Professional Documents
Culture Documents
298718057-1300EDI-WIRING-DIAGRAMS-for-Genset-Applications 2020 PDF
298718057-1300EDI-WIRING-DIAGRAMS-for-Genset-Applications 2020 PDF
@Perkins
Notes:
On start up for genset applications the ECM automatically determines which speed/load
signal ‘out of range’ (o.o.r.) fault management to use. This is dependant on the wiring
configuration it observes
Stand alone (isochronous) operation – APS & RPS inputs are both inactive.
Manual synchronised load sharing – APS input is active, RPS input is inactive.
Automatic synchronised load sharing – APS input is inactive, RPS input is active.
2 way protection is achieved by selecting 3 way protection and ‘normally open (plastic
tank)’ for the CLS type. No connection should then be made to the CLS input.
Page 8
Perkins Gen Set Power, TPD 1440E, issue 2
18 AWG
41 HSO (+) Feed
See note 4 See note 2 14 AWG
+ 23 HSO Ground feed
14 AWG
42 DPS O/P’s Ground feed
Battery 14 AWG
1 DC/DC Converter
- 10 AWG 14 AWG
2 Ground feed
Notes
1) Wire sizing:
10AWG (approx. 5mm 2 ) Main feed and return to battery
14AWG (approx. 2mm 2 ) ECM pin Nos 21.22.41.23.42.1.2
16AWG (approx. 1mm 2 ) Ignition and diagnostic socket supply
18AWG (approx. 0.8mm 2 ) All other circuits
16 AWG
18 Red
2) Main Power Relay 10 AMP AWG lamp
12V part no. 1688314C1 18 AWG
54 Oil water lamp output
(12V alternative part no’s. 2848A203)
Amber See note 6
24V part no. 2848A226 lamp 18 AWG
55 ENG Warn light output
0
3) Where shown, cables must be twisted together (360 per 25 mm and
screened to minimise noise effects. Connect screen at one end only. Diagnostic
4) connector
All fuses must comply with SAE J1284 and be located close to the CEBA
battery so as to protect the wiring. 10 AMP 16 AWG
5) Clear wire 18 AWG
All unused interface harness cables must be insulated. 16 ATA (+)
16 AWG Black wire 18 AWG (Data link J1708)
17 ATA (-)
6) Recommended rating for lamps is between 2 and 2.2 watts.
See note 3
W1361/1
6
95
96
switch
18 AWG 18 AWG
2) Main Power Relay 34 STI Switch
12V part no. 1688314C1 16 AWG
(12V alternative part no’s. 2848A203) 18
10 AMP Red lamp
AWG 18 AWG
24V part no. 2848A226 54 Oil water lamp output
0 See note 6
3) Where shown, cables must be twisted together (360 per 25 mm and Amber lamp
screened to minimise noise effects. Connect screen at one end only. 18 AWG
55 ENG Warn light output
4)
All fuses must comply with SAE J1284 and be located close to the Diagnostic
battery so as to protect the wiring.
See note 3
Perkins Gen Set Power, TPD 1440E, issue 2
5 AMP
RPS input (PIN 30) is active See note 4 See note 2 14 AWG
23 HSO Ground feed
14 AWG
+ 42 DPS O/P’s Ground feed
14 AWG
Battery 1 DC/DC Converter
10 AWG 14 AWG
2 Ground feed
- 18 AWG
On/off switch 37 RPRE Input
Attention 5 AMP
16 AWG 18 AWG
1 12V or 24V 24 VIGN - IPR (+) Feed
Note: Power supply for ECM must
be taken directly from the battery, + Auto speed
not the starter motor terminal. (demand)
Battery signal 3 VBREF (5V) Sensor supply
Notes - 30 RPS Input
Working input
11 VBREF GND Sensor supply
1) Wire sizing: voltage into ECM See note 7
10AWG (approx. 5mm 2 ) Main feed and return to battery pin 30 is 0.5 to 4.5
14AWG (approx. 2mm 2 ) ECM pin Nos 21.22.41.23.42.1.2
16AWG (approx. 1mm 2 ) Ignition and diagnostic socket supply Diagnostic
18AWG (approx. 0.8mm 2 ) All other circuits switch
18 AWG 18 AWG
34 STI Switch
2) Main Power Relay
16 AWG
6
97
98
Wiring diagram - 1500/1800 rev/min Switchable stand alone isochronous (non-load sharing)
6
To starter and Terminal can be
charging circuits marked 87 or G Interface harness (if used) Chassis harness connector
1 Main See note 5
power rly ECM
Emergency 10 86 85 18 AWG 18 AWG
stop device AWG 30 AMP 25 Power relay out
87
10 AWG 14 AWG
30 21 DC/DC Converter
Rating 30A 87a 14 AWG
22 (+) Feed
18 AWG
min 14 AWG
41 HSO (+) Feed
See note 4 See note 2 14 AWG
23 HSO Ground feed
+ 14 AWG
42 DPS O/P’s Ground feed
14 AWG
Battery 1 DC/DC Converter
10 AWG 14 AWG
- 2 Ground feed
5 AMP 18 AWG
Attention 37 PRE Input
12V or 24V J1
1 18 AWG
32 SCS Input (set coast)
Note: Power supply for ECM must See note 7 J2
18 AWG
be taken directly from the battery, + 31 RAS Input (resume/accel)
Diagnostic
not the starter motor terminal. Battery switch
18 AWG 18 AWG
- 34 STI Switch
Notes
On/off switch
16 AWG 5 AMP 18 AWG
1) Wire sizing:
24 VIGN - IPR (+) Feed
10AWG (approx. 5mm 2 ) Main feed and return to battery
14AWG (approx. 2mm 2 ) ECM pin Nos 21.22.41.23.42.1.2
16AWG (approx. 1mm 2 ) Ignition and diagnostic socket supply
Perkins Gen Set Power, TPD 1440E, issue 2
Request to
switch See note 2 PIN 10
+ +
shutdown
Battery Battery
See note 1
- -
On/off 10 AMP
Red 54 OWL Output (press/temp)
Additional notes
1) Maximum total current from OWL (54) output = 1 Amp (including lamp and Engine harness connector
’request to shutdown’ signal).
3) Customers must specify the relay, the wiring and appropriate fuses for 10 AMP
86 85
A
the radiator shutter control circuit. B 9 Radiator shutter
30
87 Two pin
87a connector
Radiator
shutter
Snooze (run enable) single pin connector: control relay
Packard part # Description See note 3
12065171...............Mating connector
12065249...............Secondary lock
12048159...............Male terminal 18 - 16 AWG
W1365
6
99