Professional Documents
Culture Documents
ELSCO - Catalogo Ruedas Model B PDF
ELSCO - Catalogo Ruedas Model B PDF
ELSCO - Catalogo Ruedas Model B PDF
Si
He
W
De
Sh
M
Fo
Bo
Ro
Th
Ne
Po
Po
Di
Be
Ru
PA
No
Top
Top
■N
MODEL B
■P
El
M O D E R A T E S P E E D R O L L E R G U I D E S
THE INDUSTRY STANDARD.
HE MODEL B ROLLER GUIDE OFFERS EXCEPTIONAL PERFORMANCE
■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■
T IN A COMPACT, EASY-TO-INSTALL PACKAGE.
■■■■■■■■■■
■■■■■■■■■■
MODEL B OUR MOST POPULAR ROLLER GUIDE.
■■■
■■■
1
A typical installation:
Passenger Elevator Cabin guides for
Low- to Mid-Rise Traction Elevator.
Speed: 350 fpm (1,75 m/s).
FEATURES OF THE MODEL B GUIDE: Capacity: 2,500 lbs. (1.100 kg).
5
See inside for mounting instructions. Many factors must be considered when
making a guide selection. Please call us to
M
discuss your specific application.
410.363.9020
info@elscoguides.com M O D E
Installation Instructions
Model B
Model B
Mounting Template
ELSCO Model B elevator roller guides are ELSCO roller guides are carefully assembled,
designed with adjustment features that inspected, and packed to arrive in perfect
provide superior riding characteristics. The condition. When your shipment arrives, inspect
installer can easily adjust ELSCO guides to it carefully for damage and, if appropriate,
compensate for adverse operating conditions immediately file a claim with the carrier. For
and to minimize noise, bumps and vibration. best results, read all instructions thoroughly
For optimum performance and longer roller before proceeding with the installation.
wheel life, we recommend that elevator rails
be properly aligned and cleaned, and the car
balanced before operation.
SIDE ARM
ADJUSTING
NUTS
3 in
(76mm
FACE ARM
FACE ARM ADJUSTING NUT
ADJUSTING NUT
1 2 3 4 5
The Model B Guide comes completely Position guide base over mounting holes or Securely tighten the mounting bolts and/or Be sure that guides are aligned properly Improper alignment. To adjust face roller wheel pressure, tighten
assembled. Note: If adjustable stops have studs. Install mounting hardware (not nuts. At this point, install the remaining roller (as shown) before making any further face arm adjusting nut until the wheel is
been ordered, they will be installed on the included). Make certain that the center of guides on top and/or beneath the elevator. adjustments. compressed 1/32" to 1/16" (1 to 2mm). This
guide. the front mounting slots are located two represents 25 to 50 lbs. (12 to 25kg) of
inches (51mm) back from the face of the rail wheel pressure. Note: If guides are
(refer to mounting template). equipped with polyurethane wheels, refer
to step 11 for allowable wheel pressures.
SQUARE HEAD
SET SCREW
10
GAP 11 12
LARGE FLAT
WASHER ELSCO’s polyurethane roller wheels are a After all adjustments have been made, ride
SIDE ARM ADJUSTING NUT hard (95 Shore A durometer) polymer elevator in both the up and down direction
6 7 8 9
material intended for use on lower speed at inspection speed to check hoistway clear-
When properly adjusted, it will be possible Adjust side roller wheel pressure. Turn the When properly adjusted, it will be possible To adjust float, turn the square head set elevators when the roller wheel pressures ances. Check to be sure that all mounting
to skid the face roller wheel by hand with side arm adjusting nuts until side arm wheels to skid the side arm roller wheels by hand screw to increase or decrease the gap exceed those specified for neoprene compo- bolts and/or nuts are securely tightened.
moderate effort. Be certain that the face roller are compressed 1/32" to 1/16" (1 to 2mm), with moderate effort. Note: If guides are between the large flat washer and the head sition wheels (25 to 50 lbs., or 12 to 25kg.) Make several more runs at operating speed,
wheel pressures are equal for each guide. and the face arm wheels are tracking in the equipped with polyurethane wheels, refer of the square head set screw. Note: The then recheck float (if applicable), tracking
center of rail. This represents approximately to step 11 for allowable wheel pressures. amount of float will be approximately twice While polyurethane roller wheels can operate and roller wheel pressures before returning
25 to 50 lbs. (12 to 25kg) of wheel pressure the gap measured (e.g. 1/16" gap = 1/8" float, at pressures up to 300 lbs. (140kg.) per elevator to service.
on each side arm wheel. If guides are equipped with adjustable and 2mm gap = 4mm float). wheel, it is advisable to keep static pressure
stops, refer to steps 9 and 10. as low as possible to prevent flat spots from
Caution: Adjustable stops may shift forming while the elevator is sitting. Flat spots
during shipment. Be certain to can adversely affect ride quality by causing a
position adjustable stops correctly rough and/or noisy ride. At higher pressures,
(as shown in step 9 diagram). it may not be possible to skid the roller
wheels by hand.
TEM PLATE S HOWN ACTUAL S IZ E
Model B
Mounting Template
11/16 in
(17mm)
1 1/16 in
(27mm)
2 3/4 in
(70mm) 7 1/2 in
(181mm)
5 1/2 in FROM FACE
(140mm) OF RAIL
3 in
(76mm)
9 1/4 in
(235mm)
MAXIMUM
OVERALL
DEPTH
2 in
(51mm)
12 3/4 in
(324mm)
MAXIMUM OVERALL WIDTH
ON T-160 (15#) RAIL
Model B
Specifications
SPECIFICATIONS
Notes:
Top Level Assembly for Model B Roller Guide with Std. Neoprene Rollers is EB02100.
Top Level Assembly for Model B Roller Guide with Polyurethane Rollers is EB02114.
■ Neoprene rollers are identical for rail side and face.
■ Polyurethane rollers use different tread widths for rail side and rail face.