Professional Documents
Culture Documents
MX-5500 de Instalacion PDF
MX-5500 de Instalacion PDF
CODE: 00ZMX7000/I1E
MX-5500N
MX-6200N
MODEL MX-7000N
CONTENTS
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
1. Configuration
A. Lineup (Main unit and option)
Finisher
(MX-FNX3)
Staple cartridge
(AR-SC2)
MX-7000N CONFIGURATION - i
B. Machine configuration
Copier memory (Local memory) (MB) 1GB
Printer memory (System memory) (MB) 896MB
Copier Standard provision
PCL printer Standard provision
PS printer Option (Product key target.)
Main body LCD Color VGA 10.4"
FAX Option (No support for some areas.)
Scanner Standard provision
Filing Standard provision
HDD Standard provision
DSPF Standard provision
Automatic duplex Standard provision
Security Option (Product key target.)
Internet Fax Option (Product key target.)
MX-7000N CONFIGURATION - ii
[1] MX-5500N/6200N/7000N
MX-7000N Service Manual
A. Bringing space
For installation of a large size machine, be sure to check that the
door size is great enough before bringing in.
B. Installing space
The following space must be provided around the machine in order
to assure machine performances and proper operations. If any
option is installed, provide the additional space for installing it.
Especially the space at the rear of the machine must be provided E. Direct rays of the sun, dust, temperature,
sufficiently. If not, the machine cannot exhibit functions against humidity, gasses, chemicals, vibration
heat and dust, causing some troubles.
(1) Temperature and humidity
This machine is designed to perform properly under the specified
30cm temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
30cm 45cm Do not install the machine near a heater, a cooler, or a humidifier.
MX-7000N MX-5500N/6200N/7000N 1 – 1
(2) Dust 2. Transit and delivery
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime. No Content Method
1 Implements, facility, and Use a forklift. (If no forklift is
manpower available, ensure manpower of four
persons or more, and use the skid
slope (DKIT-0367FCZZ)).
2 Delivery Transit must be made in packed
condition.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
3. Unpacking
(4) Gases and chemicals A. Pulling out of the main unit
Do not install the machine at a place where there are gases and 1) Remove the top case, the top cushion, the packing case, and
chemicals. Especially be careful to avoid installation near a diazo- the bundled item.
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
MX-7000N MX-5500N/6200N/7000N 1 – 2
2) Cut the four corners of the bottom case. 5) Remove the vinyl bag from the main unit.
3) Lift the main unit slightly, and remove the bottom pad R.
4) Lift the main unit slightly, and remove the bottom pad L.
MX-7000N MX-5500N/6200N/7000N 1 – 3
8) Hold the grips of main unit and pull them down in the arrow C. Pulling out of the bundled items
direction. 1) Pull out the bundled items.
1 2 3
4 5
MX-7000N MX-5500N/6200N/7000N 1 – 4
4. Installation B. Fusing heat roller pressing
A. Lock release 1) Release the lock, and open the right door.
(Tray 1, tray 2)
(Tray 3, tray 4)
NOTE: If the machine is left unused for one month or more, the
heat roller rubber may be deformed. In such a case,
release the pressure by pushing up both levers.
MX-7000N MX-5500N/6200N/7000N 1 – 5
C. Infusing the developer (color) 5) Loosen the screws, and open the cover of the process section.
1) Open the front cover.
3) Hold the drum fixing knob by the hand to not rotate, remove
the screw, and remove the drum fixing knob.
MX-7000N MX-5500N/6200N/7000N 1 – 6
9) Hold the sections (A), and remove the DV cover in the arrow 11) Install the DV cover in the arrow direction.
direction. * When installing the DV cover, be sure to engage the pawls
with the bosses.
MX-7000N MX-5500N/6200N/7000N 1 – 7
14) Install each development unit. 3) Remove the screws, and remove the toner hopper unit.
MX-7000N MX-5500N/6200N/7000N 1 – 8
6) Connect the connectors on front side and rear side. 9) Install the development unit.
7) Engage the pawls to the toner hopper unit, and install it, and fix
with the screws.
11) Close the cover of the process section.
MX-7000N MX-5500N/6200N/7000N 1 – 9
13) Install the drum fixing knob so that fit to D-cutting part, and fix 3) Close cover of the waste toner bottle section.
with the screw.
1 2
3 4 5
MX-7000N MX-5500N/6200N/7000N 1 – 10
2) Install the IL interface harness (Package part No. 4). 2) Install the paper exit tray (Package part No. 1) to the main unit,
and fix with the screws (Package part No. 5).
MX-7000N MX-5500N/6200N/7000N 1 – 11
G. Set the control level for the reference toner 5) After the data input, close the cover.
density
1) Insert the power plug into the power outlet.
2) Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit. 6) Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density.
0
TEST SIMULATION NO.25-02 CLOSE
AT DEVEVO_L_C : 128
AT DEVEVO_L_M : 128
K C M Y EXECUTE 1/1
ON
Note: Be sure to select all of the four colors: K, C, M, Y
7) Exit from Simulation mode by pressing the [CA] key on the
main unit.
4) With the front cabinet open, enter the data for Sim.25-2.
0
TEST SIMULATION NO.25-02 CLOSE
AT DEVEVO_L_K : 128
AT DEVEVO_L_C : 128
AT DEVEVO_L_M : 128
K C M Y EXECUTE 1/1
MX-7000N MX-5500N/6200N/7000N 1 – 12
H. Installation of individual color toner cartridges 4) Insert the cartridge securely until it locks.
1) Shake the toner cartridge a few times.
BK1 BK2
C 1
Y M
2
MX-7000N MX-5500N/6200N/7000N 1 – 13
K. Tray setup 5) Select "recycled" on the selection box of the "Type". Select
"A4" on the selection box of the "Size". Touch the [OK] key.
(1) Setting of paper size and paper type
Change the tray setting in the "system setting" mode. Some items System Settings
require the administrator authority for display. The paper setting (to Tray Settings Cancel OK
A4/recycle) procedure for tray 3 is as follows. Tray: Tray 3
However, if size of the tray 1 has been switched to B5, execute SIM Type:
1 Recycle Paper
26-2, and set the paper size. Size:
2 Auto-Inch
Y mm (100-297)
Paper Property:
Fixed Paper Side
HOME
Disable Duplex
Disable Staple
SYSTEM
SETTINGS
List Print
Total Count Default Settings (User)
2
3) Touch the [Tray Settings] key.
System Settings
3
Paper Type Registration
Tray 3
Type Plain
Change
1 2
Size Auto-Inch
Fixed Paper Side Disable Duplex Disable Staple Disable Punch
2
Copy Print Fax I-Fax Doc. Filing 3
Type Plain
Tray 4 Change
Size Auto-Inch
Fixed Paper Side Disable Duplex Disable Staple Disable Punch
MX-7000N MX-5500N/6200N/7000N 1 – 14
3) Fit the A4 size regulation plate to A4 size, and attach it. 2) Push down the paper feed base plate of the tray 1 gently, hold
* Be careful to place and direction that install the sheet. the hooks and remove A4 size regulation plate. Remove the
sheet.
* Double the sheet that have been removed, and store it to the
tray 2.
2
3
3
2
3) Push down the paper feed base plate of the tray 2 gently, hold
the hooks and remove A4 size regulation plate. Remove the
sheet.
3
2
2
3
4) Double the sheet that have been removed in step 2 and step 3,
and install the A4 size regulation plate.
* Double the sheet, and install it.
* Be careful to place and direction that install the sheet.
b. A4-B5 series tray 1 (A4 to B5)
* Except Europe, Australia, and New Zealand
1) Pull out the tandem cassette.
MX-7000N MX-5500N/6200N/7000N 1 – 15
5) Remove the rear end regulation plate F and R, and remove the 8) Open the waste toner bottle section cover.
screw.
6) Install the rear end regulation plate F and R, and fix with the
screw.
7) Remove the screw, and remove the mylar sheet. Change the
installing direction and install with screws. (2 positions)
11) Attach the A4 size regulation plate to inner side of the waste
1 toner bottle section cover.
MX-7000N MX-5500N/6200N/7000N 1 – 16
12) Close the waste toner bottle section cover. L. Specifications setup
Used to set the specifications with SIM26 according to the cus-
tomer's request.
SIM No Content
26 6 Used to set the destination.
To customize the following items after completion of the destination
setup, change the set values.
SIM No Content
26 2 Paper size setting of the Tray1/LCC.
3 Used to set the auditor specification mode.
5 Used to set the number (1 or 2) of count of paper
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter,
developer counter.
18 Used to set YES/NO of the toner save mode (Only
13) Close the tandem cassette.
in UK and Japan versions)
* Carry out the setting by the user's program
except the UK version.
1:accept 2:inhibit
52 Used to set whether non-printed paper (insertion
paper, cover paper) is counted up or not.
1:YES 2:NO
53 Used to set YES/NO of auto color calibration
permission.
1:accept 2:inhibit
65 Used to set the limit number of sheets for stapling.
1:limited 2:unlimited
A
EXECUTE
MX-7000N MX-5500N/6200N/7000N 1 – 17
3) Set the color patch image (adjustment pattern) paper printed in 6) Check the color balance and density.
procedure 2) on the document table. Check to insure that the printed color balance check patch
Place the printed color patch image (adjustment pattern) paper image is within the following specifications.
so that the thin lines on the paper are on the left side. At this
time, place 5 sheets of white paper on the printed color patch Fig. 1 PG image
image (adjustment pattern) paper. Low density High density
Bk
A B C D E F G H I J K L M N O Max
,
a. Note for execution of the color balance adjustment (Auto
*LIGHT AREA AT LEFT SIDE ON DOCUMENT GLASS.
adjustment)
• The copy color balance adjustment must have been completed
properly.
• Be sure to use the specified paper for color.
FACTORY SERVICE EXECUTE b. Adjustment procedure
The copy color balance adjustment is automatically executed 1) Enter the SIM 67-24 mode.
and prints the color balance check patch image.
TEST SIMULATION NO.67-24 CLOSE
5) Press [OK] key.
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
TEST SIMULATION NO. 46-24 CLOSE (PLEASE USE SPECIFIED TYPE OF A3 OR 11" 17" SIZE PAPER
FOR THIS ADJUSTMENT)
ENGINE HALFTONE AUTO ADJUSTMENT
CONFIRM THE ADJUSTED PATCH AND PRESS [OK] TO REGISTER THIS PATCH DATA
EXECUTE
MX-7000N MX-5500N/6200N/7000N 1 – 18
3) Set the color patch image (adjustment pattern) paper printed 6) Check the color balance and density.
on the document table. Check to insure that the printed color balance check patch
Place the printed color patch image (adjustment pattern) paper image is within the following specifications.
so that the thin lines on the paper are on the left side. At this
time, place 5 sheets of white paper on the printed color patch
image (adjustment pattern) paper. Fig. 1 PG image
PRINTER CALIBRATION
PRINTER CALIBRATION Y
Bk
A B C D E F G H I J K L M N O Max
OK
O. Setup and adjustment data recording
REPEAT
Print the various setup data and the adjustment data (list) with
NOTE: SIM22-6 and keep the data.
Do not cancel the simulation until "PLEASE QUIT THIS • In case of a memory trouble, if the data are not kept, all the
MODE" is displayed. adjustments must be made again.
• If the data are kept, the setup values and the adjustment values
SIMULATION NO.67-24 CLOSE can be entered without adjustments, shortening the servicing
TEST
time.
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
MX-7000N MX-5500N/6200N/7000N 1 – 19
P. Necessary works before moving the machine
1) If the following options are installed, remove all of them from
the machine.
• Large capacity tray
• Inserter
• Finisher
2) Remove the following consumable parts from the machine.
• Paper
• Toner cartridge
• Development cartridge
3) Lock the following sections.
• Scanner (Optical section)
• Paper cassette lift plate
NOTE: Since the hard disk drive is built in the machine, use care
not to exert vibrations or shocks to the machine when in
transit.
MX-7000N MX-5500N/6200N/7000N 1 – 20
[2] MX-LCX2
MX-7000N 2) Pull out gently
Service Manualthe large capacity tray until it stops.
1. Unpacking
A. Pulling out of the large capacity tray (A4) unit
1) Pull out the large capacity tray (A4) unit.
3) Remove the paper feed base fixing screw (1 pc.) of the large
capacity tray.
* Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on with-
out removing the fixing screw, a trouble may be resulted.
MX-7000N MX-LCX2 2 – 1
C. Check the packed items 3) Disconnect the power plug of the main unit from the power out-
1) Check that all the items are included in the package. let.
2 3
1
4 5
"OFF"
"OFF"
MX-7000N MX-LCX2 2 – 2
3) Release the lock, and open the right door. 6) Remove the fixing screws (2 pcs.) of the machine entry port,
and remove the entry port cover.
7) Attach the entry port cover reversely to the machine and fix it
with the two fixing screws which was removed in procedure 3).
* When working, be careful to prevent damage of the paper
pass (transport) surface on the entry port cover.
MX-7000N MX-LCX2 2 – 3
10) Close the right door. At that time, pull the large capacity tray in a right direction and
check that a large capacity tray is locked to the main body.
2) Hang the metal fixture of the large capacity tray on the lower
F R
front/rear connecting plate of the main unit side. Push the large Note 2)
capacity tray onto the main unit and attach it. Turn the lock release screw of the front cover counterclockwise to
loosen and check that the screw is free.
MX-7000N MX-LCX2 2 – 4
<<How to separate the large capacity tray from the main
unit>> R side
1) Turn the lock release screw of the front cover clockwise and
tighten the screw securely to release lock.
E. Connector connection
1) Remove the fixing screws (one for each) from the connector
cover on the main unit and then remove the two connector
covers.
2) Then hold the grips of the front and the rear cabinets with both
hands, and lift the left side. The large capacity tray will come
off.
MX-7000N MX-LCX2 2 – 5
2) Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function. F side R side
2) Loosen the fixing screw (flat screw 1pc.) of the auxiliary guide.
3) Change the mark position ( ) of the auxiliary guide and the
cassette R from A4 to LT, and fix them with the fixing screw
(flat screw, 1pc.).
F side R side
A4 LT
MX-7000N MX-LCX2 2 – 6
2) Tighten the removed rear edge shaft with the fixing screw G. Turn ON the main power switch of the main
(blue), and store it in the storage space inside the front cabi- unit
net.
1) Connect the power plug of the main unit into the power outlet.
2) Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
3) Push the paper feed tray slightly, and return the disabled stop-
per to the original position, and fix with the fixing screw (1pc.).
"ON"
ON
4) Push the large capacity tray slowly into the original position.
MX-7000N MX-LCX2 2 – 7
H. Size setting [When shifted to the front side]
Execute SIM 26-2 "Size setting" with the key operations of the main To adjust the print line in the direction A from the paper center as
unit. shown in the figure, increment the number of value. Then make a
1) The size selection menu of the large capacity tray is displayed copy to check to insure that there is no more shift. Repeat the pro-
on the operation message display. cedures until there is no shift.
2) Select the number (Size to set) on the message screen, and
input the key.
R side
I. Carry out the print off-center adjustment
(1) Adjustment with the simulation
Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. However, if the center is shifted,
carry out the following steps to adjust.
1) Set a test chart (document) on the document table properly. Direction A
R side
Direction B
F side
Item Default
Center line of image (first imageȫ
A BK-MAG Main scan print magnification ratio BK 100
(fig. 2)
B MFT Print off-center adjustment value (Manual 50
paper feed) Then make a copy to check to insure that there is no more shift.
C CS1 Print off-center adjustment value (Tray 1) 50 Repeat the procedures until there is no shift.
D CS2 Print off-center adjustment value (Tray 2) 50
* For details of the adjustment and checking procedures, refer to
E CS3 Print off-center adjustment value (Tray 3) 50
the "[6] ADJUSTMENT" on the Service Manual for main unit.
F CS4 Print off-center adjustment value (Tray 4) 50
G LCC Print off-center adjustment value 50 (2) Mechanical adjustment
(LCC) Since the off-center adjustment is performed when shipping, there
H ADU Print off-center adjustment value (ADU) 50 is basically no need to perform this adjustment. If the center is
I MULTI COUNT Number of print 1 shifted, however, the simulation is normally used. If the shift is not
J PAPER MFT Tray selection 1 : Manual paper feed 2 removed, perform the following adjustment procedure
CS 1 2 : Tray 1
1) Pull out the large capacity tray gently until it stops.
CS 2 3 : Tray 2
CS 3 4 : Tray 3
CS 4 5 : Tray 4
LCC 6 : LCC
K DUPLEX YES Duplex 0 : Selection 1
selection
NO 1 : Unselection
MX-7000N MX-LCX2 2 – 8
2) Loosen the stopper fixing screw (1 pc.) on the lower right side 2) Push the large capacity tray slowly into the original position.
of the paper feed tray to disable the stopper function. Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure:
1) Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction B (F side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each), and slightly
push the paper feed tray into the machine. Return the stopper
to the original position, and fix it with the fixing screw (1 pc.).
Slide the auxiliary guide in the direction of B by the same
dimension.
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.
3) Then pull out the paper feed tray again until it stops.
R side
R side
2) Push the large capacity tray slowly into the original position.
A Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
F side
Slightly push the paper feed tray into the machine. Return the
stopper to the original position, and fix it with the fixing screw
(1 pc.).
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.
MX-7000N MX-LCX2 2 – 9
[3] MX-LCX3
MX-7000N 3) ManuallyManual
Service pull out the cassette.
Push the shaft at the rear side of the front cabinet to release
the lock. (About 5mm)
1. Unpacking
A. Pulling out of the large capacity tray (A3) unit
1) Pull out the large capacity tray (A3) unit.
* When the lock is released, be careful the spring will push out
the cassette about 50mm.
4) Slowly pull out the paper feed base tray until it stops.
B. Removal of the fixing material and packing
parts
1) Remove the bundled items from the large capacity tray.
MX-7000N MX-LCX3 3 – 1
6) Remove the fixing screws (3 pcs.) of the paper feed table of C. Check the packed items
the LCC, and remove the cautionary note A. 1) Check that all the items are included in the package.
2 3
A
1
4
5
Note: When the power is turned on without removing the fixing
screw, remove the fixing screw and execute SIM 15.
7) Push the large capacity tray slowly into the original position.
6
7 8
2. Installation
<Note before installation>
* Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
"OFF"
"OFF"
MX-7000N MX-LCX3 3 – 2
2) Open the front cabinet of the main unit. Turn OFF the power 3) Release the lock, and open the right door.
switch in the front cabinet.
"OFF"
3) Disconnect the power plug of the main unit from the power out-
let.
4) Remove the screws, and remove the upper cover.
MX-7000N MX-LCX3 3 – 3
6) Remove the two fixing screws of the machine entry port, and 10) Close the right door.
remove the entry port cover.
7) Attach the entry port cover reversely to the machine and fix it
with the two fixing screws which was removed in procedure 3.
* When working, be careful to prevent damage of the paper
pass (transport) surface on the entry port cover.
9) Install the upper cover, and fix with screws. Rear side
MX-7000N MX-LCX3 3 – 4
a. When the height is properly adjusted: b. When the height is not properly adjusted:
When both the edges of the connecting plates on front and Use the adjustment device on the lower left side of the LCC to
rear are fit with the longest mark on the mounting plates each, adjust the height of the left caster section.
install the positioning plates (Package part No. 4) to the front Front side
and the rear sides and fix them with the fixing screw B (Pack-
age part No. 7) (1 for each side).
Front side
Rear side
Rear side
<1>
Loosen the hex washer based screws on the both ends of the
caster movable plate in the front and the rear sides.
MX-7000N MX-LCX3 3 – 5
<2> c. If the upper section of the LCC left side is locked first
Turn the adjustment screw above to adjust the height. and the positioning plate cannot be inserted :
After adjustment with the adjustment screw, tighten the screws
on the both ends of the caster movable plate which were loos-
ened in the previous procedure.
<1>
Loosen the caster screw in the lower section of the LCC right
side.
<2>
Turn the adjuster to lower the LCC right side.
<3>
NOTE: Adjust so that the marks on the left and the right sides Tighten the caster screw.
of the caster movable plate and the lead edge of the triangular Right side
hole are at the same height.
<3>
Check the height in procedure C-1). If the height is not proper, Since the LCC may be moved by the paper weight
go to <2>. If the height is proper, install the positioning plates when closing the tray, the adjuster must be securely
to the front and the rear sides and fix them with the fixing on the floor.
screws B (1 pc. for each side).
Front side
<4>
Check the height in procedure 1). If the height is not proper,
separate the LCC (the procedure is described later) and go to
"b".
If the height is proper, install the positioning plates to the front
and the rear sides with fixing screws B.
Rear side
MX-7000N MX-LCX3 3 – 6
Front side - When the upper side is not locked
Raise the adjuster on the lower side of the LCC right side until
the hole shown in the figure below comes at the center, and
check that it is locked.
* If lock is incomplete, when the power switch is turned on, the
message, "Check installation of tray 5" is displayed on the
operation panel.
Rear side
2) Check to confirm that the upper section of the LCC left side is
locked.
After checking, lower the adjuster on the lower section of the 2) Installation of the left front cabinet
LCC right side until it does not rotate.
Engage the pawls of the left front cabinet (Package part No. 5)
Locked state with the five square holes in the left front side of the LCC, and
press the left front cabinet and fix with the fixing screw C
(Package part No. 8) (1 pc.).
Adjuster section
MX-7000N MX-LCX3 3 – 7
[How to separate the LCC from the machine] 4) Push the resin cover beneath the lock section on the top of the
1) Remove the left front cabinet of the LCC. left side of the LCC and shift the LCC to the right. Release the
top lock.
2) Remove the positioning plate installed to the front and the rear
sides of the left lower side of the LCC.
Front side
D. Connector connection
1) Remove the screw (one for each) from the connector covers
on the main unit and then remove the connector covers
Rear side (2pcs.).
3) Raise the adjuster installed to the front and the rear sides of 2) Connect the large capacity tray interface harness connector
the lower section of the LCC right side. (a) and the heating heater interface harness connector (b) to
the main unit connector, and tighten the connector screw to fix
the connector.
MX-7000N MX-LCX3 3 – 8
E. Select the paper size 3) Rear edge plate size changeover
1) Slowly pull out the paper feed base tray until it stops. <1>
Lift the MC-CL handle at the top of the rear edge plate and
shift it to the desired paper size position.
<2>
Insert the lead edge of the movable shaft into the hole in the
lower section of the rear edge plate with the upper lever, and
lock the rear edge plate to the desired paper size position.
A
A4R 8.5
B4/B5
11
A3/A4
12/A3W
<3>
Push the large capacity tray slowly into the original position.
12/A3W
A3/A4
11
B4/B5
A4R 8.5
A
<2>
Move the side plate to the desired paper size position.
<3>
Slide the handle to the desired paper size position, and lock it
and tighten the wing bolt (A).
MX-7000N MX-LCX3 3 – 9
2) Open the front cabinet of the main unit. Turn ON the power
Item Default
switch in the front cabinet.
A BK-MAG Main scan print magnification ratio BK 100
B MFT Print off-center adjustment value 50
(Manual paper feed)
C CS1 Print off-center adjustment value 50
(Tray 1)
D CS2 Print off-center adjustment value 50
(Tray 2)
E CS3 Print off-center adjustment value 50
(Tray 3)
F CS4 Print off-center adjustment value 50
"ON" (Tray 4)
G LCC Print off-center adjustment value 50
(LCC)
H ADU Print off-center adjustment value (ADU) 50
I MULTI COUNT Number of print 1
J PAPER MFT Tray selection 1 : Manual paper feed 2
3) Turn ON the power switch on the operation panel. CS 1 2 : Tray 1
CS 2 3 : Tray 2
CS 3 4 : Tray 3
CS 4 5 : Tray 4
ON LCC 6 : LCC
K DUPLEX YES Duplex 0 : Selection 1
selection
NO 1 : Unselection
[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
ON shown in the figure, increment the number of value.
R side
G. Size setting
1) Check to insure that the main body is standby state, and press
the [System setting] key on the operation panel.
Direction A
2) Menu screen is displayed on the touch panel. Select the
[Paper Tray Settings].
3) Select the paper size of LCC from contents of [Paper Tray Set- F side
tings].
Center line of image (first image)
H. Carry out the print off-center adjustment (Fig. 1)
(1) Adjustment with the simulation Then make a copy to check to insure that there is no more shift.
Since the off-center adjustment has been made at shipping, there Repeat the procedures until there is no shift.
is normally no need to adjust. However, if the center is shifted, [When shifted to the rear side]
carry out the following steps to adjust.
To adjust the print line in the direction B from the paper center as
1) Set a test chart (document) on the document table properly. shown in the figure, decrement the number of value.
2) Execute SIM 50-10 (Print off center) by the key operation of
the main unit. R side
3) In SIM 50-10, the display is shown as follows to allow setting of
the print off-center adjustment value for each paper feed tray.
Direction B
F side
MX-7000N MX-LCX3 3 – 10
(2) Mechanical adjustment-1 <3>
Since the off-center adjustment has been made at shipping, there Push the large capacity tray slowly into the original position.
is normally no need to adjust. If the center is shifted, however,
adjust with the simulation. If the shift is not recovered, perform the
following steps to adjust.
<1>
Slowly pull out the paper feed base tray until it stops.
MX-7000N MX-LCX3 3 – 11
<3> 2) Set a sheet of paper on the paper feed base tray. Check that
Push the large capacity tray slowly into the original position. the front regulation plate is at the marked center, and push it in
contact with the front regulation plate. Loosen the blue screws
of the rear regulation plate.
3) Use the mark of the rear regulation plate, and fix the blue
screws at the position so that the clearance between paper
and the rear regulation plate is evenly 1mm.
NOTE: The positions of the regulation plates are even to the right
and left marks.
1mm
MX-7000N MX-LCX3 3 – 12
b. Diagonal feed adjustment [In the case of diagonal feed 2]
1) Press the lock button on the front cabinet and lower the paper Loosen the blue screw (A) on the front regulation plate.
feed base tray to the paper supply position. Pull out the tray. Referring to the degree of diagonal feed, move the regulation
plate in the direction of (+) and fix the blue screw.
A
2) Adjust the diagonal feed.
3) Set a sheet of paper on the paper feed base tray and adjust
Diagonal feed 1 Diagonal feed 2
the regulation plate width. (Refer to "a. Regulation plate width
adjustment.")
* After completion of the adjustment, check that the front regu-
Transport
lation plate and the rear regulation plate are in parallel to
direction
each other.
33
MX-7000N MX-LCX3 3 – 13
[4] MX-RBX2
MX-7000N Service Manual
1. Unpacking
A. Pulling out of the paper pass unit C. Check the packed items
1) Pull out the paper pass unit. 1) Check that all the items are included in the package.
1 2 3 4
5 6 7
8 9 10
11 12
13
MX-7000N MX-RBX2 4 – 1
2. Installation 2) Remove the toner cartridge.
"OFF"
2) Open the front cabinet of the main unit. Turn OFF the power
switch in the front cabinet.
"OFF"
2) Remove the paper holding arm and the paper exit full detec-
tion actuator.
3) Disconnect the power plug of the main unit from the power out-
let.
MX-7000N MX-RBX2 4 – 2
D. Installation of the short-circuit harness E. Installation of the reverse detection lever
* As for the following procedures, only destinations other than 1) Install the reverse detection lever (Package part No. 6).
North America, Australia, and New Zealand are required. For * Be careful of the installing direction of the reverse detection
North America and Australia, New Zealand, progress to the pro- lever.
cedure of "E. Installation of the reverse detection lever".
1) Remove the screw, and remove the switch cover.
2) Install the short harness (Package part No. 7). F. Installation of the right rail
1) Fix the right rail mounting fixture (Package part No. 5) to the
main unit with the fixing screws (Package part No. 1).
3) Install the switch cover, and fix it with the screw. 2) Engage the right rail (Package part No.10) to cut-out portion of
main frame. (Refer to (A) and (B).)
Install the right rail while pressing so that engage the projec-
tion of the main unit frame with the hole (C) in rear side of the
right rail.
* When installing, check that the reverse detection lever (D) is
in the cut-out portion in the sheet metal of the right rail.
B
A
MX-7000N MX-RBX2 4 – 3
3) Fix the right rail with the fixing screw (Package part No. 1). 2) Fix the reverse tray with the hand screw (Package part No. 3)
while holding it to upper direction.
2) Place the paper pass unit on the slide rails, and fix it with the
fixing screws (Package part No. 1).
* Fix the screws from the rear side sequentially.
2
H. Installation of the reverse tray
1) Insert the reverse tray (Package part No. 13) according to the
guide of the right rail and the left rail. 4
1
3) Push the paper pass unit into the main unit to install.
MX-7000N MX-RBX2 4 – 4
4) Insert the upper front cover (Package part No. 12) to the sup- K. Installation of the toner cartridges
porting point, and fix it with a E-ring (Package part No. 4). 1) Install the toner cartridges.
5) Fix the wire with fixing screws (Package part No. 2).
MX-7000N MX-RBX2 4 – 5
[5] MX-CFX1
MX-7000N
Service Manual
1. Unpacking
A. Removal of the inserter B. Removal of the protection material
* For removal of the inserter, manpower of two persons or more is 1) Remove the fixing tapes and protection material.
required.
1) Remove the packing cushion, and bundled items from packing
cusion.
2) Holding the upper part of the inserter by two people, pull up the
inserter, and make it stand upright.
MX-7000N MX-CFX1 5 – 1
2) Open the top door, and remove the fixing tape and protection 2. Installation
material.
<Note before installation>
* Before installing the MX-CFX1, unpack the MX-FNX3 or MX-
FNX4.
1 2 3 4
X3+P
X4+P
X4
MX-FNX4
5 6
7
2) Fix the FIN connection fixture A (Package part No. 6) to the fin-
isher with the fixing screws (Package part No. 1).
8 9
MX-7000N MX-CFX1 5 – 2
• Connection fixture F/R for MX-FNX3 C. Connection of the inserter and finisher (Punch
(Screw used for installation : Package part No.3 of MX-FNX3) unit)
1) Attach the inserter to the finisher (or Punch unit).
X3
X4
X4
3) Fix the inserter and finisher (or Punch unit) with the fixing
screw (Package part No. 4 of MX-FNX3 or MX-FNX4).
MX-7000N MX-CFX1 5 – 3
4) Close the front cover of the finisher (or Punch unit). 7) Install the rear cover of the finisher (or Punch unit) with the fix-
ing screws.
5) Remove the screws on rear side of the finisher (or Punch unit),
and remove the rear cover.
D. Install of the latch reception parts and the
positioning pin
1) Install the latch reception parts (Package part No. 8) to the
main unit with the fixing screws (Package part No. 1).
2) Install the positioning pin (Package part No. 9) to the main unit
with the fixing screws (Package part No. 3).
* Be careful to the direction of the installation.
MX-7000N MX-CFX1 5 – 4
E. Installation of the rail F. Check of the connected position of main unit
1) Engage the inserter that has installed finisher (Punch unit) to and finisher.
the main unit. 1) Put the inserter that has installed the finisher (Punch unit)
close to the main unit.
2) Release the lock, and remove the inserter from the main unit.
3) Fix the rail (Package part No. 5) to the main unit side with the
fixing screws (Package part No. 2).
MX-7000N MX-CFX1 5 – 5
4) Turn the height adjustment bolt on the rear side so that the 8) Turn the height adjustment screws on the front side so that the
height of the center of the positioning pin and the center of the fixing screw of the adjustment section on the front side may
positioning guide is fit. become the same position as a rear side.
7) Loosen the fixing screws of the adjustment section on the front G. Height adjustment of the finisher and the
side. inserter
1) Check the height of front cabinet of the inserter and front cabi-
net of the finisher.
Front
MX-7000N MX-CFX1 5 – 6
2) Check the height of rear cabinet of the inserter and rear cabi- <Adjust of the height on rear side>
net of the finisher. 6) Remove the rear cabinet of the finisher, and loosen the rear
caster fixing screws on the inserter side.
Rear
4) Turn the height adjustment bolt so that the upper cabinet may 8) Tighten the caster fixing screws.
become equal height.
MX-7000N MX-CFX1 5 – 7
H. Check the clearance of the main unit and the 3) Remove each cabinet on the front and the rear side of the fin-
inserter isher, and loosen the fixing screws of the front and rear caster
on the left side.
1) Put the inserter that has installed the finisher (Punch unit)
close to the main unit. * The adjustment procedure is different according to the
installed finisher. For details, refer to the adjustment proce-
dure of each finisher.
2) Check from back and forth to insure that the upper and lower
clearances between the main unit and the finisher are even.
MX-7000N MX-CFX1 5 – 8
5) Tighten the fixing screws of the front and rear caster on the left 3) Touch the auxiliary caster to the floor, and tighten the caster
side, and attach each cabinet on the front and the rear side of fixing screws so that the indicator scale is fit.
the finisher.
MX-7000N MX-CFX1 5 – 9
K. Connection of connector to the main unit 2) Open the front cabinet of the main unit. Turn ON the power
1) Connect one of the two connector of the finisher to the main switch in the front cabinet.
body and connect one of another to the inserter, and tighten
each screws.
"ON"
ON
MX-7000N MX-CFX1 5 – 10
[6] MX-PNX2A/B/C/D
MX-7000N 2) Open theManual
Service front cover, and open the top cover.
1. Unpacking
2
A. Pulling out of the punch unit
1) Pull out the punch unit.
MX-7000N MX-PNX2A/B/C/D 6 – 1
C. Check the packed items 2) Attach the step screw A (Package part No. 2) to the finisher.
1) Check that all the items are included in the package.
1 2 3
4 5 6
P
MX-FNX4
only
2. Installation
<Note before installation>
* Before installing the MX-PNX2, unpack the MX-FNX3 or MX- 2
FNX4.
5) Tighten the step screws bundled to the punch unit, fix the
punch unit.
MX-7000N MX-PNX2A/B/C/D 6 – 2
6) Attach the front cover mounting fixture (Package part No. 6) B. Connection of connector of the finisher and
with the fixing screws (Package part No. 3). punch unit
• In the case of the saddle stitch finisher (MX-FNX4) 1) Remove the fixing screws, and remove the rear cover.
Install it using three fixing screws (Package part No. 3) bun-
dled to punch unit.
2
3
8) Engage the pawls of the rear side of front cover (Package part
No. 5), attach the front cover with the fixing screw (Package
part No. 1).
MX-7000N MX-PNX2A/B/C/D 6 – 3
2) Install the Connection fixture R (Package part No. 8) to the 3) Check that the center of the screw hole of the punch unit is in
main unit with the fixing screws (Package part No. 4). the range of specification of an oval hole of the mounting fix-
ture in front side of main unit.
MX-7000N MX-PNX2A/B/C/D 6 – 4
3) Fix the main unit and the punch unit with the fixing screw 7) By using nippers, split the removed connector cover of the fin-
(Package part No. 4 of MX-FNX3 or MX-FNX4). isher along the perforated line.
6) Install the rear cover of punch unit with the fixing screws.
MX-7000N MX-PNX2A/B/C/D 6 – 5
I. Punch position label attachment J. Turn ON the main power switch of the main
1) Attach the punch position label to the position indicated in the unit
figure. 1) Connect the power plug of the main unit into the power outlet.
[For scanner] (Package part No. 11 of MX-FNX3 or MX-FNX4)
Reference line of
sticking label on. Edge of R part in corner
* The corner of the upper
cabinet rear part
2) Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
"ON"
edge R2.5
ON
ON
MX-7000N MX-PNX2A/B/C/D 6 – 6
[7] MX-FNX3
MX-7000N 4) Remove the
Service skid and packing cushions.
Manual
1. Unpacking
A. Removal of the finisher
* For removal of the finisher, manpower of two persons or more is
required.
1) Remove the fixing material, and remove the top case.
2) Remove the bundled items from packing cushion. 5) One person tilt the finisher, another person remove the lower
tray.
3) Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
6) Remove the other side similarly.
(Be careful to sliding worker's foot. )
MX-7000N MX-FNX3 7 – 1
B. Removal of the protection material C. Check the packed items
1) Remove the fixing tapes and protection material. 1) Check that all the items are included in the package.
1 2 3
4 5 6
7 8 9
X3
X3
10 11 12
2. Installation
<Note before installation>
* When the MX-FNX3 is installed, first install the MX-RBX2, and
then install the MX-FNX3.
* When the MX-FNX3 and MX-PNX2 is installed at the same time,
first install the MX-PNX2, and then install the MX-FNX3.
* When the MX-FNX3 and MX-CFX1 is installed at the same time,
3) Remove the screws and remove the fixing material for the
execute the installation procedure of MX-CFX1.
paper exit tray. (four positions)
MX-7000N MX-FNX3 7 – 2
A. Installation of the rail 2) Install the connection fixture F (Package part No. 7) to the
1) Install the rail (Package part No. 5) to the finisher with the fix- main unit with the fixing screws (Package part No. 3).
ing screws (Package part No. 1).
MX-7000N MX-FNX3 7 – 3
3) Check that the center of the screw hole of the finisher is in the 3) Open the front upper door.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
D. Adjustment
1) Remove the finisher from the main unit.
2) Remove the screws, slide to the left the front lower cover, and
remove it.
MX-7000N MX-FNX3 7 – 4
7) Remove the fixing tapes. 10) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
8) Loosen both of the caster fixing screws of the front side and
rear side.
11) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
MX-7000N MX-FNX3 7 – 5
12) Tighten the caster fixing screws so that the indicator scale is 15) Close the front lower door, and fix with the fixing screws.
fit.
13) Install the rear lower cover with the fixing screws.
17) Attach the front lower cover with the fixing screws.
14) Install the spanner for adjustment to inside the front lower door.
MX-7000N MX-FNX3 7 – 6
2) Open the front cover of finisher. 6) Install the Step screw B (Package part No. 4).
3) Fix the finisher to the main unit with the step screw B (Package
7) Attach the connector cover on rear side of the finisher.
part No. 4).
MX-7000N MX-FNX3 7 – 7
G. Staple position label attachment H. Turn ON the main power switch of the main
1) Attach the label to the position indicated in the figure. unit
[For scanner] (Package part No. 9) 1) Connect the power plug of the main unit into the power outlet.
2) Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
"ON"
ON
ON
MX-7000N MX-FNX3 7 – 8
[8] MX-FNX4
MX-7000N 4) Remove the
Service skid and packing cushions.
Manual
1. Unpacking
A. Removal of the saddle stitch finisher
* For removal of the saddle stitch finisher, manpower of two per-
sons or more is required.
1) Remove the fixing material, and remove the top case.
3) Holding the upper part of the saddle stitch finisher by two peo- 6) Remove the other side similarly.
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot. )
MX-7000N MX-FNX4 8 – 1
B. Removal of the protection material 2) Remove the screws and remove the fixing material for paper
1) Remove the fixing tapes and protection material. exit tray. (four positions)
3) Open the front door of the finisher, and remove the fixing tapes
and protection material.
5) Remove the screw, and remove the fixing material of the sta-
pler unit.
MX-7000N MX-FNX4 8 – 2
6) Replace the stapler unit to the original position, and close the C. Check the packed items
front door. 1) Check that all the items are included in the package.
1 2 3
4 5 6
7) Remove the fixing screws, and remove the right lower cover.
X4 7 8 9
X4
10 11 12
MX-7000N MX-FNX4 8 – 3
2. Installation 2) Install the connection fixture F (Package part No. 7) to the
main unit with the fixing screws (Package part No. 3).
<Note before installation>
* When the MX-FNX4 is installed, first install the MX-RBX2, and
then install the MX-FNX4.
* When the MX-FNX4 and MX-PNX2 is installed at the same time,
first install the MX-PNX2, and then install the MX-FNX4.
* When the MX-FNX4 and MX-CFX1 is installed at the same time,
execute the installation procedure of MX-CFX1.
MX-7000N MX-FNX4 8 – 4
3) Check that the center of the screw hole of the finisher is in the 3) Remove the cabinet fixing screw.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
D. Adjustment
1) Remove the finisher from the main unit.
5) Remove the screws, and slide to the left the front lower cabinet
2, and remove it.
MX-7000N MX-FNX4 8 – 5
7) Remove the screws, and remove the rear lower cover. 10) Remove the screw, and remove the spanner installed inside
the front door.
11) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
12) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
MX-7000N MX-FNX4 8 – 6
13) Tighten the caster fixing screws so that the indicator scale is 16) Install the front lower cabinet 1 with the fixing screws.
fit.
14) Install the rear lower cover with the fixing screws.
18) Install the spanner for adjustment to inside the front door with
screw.
15) Install the front lower cabinet 2 with the fixing screws.
MX-7000N MX-FNX4 8 – 7
E. Connection of the saddle stitch finisher 4) Close the front cover.
1) Engage the saddle stitch finisher to the main unit.
3) Fix the saddle stitch finisher to the main unit with the step
screw B (Package part No. 4).
7) Attach the connector cover on rear side of the finisher with the
fixing screw.
MX-7000N MX-FNX4 8 – 8
F. Connection of connector to the main unit H. Turn ON the main power switch of the main
1) Connect two connectors of the saddle stitch finisher to the unit
main unit, and tighten the screws. 1) Connect the power plug of the main unit into the power outlet.
2) Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
"ON"
ON
ON
[For DSPF] (Package part No. 10)
MX-7000N MX-FNX4 8 – 9
[9] MX-FRX3, MX-FRX3U
MX-7000N 2) After checking
Service Manualthat the operation panel has gone out, open the
front cabinet and turn the main power switch to the "OFF" posi-
tion.
1. Unpacking
A. Check the packed items
1) Check that all the items are included in the package.
"OFF"
2 3
4 5 6
3) Remove the power plug of the main unit from the power outlet.
No. Names of bundles Quantity
1 DOCC PWB 1
2 PROG ROM 1
3 BOOT ROM 1
4 Screw 2
5 Operation manual 1
6 Installation manual 1
2. Installation
<Note before installation>
* To enable the data security function, the product key must be
acquired.
(For the method of acquiring the product key, contact the dealer.)
* Before installing the data security kit, be sure to perform backup
of data stored in the memory (including HDD) of the main unit.
When the data security kit is installed, all the job data stored in B. Removal of the control box
the memory (including HDD) of the main unit will be lost. * If cables are connected to the control box, remove all cables.
* If the LINE indicator or the DATA indicator for the printer and 1) Remove the screw of right rear cabinet, push down the right
image transmission on the operation panel is lit or blinking, data rear cabinet. Disengage the pawls, and remove the right rear
that has not been processed remains in the memory of the main cabinet so that slide to the front side.
unit (including HDD). Output or transmit all the data to clear the
data remaining in the main unit and then start installation. (Check
to insure that neither the LINE indicator nor the DATA indicator
on the operation panel does light up or blink.)
"OFF"
"OFF"
7cm
1
2
1
3 2
1
C. Mount the data security kit ROMs
Remove the ROMs (PROG and BOOT ROMs) and replace them
with the data security kit ROMs (PROG ROM (Package part No. 2)
(A), BOOT ROM (Package part No. 3) (B)).
The PROG and BOOT ROMs are indicated with "PROG" and
3) Hold the snap band to arrow direction, and remove it, and "BOOT" on the labels on the ROMs respectively.
remove the I/F cable.
When mounting the data security kit ROMs, insert them to the
same positions in the same orientations (cut-out portion (C) is the
right side) as those before replacement until they click and ensure
that the inserted ROMs are locked with the sockets.
BOOT
1 3 PROGRAM1
PROGRAM2
PCL/BUMON
BARCODE C
2 FAX IMG EXT
PS KANJI
4) Pull out the control box until the position in which the clamp is B 2
seen. Remove the HDD-IDE cable from the clamp.
1
D. Removal of the rear cabinet upper
2
* If the fax box unit is installed, carry out the steps 1) and 2).
1) Remove the screw that secures the fax box unit.
2) Remove the fax box unit.
* If the fax box unit is installed, carry out the steps 3) and 4)
E. Installation of DOCC PWB
additionally.
1) Disconnect the 12-pin and 15-pin connectors connected to the
3) Hang the fax box unit that has been removed in step D on the
Mother PWB.
step screw.
2) Remove two screws for fixing the DOCC PWB.
4) Fix with a screw that have been removed.
2) Insert the control box until the position that fix the HDD-IDE
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
down, etc.
6) Ensure that pins 1 and 2 of the DIP switch on the DOCC PWB 3
are OFF.
2
1
A
2
1
2) Open the front cabinet of the main unit, and turn ON the main
power switch.
4) Push the control box into the main unit. Lay the finger handle.
Fix with the screws.
3 "ON"
2
1 2
2
3) Turn ON the power switch on the operation panel.
ON
5) Push into the cable to the right cabinet rear cover, and attach
it. At this time, check that the pawls are properly fitted to the
main unit.
ON
5
1 3
1. Unpacking
A. Check the packed items
1 2
2. Installation
<Note before installation>
NOTE: To enable PS3, the product key must be acquired. (For
details of the acquiring method of the product key, refer to
the distributor.)
Write down the acquired product key on the product key
sheet and pass it to the user.
B. PS3 check
1) Print the test page in PS3 fonts by the key operation of the
operation panel. (Select the PS font list by the procedures
described in the data list print printer test page of the system
setup guide.)
Check to confirm that printing is made normally.
APPLICATION
NUMBER
MACHINE
SERIAL
NUMBER
PRODUCT
KEY
MX-7000N MX-PKX1 10 – 1
[11] AR-PF1
MX-7000N 3) Disconnect
Service
let.
the power plug of the main unit from the power out-
Manual
1. Unpacking
A. Check the packed items
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
1
the operation panel does not light up or blink.
3
A. Turn OFF the power of the main unit 4
1) Turn OFF the power switch on the operation panel. 2
"OFF"
2) Open the front cabinet.Turn OFF the power switch in the front 7cm
cabinet of the main unit.
1
3 2
2
"OFF"
1
MX-7000N AR-PF1 11 – 1
3) Hold the snap band to arrow direction, and remove it, and C. Installation of the barcode font ROM PWB
remove the I/F cable. 1) Install the barcode font ROM PWB to the barcode connector.
* Check to confirm that the silver push lever extends out when
the PWB is installed.
* The connector position is indicated by the silk print on the
PWB.
BOOT
1 PROGRAM1
3 PROGRAM2
PCL/BUMON
BARCODE
FAX IMG EXT
2 PS KANJI
4) Pull out the control box until the position in which the clamp is
seen. Remove the HDD-IDE cable from the clamp.
5) Pull out the control box until the position in which the connector 1
of the HDD-IDE cable is seen. Pull the sheet, and remove the 2
HDD-IDE cable.
2) Insert the control box until the position that fix the HDD-IDE
1 cable to the clamp, put the HDD-IDE cable to the sheet (A),
2 and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
down, etc.
2
1
A
MX-7000N AR-PF1 11 – 2
* If the fax box unit is installed, carry out the steps 3). E. Turn ON the main power switch of the main
3) Connect the I/F cable to the MFP PWB. Push the I/F cable into unit
the recessed portion of the sheet metal on the control box. 1) Insert the power plug of the main unit into the power outlet.
Attach the snap band to sheet metal of the control box.
*Check that the connector is not obliquely inserted.
2
1
4) Push the control box into the main unit. Lay the finger handle.
Fix with the screws.
"ON"
3
2
1 2
ON
5) Push into the cable to the right cabinet rear cover, and attach
it. At this time, check that the pawls are properly fitted to the
main unit.
ON
5
1 3
4
F. PCL expansion font list check
1) PCL expansion font list check.
2
Select the PCL expansion font list by the procedures described
in the printer test page in the system setup guide.
Check to confirm that the barcode font list is printed.
MX-7000N AR-PF1 11 – 3
G. Font list
Font Font name Font Font name
No. No.
1 Code128TT-Regular 15 OCR-A
2 Code128-NarrowTT- 16 OCR-B
Regular
3 Code128-WideTT- 17 OCR-B-C39-Regular
Regular
4 Code39HalfInch-Regular 18 Upc-Half
5 Code39OneInch-Regular 19 Upc-Half-Bars
6 Code39QuarterInch- 20 Upc-HalfMusic
Regular
7 Code39SmallHigh- 21 Upc-HalfNarrow
Regular
8 Code39Slim-Regular 22 Upc-HalfThin
9 Code39SmallLow- 23 Upc-Tall-Regular
Regular
10 Code39SmallMedium- 24 Upc-TallBarsThin-regular
Regular
11 Code39Wide-Regular 25 Upc-TallMusicThin-
Regular
12 Codabar-Regular 26 Upc-TallNarrow-Regular
13 Interleaved2of5-Regular 27 Upc-TallThin-regular
14 Interleaved2of5-Thin- 28 ZipCodeBarcode-Regular
Regular
MX-7000N AR-PF1 11 – 4
[12] MX-AMX1
MX-7000N Service Manual
1. Unpacking
A. Check the packed items
1 2 3
2. Installation
<Note before installation>
* To enable the Application Integration Module function, the prod-
uct key must be acquired.
MX-7000N MX-AMX1 12 – 1
[13] MX-FXX1
MX-7000N * The fax boxManual
Service unit without the mark “N” for identification includes
only the step screw (Package part No.3) not for installation.
Therefore, when installing, prepare the service parts (LX-
1. Unpacking BZ1088FCZZ) in advance.
The fax box unit with the mark for identification includes the step
A. Pulling out of the fax box unit screw (Package part No. 2) for installation. Therefore, use it.
N D
Mark for identification
* About the fax box unit without the mark “D” for identification,
upgrade of the FAX (MAIN) version to 01.03.00 or later is
required.
2. Installation
<Note before installation>
* Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
(Not used
for this main unit)
1 2 3 "OFF"
4 5
2) After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” posi-
No. Names of bundles Quantity
tion.
1 Line cable 1
2 Step screw A 1
3 Step screw B (Not used for this main unit) 1
4 FAX memory 1
5 Ferrite core 1
MX-7000N MX-FXX1 13 – 1
"OFF" 1
3) Disconnect the power plug of the main unit from the power out-
let.
2
1
2) Insert the step screw into the mounting hole of the fax box unit.
Fix the fax box unit using the screw removed in step 1.
MX-7000N MX-FXX1 13 – 2
C. Removal of the control box D. Attach the FAX memory
1) Remove the screw of right rear cabinet, push down the right 1) Install the FAX memory (Package part No. 4) to the socket on
rear cabinet. Disengage the pawls, and remove the right rear the MFP PWB as shown in the figure below so that the mem-
cabinet so that slide to the front side. ory notch (A) is on the right side.
BOOT
1 PROGRAM1 A
PROGRAM2
3
4 PCL/BUMON
BARCODE
2
FAX IMG EXT
PS KANJI
1
1 2
3) Pull out the control box until the position in which the clamp is
seen. Remove the HDD-IDE cable from the clamp.
2) Insert the control box until the position that fix the HDD-IDE
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
1
* Check that the HDD-IDE cable is not twisting, hanging
2 down, etc.
4) Pull out the control box until the position in which the connector
2
of the HDD-IDE cable is seen. Pull the sheet, and remove the
HDD-IDE cable. 1
A
1
2
MX-7000N MX-FXX1 13 – 3
3) Connect the I/F cable to the MFP PWB. Push the I/F cable into 3) Push into the cable to the right cabinet rear cover, and attach
the recessed portion of the sheet metal on the control box. it. At this time, check that the pawls are properly fitted to the
Attach the snap band to sheet metal of the control box. main unit.
* Check that the connector is not obliquely inserted.
5
1 3
3
4
2
1 2
2
1 2
2
2) Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit.
3
"ON"
ON
ON
MX-7000N MX-FXX1 13 – 4
H. Set the destination and the logo type 4) Use numeric keys [0] and [1] to enter the desired 8-digit coun-
1) Switch the operation panel to the copy mode and use the key try code.
operation [P], [∗], [C], and [∗] to enter the simulation mode. After entry, press [SET], [EXECUTE], and [YES] in this order.
2) Use the numeric keys to enter [26] in the main code entry
screen shown below and press the [START] key.
TEST SIMULATION NO66-02 CLOSE
4) Press the desired destination on the touch panel and press FRANCE : 00111101 GERMANY : 00000100
[EXECUTE] to highlight it. SWEDEN : 10100101 NEWZEALAND : 01111110
MX-7000N MX-FXX1 13 – 5
3) Use the numeric keys to enter [10] in the sub-code entry
screen shown below and press the [START] key.
TEL
LINE
Ap
pro
x. 1
0 cm
MX-7000N MX-FXX1 13 – 6
[14] MX-FWX1
MX-7000N Service Manual
1. Unpacking
A. Check the packed items
1 2
2. Installation
<Note before installation>
* In order to enable the Internet Fax send function, the product key
must be acquired.
* In order to specify the address of the Internet Fax with the
PCFAX driver, the PC-FAX driver must be updated by the Inter-
net Fax expansion kit.
MX-7000N MX-FWX1 14 – 1
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
Trademark acknowledgements
Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
Windows® XP, Windows® 2000 Server, Windows® Server 2003 and Internet
Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and
other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
re
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186,
Japan