STANDARDS