Professional Documents
Culture Documents
Ilustrasi Drawing Pontoon Model P20T & Specification Data Sheet
Ilustrasi Drawing Pontoon Model P20T & Specification Data Sheet
F F
E E
D D
C C
Arrangement View
B B
Three pieces
Name Date Pontoon Model 20T
Revisi Draw Eptindo 16/01/2017
A Checked Customer A
Approved PT. Petrosea TBK
Cust Approved
1/5
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
F F
E E
D D
C C
B
Bottom View B
Three pieces
Name Date Pontoon Model 20T
Revisi Draw Eptindo 16/01/2017
A Checked Customer A
Approved PT. Petrosea TBK
Cust Approved
2/5
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
F F
E E
D D
C C
B B
Arrangement View
Pontoon Model 20 Ton
Three pieces
Name Date Pontoon Model 20T
Revisi Draw Eptindo 16/01/2017
A Checked Customer A
Approved PT. Petrosea TBK
Cust Approved
3/5
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
F F
1500
A ( 0,1: 1 )
A
17
2400
5400
18
1500
E E
5 3 1 2 6
8
1000
2200
900
D Lift Balance
13 D
Right Balance
Center Pontoon
300
9
10
12 11
C
150 150
C ( 1 : 15 )
C C
14 PONTOON MATERIAL SPEC
NO DESCRIPTION MATERIAL
1 Handrail Steel pipe 32mm schd 40
2 Handrail Steel pipe 25mm schd 40
3 Kick plate FMS 100mm x 6mm
4 Stand railling Pipe 32mm schd 40
19 5 Bollards Steel pipe 4" x sch 40
6 Joining plate lifting point Mild steel plate 35mm
7 Side fload joining plate Mild steel plate 16mm
8 Heavy duty bulldozer push bar Steel pipe 8" schd 80 S.M.L.S
9 Push bar support Steel pipe 8" schd 80 S.M.L.S
20
10 Skid runner support Angle 150mm x 150mm x 15mm
11 Two full length skid runner UNP Joint 150mm x 75mm x 7,5mm
B B
12 Steel plate skid runners Plate 20mm
13 Outerskind plate R/H - L/H Mild steel plate 20' x 5' x 6mm
10710
9000
Three pieces
Name Date Pontoon Model 20T
Revisi Draw Eptindo 16/01/2017
A Checked Mr. Jaja Customer A
Approved PT. Petrosea TBK
Cust Approved
4/5
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
Material :
➢ All exterior and interior surfaces are fabricated in 8mm - 6mm mild steel standard. The eight (8) floation cells
are individually pressure -tested after completion.
➢ Complete fitted with Buffle on the interior of pontoon fabricated in 6mm
E Skid Runners : E
➢ Pontoon base is mounted on two (2) full lenght skid runners fabricated from UNP Joint for supporting the pontoon on
the pontoon on the ground. The skid runners are fitted with wear plate thickness 16mm. The skid
runners extend to a
depth below the pontoon hull.
Proof Plate:
➢ Securely attached plate 20mm, stating the unit weight.
Pushbar :
➢ At one end of the pontoon, a Bulldozer pushbar fabricated from heavy wall pipe 200 NB Schedule 80 S.M.L.S. the pushbar
extend out from the pontoon.
D D
Decking:
➢ All deck plates, including access covers are from 6mm checker plate floor plate to provide a non-skid surface.
All access covers are sealed using 5mm gasket, fastened with 12 only1/2” CAD plated bolts.
Bollards:
➢ Four 150mm high by 100mm diameter mooring bollards with 25mm diameter cross bars are provided to each comer of
the pontoon.
Lifting points:
➢ Lifting points are fitted to each end of the decking. These are also used as tie off point.
Safety handrails:
C ➢ The safety rails will be galvanize pipe schd 40 with 32mm and 25mm. The kick rail is fitted beneath C
all hand rails with strip plate FMS 100mm x 6mm.
➢ Entry point to the decking are each end the pontoon.
Three pieces
Pontoon Model 20T
Name Date
Revisi Draw Eptindo 16/01/2017
A Checked Mr. Jaja Customer A
Approved PT. Petrosea TBK
Cust Approved
5/5
A2
8 7 6 5 4 3 2 1