1. The document is a user manual for waterproof EC/TDS testers that provides instructions on operation, calibration, setup, and probe replacement.
2. Key features of the testers include automatic temperature compensation, a stability indicator, low battery warning, and measurement of EC, TDS, and temperature within specified ranges and resolutions.
3. The manual provides details on operating the testers, calibrating for accuracy, setting temperature units and other parameters, and replacing probes.
1. The document is a user manual for waterproof EC/TDS testers that provides instructions on operation, calibration, setup, and probe replacement.
2. Key features of the testers include automatic temperature compensation, a stability indicator, low battery warning, and measurement of EC, TDS, and temperature within specified ranges and resolutions.
3. The manual provides details on operating the testers, calibrating for accuracy, setting temperature units and other parameters, and replacing probes.
1. The document is a user manual for waterproof EC/TDS testers that provides instructions on operation, calibration, setup, and probe replacement.
2. Key features of the testers include automatic temperature compensation, a stability indicator, low battery warning, and measurement of EC, TDS, and temperature within specified ranges and resolutions.
3. The manual provides details on operating the testers, calibrating for accuracy, setting temperature units and other parameters, and replacing probes.
1. The document is a user manual for waterproof EC/TDS testers that provides instructions on operation, calibration, setup, and probe replacement.
2. Key features of the testers include automatic temperature compensation, a stability indicator, low battery warning, and measurement of EC, TDS, and temperature within specified ranges and resolutions.
3. The manual provides details on operating the testers, calibrating for accuracy, setting temperature units and other parameters, and replacing probes.
USER MANUAL Dear Customer, FRONT PANEL & DISPLAY TECHNICAL DATA
Thank you for choosing an Adwa product.
Please read carefully this manual before Range 0.0 to 60.0 °C / 32.0 to 140.0 °F starting operations. 0 to 3999 μS/cm / 0 to 2000 ppm (AD31) This instrument is in compliance with the AD31 & AD32 0.00 to 20.00 mS/cm / 0.00 to 10.00 ppt (AD32) EMC directive 2004/108/EC and its stan- Waterproof EC/TDS Testers dards, and Low Voltage Directive 2006/95/ Resolution 0.1 °C / 0.1 °F 1 μS/cm / 1 ppm (AD31) EC and its standards for electrical equip- ments. 0.01 mS/cm / 1 ppt (AD32) For additional technical information, please Accuracy ±0.5 °C / ±1 °F e-mail us at sales@adwainstruments.com. (@25 °C/77 °F) ±2% f.s. (EC/TDS) Calibration Automatic, 1 point 1413 μS/cm, 1382 ppm or 1500 ppm (AD31) 12.88 mS/cm, 6.44 ppt or 9.02 ppt (AD32) INTRODUCTION TDS Factor User-selectable from 0.45 to 1.00 AD31 and AD32 are waterproof EC, TDS and Temperature Compensation temperature testers. The housing has been 1. Dual line LCD Automatic, from 0 to 60 °C completely sealed against humidity. 2. ON/OFF/ MODE button β adjustable from 0.0 to 2.4%/°C All EC and TDS readings are automatically 3. EC probe & temperature sensor Probe AD32P (included) temperature compensated (ATC), and 4. Probe body Battery Type 4 x 1.5V button type temperature values can be displayed in °C 5. Battery compartment (inside) Battery Life Approx. 100 hours of use or °F units. 6. SET/HOLD button Auto-off After 8 minutes of non-use The EC/TDS conversion factor (CONV) can 7. Clip holder Environment be selected by the user, as well as the coefficient -5 to 50 °C (23 to122 °F); RH 100% β (BETA) for temperature compensation. The Dimensions 175.5 x 39 x 23 mm instruments can be calibrated at one point. Weight 100 g Measurements are highly accurate with a unique stability indicator right on the LCD. The models are also provided with a low battery symbol which warns the user when PROBE & SOLUTIONS the batteries need to be replaced. The AD32P probe supplied with the meters, AD32P Spare EC probe for AD31 & is interchangeable and can be easily replaced AD32 by the user. 1. Percentage indicator for battery life AD70031P 1413 μS/cm EC standard solution The encapsulated temperature sensor allows 2. Stability indicator (hourglass symbol) 20 ml sachet (25 pcs.) fast and accurate temperature measurement 3. Low battery warning indicator and compensation. AD70030P 12.88 mS/cm EC standard solution 4. Calibrated meter indication 20 ml sachet (25 pcs.) 5. ATC (Automatic Temperature Compensation) Each meter is supplied complete with: AD70032P 1382 ppm solution TDS standard indicator 20 ml sachet (25 pcs.) • AD32P EC probe 6. Secondary LCD level 09/14
AD70442P 1500 ppm solution TDS standard
• 4 x 1.5V batteries, button type 7. Primary LCD level 20 ml sachet (25 pcs.) ISTAD31
w w w. a d w a i n s t r u m e n t s . c o m • User manual 8. Measurement unit for primary level
(ppm & μS for AD31, ppt & mS for AD32) OPERATIONAL GUIDE EC Calibration SETUP PROBE REPLACEMENT For better accuracy, frequent calibration of Turn the meter on the tester is recommended. In addition, Setup mode allows the selection of temperature The probe can be easily replaced by unscrewing • Press and hold the ON/OFF/MODE button calibration should be performed whenever the unit, TDS factor (CONV) and temperature the body as shown below. until the LCD lights up. All the used probe is replaced, after testing aggressive compensation coefficient (BETA). segments will be visible for one second chemicals and where high accuracy is required. To enter the setup mode, press the ON/OFF/ (or as long as the button is pressed), Calibration Procedure MODE button until CAL on the secondary followed by the percentage indication of • From normal EC measuring mode, press display is replaced by TEMP and the current the remaining battery life. Then the meter and hold the ON/OFF/MODE button until temperature unit (e.g. TEMP °C). Then: enter normal measurement mode. OFF on the secondary LCD is replaced by For °C/°F selection: Freeze the display CAL. • Use the SET/HOLD button. • While in measurement mode, press the • Release the button and immerse the probe • Press the ON/OFF/MODE button once to SET/HOLD button. The reading will be in the proper calibration solution set the TDS factor, twice for selecting the frozen on the LCD. Press any button to (AD70031 for AD31 and AD70030 for temperature coefficient, or three times to return to normal mode. AD32). return to the normal measuring mode. BATTERY REPLACEMENT Turn the meter off • Once the calibration has been automatically For TDS factor (CONV) selection: • While in measurement mode, press the performed, the LCD will display OK for one When the batteries become weak, the battery • After the temperature unit has been selected, ON/OFF/MODE button. OFF will appear second and the meter will return to normal symbol on the LCD lights up to indicate a press the ON/OFF/MODE button again to on the secondary display. Release the measurement mode. low battery condition. Batteries should be show the current conversion factor (e.g. button. The CAL symbol on the LCD means that the replaced soon. 0.50 CONV). meter is calibrated. To change the batteries, unscrew and release the Note: If measurements are taken in different • Press SET/HOLD to change the value. electrode body. Take out the battery compartment samples successively, rinse the probe Note: Since there is a known relationship • Press the ON/OFF/MODE button once to and carefully replace all four batteries while thoroughly to eliminate cross-con- between EC and TDS readings, it is set the temperature coefficient, or twice to paying attention to their polarity. tamination. After cleaning, rinse the not necessary to calibrate the meter return to the normal measuring mode. probe with some of the sample to be in TDS. If the conversion factor is For selecting the temperature compensation measured. either 0.5 or 0.7, the meter will allow a coefficient (BETA): direct calibration in ppm (or ppt) by • After setting the TDS factor, press the using the Adwa calibration solution ON/OFF/MODE button to show the current (see “Probe and Solution” section). temperature compensation coefficient (e.g. MEASUREMENT & CALIBRATION Note: To exit calibration and return to the 2.1 BETA). last calibration data press the ON/ • Press SET/HOLD to change the value. Taking Measurement OFF/MODE button. The secondary • Press the ON/OFF/MODE button to return • Select the desired EC or TDS mode by LCD will display “ESC” for one second to the normal measuring mode. pressing the SET/HOLD button. and the meter will return to normal • Submerge the probe in the solution to be mode. tested while stirring it gently. Note: To reset to the default calibration Reattach and tighten the electrode body properly • Measurements should be taken when the value and clear a previous calibration, to ensure a watertight seal. stability indicator (hourglass) disappears. press the SET/HOLD button after • The EC or TDS value automatically entering the calibration mode. The compensated for temperature is shown on secondary LCD will display “CLR” the primary LCD level while the secondary for one second and the meter will one shows the sample temperature. return to normal mode. The CAL symbol on the LCD will disappear. Note: Before taking any measurement, make sure the meter has been calibrated (CAL tag is displayed).