Professional Documents
Culture Documents
SWB7 User and Service Manual - V121
SWB7 User and Service Manual - V121
Model: SWB7
1. Please use only the original power cord or DC adapter supplied with the scale.
Other cords or adapters may damage the scale.
2. DC adaptor is used to charge the battery, and scale can operate without DC
adaptor.
3. Avoid using long power extension cords – this may cause interference
4. Do not use on surfaces or in areas where vibration, air movement or temperature
change. Do not place in direct sunlight or near air conditioning vents.
5. Avoid high humidity (greater than 80%) that might cause condensation, and keep
away from direct contact with water and other corrosive chemicals.
6. Static may influence the weighing result. To reduce the static, wipe the pan and sc
ale with anti‐static wipes.
7. Don’t impact or drop heavy objects on the scale – this may affect accuracy, or
cause damage. Do not stack material on the scale when it is not in use.
8. Battery should be removed if the scale is not used for a long period of time.
Battery should be recharged every 3 months.
9. Place items to be weighed as close to center of the pan as possible
10. Only use fingers to operate the keypad. Do not press with hard or sharp objects.
2
SWB7 USER AND SERVICE MANUAL
Warranty
Gravity Measurement, Inc. (Schenectady, New York) offers one-year limited
warranty (parts and labor) for the components failed due to defects in materials or
workmanship. Warranty starts from the date of delivery.
During the warranty period, should any repairs be necessary, the purchaser must
inform its supplier or Gravity Measurement. The company or its authorized technician
reserves the right to repair or replace the components at any of its workshops depending
on the severity of the problems. However, any freight involved in sending the faulty units
or parts to the service center should be borne by the purchaser.
The warranty will cease to operate if the equipment is not returned in the original
packaging and with correct documentation for a claim to be processed. All claims are at
the sole discretion of Gravity Measurement.
This warranty does not cover equipment where defects or poor performance is due
to misuse, accidental damage, exposure to radioactive or corrosive materials,
negligence, faulty installation, unauthorized modifications or attempted repair or failure to
observe the requirements and recommendations as given in this User Manual.
Additionally, rechargeable batteries (where supplied) are not covered under warranty.
Repairs carried out under the warranty does not extend the warranty period.
Components removed during the warranty repairs become the company property.
3
SWB7 USER AND SERVICE MANUAL
What is inside Box
AC/DC adaptor (110V)
SWB7 indicator
Two wire seals. The wire seal is used usually by the inspector of Department of Weight and
Measure or authorized dealer. The wire seal is threaded through a metal rode that protrudes
through the bottom of the device and also through a hole in the scale base adjacent to the metal
rode.
Set up
1) Place this product on a firm and smooth place, don´t place it in vibration or shaking, use
bench for use on four only adjust foot, adjust the balance using the bubble level.
2) Use independent source, avoid other electrical disturbance.
3) Don´t put any object on the platter when turn on the balance.
4) Please, turn on 2-3 minutes before using.
5) Avoid temperature change too large and air flow strenuous sites.
6) Don´t overload the balance, don´t exceed the maximal capacity.
DISPLAY DESCRIPTION
SWB7 Model:
4
SWB7 USER AND SERVICE MANUAL
BASIC FUNCTION OPERATION
Press and hold this key for 2 seconds to turn off the balance.
1. To reset the weight to zero “0”, but the display value has to be
lesser than ± 2% of maximum capacity.
2. To move one space to the left or downward in setup mode.
5
SWB7 USER AND SERVICE MANUAL
INDICATOR PC/PRINTER
1 ------------- RXD
2 ------------- TXD
3 ------------- GND
4 ------------- NC
To access to functions setting, press the and key at the same time while in
the weighing mode.
2. Press the key to view the the battery voltage or press the key to exit
6
SWB7 USER AND SERVICE MANUAL
6. Use the keys and to move cursor and press the to select number.
9. Use the keys and to move cursor and press the to select number.
Remarks: 0 0 0
A B C
A -- Buzzer on: 0= Stable not required 1= Stable required
B – LCD indicator and RELAY on: 0= Stable not required 1= Stable required
C -- Buzzer beeps when: 0= Buzzer off 1= OK 2= LO and HI
⚫ Low limit set as 0 will clear all check weigh values.
⚫ This function is locked when UF-5 is set as “HoLD 1”
Remarks: HoLd 1 :
1. Press the key will show PCT002 which means 2% of tolerance.
2. Use the keys and to move cursor and press the to select
number, this can set the range from 001 ~ 100 units of the animal hold.
3. Press the key will show TiME 8
4. Use the key to select 1,2,4,8,16,32 or 64 times within the hold range.
8
SWB7 USER AND SERVICE MANUAL
TOTAL NUMBER
OF TICKETS 0001
TOTAL
NET 2.000
9
SWB7 USER AND SERVICE MANUAL
⚫ Format 3 and format 4 if you want to print the total weight, press the key twice,
and the accumulative weight will be removed.
Communication Protocol:
UART signal of EIA-RS232 C
Format:
1. Baud rate: 9600
2. Data bits : 8 bits
3. Parity bits: None
4. Stop bits : 1 bit
Format 1 (232 1 – 3):
HEAD1 (2 BYTES) HEAD2 (2 BYTES)
OL – Overload
ST – Stable NT – Net weight
US – Unstable GS – Gross weight
10
SWB7 USER AND SERVICE MANUAL
Format 2 (232 4 ~ 6) :
Fixed 12 BYTES ASCII (kg g t lb)
1 2 3 4 5 6 7 8 1 2 1 2
DATA UNIT CR LF
DATA UNIT CR L
DATA UNIT CR LF
Output examples :
11
SWB7 USER AND SERVICE MANUAL
Modes: Zp 0 : OFF
Zp 1 : One division tracking at zero
Zp 2 : Two division tracking at zero
Zp 3 : Three division tracking at zero
Zp 4 : Four division tracking at zero
Zp 5 : Five division tracking at zero
2. If set the G value of local press the key and then press the or
1. In weight mode, press the and keys, the display will show ECF-1 .
12
SWB7 USER AND SERVICE MANUAL
4. Use the keys and to select the digit, press key to input the weight
value.
5. Put the calibration weight on the platter and press the key to calibrate.
1. Press the key to enter, display will show the calibration weight 00.2.000 .
2. Use the keys and to select the digit, and press key to input the
weight value.
3. Put the calibration weight on the platter and press the key to calibrate.
The scale will return to weighing mode automatically.
13
SWB7 USER AND SERVICE MANUAL
Keep pressing the【M+】key (not release) and turn on the indicator, after the finish of
self-checking it will display the version number -1 0 0 9 1 1 , Release the【M+】key and
the indicator will turn off automatically.
Configuration
Keep pressing key (not release) while turning on the indicator. After self-checking
*Press to quit and the indicator will restart for normal weighing mode
Make sure nothing on the platform of the scale and press to finish zero calibration
*Full capacity weights recommended for calibration of the scale, or at least 60% F.C. to
assure the accurate weighing, it’s not allowed to do with 1% F.C weight or more than
100% F.C..weight.
Place the test weights on the platform (for example, 2000 lb, or 1000 lb if you change
Finish of calibration.
Press key to enter parameter setting mode and it will display the internal A/D
value (your value is likely different from the value shown here)
262144
Press key to set the weight units 1 1 0 0 0 2 (both kg and lb units are enabled
11 0 0 0 2
ABCDEF
Press key to set the capacity of the scale 0 2 0 0 0 0 l b (the capacity of the
The above setting is for 2000 lb capacity and minimum division is 0.5 lb. The effective
Put 1/3 full capacity test weight and press to enter next step W 2
Put 2/3 full capacity test weight and press to enter next step W 3
Put 100% full capacity test weight and press to enter next step W 4
16
SWB7 USER AND SERVICE MANUAL
LF5 Zero Tracking
n o n E is for non-certified scales, and o i M L is for NTEP (United States) or OMIL (Europe)
y Reset of the zero point each time when the scale switches on
17
SWB7 USER AND SERVICE MANUAL
18
SWB7 USER AND SERVICE MANUAL
Officially Distributed By