Professional Documents
Culture Documents
Fermator Premium Landing Door Lock CE Certificate PDF
Fermator Premium Landing Door Lock CE Certificate PDF
ñ
ffttlrlilils
HvA lltlt/
lr/
Date of issue 21-07-2016 ing. J.L. van Vliet Ce n decision by
Managing Director
Valid until 21-07-2021
Liftinstituut B.V. Buikslotermeerplein 381 ' P.O. BOX 36027 1020 MA Amsterdam Netherlands ' www.liftinstituut.nl
' Registered at the KvK under number 34157363 '
F23-02-16-v12.A
LIFTINSTITUUT
1. General s cations
Name and address manufacturers Tecnolama, S.A.
Ctra. Constantí km.3
43206 Reus, Spain
Tecnidoors S.p.A.
Via M. Ferrari 5 l7
28012 Cressa (Novara)
P. IVA: lT 02184530026, ltaly
2. Descri NS com
The door locking device Premium consist of two parts, the locking housing and the
locking hook. The door locking device can be used on sliding landing doors. These
are 1,2,3,4 panel side opening automatic horizontal sliding landing doors (11,T2,
T3, T4 ) and 2,4,6,8 panel centre parting automatic horizontal sliding landing doors (
c2, c4, c6, c8 ).
The locking takes place by a hook mounted on the door panel. The housing is
mounted on the door rail. Also is it possible to open the lock by means of a triangular
key according to the requirements of the mentioned standards'
The Premium lock can have a reduced locking beak. ln that case the locking force is
guaranteed by adding 2 countenrueight plates at the other end of the beak. ( See
Annex 1b and 1d ).
The Premium lock and the Premium lock with reduced locking beak can also be
supplied with an lP54 safety contact. ( See Annex 1c and 1d )'
CONTACT #1
Manufacturer Suns
Contact type EDC 61 + DCA F3
U"/1" 230VAC/1 AAC or 200 VDC/ 1 ADC
CONTACT #2
Manufacturer STEM
Contact type N520HD + M125 + NC80 control unit
U"/1" 24VDCI0.5ADC
Registered by the Dutch Chamber of Commerce nr. 34157363, General terms of suppty of Liftinstituut g,V, are registered at the Duth Chamber of Commerce, under number 34157363.
LIFTINSTITUUT
The tests which are performed are as stated in annex F1 of the EN 81-112 and clause
5.2 of EN81-50. These tests have been performed by the manufacturer at their test
location in the Tecnolama premises Reus, Spain.
Some tests are repeated with Liftinstituut present, in order to validate the correctness
of testing and test equipment.
The electrical safety contacts that can be used are also tested at Tecnolama test
location or by the specific manufacturer. Test reports are verified by Liftinstituut.
Some tests are repeated with Liftinstituut present, in order to validate the correctness
of testing and test equipment.
Tecnolama S.A. and the other factories mentioned in chapter 1 of this report have a
certificate of the quality assurance system, according Lifts Direclive 2014133/EU,
annex Vll module H. The scope of this certificate is designing, manufacturing,
performing final inspection and tests of locking devices for landing doors. Therefore
all mentioned factories can perform the tests mentioned in clause 5.2 of EN 81-50
themselves.
4. Results
After the final examination the product and the technical file were found in
accordance with the requirements. The functionaltests passed without remarks
The load tests passed without remarks.
5. Conditions
The door lock shall be used for horizontal power operated sliding landing
doors only.
@L|FT|NST|TUUTB.V. NL16-4OO-1002-075-07 rev.- Date:21-07-2016 Page3of 7
No part of this work may be reproduced in any form by print, photo-print, microfilm or any other means without written permission from Liftinstituut B.V'**'..'*- ""
LITTINSTITUUT B V _ SAFETY AND QUALITY MANAGEMENT
I Buiksl"otermeerpLein 381 | P.0. Box 36027 | Tet. +31 20 - 435 06 06 | www.l.iftinstituut.nl I VAT number: ì
Registered by the Dutch Chamber of Commerce nr. 34157363. Generat terms of suppty of Liftinstituut B.V. are registered at the Duth Chamber of Commerce, under number 34157363.
LIFTINSTITUUT
6. Conclusions
Based upon the results of the EU-type examination Liftinstituut B.V. issues an EU-
type examination certificate.
The EU-type examination certificate is only valid for products which are in conformity
with the same specifications as the type certified product. The certificate is issued
based on the requirements that are valid at the date of issue. ln case of changes of
the product specifications, changes in the requirements or changes in the state of the
art the certificate holder shall request Liftinstituut B.V. to reconsider the validity of the
certificate.
W.Visser
Prod uct Specialist Certification
Liftinstituut B.V.
@LIFTINSTITUUTB.V. NL16-400-1002-075-07 rev.- 21-07-2016 Page 4 of7
No part of this work may be reproduced in any form by pr¡nt, photo-print, microfilm or any means without written permission from Liftinstituut B.V. '.."""'-'**,'"
LIFTINSTITUUT B V _ SAFETY AND 0 UALITY MANAGEMENT
Buikslotermeerptein 381 I P.0. Box 36027 I Tet. +¡t 20 - 435 06 06 www.tiftinstituut.nI VAT number:
NL - 1025 XE Amsterdam I M - rozo MA Amsterdam I Fax +3t 20 - 435 06 26 contact@ [iftinstituut.nl NL 810399441 801
Registered by the Dutch Chamber of Commerce nr. 34157363. Generat terms of suppty of Liftinstituut B.V. are registered at the Duth Chamber of Commerce, under number 34157363.
LIFTINSTITUUT
R PflÛOIIIIS
RvA [ 0[]
Annexes
Annex 1a Premium
.5
\9
i't,
Registered by the Dutch Chamber of Commerce nr. 34157363. Generat terms of suppty of Liftinstituut B.V. are registered at the Duth fhamber of Commerce, under number 34157363.
LIFTINSTITUUT
R frtìfilìil1ìts
fluA ll tltìl
Rivet shafr
I
Annex 1d Premium with reduced locki beak 54 STEM
'j
lã\ -_
cr}*-
Registered by the Dutch Chamber of Commerce nr. 34157363. GeneraI terms of suppty of Liftinstituut B.V. are r€gistered at the Duth Chamber of Comnerce. under numb€r 34157363
R
' LIFTINSTITUUT Pfit]0llIn
fluA I til
¡
I