Professional Documents
Culture Documents
Cement, Lime & Mortar Testing Equipment
Cement, Lime & Mortar Testing Equipment
Cement, Lime & Mortar Testing Equipment
Testing Equipment
Fineness
To determine the fineness of cements, pozzolanas and other powdery materials, various international specifications
recommend the use of “specific area” method. In the instrument described below, air permeability method is used to
determine the specific surface as total surface area in cm²/g of material.
ELC 390
Cement Testing
Ordering Information :
ELC 390 BS Air Permeability Apparatus (Blaine Type)
ELC 390 ASTM Air Permeability Apparatus (Blaine Type)
Note: In the AIM 391-4 model, there is no onboard data acquisition and no option of changing the K factor from the keypad,
these are only possible using a computer (not included as a part of instrument).
Ordering Information :
ELC 391-3 BS/ASTM Automatic Blaine Apparatus, with inbuilt data recording and control system.
ELC 391-4 BS/ASTM Automatic Blaine Apparatus, with PC based data recording and onboard control system
E1 www.edibon.com
Fineness of Fly Ash (Wet Sieving)
Wet Sieving method is recommended for determining the Fineness of Fly Ash using 45micron sieve as recommended in
various international standards. In this instrument, wet sieving is done using 45micron Sieve, Spray Nozzle, Pressure
Gauge & Water source.
ew
Fineness Testing Apparatus
N
(Wet Sieving type) for Fly Ash
ELC 392
ELC 392
Ordering Information :
Cement Testing
ELC 392 Fineness Testing Apparatus (Wet Sieving type) for Fly Ash temperature monitoring facility
Vicat Apparatus
ELC 394
www.edibon.com E2
Gillmore Needle Apparatus
ELC 396
This operation is used for determining setting time of hydraulic cement. It consists of a base
with a vertical shaft and two horizontal arms, the lower arm being adjustable for height.
Supplied complete with one initial needle, one final needle and a glass base plate.
The equipment consist of the following replaceable parts :
ELC 39601 Initial Needle 1 / 12 inch dia. 1 / 4 lb.wt.
ELC 39602 Final Needle 1 / 24 inch dia. 1 / 4 lb.wt.
ELC 39603 Glass base plate.
ELC 396
Ordering Information :
ELC 396 Gillmore Needle Apparatus
Cement Testing
Le-chatelier Mould
ELC 400
It consists of a small split cylinder forming a mould of 30mm internal dia. and 30 mm high. On either side of the split cylinder, two
parallel indicating arms with pointed ends are fixed.
Two loops of suitable material and strength soldered to the upper half of the mould on each side of the central split is
provided to facilitate demoulding of the hardened paste specimen after test
The resilience of the mould shall be such that the action of a mass of 300g applied shall increase the distance between
the indicator ends of the needle by 17.5mm + 2.5mm without permanent deformation.
The mould is supplied complete with two glass plates and lead weight.
E3 www.edibon.com
Le-Chatelier Flask
ELC 401
Used for the determination of specific gravity of hydraulic cement as specified in IS:4031-II
Ordering Information :
ELC 401 Le-Chatelier Flask
ASTM C 151 also specifies the use of shrinkage bar moulds for the ELC 403
determination of soundness. The change in length of the specimen is
determined by Length Comparator listed in the concrete section.
Two models are offered. One is provided with stainless steel smooth
reference points while the other is provided with knurled and threaded
reference points. Both the models are available as single mould and
multiple mould compartments. Each mould is supplied complete with
base plate and two reference points per compartment of mould. ELC 407
Mould size : 25 x 25 mm section and 250 mm effective length (Distance
between two inner-most reference points)
Cement Testing
Ordering Information :
ELC 402 Shrinkage Bar Mould, single compartment with smooth reference point
ELC 403 Shrinkage Bar Mould, two compartments with smooth reference point
ELC 404 Shrinkage Bar Mould, four compartments with smooth reference point
ELC 405 Shrinkage Bar Mould, single compartment with knurled and threaded reference point
ELC 406 Shrinkage Bar Mould, two compartments with knurled and threaded reference point
ELC 407 Shrinkage Bar Mould, four compartments with knurled and threaded reference point
Optional Accessories :
ELC 40201 Set of 20, Smooth Reference Points
ELC 40501 Set of 20, Knurled and Threaded Reference Points
www.edibon.com E4
Specification :
Working Pressure : 21 ± 1kg / cm2 at 215° C
Pressure Vessel : ID 150mm X Depth 500 mm
Weight : 70 Kg
Heater : 2000 Watts
Size : 480 (W) x 580 (D) x 1100 (H)
Supply : 220V, 50Hz, 1 phase
Panel mounted PID controller with international safety certifications.
The equipment consist of the following replaceable parts :
ELC 408-203 Rubber Gasket, Viton 1 No.
ELC 408-2-01 Pressure Gauge, 0-42kg/cm2
ELC 40806-2 Safety Valve
ELC 408-205 Digital Temperature Controller
Ordering Information :
ELC 408-1 Cement Autoclave, with Digital Pressure
& temp controller
ELC 408-2 Cement Autoclave, with Analog pressure
Gauge & Digital temp controller
Optional Accessories:
ELC 374-1-DG Length Comparator, Digital
Cement Testing
Note: Autoclave for tiles can be provided on request. ELC 408-2
The Flow Table consists of a brass table top 250 ± 2.5 mm dia,
mounted on a rigid stand. The table top is reinforced with equally
spaced ribs and allowed to drop through 12mm by a ground and
hardened cam. The Motor Drive assembly using the geared motor box
is designed to rotate the cam through the shaft at 100 rpm.
Complete with Flow mould 100mm base dia, 70mm top dia and 50mm
high. The new design has better aesthetics and compact look.
For Voltage Ratings please refer Page No. A 69 ELC 411-1
Ordering Information :
ELC 410 Flow Table, Hand Operated
ELC 411-1 Flow Table, Electrically Operated
Optional Accessories:
ELC 41102 Flow Mould
E5 www.edibon.com
Sample Preparation
Digi Mortar Mixer
ELC 412-4
Special Features :
• Microprocessor Control
• Automatic or Manual modes
• Choice of automatic mixing cycles as per EN Standard
• User defined Mixing cycle
• Sand Dispenser
Cement Testing
The mixer is designed to mix mortars and cement pastes primarily to the requirements of EN 196. The mixing paddle has a
planetary motion and is driven by a motor with a microprocessor based speed and program controller. The mixer can be
operated either in an automatic or manual mode. When the mixer is used in the manual mode, the two mixing speeds can be
changed by means of a soft touch button, without switching off the motor. In the automatic mode any one of the pre-set
mixing programmes may be selected.
Also, ELC-412-4 has been designed to prepare cement mortar for strength determination as specified in IS:4031. It can
also be used in mixing lime with pozzolonic materials for determination of lime reactivity (as per IS:1727) and for uniform
mixing of soils with additives such as lime, cement.
Standard Supply includes:
Basic unit with stainless steel mixing bowl and stirrer, Program controller with status indicators to run the
Mixer in fully Automatic or Manual mixing mode.
Technical Specifications :
Rotational Speed (rpm) Planetary Speed (rpm)
Low Speed 140+/-5 62+/-5
High Speed 285+/-10 125+/-10
Ordering Information :
ELC 412-4 Automatic/Manual Digi Mortar Mixer, 5 litre nominal capacity
Note: For High Viscous Material Including Admixtures, ELC-412-2 Morter Mixer, 5ltr. capacity and ELC 412-2-S1,
10 litre capacity can be provided on request
www.edibon.com E6
Vibration Machine
ELC 418-2 & ELC 418-3
Cement Testing
Ordering Information :
ELC 418-2 Vibration Machine with built-in Digital Timer, NABL Calibrated
ELC 418-3 Vibration Machine with built-in Digital Timer, without Calibration
Optional Accessories :
ELC 41855-S1 Top attachment of vibration machine suitable for 50mm mould.
Moulding
ELC 414, ELC 417 & ELC 417-3
Cube Moulds:
For preparation of mortar and lime cubes, the following ELC 414 ELC 417
Cube Moulds are offered :
Ordering Information :
ELC 414 Mould, Steel, for 70.6 mm Cube with ISI Certification Mark as per IS:10080
ELC 417 Mould, Cast Iron for 50 mm Cube with ISI Certification Mark as per IS:10086.
ELC 417-3-CI Mould Three Gang Cast Iron for 50 mm Cube
ELC 417-3-NB Three Gang Mould Naval Brass for 2 inch cube Mould
E7 www.edibon.com
Preparation of Flexural Prisms :
(For Rilem Cembureau Test)
Ref. Standard - EN-196
Utilizes a specially designed jolting apparatus and requires the prisms to be compacted by allowing the mould to fall
through a controlled height, at the rate of 60 jolts per min. The prisms of cement and pozzolana mortars are formed
according to the standard procedure as given in the specifications.
Jolting Apparatus
ELC 421
ELC 421
Ref. Standard - EN-196-1-13454-2
The Jolting apparatus consists of a rectangular table, rigidly connected by two support arms to spindle at a horizontal
distance of 800 mm from the centre of the table. The table can be raised and allowed to fall freely by a cam which is
connected to a motor. The cam rotates at a rate of 60 rpm. A digital counter with sensor is provided, which stops the
machine after 60 jolts. Locating pins are provided for mounting the mould compartments on the table. The mould,
Cement Testing
surrounded by the hopper, can be clamped rigidly to the table. Supplied complete with mould and hopper.
The equipment consist of the following replaceable parts :
ELC 42101 Counter
ELC 42102 Aluminum hopper
ELC 422 BS/EN Jolting Mould
Ordering Information :
ELC 421 BS/EN Jolting Apparatus as per BS/EN standard.
ELC 422
www.edibon.com E8
Flexural Jig Assembly
ELC 422-F
This jig is designed for the flexural testing of 40 x 40x 160 mm mortar
prisms. The frame is fitted with a ball seating assembly to which is
attached the upper roller bearers.
The jig can be used on the complete range of Edilab compression
testing machines and has an overall height of 223 mm.
Ordering Information :
ELC 422 BS/EN Mould for Flexural Prism
ELC 300-5525 Compression Frame Jig Assembly ELC 422-F
ELC 320-5522 Flexural Jig Assembly
ELC 320-5521-01 50 mm SQ Plate Set
ELC 320-5521-01 21 inch SQ Plate Set
ELC 320-5521-01 40 mm SQ Plate Set
Demoulding Apparatus,
for demoulding the specimens.
ELC 423, ELC 424, ELC 426, ELC 428 & ELC 429
Cement Testing
ELC 428
Ordering Information :
ELC 423 Demoulding Apparatus, for demoulding the specimens.
ELC 424 Briquette Mould, Single gang with steel base plate
ELC 426 Briquette Mould, Three gang with steel base plate
ELC 428 Gauging Trowel Ref. Standard - IS:4031 Part 14, 100 to 150 mm long blade with straight edge.
Weight 210 ± 10g
ELC 429 Gauging Trowel, Ref. Standard - IS:5515, 200 mm long blade Weight 210 ± 10g
E9 www.edibon.com
The electrically operated pumping units are provided with a control knob to adjust the pace rate which can be effectively
controlled by an experienced operator during the course of testing, by observing the progress of the load gauge reading.
Rupture Test Attachment.
It is designed to test specimens of 25 x 25 x 150 mm for determining the modulus of rupture.
The attachment consists of a bearing beam on which are kept two rollers of 25mm diameter at a centre distance of
125mm the rollers are supported on brackets and are held in position by springs. The loading roller, 25 mm diameter, is
flattened on one side to sit flat on the upper platen.
Ordering Information :
ELC 430-HO M.O.R. Testing Machine Hand operated, Capacity 10kN
ELC 430 M.O.R. Testing Machine Electrically operated, Capacity 10kN
Optional Accessories :
ELC 430001 Rupture test attachment for M.O.R. Testing Machine.
ew
rectangular and square bar samples, high precision load cell for
accurate load determination of green and fired bars, digital indicator
and analysis software.
The machine has feature of pause and speed reset during the test.
Loading frame 50kN capacity machine, comprises of a rigid twin
column construction with an integral, fully variable microprocessor
controlled drive unit and LCD display with a touch sensitive keyboard.
The machine is bench mounted for ease of installation and operation.
The use of a microprocessor controlled drive system and keyboard
entry provides the Load Frame with a wide variety of features which
include pause and speed reset during test, RS232 interface for
computer control, operator programming of speed and control
functions and many other features. A robustly constructed steel case
houses the motor drive system with careful attention being given to the
prevention of ingress of water or grit. All operating controls are
mounted on the front panel of the machine which is angled and
recessed to prevent physical and environmental damage.
For Voltage Ratings please refer Page No. A 69
ELC 430-S1
Specifications of loading frame with Electronic instrumentation
:
Capacity : 50kN
Drive Mechanism : Stepper Motor Drive Microprocessor
controlled
Rate of strain : 0.00001 to 9.99999 mm/minute.
Fast Forward & Reverse : 10mm / minute
Rapid Approach Speed : 15mm / minute
Horizontal clearance : 364mm
Max. vertical clearance : 910mm
Max. Platen travel : 100mm
Dimensions (L×W×H) : 600 × 500 × 1440 mm
Weight : 85 kg. (Approx.)
Load cell capacity : 2500N and 250N
Resolution : 0.1N & 0.01N
www.edibon.com E10
Analysis Software features:
Automatic calculation of MOR for circular, rectangular and square bar.
Simple and easy to operate software with automatic Calculation & data analysis as per the calculation pre-defined in IS
standard. Detailed output report with all the necessary parameters (average, maximum, minimum per batch).
Ordering Information :
ELC-430-S1 Modulus of Raputure (MOR) Testing Machine for Ceramic
Cement Testing
Loading speed of the double lever system : 50 +/- 10 N/Sec
Flexure jaw diameter of the loading roller : 10mm
Supporting roller diameter : 10mm
ELC 434-1
Supporting roller distance : 100mm
Baffle plate span : 46mm
Ordering Information :
ELC 434-1 Cement Tensile Testing Machine
Optional Accessories :
ELC 424 Briquette mould, Single gang with steel base plate
ELC 426 Briquette mould, Three gang with steel base plate
Permeability
ELC 437 & ELC 438
E11 www.edibon.com
base plate and a top plate with the help of tension rods and nuts. The cell assembly is mounted on the stand. The top
plate is provided with an inlet and air release vent and the base plate is provided with an outlet.
A pressure chamber is fitted with a pressure regulator and a pressure gauge 0-10 kg/cm2 indicating the chamber
pressure, and a pressure gauge 0-7 kg/cm2 indicating the test pressure.
In three cell model, a pressure chamber is supplied with foot pump, whereas in six cell model, the foot pump is
not provided, as this model is intended to be used with a compressor.
Ordering Information :
ELC 437 Permeability Apparatus, three cell model, with a Foot Pump
ELC 438 Permeability Apparatus, six cell model, with an end pressure gauge
Optional Accessories:
ELC 38104 Compressor for Permeability Apparatus 15kg/cm2
ELC 38106 Compressor for Permeability Apparatus 7kg/cm2
www.edibon.com E12
Jaw Crusher
ELC 442-1
Ordering Information :
ELC 442-1 Jaw Crusher
Note: ELC 442-1-SP Single phase Jaw Crusher is also available on request
Cement Testing
Pulveriser
ELC 443-1
Features
• The new design has better aesthetics and is more
compact construction.
• Designed for grinding materials to produce fine
mesh samples.
• It is suitable to grind up to 150 micron.
• The motor & gear assembly is supported by two
nos. of bearing blocks and mounted on sliding
carriage. ELC 443-1
• The gap of two grinding wheels can be adjusted
by rotating wheel of sliding carriage.
• Ideal for use in cement and chemical industries.
Specifications:
• Dia of Grinding Wheel 175mm
• Material fo Grinding Wheel High Carbon Steel having 55-60 HRC Hardness
• Input Size of Material _
<6mm
• Output size of Material _
>150 µ
For Voltage Ratings please refer Page No. A 69
Ordering Information :
ELC 443-1 Pulveriser, New Design
E13 www.edibon.com
Hydraulic Press
ELC 915-S1
ELC 91501 Pallet Die 10 mm dia with Sample Ejector ELC 9150101 Sample Ejector for ELC 91501
ELC 91502 Pallet Die 13 mm dia with Sample Ejector ELC 9150202 Sample Ejector for ELC 91502
ELC 91503 Pallet Die 15 mm dia with Sample Ejector ELC 9150301 Sample Ejector for ELC 91503
ELC 91504 Pallet Die 20 mm dia with Sample Ejector ELC 9150401 Sample Ejector for ELC 91504
ELC 91505 Pallet Die 25 mm dia with Sample Ejector ELC 9150501 Sample Ejector for ELC 91505
ELC 91506 Pallet Die 40 mm dia with Sample Ejector ELC 9150601 Sample Ejector for ELC 91506
ELC 91507 Pallet Die 45 mm dia with Sample Ejector ELC 9150701 Sample Ejector for ELC 91507
www.edibon.com E14