Professional Documents
Culture Documents
12 - Muse Ed-Ts-03-0 - 090330 - TCD191-240
12 - Muse Ed-Ts-03-0 - 090330 - TCD191-240
[Meaning] The open&close signals are inputted to DCD PCB at same time [Countermeasures]
If the door is reopened 5 times continuously by photo shoe, it will be display error.
And a case that car door is opened fully as detecting ‘DOLS’ signal but system
detects that car door switch or landing door switch is closed.
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 114/127
○ Operation CPU
TCD 199 ER_PCB_Protect_Fail (Korea domestic only) Detection Application Si220
○ Speed CPU
Whenever a DOC PCB or DCL PCB is replaced in Korea, the security system in
CP request serviceman’s ID and approval number. If this requirement is not
satisfied, the PCB protection program will not removed. So, its operation shall be
locked.
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 115/127
○ Operation CPU
TCD 200 CNET LON communication trouble Detection Application Si220
○ Speed CPU
[Meaning] DPRAM communication between Main LON and i186 does not operate [Countermeasures]
1. If the trouble doesn’t disappear after system reset on DOC-140,
Check if ROM(OS ROM) of DOC-140 & ROM of main LON are
mounted correctly.
[Explanation]
1.It will detect an error if the 4th bit(DPRAM: 0x10) of input port of i186 2. If the trouble doesn’t disappear after performing 1 item above,
system is ‘HIGH’ condition and a condition that the TOKEN is not passed Replace ROM(OS ROM) of DOC-140 & ROM of main LON.
through LON continuously more than 6 cycle (180msec).
3. Replace DOC-140 even if nothing is improved after performing
2. In case the main LON CPU of DOC-140 PCB is unable to work. item 2 above.
(The 2nd bit(CNET_CPU_ERR:0x04) of input port of i186 system is
‘HIGH’ condition)
0x9300
err_count > 5
TCD 200
[Condition]
LON LED on DOC-140 will light off.
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 116/127
○ Operation CPU
TCD 202 Car communication trouble Detection Application Si220
○ Speed CPU
[Condition]
LON LEDs of DOC-140 and DCL-243 are flickering with 1.2 sec. cycle
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 117/127
○ Operation CPU
TCD 205 DES communication trouble Detection Application Si220
○ Speed CPU
[Condition]
LON_OK LED of DES PCB is hold
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 118/127
○ Operation CPU
TCD 206 ER_REAR_OPB_COM Detection Application Si220
○ Speed CPU
[Condition]
LON LEDs of DOC-140 and DCL-243 are flickering with 1.2 sec. cycle
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 119/127
○ Operation CPU
TCD 209 ER_NPLEX_MASTER_COM Detection Application Si220
○ Speed CPU
G_Signal_Wait_Counter == 0
TCD 209
2. Check the N-PLEX communication line. (SH connector)
The communication line should be twisted shield cable.
Group_Fail_Count > 3 3. Check the terminal resistor setting
(HJP-SH jumper must be connected)
[Meaning] Communication error with other car is detected in duplex operation. [Countermeasures]
HJP SH
HJP SH
SH SL SL SH
DHG-16X
DHG-16X
DHG-16X
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 121/127
○ Operation CPU
TCD 217 Hall button jam detection Detection Application Si220
○ Speed CPU
[Meaning] When hall button is being pushed continuously, the trouble is detected. [Countermeasures]
Button_Jam_Detect[0][UP_INDX]
TCD 217
Button_Jam_Detect[0][DN_INDX]
Address Floor
0x9954 1st floor ~ 8th floor UP Button
0x9955 9th floor ~ 16th floor UP Button
0x9956 17th floor ~ 24th floor UP Button
0x9957 25th floor ~ 32nd floor UP Button
0x9958 1st floor ~ 8th floor DOWN Button
0x9959 9th floor ~ 16th floor DOWN Button
0x995A 17th floor ~ 24th floor DOWN Button
0x995B 25th floor ~ 32nd floor DOWN Button
[Meaning] Communication error with all floor in hall line is detected [Countermeasures]
H_Data_Receive_Wait_Counter == 0
[Condition]
When TCD224 occurs, operation mode would be ACD26 and perform backup
operation.
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 124/127
○ Operation CPU
TCD 236 TCI LOCK trouble Detection Application Si220
○ Speed CPU
[Meaning] Abnormal E.M switch ON is detected under CAR TOP MAINT operation. [Countermeasures]
When TCD236 occurs, TOCI switch is switched to NORMAL side under Car TOP
Maintenance operation.
Part: TCD Code
MUSE ED / Trouble Shooting Ctrl No.: MUSE ED-TS-03-0
Page: 125/127
○ Operation CPU
TCD 237 CRT communication trouble Detection Application Si220
○ Speed CPU
[Explanation]
[Meaning] When elevator stops a floor, a landing door at another floor is [Countermeasures]
opened Then, it detects an error (Russia code area only)
1. Check if the Russia code application
1) In case of Si210, The following 2 options effect on this
error
[Explanation] 2) In case of Si25x and Si23x, Russia code(0042) effects on
this error
The elevator will be stop immediately under normal operation mode, the error is
hold until the main power is turned off. It does not detects this error under <<OPZX error detects Spec>>
inspection mode.
Addr Label Contents
0042 Russia Russia code application, 0x01
Normal Mode VI_OPZX
TCD240 07CA OPZX Landing door detection function
application, 0x01
803C