Professional Documents
Culture Documents
MDMT Calculations For A Pressure Vessel - Abdel Halim Galala PDF
MDMT Calculations For A Pressure Vessel - Abdel Halim Galala PDF
According to ASME Code, Section VIII, Division 1, Edition 2001, Addenda 2002 Sheet : 1 of 12
Designed by : Eng. Abdel Halim Galala, Design General Manager (assist.) Rev. : 0
o o
Min. Design Metal Temperature, MDMT 10 F -12 C
M1. Nozzle Mark : N4, 1-1/2"NPS, Sch. XXS, 300# WNRF(Located entirely within 0.4
a centrally
10.16
located circle of head's leg
M2. Nozzle Mark : N12 24" NPS, Sch. 30, 300# WNRF (Manhole Located at Shell0.56with Reinforcement
14.27
M3. Nozzle Mark : Leg 20"NPS, Sch. 30 (Leg Located at Shell with Reinforcement0.5 12.7
M4. Nozzle Mark : N1 10"NPS, Sch. 60, 300# WNRF (Located at Shell) 0.5 12.7
M5. Nozzle Mark : N1 8" NPS, Sch. 80 300# WNRF (Located at Shell) 0.5 12.7
M6. Nozzle Mark : N10 & N14 6" NPS, Sch. 80, 300# WNRF (Located at Shell 0.43 10.97
M7. Nozzle Mark : N3 & N7 3" NPS, Sch. 160, 300# WNRF (Located at Shell) 0.44 11.13
M8. Nozzle Mark : N6 & N9 2" NPS, Sch.160, 300# WNRF (Located at Shell) 0.34 8.74
M9. Nozzle Mark : N2, N3, N11 & N13 1-1/2" NPS, Sch.XXS, 300# WNRF (Located 0.4 at Shell
10.16
M10. Nozzle Mark : N15 1" NPS, Sch.XXS, 300# WNRF (Piping branch from N 0.36 9.09
M11. Nozzle Mark : N8A & N8B 1-1/2" NPS, Sch.XXS, 300# WNRF (Located at Shell,0.4 F 10.16
M12. Nozzle Mark : N16 1-1/2" NPS, Sch.XXS, 300# WNRF (Located at Shell, F 0.4 10.16
M13. Nozzle Mark : N5A & N5B, 1/2" NPS, Sch.XXS, 300# WNRF (Located at Leg 0.29 7.47
Note : Rest of nozzles are N17, N18 and N19 which represent the instruments for LC & LG.
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
1. Pressure Parts Materials
a. For cylindrical shell
Material ASME SA516 Grade 70
Condition Normalized
Curve D
o o
MDMT 10 F -12 C
Nominal thickness, tn (adopted thickness) 0.55118 INCH 14 MM
Point of combination of MDMT & thkickness Below, so we have to check ratio tr.E/(tn-c)
Required thickness, tr 0.235 INCH 5.968917 MM
Corrosion allowance, Cas 0.11811 INCH 3 MM
Joint efficiency, E = E* 0.85
o
MDMT without impact testing (for thickness 0.551") -51.7244 F -46.51356 oC
Ratio = tr . E / (tn -c) [Fig. UCS-66.2] 0.46123 > 0.35 [Fig. UCS-66-1]
o
Reduction in MDMT [Temp. versus ratio in Fig. UCS-66.1] 64 F 17.77778 oC
o
Adjusted MDMT w/o impact testing -115.724 F -82.06912 oC
Impact testing required ? NO
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
Note. The same condition apply for flanges B16.47, split loose
flanges of SA216 Grade WCB and LWN flanges.
[UCS-66(c)(2),(3)&(4)]
For blind flanges :
- M2, N12 24" NPS, 300# :
Material ASME SA105 Ferritic Steel
ASME/ANSI B16.5
Condition
Curve B
o o
MDMT 10 F -12 C
Blind thickness, tA 2.75197 INCH 69.9 MM
Governing thickness, tg1 = tA/4 0.68799 17.475 MM
[Fig. UCS-66.3(c)]
o
MDMT without impact testing (for thickness 2.9374016") 10.0394 F -12.20035 oC
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
e. Stud bolts :
Material ASME SA193 Grade B7
Curve 0
Size 1.25 INCH 31.75 MM
o o
MDMT 10 F -12 C
o o
Impact testing exemption [Fig. UCS-66, Bolting] -55 F -48 C
[Size 1.25" < 2.5"]
Nuts :
Material ASME SA 194 Grade 2H
Curve 0
Size 1.25 INCH 31.75 MM
o o
MDMT 10 F -12 C
o o
Impact testing exemption [Fig. UCS-66, Bolting] -55 F -48 C
[Size 1.25" < 2.5"]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
O. Lowest MDMT Without Impact Test (cont.) [UG-20(f)] , [UCS-66] & [FIG.UCS-66]
2. For Non-Pressure Parts :
Conclusion :
o o
MDMT without Impact Testing for Whole of Vessel 10 F -12 C