Professional Documents
Culture Documents
Intumescent Steel Coating: Fast Track, On-Site
Intumescent Steel Coating: Fast Track, On-Site
Yu4 (K2)
CAW G12
Uniclass JM61:L68116
SC902
in dry atmospheric conditions using
abrasive of suitable type and size,
Description
free from fines, moisture and oil.
SC902 is a low VOC, one coat, high build
Continue blasting until finish complies
system, based on patented technology.
with Swedish Standard SIS 05 59 00, Intumescent
preparation grade SA 2.5 or ISO 8501-1.
Usage / Purpose
• Coat blasted steel within 2 weeks. Steel Coating
It provides a fast cure effective structural
fire performance, for steelwork, up to a
All surfaces to be coated should be Fast Track, On-Site
clean, dry and free from loose friable
120 minute fire rating.
materials and any other contaminants
SC902 is designed to provide upto 120
likely to impair adhesion.
minutes fire resistance to ‘I’ section
• Nullifire recommends and have tested
beams, columns, hollow columns,
a number of primers depending on
concrete filled hollow columns and
the application. Refer to the Approved
cellular beams. As a fast-track coating,
Primer list from Nullifire Technical
all 120 minute loadings are possible
Services.
to apply in a single coat and weather
• The system is not suitable for use over
resistant in one hour.
single pack primers and compatibility
with 2 pack primers should be checked
Finish
with Nullifire Technical Services.
Can be applied to a smooth matt finish.
• For use over galvanised surfaces
A compatible top seal can be applied if a
or other substrates please contact
decorative finish is required.
Nullifire Technical Services.
Colour
Application Conditions
Part A: White
• Ensure adequate through ventilation
Part B: Translucent Black
during application
Mixed: Off-white
• Application temperature range -5°C to
Cured: Off-white Key Benefits Summary
+35°C, relative humidity <95% and a
steel surface temperature at least 3°C
Packaging
above the dew point. • Fast cure, even below 0°C,
Part A 22.3 kg pail touch dry in 1 hour
Part B 2.7 kg tin
Application Equipment
Graco Mark V or equivalent
• Early weather resistance,
Environmental Considerations shower proof within 1 hour
Low VOC and no solvent entrapment or
Mixing • Self-priming system tolerant
prolonged solvent odour. of light rusting to steel, up to 2
• Always mechanically mix product in
full pack volumes. weeks post blasting
Availability
• Ensure the two components are • High build potential with
Only available to Nullifire Specialist
thoroughly combined until a uniform all ratings possible in one
Contractors direct from Nullifire (see
colour is obtained. application
back of leaflet for address and telephone
details).
Application • Fire rating up to 120 minutes
• Keep all product containers closed tested to BS476 and EN13381:
Usage Guidelines when not in use. Parts 6 & 8
Protective Equipment
• Part B is moisture sensitive and should • Designed for on-site use
remain tightly closed before use.
Use in well ventilated conditions and
• The product is self-priming onto
ensure all recommended protective
correctly prepared steelwork.
equipment is worn during handling
Damaged primer does not need to be ETA 14/0079 APPROVAL N° CF5144
& use of this product. For full
repaired in C1 or C2 environments.
recommendation, refer to safety data
• The product should be spray applied
sheet.
at close proximity, approximately
600 mm from the surface, to avoid
Surface Preparation & Priming
dusting and promote good surface
• No primer required for C1 or C2 coalescence.
environments.
• Use of a wet film gauge is essential.
SC902
Intumescent Steel Coating
Topseal Requirements
Once DFT’s have been achieved as specified, TS134 Top Seals can be applied. Ensure the SC902 is completely cured before
applying top seal.
ETAG018: Part 2 Condition Description of Environment Example Approved Topseals
Exposure to rain
Fully external steelwork
X: Exposed Exposure to UV Consult ETA or Nullifire
Exposed perimeter steel
(also qualifies for Y & Z) Uncontrolled humidity Technical Department
Open construction site
Uncontrolled temperature
Uncontrolled humidity
Car park
Y: Semi-exposed Uncontrolled temperature Not required
Undercrofts
(also qualifies for Z) No exposure to rain (consider other factors)
Areas under a canopy
Limited exposure to UV
Z1: Humid internal Humidity over 85% RH Plant rooms, Basements, Not required
(also qualifies for Z2) Temperature above 0°C Warehouse and production (consider other factors)
Humidity below 85% RH Office, Hospitals, Schools, Not required
Z2: Dry internal
Temperature above 0°C Airports Decorative only