Professional Documents
Culture Documents
Lift Master Star450 315 Manual de Usuario
Lift Master Star450 315 Manual de Usuario
Lift Master Star450 315 Manual de Usuario
ACCESS CONTROL
RECEIVER
SPECIFICATIONS
SUPPLY VOLTAGE: 12-24 VOLTS AC OR DC
OPERATING CURRENT: 250 mA MAXIMUM
OPERATING TEMP RANGE: -40 TO +149F
(-40 TO +65C)
WARNING
FREQUENCY: 315 MHz WARNING
RELAY CONTACT RATING: 1 AMP @ 24 VOLTS AC OR DC
This device complies with FCC Rules Part 15 and IC Canada Rules
CAUTION
and Regulations. Operation is subject to the following two WARNING
conditions: (1) This device may not cause harmful interference To prevent possible SERIOUS INJURY or DEATH from
and (2) this device must accept any interference received, electrocution:
including interference that may cause undesired operation. • Be sure power is not connected BEFORE installing the
Removable memory modules and RF module are included in this receiver.
product. Jumper J2 must remain in the default position unless To prevent possible SERIOUS INJURY or DEATH from a
otherwise noted. THERE ARE NO OTHER SERVICEABLE PARTS. moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
TABLE OF CONTENTS NEVER permit children to operate, or play with remote
controls.
DESCRIPTION PAGE
• Activate gate or door ONLY when it can be seen clearly, is
Mounting Instructions for STAR450 . . . . . . . . . . . . . . . . . . . . . .1 properly adjusted, and there are no obstructions to door
Programming For STAR450 . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 travel.
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 • ALWAYS keep gate or garage door in sight until completely
Electrical Connections for STAR450 . . . . . . . . . . . . . . . . . . . . . .4 closed. NEVER permit anyone to cross path of moving gate
STAR450 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 or door.
Figure 2
STAR450 FEATURES
POWER INDICATOR
SCROLLING DASHES ON
DIGITAL DISPLAY WHEN
AC OR DC POWER IS
DIGITAL DISPLAY APPLIED TO THE UNIT.
DISPLAYS REMOTE CONTROL LOCATION
NUMBERS WHEN PROGRAMMING OR
ACCESS IS GRANTED. ALSO DISPLAYS
USER PROMPTS AND MESSAGES.
ANTENNA CONNECTION
FOR CONNECTION TO THE
DIRECT ANTENNA OR THE
DELETE KEY ANTENNA EXTENSION KIT.
USED TO DELETE A REMOTE CONTROL
FROM THE SELECTED MEMORY LOCATION
BLOCK KEY
USED TO BLOCK THE
RECEIVER FROM
GRANTING ACCESS TO
THE SELECTED REMOTE
CONTROL. REMOTE CONTROL
REMAINS IN MEMORY, AND
MAY BE UNBLOCKED IN
Add Delete Block THE FUTURE.
ADD KEY
USED TO ENTER REMOTE CONTROLS
AND ENTER RAPID LEARNTM MODE. 1 2 3
4 5 6
7 8 9 NUMERIC KEYPAD
USED FOR PROGRAMMING
STAR KEY
USED TO ENTER ADVANCED FUNCTIONS:
✱, 1- LAST REMOTE CONTROL RECEIVED
POUND KEY
✱, 2- NO. OF UNUSED MEMORY LOCATIONS
USED AS AN ESC OR EXIT KEY FOR ALL
✱, 3- NO. OF OCCUPIED MEMORY LOCATIONS
FUNCTIONS OR MODES.
✱, 4- NO. OF BLOCKED REMOTE CONTROL LOCATIONS
✱, 5- FIRST BLOCKED REMOTE CONTROL LOCATION
✱, 7- SOFTWARE VER. #
✱, 0- AUDIBLE DIAGNOSTICS OFF/ON
Add
Add
Del
Del 002 023 234
2 3 4 END
Delete Delete
PRESS ENTER LOCATION (1-450) PRESS
TO
CONFIRM
2
PROGRAMMING THE STAR450 (CONT’D)
Blocking (Unblocking) a Remote Control: To block or unblock a user.
* 6 ~6 SECONDS
END
,
PRESS SIMULTANEOUSLY
AUDIBLE DIAGNOSTICS Double Beep: Remote control is valid and programmed into STAR450
accompanied by remote control location display.
Step 1. Activate remote control.
Slow Beep: Security+® Remote control (Not programmed in STAR450).
Step 2. Listen for beep.
Long Beep: Blocked remote control.
(LED will be displayed when OFF)
No Beep: Remote control not working.
3
TROUBLESHOOTING GUIDE
Problem Probable Cause(s) Solution(s)
No display 1. Faulty/intermittent power connections 1. Check power connections
to unit Or to unit
2. No power to unit 2. Supply power to unit
No beep when Audible diagnostics may have been Press 4 and 0 keys at
transmitting turned OFF (right-most decimal point the same time
will be lit on the display)
Transmitter does 1. Transmitter not learned into system Or 1. Add transmitter to memory
not activate operator 2. Transmitter is blocked Or 2. Replace transmitter battery
3. Transmitter battery is dead
Transmitter will not 1. Memory may be full Or 1. Delete unused transmitters from memory
learn into memory 2. Transmitter may not be a recognized 2. Verify transmitter is listed in compatible
Chamberlain transmitter Or transmitters section Or
3. Transmitter battery is dead 3. Replace transmitter battery
Unit does not function, Main memory module missing or Replace main memory module
[E 1] displayed damaged
Duplication function Backup memory module missing or Replace backup memory module
does not work, damaged, if included
[E 2] displayed
Keypad does not Keypad has a stuck key Cycle power.
respond, If unit exhibits this condition again after 2
[E 3] displayed minutes, contact Technical Service.
Model 85
Transformer
To wall Model 95
To wall outlet outlet Transformer