Professional Documents
Culture Documents
Caterpillar Cat 303.5 Mini Hydraulic Excavator (Prefix AFW) Service Repair Manual (AFW00001 and Up) PDF
Caterpillar Cat 303.5 Mini Hydraulic Excavator (Prefix AFW) Service Repair Manual (AFW00001 and Up) PDF
Models
Shutdown SIS
Previous Screen
i02763565
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 1U-7600 Slide Hammer 1
(B) 205-0633 Spanner Wrench 1
(C) 9S-9152 Bearing Puller 1
(D) 1P-0510 Driver Group 1
(E) 1P-1862 Snap Ring Pliers 1
(F) 5B-0841 Bolt 1
(G) 6B-6683 Nut 2
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in
this manual.
NOTICE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 2/20
Note: Put identification marks on the travel motor and on all lines for installation purposes. Plug
all lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the
system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the section of the travel motor for assembly purposes. The
parts must be reinstalled in the original locations of the parts.
Illustration 1 g00774455
2. Remove plug (2) , plug (3) , plug (4) , and the O-ring seals.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 3/20
Illustration 2 g00776164
3. Install Tooling (F) and (G) at opening (2a) . Use opening (3A) in order to remove wire (5) .
Illustration 3 g00775832
Illustration 4 g00776141
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 4/20
5. Remove wire (5) . through opening (3a) . Pull wire (5) and turn cover (1) in order to remove
the wire from the motor assembly.
Illustration 5 g00774466
Illustration 6 g00774472
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 5/20
Illustration 7 g00774475
Illustration 8 g00774480
Illustration 9 g00774482
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 6/20
Illustration 10 g00774486
Illustration 11 g00774487
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 7/20
Illustration 12 g00774490
Illustration 13 g00774491
Illustration 14 g00774566
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 8/20
Illustration 15 g00774575
Illustration 16 g00774577
Illustration 17 g00774580
18. Remove four bearing races (18) . Remove four washers (19) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 9/20
Illustration 18 g00775038
Illustration 19 g00774582
20. Use Tooling (B) in order to remove hidden ring nut (21) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 10/20
Illustration 20 g00774586
Illustration 21 g00774589
22. Remove four socket head screws (22) . Remove valve assembly (23) .
Illustration 22 g00774592
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 11/20
Illustration 23 g00774593
24. Remove two plugs (25) , and the O-ring seals. Remove spool (26) .
Illustration 24 g00774597
25. Remove four small O-ring seals (27) . Remove two large O-ring seals (28) .
Illustration 25 g00774603
26. Remove plug (29) , and the O-ring seal. Remove spring (30) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 12/20
Illustration 26 g00774612
27. Remove plug (31) , and the O-ring seal. Remove spool (32) .
Illustration 27 g00774614
28. Remove two plugs (33) , and the O-ring seals. Remove two springs (34) , two washers (35) ,
and spool (36) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 13/20
Illustration 28 g00774620
Illustration 29 g00774631
30. Remove six socket head bolts (40) . Remove cover (41) .
Illustration 30 g00774647
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 14/20
Illustration 31 g00774651
Illustration 32 g00774655
Note: Turn the housing on one side in order to remove the barrel assembly as a unit.
Illustration 33 g00774662
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 15/20
Illustration 34 g00774665
Note: Mark the location of the pistons in the barrel for assembly purposes.
35. Remove pistons (47) , and retainer plate (48) as a unit from barrel (45) . Remove pistons
(47) from retainer plate (48) .
Illustration 35 g00774680
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 16/20
Illustration 36 g00774674
Illustration 37 g00774683
Illustration 38 g00774688
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 17/20
Illustration 39 g00774692
Illustration 40 g00774694
41. Use a suitable press and Tooling (C) in order to remove bearing (56) from shaft (57) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 18/20
Illustration 41 g00774704
Illustration 42 g00774707
Illustration 43 g00774717
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 19/20
Illustration 44 g00774748
Note: When the plug is removed (131) steel balls will fall from the housing. Place a
receptacle under the housing in order to catch the steel balls.
44. Remove plug (61) . Remove steel balls (62) from the housing.
Illustration 45 g00774755
Illustration 46 g00774760
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - D... 20/20
Illustration 47 g00774762
Possible injury can result when removing the retaining ring and spring.
47. Use Tooling (E) and a suitable press in order to remove retaining ring (65) .
Illustration 48 g00774765
Copyright 1993 - 2020 Caterpillar Inc. Wed Mar 4 23:03:10 UTC+0800 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4
303.5 Mini Hydraulic Excavator AFW00001-UP (MACHINE)(SEBP3061 - 36) - Doc... 1/20
Shutdown SIS
Previous Screen
i02765178
Assembly Procedure
Table 1
Required Tools
(A) 8T-2683 Seal Installer 1
(B) 205-0633 Spanner Wrench 1
(C) 1U-8697 Seal Installer 1
(D) 1P-0510 Driver Group 1
(E) 1P-1862 Snap Ring Pliers 1
(F) 5B-0841 Bolt 1
(G) 6B-6683 Nut 2
(H) 9S-8864 Seal Installer 1
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/4