Professional Documents
Culture Documents
JVC Av-14f3
JVC Av-14f3
AV- 1435EE/AV-1435TEE
AV- 14FMT3/AV-1438
AV- 14FMG3/AV- 14FMG3B
SERVICE MANUAL
COLOUR TELEVISION
AV-1435EE / AV-1435TEE CG
AV-14FMT3 / AV-1438
AV-14FMG3 / AV-14FMG3B
AV-14FMG3/-A
[RM-C90] [ RM-C364GY]
[RM-C364]
CONTENTS
! SPECIFICATIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2
! SAFETY PRECAUTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3
! FEATURES・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・ 4
! FUNCTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・ 5
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
! MAIN DIFFERENCE LIST ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 7
! SPECIFIC SERVICE INSTRUCTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 8
! SERVICE ADJUSTMENTS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・ 15
! PARTS LIST ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・ 33
★ OPERATING INSTRUCTIONS
★ STANDARD CIRCUIT DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・ 2-1
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
SPECIFICATIONS
CONT ENTS
ITEM AV-14F3 / AV-1435 AV-14FMT3 / AV-1438
AV-14FMG3 / AV-14FMG3B
AV-1435EE / AV-1435TEE
AV-14FMG3/-A
Dimensions(W×H ×D) 462mm ×340.5mm ×375mm
Mass 10kg
Telet ext System FL OP (Only for AV-14 35TEE) FL OP (Only for AV-14 FMT3)
SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many 9. Isolation Check
circuits and components specially for safety purposes. For (Safety for Electrical Shock Hazard)
continued protection, no changes should be made to the original After re-ass embling the product, always perform an isolation
design unless authorized in writing by the manufacturer. check on the exposed metal parts of the cabinet (antenna
Replacement parts must be identic al to thos e used in the original terminals, video/audio input and output terminals, Control knobs,
circuits. Service should be performed by qualified pers onnel metal cabinet, screwheads, earphone jack, control shafts, etc.)
only. to be sure the product is s afe to operate without danger of
electrical shoc k.
2. Alterations of the design or circuitry of the products should not be (1) Dielectric Strength Test
made. Any design alterations or additions will void the The isolation between the AC primary circuit and all metal parts
manufacturer's warranty and will further relieve the manufacturer exposed to the us er, particularly any expos ed metal part having a
of responsibility for personal injury or property damage resulting return path to the chass is should withs tand a voltage of 3000V
therefrom. AC (r.m.s.) for a period of one sec ond.
(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an applianc e
3. Many electrical and mechanical parts in the products have rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated
special safety-related characteristics. T hese characteristics are 200V or more, for a period of one second.)
often not evident from visual inspection nor can the protection This method of test requires a test equipment not generally found
afforded by them necessarily be obtained by using replacement in the servic e trade.
components rated for higher voltage, wattage, etc. Replacement (2) Leakage Current Check
parts whic h have these special s afety characteristics are Plug the AC line c ord directly into the AC outlet (do not use a line
identified in the parts list of Servic e manual. Electrical isolation transformer during this check.). Using a " Leakage
components having su ch features ar e identified by shading Current Tester", measure the leakage current from each exposed
on the schematics and by (! ! ) on the parts list in Service metal part of the cabinet, particularly any expos ed metal part
manual. The us e of a substitute replacement which does not having a return path to the chassis , to a known good earth
have the same safety characteristics as the recommended ground (water pipe, etc.). Any leakage current must not exceed
replac ement part shown in the parts list of Service manual may 0.5mA AC (r.m.s.).
cause shock, fire, or other hazards . However, in tropic al area, this must not exceed 0.2mA AC
(r.m.s.).
4. Do n't shor t between the LIVE side ground and ISOL ATED " Alternate Check Method
(NEUTRAL) side ground or EARTH side ground when Plug the AC line c ord directly into the AC outlet (do not use a line
repairing. isolation transformer during this check.). Use an AC voltmeter
Some model's power circuit is partly different in the GND. The having 1000 ohms per volt or more sens itivity in the following
differenc e of the GND is shown by the LIVE : (") side GND, the manner. Connec t a 1500Ω 10W res istor paralleled by a 0.15µF
ISOLATED(NEUTRAL) : (#) side GND and EARTH : ($) side AC-type c apacitor between an exposed metal part and a known
GND. Don't short between the LIVE side GND and good earth ground (water pipe, etc.). Meas ure the AC voltage
ISOLATED(NEUTRAL) side GND or EARTH side GND and across the res istor with the AC voltmeter. Move the resistor
never measure with a measuring apparatus (oscilloscope etc.) connec tion to each exposed metal part, particularly any exposed
the LIVE side GND and ISOLATED(NEUTRAL) side GND or metal part having a return path to the chassis, and measure the
EARTH side GND at the s ame time. AC voltage ac ross the res istor. Now, reverse the plug in the AC
If above note will not be kept, a fuse or any parts will be broken. outlet and repeat eac h measurement. Any voltage measured
must not exc eed 0.75V AC (r.m.s.). This c orresponds to 0.5mA
5. If any repair has been made to the chassis, it is recommended AC (r.m.s.).
that the B1 setting should be checked or adjusted (See However, in tropical area, this must not exceed 0.3V AC ( r.m.s.).
ADJUSTMENT OF B1 POWER SUPPLY). This corresponds to 0.2mA AC (r.m.s.).
6. The high voltage applied to the picture tube must conform with AC VOLT MET ER
that specified in Service manual. Excessive high voltage can (HAVING 1000 Ω/V,
cause an increase in X-Ray emission, arcing and possible OR MOR E SENSIT IVITY)
component damage, therefore operation under excessive high
voltage conditions should be k ept to a minimum, or should be
prevented. If s evere arc ing occurs, remove the AC power
0.15μF AC-T YPE
immediately and determine the cause by visual inspection
(incorrect installation, cracked or melted high voltage harness,
poor soldering, etc.). To maintain the proper minimum level of PLACE T HIS PROBE
soft X-Ray emission, c omponents in the high voltage circuitry ON EACH EXPOSED
1500 Ω 10W MET AL PART
including the picture tube must be the exact replacements or
alternatives approved by the manufacturer of the c omplete GOOD EARTH GROUND
product.
No.52026 3
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
FEATURES
" New chassis design enables us e of an interactive on-screen c ontrol.
" Wide range voltage (110V~240V) AC power input.
" With AUDIO / VIDEO INPUT & OUTPUT terminal.
" MUTING button can reduce the audio level to zero instantly.
" Functional remote control to operate T V set (for channel select, volume c ontrol, power ON/OFF, etc.) from a distanc e.
" I2C bus control utilizes single chip ICs for IF, V/C, DEF. VSM PRESET, PRESET & SETUP TOUR.
" By means of AUTO PROGRAM, the TV s tations c an be s elected automatically and the TV channels can also be rearranged automatically.
" The TELETEXT SYSTEM has a built-in FLOP system. (Only for AV-1435TEE / AV-14FMT3)
" Built-in ECO MODE (ECONOMY, ECOLOGY)
In accordanc e with the brightness in a room, the brightness and / of contrast of the picture can be adjusted automatic ally to make the
optimum picture which is eas y on the eye.
" Built – in ON TIMER, RETURN + & CHILD LOCK.
IC301
VIDEO/CHROMA TU001
DECORDER TUNER
IC702
MEMORY
IC701
SCL 1/SDA1
IC821
TEXT DECORDER
4 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
FUNCTIONS
■ FRONT PANEL
1 MENU buttons
4 AI ECO sensor
6 ON TIMER lamp
7 POWER lamp
10 9 10 HEADPHONE jack
[AV-1438]
10 9 1 2 3 4 5 6 7 8
■REAR TERMINAL
1 ANT Terminal
No. 52026 5
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
■ REMOTE CONTROL UNIT
6 9 RETURN+key
15
7 10 CHANNEL -/+ key
8 16 11 POWER key
9 12 MUTING key
17
10 13 TV/TEXT key
14 MENU key
18 MENU ▲/▼ key
MENU / key
16 -/--key
18 Teletext k ey
1
1 ECO SENSOR key
2 10
2 SOUND SYSTEM key
3 11 3 COLOUR SYSTEM key
4
4 TV/VIDEO key
5 12
5 OFF TIMER key
6 6 CHANNEL SCAN k ey
7 13 7 RETURN+key
8 14 8 DISPLAY key
15 9 CHANNEL key
10 POWER key
14 MUTING key
15 MENU key
MENU ▲/▼ key
MENU -/+ key
16 VOLUME-/+ key
Except for differenc e in body colour, the Remote Control Unit
RM-C364GY and RM-C364 have exactly the same Functions.
6 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Part Name
Inst Book Di gest Manual Warranty Card Rating Label
Model Name
AV-1435EE E/R/U
AV-1435TEE
32.5MHz (5.5MHz)
AV-14FMT3 PAL / SECAM 33.5MHz (4.5MHz)
B/G, I, D/K,M E /R/A/P
NTSC3.58 / NTSC4.43 31.5MHz (6.5MHz)
32.0MHz (6.0MHz)
AV-1438 E/C/M/I
AV-14FMG3 E /R/A/P
AV-14FMG3B
Av-14FMG3/-A
No. 52026 7
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
8 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
FRONT CABI.
SPEAKER
E ( ×2)
CRT SOCKET
PWB
MAIN PWB
PWB STOPPER
POWER
CORD D
REAR
COVER
B (×
×1)
C (×
×1)
A (×
× 4)
No. 52026 9
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
REPLACEMENT OF MEMORY ICs
1. MEMORY ICs
This model uses memory ICs. This memory IC data are for proper operation of the video and deflection circuits.
When replacing memory ICs, be sure to us e ICs written with the initial values of data.
units are the same So pleas e us e the attached diagram for the RM-C90
remote control unit for the RM-C364GY & RM-C364. SYSTEM CONSTANT- Ⅲ
By the way, MENU -/+ Key functions in the same manner as for / key.
NUMBERS
PICT URE key
MODE key
(RM-C90)
10 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
SETTING OF SYSTEM CONSTANT SET
Setting value
AV-
Setting item Setting contents AV- AV- AV- AV- AV- AV- AV- AV-
14 FMG3/-
14 F3 14 35 14 35EE 14 35TEE 14 FMT3 14 38 14 FMG3 14 FMG3B
A
YES NO NO
BILINGUAL
MU MA MU
TUNER
YES NO YES
AI ECO SENSOR
E/R/A/P E/R
E/R E/C/ M/I E/R/U E/R/A/P E/C/ M/I E/R/A/P
LANGUAGE E/C/M/I E/R/U
ON OFF OF F ON
B/B SOUND
YES 10 20 ~
LOCK 180
250 240 230 ~
YES NO NO YES
COLOUR AUTO
MINT MQSS MINT
QSS
YES NO NO
ALC
TEXT RATE 10 20 40 80 20
YES NO YES
VNR
ARA CYL CYL ARA CYL
TEXT TABLE
Table 1
No. 52026 11
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
INITIAL SETTING VALUE OF SERVICE MENU
1. Ad justment of the SERVICE MENU is m ade on the basis of the initial setting values ; however, the new setting values which
set the screen in its optim um condition may differ from the initial setting.
2. Do no t change the initial Setting Values of the Setting (Adjustment) items not listed In “ADJUSTMENT”.
2. V/C
RED
1. CUT OFF GREEN -128~+127 -50
BL UE
RED
2. DRIVE -128~+127 0
BL UE
3. BRIGHT -127~+127 0
4. CONT . -63~+63 0
TV 0 0
AV-14F3
AV-1435 0 0
AV-1435EE
6. TINT AV-1435TEE -63~+63
VIDEO AV-14F MT 3
AV-1438
AV-14F MG3 +5 0
AV-14F MG3B
AV-14F MG3/-A
TV - 17(Fixed)
8. SHARP Do Not Adj. -32~+31
VIDEO +10(Fixed)
3. DEFLECTION
4.VSM PRESET
VSM pr eset
VSM mode BRIGHT STANDARD SOFT
Setting item
12 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
5. PRESET
1. C TRAP FIX 1 1 1 1
2. SHARP PEAK 0 0 0 0
3. ABL 1 1 1 1
4. GAMMA 0 0 0 0
TV 0 2 2 3
5. Y. DELAY TIME
VIDEO 0 2 0 2
TV 1 1 0 0
7. C-BPF
VIDEO 1 1 1 1
8. CW / SCP 0 0 0 0
19. VNR 15 15 15 15
22. SIF SW 0 1 1 1
No. 52026 13
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
REPLACEMENT OF IC301 (IF V/C DECODER)
" For the IC301(IF V/C DECODER) of this model, all data are written in the micr o-computer. So, write the data in the micro-
computer in accordance with the following procedures before starting adjustment.
PROCEDURES
(1) Turn the POWER OFF.
(2) Replace the IC301 with a new one.
(3) While pressing MENU button and VOL+ button ON the FRONT CABINET simultaneous ly, turn the POW ER ON. When the POWER is
turned ON, the data is written in the micro-computer immediately.
1 MENU buttons
2 CHANNEL -/+buttons
・ / ・ buttons
(MENU -/+buttons)
・ / ・ buttons)
VOLUME - /+ buttons
3
(MENU -/+ buttons)
4 AI ECO sensor
6 ON TIMER lamp
7 POWER lamp
14 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
SERVICE ADJUSTMENTS
BEFORE STARTING SERVICE ADJUSTMENT
1. There ar e 2 way of adjusting this TV: One is with the 6. Never touch any adjustment parts, which ar e not specified
REMOTE CONTROL UNIT and the other is the conventional in the list for this adjustment VRs, transfor ms, condenser s,
method using adjustment parts and components. etc.
2. The adjustment with the REMOTE CONTROL UNIT is made 7. Preparation for adjustment
on the basis of the initial setting values. The setting values Unless otherwis e specified in the adjustment instructions, preset
which adjust the screen to its optimum condition may differ the following functions with the REMOTE CONTROL UNIT.
from the initial setting values. User mode position
3. Make s ure that connection is c orrectly made to AC power
PICTURE MODE (VSM) BRIGHT
sourc e.
4. Turn on the power of the set and equipment before us e, and VNR OFF
start the adjustment proc edures after waiting at least 30 minutes. TINT / COLOUR / BRIGHT
CONT. / SHARP CENTER
5. Unless otherwise spec ified, prepare the most suitable rec eption
or input signal for adjustment. BLUE BACK OFF
OFF TIMER OFF
AI ECO SENSOR OFF
AUTO SHUT OFF OFF
ADJUSTMENT ITEMS
Ad justment item Ad justment item
No. 52026 15
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
BASIC OPERATION OF SERVICE MENU
" The adjustment using SERVICE MENU
The following adjus tment items use the SERVICE MENU in the series of the adjustment. The adjustments are made on the bas is of the
initial setting values. The adjustment values which adjust the screen to the optimum condition c an be different from the initial setting values.
With the SERVICE MENU, various s ettings c an be made, and they are broadly classified in the following items of s ettings.
1.IF ・・・・・・・ ・・・・・・・・・・・・・ ・・・ Adjustment of the IF circuits.
2.V/C ・・・・・・・ ・・・・・・・・・・・・・ ・・ Adjustment of the VIDEO/CHROMA circuit.
3.DEF ・・・・・・・ ・・・・・・・・・・・・・ ・ Adjustment of the DEFLECTION circ uit.
4.VSM PRESET ・・・・・・・ ・・・・・ Adjustment of the initial setting values of VSM condition as STANDARD, SOFT and BRIGHT.
(VSM : Video Status Memory)
5.PRESET ・・・・・・・ ・・・・・・・・・・ Adjustment of the RF circ uit [Do not adjust].
6.SETUP TOUR OFF ・・・・・・・ ・ It s hould be able to select mode (LANGUAGE and AUTO CH PRESET).
[Shou ld be OFF].
KEY ASSIGNMENT OF REMOTE CONTROL UNIT KEY ASSIGNMENT OF REMOTE CONTROL UNIT
PICT URE
MODE key
DISPLAY key MENU
▼/▲ key
MENU NUMBERS
/ key key
NUMBERS
PICT URE key
MODE key DISPLAY key
MENU
MENU ▼/▲ key
-/+key
(RM-C364GY)
(RM-C90) (RM-C364)
16 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
[Method of setting]
1. IF
[1. VCO]
① 1 Key ・・・・・・・ ・・・・・・・・・・・・・ ・・・・・ Select 1.IF.
② 1 Key ・・・・・・・ ・・・・・・・・・・・・・ ・・・・・ Select 1.VCO
③ The VCO (CW) screen will be displayed a allow mark when the AFC voltage is at a certain level.
④ DISPLAY Key・・・・・・・ ・・・・・・・・・・・ As you press this key twice, you will return to the SERVICE MENU.
6.SETUP TOUR
① By pressing the 6 key, you can change the ON or OFF ( should be OFF).
(Should be OFF)
%・ If it is ON, then you turn the TV power off, when you are turn the TV power on again.
The JVC’s logo will be shown about 15 s econds automatically.
② MENU -/+ Key ・・・・・・・ ・・・・・・・・・・ Select Language.
③ MENU ▼ Key ・・・・・・・ ・・・・・・・・・・ Auto Search.
No. 52026 17
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
SERVICE MENU FLOW CHART
DEF PAL
1. VER. POSITION **
50Hz
/ :SELECT
- / + : OPERATE DISP : EXIT
BRIGHT
TINT **
COLOUR **
BRIGHT **
CONT. **
SHARP **
/ :SELECT
- / + : OPERATE DISP : EXIT
PRESET PAL
1. C-TRAP FIX *
50Hz B/K
/ :SELECT
- / + : OPERATE DISP : EXIT
18 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
ADJUSTMENT LOCATIONS
TP-47R/G
TP-47G/R TP-47B
TP-E
E1
T
MAIN PWB
FRONT
F901
IC701 IC702
MEMORY IC
PW
DEG IC821
[On ly fo r AV-1 435 TEE / AV -1 4FMT3 ]
S
IC301 S1 HV
TU001
T
HVT
No. 52026 19
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
ADJUSTMENTS
B1 POWER SUPPLY
Measuring
Item instrument Test point Ad justment part Description
FOCUS ADJUSTMENT
Measuring
Item instrument Test point Ad justment part Description
IF CIRCUIT ADJUSTMENT
Measuring
Item instrument Test point Ad justment part Description
Ad justment Signal 1. VCO ●Please us e s ignal generator which is correct proof about the
of VCO(CW) gener ator
sending frequency.
Remote
1. Input the PAL full colour bar (210.25MHz) signal.
control unit
2. Enter the SERVICE MENU.
3. Select 1.IF from the SERVICE MENU.
4. Press 1 key and s elect 1.VCO.
VCO (CW) ***.** MHz
TOO HIGH 5. Select VCO ADJUST with MENU ▲/▼ key.
ABOVE REFERENCE 6. Press MENU -/+ key until the colour of the characters TOO
JUST REFERENCE YELLOW HIGH changes blue to yellow. Then gradually press the MENU
BELOW REFERENCE
TOO LOW -/+ key until the TOO LOW changes yellow. At this time, confirm
AFT ADJUST ** *(* *) that the value of VCO ADJUST is near +00.
VCO ADJUST ** *(* *)
7. Select AFT ADJUST with MENU ▲/▼ key.
FINE Do no t adjust
DISP : EXIT 8. Press MENU -/+ key until the characters JUST REFERENCE
changes blue to yellow.
9. Press the DISPLAY key three times to return to normal screen.
TOO HIGH
ABOVE REFERENCE
J US T R EFE RE NC E
BELOW REFERENCE
TOO LOW
20 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item instrument Test point Ad justment part Description
Ad justment Signal DELAY POINT 1. Input a blac k and white signal (colour off).
gener ator (AGC TAKE-OVER)
of DELAY 2. Enter the SERVICE MENU.
POINT Remote 3. Select 1. IF from the SERVICE MENU.
(AGC) control unit 4. Select 2. DELAY POINT by pressing the 2 key on the remote
control unit.
5. Set the setting values of the setting items as s hown bellow table.
6. Then adjust the MENU - or + key until video noise disappears.
7. Turn to other channels and make sure that there are no
irregularities.
AGC TAKE-OVER **
MATSUSHITA
NT SC 3.58 (QAU0287-001)
DELAY POINT
0~127 45
(AGC TAKE OVER)
OTHER
35
No. 52026 21
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
VIDEO / CHROMA CIRCUIT ADJUSTMENT
The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.
The setting values which adjust the scr een to the optimum condition can be different from the initial setting values.
Do no t change the initial setting values of the setting items not listed in “ADJUSTMENT”.
Measuring
Item instrument Test point Ad justment part Description
Ad justment Signal 1. CUT OFF (R) 1. Input a blac k and white signal (colour off).
gener ator
of WHITE CUT OFF (G) 2. Enter the SERVICE MENU.
BALANCE Remote CUT OFF (B) 3. Select 2. V/C from the SERVICE MENU, then selec t 1. CUT OFF
(Low light) control unit (R), (G) and (B) .
SCREEN VR 4. Set each value to initial s etting value with 4~ 9 keys of the
[IN HVT] remote control unit.
5. Press the 1 key of the remote control unit to show the single
horizontal line on screen.
6. Turn the SCREEN VR fully counter-cloc kwise, then slowly turn it
V/C PAL clockwis e to where one of a red, blue or green colour is faintly
1. CUTOFF vis ible.
(R) * **
(G) * ** 7. Use keys 4~9 of the remote c ontrol unit and adjust the other 2
(B) * ** colours which except the appeared colour to where the single
50Hz horizontal line appears white.
/ :SELECT
8. Turn the SCREEN VR to where the single horiz ontal line glows
- / + : OPERATE DISP : EXIT
faintly.
9. Press the 2 key to turn off the single horizontal line.
10. Press the DISPLAY key twice to return to the normal screen.
CUTOFF OFF
(H.LINE OFF) 1 2 3
CUTOFF ON
(H.LINE ON) G.CUTOFF( ▲ )
4 5 6 Variable Initial setting
R. CUTOFF( ▲ ) B. CUTOFF( ▲ ) Ad justment item range value
R. DRIVE( ▲ ) B. DRIVE( ▲ )
7 8 9 -128~+127
R. CUTOFF( ▼ ) B. CUTOFF( ▲ ) R -50
R. DRIVE( ▼ ) B. DRIVE( ) -128~+127
1. CUT OFF G -50
▲
G.CUTOFF( )▲
B -128 ~+127 -50
R G B
Ad justment Signal 2. DRIVE ( R) 1. Input a blac k and white signal (colour off).
gener ator
of WHITE DRIVE (B) 2. Enter the SERVICE MENU.
BALANCE Remote 3. Select 2. V/C from the SERVICE MENU.
(High light) control unit 4. Select 2. DRIVE (R) / (B) with MENU ▼/▲ key, and set each
value to initial s etting value with 4 and 7 or 6 and 9 keys of the
remote control unit.
5. Use the keys 4 and 7 or 6 and 9 to produc e a white screen
6. Press the DISPLAY key twice to return to the nomal screen.
V/C PAL
2. DRIVE (R) * **
(B) * **
Variable Initial setting
Ad justment item range value
50Hz
/ :SELECT R -128 ~+127 +0
- / + : OPERATE DISP : EXIT 2. DRIVE
B -128~+127 +0
22 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item instrument Test point Ad justment part Description
NT SC 4.43 COLOUR When NTSC 3.58 adjustment completed, NTSC 4.43 will be
automatic ally set at the respective values.
No. 52026 23
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item Test point Ad justment part Description
instrument
Ad justment Signal TP-47G/R 5. COLOUR [Method of adjustm ent using measur ing instrument]
of SUB gener ator
COLOUR Ⅱ Oscillo- TP-E (#
#) PAL COLOUR 1. Input a PAL full field colour bar signal (75% white).
scope [CRT SOCKET
PWB] 2. Enter the SERVICE MENU.
Remote 3. Select 2. V/C from SERVICE MENU.
control unit 4. Select 5. COLOUR with the MENU ▼/▲ key.
5. Set the initial setting value of PAL COLOUR with the MENU
- / + key.
6. Connect the osc illosc ope between TP-47G/R and TP-E ( #).
B 7. Adjust PAL COLOUR to bring the value of (A) in the illustration
R to +12V(W-G). (Voltage value between (W) and (G))
Mg
(-)
0V
W
Y (A)
(+)
Cy
G
SECAM COLOUR 1. Input a SECAM full field colour bar signal (75% white).
2. Set the initial s etting value of SECAM COLOUR with the MENU
- / + key.
3. Adjust SECAM COLOUR to bring the value of (A) in the
illustration to +10V(W-G). (Voltage value between (W) and (G))
NT SC 3.58 COLOUR 1. Input a NTSC 3.58 full field colour bar signal (75% white).
2. Set the initial setting value of NTSC 3.58 COLOUR with the
MENU - / + key.
3. Adjust NTSC 3.58 COLOUR to bring the value of (A) in the
illustration to +10V(W-G). (Voltage value between (W) and (G))
NT SC 4.43 COLOUR When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values .
24 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item instrument Test point Ad justment part Description
Remote NT SC 3.58 T INT 1. Input a NTSC 3.58 full field colour bar signal (75% white).
control unit 2. Enter the SERVICE MENU.
3. Select 2. V/C from SERVICE MENU.
4. Select 6. TINT with the MENU ▼/▲ key.
5. Set the initial s etting value of NTSC 3.58 with the MENU - / +
key.
6. If you cannot get the best tint with the initial s etting value, make
fine adjustment until you get the best tint.
NT SC 4.43 TINT When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values .
Ad justment Signal TP-47G/R 6. TINT [Method of adjustm ent using measur ing instrument]
of TINTⅡ
Ⅱ gener ator TP-E (#
#)
Oscillo- [CRT NT SC 3.58 T INT 1. Input a NTSC 3.58 full field colour bar signal (75% white).
scope SOCKET 2. Enter the SERVICE MENU.
PWB]
3. Select 2. V/C from SERVICE MENU.
Remote
control unit 4. Select 6. TINT with the MENU ▼/▲ key.
5. Set the initial s etting value of NTSC 3.58 with the MENU - / +
key.
6. Connect the osc illosc ope between TP-47G/R and TP-E. (#).
7. Adjust NTSC 3.58 TINT to bring the value of (B) in the
illustration +9V(W- Cy). (Voltage value between (W) and (Cy))
B
R
Mg
(-)
0V
W (B)
Y
Cy (+)
G
NT SC 4.43 TINT When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values .
No. 52026 25
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item instrument Test point Ad justment part Description
COLOUR
ON
1 2 3
COLOUR
OFF
4 5 6
7 8 9
26 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
DEFLECTION CIRCUIT ADJUSTMENT
" There are 2 modes of adjustment (s etting value) ------ ① 50Hz mode and ② 60Hz mode ----- depending upon the kind of s ignals
(vertic al frequency 50Hz / 60Hz).
" When adjusted in mode ① , mode ② will be automatically s et.
The setting (adjustmen t) usin g the REMOTE CONTROL UNIT is made on the basis of the initial setting values.
The setting values which adjust the screen to the optimum condition can be differ ent fr om the initial settin g values.
Measuring
Item instrument Test point Ad justment part Description
Scre en size
Scre en Picture
size size
92% 10 0%
V'
Fig.2
No. 52026 27
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Measuring
Item instrument Test point Ad justment part Description
Ad justment Signal 4. VER. L IN. ● When the vertical linearity has been deteriorated
gener ator
of VER. LIN. 5. VER. SCURVE rem arkably, perform the following steps.
& VER. Remote 15. Input a cross -hatch signal.
SCURVE control unit
16. Select 4. VER. LIN. with the MENU ▼/▲ key.
17. Set the initial s etting value of 4. VER LIN. with the MENU - / +
key.
T OP 18. Select 5. VER. SCURVE with the MENU ▼/ ▲ key.
19. Set the initial setting value of 5. VER. SCURVE with the MENU
- / + key.
20. Adjust 4. VER. LIN. and 5. VER. SCURVE so that the spaces
CEN TER
of each line as shown in Fig.3 on TOP, CENTER and
BOTTOM become uniform.
BOTT OM
Make sure that the adjustment is properly done on the screen of
Fig.3 60Hz mode.
[NOTE]
" Adjust to make both 50Hz & 60Hz are the same v. size and
fine straight line.
" When adjust again, adjust 50Hz mode first.
" When adjust in 60Hz mode, only 60Hz mode is adjust.
Measuring
Item Test point Ad justment part Description
instrument
• VSM PRESET
28 No. 52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
PURITY / CONVERGENCE ADJUSTMENT
PURITY ADJUSTMENT
W EDGE
DEF LECT ION
2. Loosen the retainer screw of the deflec tion yoke. YOKE
P
3. Remove the wedges.
CR T
4. Input a green raster signal from the signal generator, and turn 46
# P/C MAGNETS
6. Bring the long lug of the purity magnets on the short lug and
P : PURITY MAGNET
position them horizontally. (Fig.2) 4 : 4 POLES (convergence magnets)
6 : 6 POLES (convergence magnets)
7. Adjust the gap between two lugs so that the GREEN RASTER Fig.1
will come into the c enter of the screen. (Fig.3)
8. Move the deflection yoke forward, and fix the pos ition of the
deflection yoke so that the whole screen will bec ome green.
9. Ins ert the wedge to the top side of the deflection yoke so that it
will not move.
PURIT Y MAGNET S
Short lug
12. Input red and blue raster signals, and make sure that purity is
Bring the long lug over the short lug
properly adjusted. and position them horizontally.
Fig.2
(F RONT VIEW )
GREEN RASTER
CEN TER
Fig.3
No. 52026 29
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
Fig.1
(F RONT VIEW )
2. Move the deflection yoke left to right and overlap the lines in the
GREEN GREEN
periphery. (Fig. 3)
RED BLUE
Fig.2
● After adjustment, fix the wedge at the original position. (F RONT VIEW )
Fasten the retainer screw of the deflection yoke.
Fix the 6 magnets with glue. GREEN GREEN
RED BLUE BLUE RED
RED
GREEN
BLUE
BLUE
GREEN
RED
Fig.3
30 No.52026
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
REPLACEMENT OF CHIP COMPONENT
! CAUTIONS
1. Avoid heating for more than 3 seconds.
2. Do not rub the electrodes and the resist parts of the pattern.
3. When removing a c hip part, melt the s older adequately.
4. Do not reuse a chip part after removing it.
! SOLDERING IRON
1. Use a high ins ulation s oldering iron with a thin pointed end of it.
2. A 30w s oldering iron is rec ommended for easily removing parts.
! REPLACEMENT STEPS
1. How to remove Chip parts 2. How to install Chip parts
$ Resistors, capacitors, etc $ Resistors, capacitors, etc
(1) As shown in the figure, push the part with tweezers and (1) Apply solder to the pattern as indic ated in the figure.
alternately melt the solder at each end.
(2) Grasp the chip part with tweezers and plac e it on the s older.
(2) Shift with tweezers and remove the chip part. Then heat and melt the solder at both ends of the chip part.
$ Transistors, diodes, variable r esistor s, etc $ Transistors, diodes, variable r esistor s, etc
(1) Apply extra solder to each lead. (1) Apply solder to the pattern as indic ated in the figure.
(2) Grasp the chip part with tweezers and place it on the solder.
(3) First s older lead A as indicated in the figure.
SOLD E R SOLD E R
A
(2) As shown in the figure, push the part with tweezers and B
alternately melt the solder at each lead. Shift and remove the
chip part. C
C
Note : After removing the part, remove remaining solder from the
pattern.
No.52026 31
AV-14F3/AV-1435
AV-1435EE/AV-1435TEE
AV-14FMT3/AV-1438
AV-14FMG3/AV- 14FMG 3B
32 No.52026