Professional Documents
Culture Documents
NIT No. 05/Civil/D2/2019-20/01: Indian Institute of Technology Kanpur
NIT No. 05/Civil/D2/2019-20/01: Indian Institute of Technology Kanpur
1.1.1 Lime, moorum, building rubbish Lead - 2 Km 100 cum 89.20 8920.00
1.1.2 Earth Lead - 2 Km ### cum 111.50 2039893.00
Sub-Total 2048813.00
2 EARTH WORK
2.1 Earth work in excavation by mechanical means (Hydraulic
excavator)/manual means over areas (exceeding 30 cm in depth,
1.5 m in width as well as 10 sqm on plan) including getting out
and disposal of excavated earth lead upto 50 m and lift upto 1.5
m, as directed by Engineer-in-charge.
Page 1 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
2.8 Extra for every additional lift of 1.5 m or part thereof in
excavation / banking excavated or stacked materials.
2.8.1 All kinds of soil 2950 cum 51.75 152663.00
2.9 Supplying and filling in plinth with sand under floors, including
watering, ramming, consolidating and dressing complete.
500 cum 917.75 458875.00
2.1 Surface dressing of the ground including removing vegetation
and in- equalities not exceeding 15 cm deep and disposal of
rubbish, lead up to 50 m and lift up to 1.5 m.
"
Page 2 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
3.5 Providing & applying a coat of residual petroleum bitumen of
grade of VG-10 of approved quality using 1.7kg per square metre
on damp proof course after cleaning the surface with brushes
and finally with a piece of cloth lightly soaked in kerosene oil.
150 sqm 91.90 13785.00
3.6 Making plinth protection 50mm thick of cement concrete 1:3:6
(1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size) over 75mm thick bed of dry brick ballast 40 mm
nominal size, well rammed and consolidated and grouted with
fine sand, including necessary excavation, levelling & dressing &
finishing the top smooth.
30 sqm 450.35 13511.00
3.7 Providing and laying PCC 5:10 ( 5 coarse sand : 10 graded brick
aggregate 40 mm nominal size ) for filling in sunken areas at all
floor levels. 300 Cum 3116.00 934800.00
3.8 Extra for Providing & laying Cement concrete above Plinth level
to terrace level or at all floor level. 700 Cum 561.22 392854.00
Sub-Total 11788345.00
4 REINFORCED CEMENT CONCRETE
4.1 Reinforced cement concrete work in walls (any thickness),
including attached pilasters, buttresses, plinth and string courses,
fillets, columns, pillars, piers, abutments, posts and struts etc.
above plinth level up to floor five level, excluding cost of
centering, shuttering, finishing and reinforcement :
Page 3 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
4.4 Extra for additional height in centering, shuttering where ever
required with adequate bracing, propping etc., including cost of
de-shuttering and decentering at all levels, over a height of 3.5
m, for every additional height of 1 metre or part thereof (Plan
area to be measured).
4.4.1 Suspended floors, roofs, landing, beams and balconies (Plan area
to be measured)
### sqm 171.50 1715000.00
4.5 Steel reinforcement for R.C.C. work including straightening,
cutting, bending, placing in position and binding all complete
4.5.1 Thermo-Mechanically
upto plinth level. Treated bars of grade Fe-500D or more. ### Kg 56.60 31979000.00
4.6 Steel reinforcement for R.C.C. work including straightening,
cutting, bending, placing in position and binding all complete
4.6.1 Thermo-Mechanically
above plinth level. Treated bars of grade Fe-500 D or more. ### Kg 56.60 61411000.00
4.7 Add for plaster drip course/ groove in plastered surface or
moulding to R.C.C. projections. 5000 metre 34.15 170750.00
4.8 Providing and laying in position machine batched and machine
mixed design mix M-25 grade cement concrete for reinforced
cement concrete work, using cement content as per approved
design mix, including pumping of concrete to site of laying but
excluding the cost of centering, shuttering, finishing and
reinforcement, including admixtures in recommended
4.8.1 All works uptoasplinth
proportions per level
IS: 9103 to accelerate, retard setting of 330 cum 6446.45 2127329.00
4.8.2 concrete, improve
All works above workability
plinth level uptowithout impairing strength and 3000
floor V level cum 7250.05 21750150.00
durability as per direction of Engineer-in-charge.“(Note :-
4.9 Extra for content
Cement providing considered
richer mixesin atthis
all floor
item levels.
is @Note:-
330
Excess/less cementless
kg/cum.“Excess/ overcement
the specified
used ascement
per content
design used
mix is
is
payable /recoverableseparately).
payable/recoverable separately.
4.9.1 Providing M-30 grade concrete instead of M-25 grade BMC/
RMC. (Note:- Cement content considered in M-30 is @ 340 kg/
cum) 50 cum 69.50 3475.00
4.1 Add for using extra cement in the items of design mix over and quinta
above the specified cement content therein. 3500 l 672.75 2354625.00
4.11 Providing and laying in position ready mixed M-25 grade
concrete for reinforced cement concrete work, using cement
content as per approved design mix, manufactured in fully
automatic batching plant and transported to site of work in
transit mixer for all leads, having continuous agitated mixer,
manufactured as per mix design of specified grade for reinforced
cement concrete work, including pumping of R.M.C. from transit
mixer to site of laying , excluding the cost of centering,
shuttering finishing and reinforcement, including cost of
admixtures in recommended proportions as per IS : 9103 to
accelerate/ retard setting of concrete,improve workability
without impairing strength and durability as per direction of the
Engineer-in-charge. (Note :- Cement content considered in this
item is @ 330 kg/cum. Excess/less cement used as per design
mix is payable/recoverable separately)
4.11.1 All works upto plinth level 2700 cum 6713.60 18126720.00
4.11.2 All works above plinth level upto floor V level 4600 cum 7517.20 34579120.00
4.12 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each
four floors or part thereof. 2900 cum 232.30 673670.00
4.13 "Providing and fixing dash fastners of size 12 mm x 100 mm for
railing of stairs, corridors and parapet i/c drilling fixing and
necessary welding etc. complete.
1800 Each 55.20 99360.00
4.14 ""Providing and fixing dash fastners of size 8 mm x 70 mm for
railing of stairs, corridors and parapet i/c drilling fixing and
necessary welding etc. complete. 200 Each 42.85 8570.00
"
4.15 "Centering and shuttering i/c strutting, propping etc. and
removal of form work for mullions upto floor Eight levels etc.
complete.
1600 Sqm 1198.00 1916800.00
4.16 "Injection grouting in the RCC walls of overhead tank i/c providing
and fixing G.I nozzles of required size and cement and testing
etc. all complete.
100 Each 336.00 33600.00
4.17 Extra for Providing and laying RMC/BMC/RCC Work at below
3.00 meter from plinth level or part thereof. 20 Cum 165.41 3308.00
4.18 Extra for using removable tie bolt and pvc pipe in walls/columns 100 Each 50.00 5000.00
shuttering due to larger size.
Page 4 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
4.19 Providing, making & fixing of MS/GI Pipe sleeved with flange
( Dia 40mm to 160mm ) in R.C.C. Walls of tanks at desired level
as per the directions of Engineer-in-charge. 50 Each 750.00 37500.00
4.2 GRC JALI 940 Sqm 7140.00 6711600.00
Providing and fixing Glass Reinforced Concrete Cum/
4.21 Carriage of concrete
(G.R.C) Screens by transit
in approved mixer
size, beyond
pattern, 10 KM lead.
design, ### Km 26.71 742538.00
thickness
Sub-Total and color. The Screens should be made 215013782.00
from ‘53 grade’ White Portland Cement
5 BRICK WORK by ‘JK Cement’ or equivalent,
manufactured
Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber
5.1 Brick work withbycommon
manufactured burnt or
‘Saint Gobain’ clay F.P.S. (non modular) bricks
equivalent,
of LocalPlasticizers
Super 1st class inmanufactured
foundation andbyplinth‘BASF’in: or
equivalent, Polymers manufactured by ‘BASF’ or
5.1.1 Cement
equivalent mortar 1:4 resistant
and U.V (1 cementSynthetic
: 4 coarse sand)
inorganic 5 cum 4970.30 24852.00
5.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 250 cum 4751.65 1187913.00
pigments should be used for pigmentation
5.2 Brick work withbycommon
manufactured ‘BAYFERROXburnt (Germany)’
clay F.P.S. (non
or modular) bricks
of Local 1st The
equivalent. classmaterial
in superstructure
casting shouldabove
takeplinth
placelevel up to floor
V
in level in all Rubber
Synthetic shapes and/ FRPsizes in : manufactured by
Mould
‘Reckli’ or equivalent. The fixing of Screens should
5.2.1 Cement
be mortari.e.
‘Dry fixing’ 1:6to(1becement : 6 coarse
done with sand)
Stainless Steel 4000 cum 5582.85 22331400.00
5.3 (SS
Extra – 304) ‘L’ shaped
for brick work /Clamps, dash
AAC block fasteners
masonry andbrick masonry in 1200 cum
/ Tile 205.45 246540.00
pins. etc. complete
superstructure aboveas per directed byfor
Engineer-in-
5.4 Half brick masonry
Charge. withfloor V level,
common burnt eachF.P.S.
clay four (non
floorsmodular)
or part
thereof by mechanical means.
bricks of Local 1st class in foundations and plinth in :
5.4.1 cement mortar 1:4 (1 cement : 4 coarse sand) 50 sqm 593.50 29675.00
5.5 Half brick masonry with common burnt clay F.P.S. (non modular)
bricks of Local 1st class in superstructure above plinth level up to
floor V level.
5.5.1 Cement mortar 1:4 (1 cement :4 coarse sand) ### sqm 684.20 7868300.00
5.6 Extra for half brick masonry in superstructure, above floor V level
for every four floors or part thereof by mechanical means.
5000 sqm 18.20 91000.00
5.7 Brick edging 7cm wide 11.4 cm deep to plinth protection with
common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 including grouting with cement mortar 1:4 (1
cement : 4 fine sand).
30 metre 39.20 1176.00
5.8 Providing and laying autoclaved aerated cement blocks masonry
with 150mm/230mm/300 mm thick AAC blocks in super
structure above plinth level up to floor V level with RCC band at
sill level and lintel level with approved block laying polymer
modified adhesive mortar all complete as per direction of
Engineer- in-Charge. (The payment of RCC band and
reinforcement shall be made for seperately).
20 cum 5687.10 113742.00
5.9 Providing and laying insulation with 50mm thick thermocol sheet
of density 24Kg/cum with approved adhesive or with nails and
washer to hold the sheet with necessary weep and vent holes in
cavity walls
100 Sqm 318.00 31800.00
Sub-Total 31926398.00
6 MARBLE AND GRANITE WORK
6.1 Providing and fixing 18 mm thick gang saw cut, mirror polished,
premoulded and prepolished, machine cut for kitchen platforms,
vanity counters, window sills,floor,skirting, facias and similar
locations of required size, approved shade, colour and texture
laid over 20 mm thick base cement mortar 1:4 (1 cement : 4
coarse sand), joints treated with white cement, mixed with
matching pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high gloss finish etc.
complete at all levels.
6.1.1 Granite of any colour and shade
6.1.1.1 Area of slab upto 0.50 sqm 100 sqm 3351.95 335195.00
6.1.1.2 Area of slab over 0.50 sqm 1150 sqm 3113.30 3580295.00
6.2 Providing edge moulding to 18 mm thick marble stone counters,
Vanities etc., including machine polishing to edge to give high
gloss finish etc. complete as per design approved by Engineer-in-
Charge.
Page 5 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
6.3 Extra for fixing marble /granite stone, over and above
corresponding basic item, in facia and drops of width upto 150
mm with epoxy resin based adhesive, including cleaning etc.
complete.
150 metre 266.25 39938.00
6.4 Extra for providing opening of required size & shape for wash
basin/ kitchen sink in kitchen platform, vanity counter and
similar location in marble/ Granite/ stone work, including
necessary holes for pillar taps etc. including moulding, rubbing
and polishing of cut edges etc. complete.
336 each 427.95 143791.00
6.5 Mirror polishing on marble work/Granite work/stone work
where ever required to give high gloss finish complete.
7500 sqm 231.50 1736250.00
6.6 Providing and fixing cramps of required size & shape in RCC/ CC /
Brick masonry backing with cement mortar 1:2 ( 1 cement : 2
coarse sand), including drilling necessary hole in stones and
embedding the cramp in the hole (fastener to be paid
separately).
6.7.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown,
Cat Eye or equivalent. 5 sqm 2937.70 14689.00
6.8 Providing and fixing of full bodied vitrified tiles Stepping stone
( Full body anti - skid,for Tread or Riser single piece length
1200mm, 15 to18 mm thick, full bull nosed, with upper top or
bottom rib ) in Tread, skirting, risers of steps and dados,landing
area etc over 12 mm to 20mm thick bed of cement mortar 1:3 (1
cement : 3 coarse sand) and jointing with grey cement slurry @
3.3kg per sqm, including pointing in white cement mixed with
pigment of matching shade all complete.
7.2.1 35 mm thick including ISI marked Stainless Steel butt hinges with
necessary screws 2400 sqm 1559.75 3743400.00
7.2.2 25 mm thick (for cupboard) including ISI marked nickel plated
bright finished M.S. piano hinges with necessary screws
1300 sqm 1501.90 1952470.00
7.3 Extra for providing lipping with 2nd class teak wood battens 25
mm minimum depth on all edges of flush door shutters (over all
area of door shutter to be measured). 50 sqm 365.85 18293.00
7.4 Extra for cutting rebate in flush door shutters (Total area of the
shutter to be measured). 1770 sqm 127.75 226118.00
7.5 Providing and fixing teak wood lipping of size 25x3 mm in
pelmet. 10 metre 41.10 411.00
Page 6 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
7.6 Providing and fixing M.S. grills of required pattern in frames of
windows etc. with M.S. flats, square or round bars etc. including
priming coat with approved steel primer all complete.
Page 7 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
7.18 Providing and fixing factory made panel PVC door shutter
consisting of frame made out of M.S. tubes of 19 gauge thickness
and size of 19 mm x 19 mm for styles and 15x15 mm for top &
bottom rails. M.S. frame shall have a coat of steel primers of
approved make and manufacture. M.S. frame covered with 5
mm thick heat moulded PVC 'C' channel of size 30 mm thickness,
70 mm width out of which 50 mm shall be flat and 20 mm shall
be tapered in 45 degree angle on both side forming styles and 5
mm thick, 95 mm wide PVC sheet out of which 75 mm shall be
flat and 20 mm shall be tapered in 45 degree on the inner side to
form top and bottom rail and 115 mm wide PVC sheet out of
which 75 mm shall be flat and 20 mm shall be tapered on both
sides to form lock rail. Top, bottom and lock rails shall be
provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm
wide cross PVC sheet be provided as gap insert for top rail &
bottom rail, paneling of 5 mm thick both side PVC sheet to be
fitted in the M.S. frame welded/ sealed to the styles & rails with
7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on
inner side, and joined together with solvent cement adhesive. An
additional 5 mm thick PVC strip of 20 mm width is to be stuck on
the interior side of the 'C' Channel using PVC solvent adhesive
etc. complete as per direction of Engineer-in-charge,
manufacturer's specification & drawing.
7.18.1 30 mm thick pre laminated PVC door shutters 710 sqm 3232.70 2295217.00
7.19 Providing and fixing wire gauge shutters using stainless steel
grade 304 wire gauge with wire of dia 0.5 mm and average width
of aperture 1.4 mm in both directions for doors, windows and
clerestory windows with necessary screws :
Page 8 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
7.23 Providing and fixing glazing in fire resistant door shutters, fixed
panels & partitions etc., with G.I. beading made out of 1.6 mm
thick G.I. sheet (zinc coating not less than 120 gm/m2) of size 20
x 33 mm screwed with M4 x 38 mm 55 screws at distance 75 mm
from the edges and 150 mm c/c , including applying a coat of
approved fire resistant primer/powder coating of not less than
30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm
size etc complete in all respect as per NBC 2016, IS 16231 (Part
3):2016 and as per direction of Engineer-in-charge with glass of
required thickness having 60 minutes of fire resistance both
integrity & radiation control (EW60) and minimum 20 min of
insulation (E120). The manufacturer have to give test
report/certification of fire glass and the glass should have the
stamp showing the value of E, EW & El. The glass shall be
tested in approved NABL accredited lab or by any other
accreditation body which operates in accordance with ISO/EEC
17011 and accredits labs as per ISO/IEC 17025 for testing and
calibration scopes shall be eligible. The maximum glazing size
shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.
Page 9 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
7.35 Construction of modular kitchen ( Providing and Fixing all
complete ) as per approved Drawing and design with;(Grade of
steel - 304).
1. Perforated Cutlery (Everyday/Inox or Equivalent ) – 01 nos
( 520*485*100 mm).
2. Drawer Basket (Everyday/Inox or Equivalent ) -05 nos
(520*485*100 mm ).
3. Plates Basket(Everyday/Inox or Equivalent ) – 01 nos
(520*485*140 mm )
4. Bottle P. O. 2 S (Everyday/Inox or Equivalent ) – 01nos
(150*485*420 mm ).
5. Meta Drawer (Hettich/Haffle or equivalent ) – 01nos
(520*500*86 mm ).
6. Grain Trolly Basket with porter(Everyday/Inox or Equivalent )
-01 (520*485*190 mm).
7. Rack (Everyday/Inox or Equivalent )– 01nos (100*485*420 mm
).
8. Glass & Plate Rack including Drip Tray and Glass Shutters (A&A
Modular System/Dynasty or equivalent ) – 01 (862*230*25/65
mm).
9. Corner Carrousel unit(Everyday/Inox or Equivalent ) – 01 nos
(700mm dia).
With required Auto Closing Concealed Hinges (Hettich/Haffle or
equivalent ), Auto Closing Concealed Special Corner
Hinges(Hettich/Haffle or equivalent ), Handles(Hettich/Haffle or
equivalent ), Hardware (Screws counter sunk, Connect Fastners,
Tags), Solid Shutters with Mica lamination(A&A Modular
System/Dynasty or equivalent ), Full extension ball bearing
sliding telescopic(Hettich/Haffle or equivalent ) and Marble
partition as per site requirement all Complete .
One
112 Job 120415.00 13486480.00
7.36 Providing and fixing Single point locking handles "PULSE"
(aluminium & zamak) ( PL205H / Model) of LGF Sysmac ( I ) Pvt.
Ltd. or equivalent make as approved powder coated to required
colour or shade including the cost of screw and other incidental
charges complete as per manufacturers specification.
8.2.1 Using M.S. angles 40x40x6 mm for diagonal braces 33 sqm 2870.25 94718.00
Page 10 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
8.3 Providing and fixing T-iron frames for doors, windows and
ventilators of mild steel Tee-sections, joints mitred and welded,
including fixing of necessary butt hinges and screws and applying
a priming coat of approved steel primer.
8.4.1 Profile B
8.4.1.1 Fixing with adjustable lugs with split end tail to each jamb 50 metre 340.35 17018.00
8.5 Steel work welded in built up sections/ framed work, including
cutting, hoisting, fixing in position and applying a priming coat of
approved steel primer using structural steel etc. as required.
9.1.1 40 mm thick with 20 mm nominal size stone aggregate 150 sqm 362.60 54390.00
9.2 Cement concrete pavement with 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size), including
finishing complete. 5 cum 5804.35 29022.00
9.3 Providing and fixing glass strips in joints of terrazo/ cement
concrete floors.
9.3.1 40 mm wide and 4 mm thick 700 metre 52.50 36750.00
9.4 Kota stone slab flooring over 20 mm (average) thick base laid
over and jointed with grey cement slurry mixed with pigment to
match the shade of the slab, including rubbing and polishing
complete with base of cement mortar 1 : 4 (1 cement : 4 coarse
sand) :
Page 11 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
9.5 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and
pillars laid on 12 mm (average) thick cement mortar 1:3 (1
cement: 3 coarse sand) and jointed with grey cement slurry
mixed with pigment to match the shade of the slabs, including
rubbing and polishing complete.
1000 sqm 1238.20 1238200.00
9.6 Providing and fixing Ist quality ceramic glazed wall tiles
conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by
Engineer-in-Charge, in skirting, risers of steps and dados, over 12
mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)
and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade
complete.
Page 12 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
9.14 Extra for Tile work for on walls of height more than 2.10 mtr
from floor level for every additional height of 3.00 mtr or part
thereof 40 Sqm 88.79 3552.00
9.15 Extra for making steps of stair antiskid by making band of 3 nos.
grooves, 3 mm wide along kota stone (Clear Tread length will be
measured). 10 Metre 273.98 2740.00
9.16 Extra for Providing & fixing machine-cut & machined polished
Stone in sill, copings,parapet top, window sill, planter top and
such other locations, laid on 20 mm (average) thick cement
mortar 1:4 (1cement:4coarse sand) and jointed with grey cement
slurry mixed with pigment to match the shades of the slabs,
including rubbing and polishing complete instead of Kota stone
slabs 20 mm thick in risers of steps, skirting, dado and pillars laid
on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse
sand) and jointed with grey cement slurry mixed with pigment to
match the shade of the slabs, including rubbing and polishing
complete.
10.4.1 Coupler
10.4.1.1 75 mm 112 each 64.95 7274.00
10.4.1.2 110 mm 5 each 102.65 513.00
10.4.2 Single tee with door
10.4.2.1 110x110x110 mm 5 each 181.55 908.00
10.4.3 Single tee without door
10.4.3.1 75x75x75 mm 336 each 105.25 35364.00
10.4.4 Bend 87.5°
10.4.4.1 110 mm bend 5 each 113.10 566.00
10.4.5 Shoe (Plain)
10.4.5.1 75 mm Shoe 32 each 66.10 2115.00
10.4.5.2 110 mm Shoe 2 each 98.00 196.00
Page 13 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
10.5 Providing and fixing unplasticised -PVC pipe clips of approved
design to unplasticised - PVC rain water pipes by means of
50x50x50 mm hard wood plugs, screwed with M.S. screws of
required length, including cutting brick work and fixing in cement
mortar 1:4 (1 cement : 4 coarse sand) and making good the wall
etc. complete.
11.13.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over
and including priming coat of exterior primer applied @
2.20kg/10 sqm ### sqm 150.65 3916900.00
11.14 Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade:
11.14.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over
and including priming coat of exterior primer applied @ 2.20
kg/10 sqm) 6000 sqm 96.80 580800.00
11.15 Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade :
11.15.1 Two or more coats on new work 3010 sqm 78.40 235984.00
11.16 Painting with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade :
Page 14 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
11.16.1 Two or more coats on new work over an under coat of suitable
shade with ordinary paint of approved brand and manufacture per
### letter
sqm 112.30 1123000.00
11.17 Lettering with black Japan paint of approved brand and per
manufacture cm
8000 height 2.70 21600.00
11.18 Providing and applying white cement based putty of average
thickness 1 mm, of approved brand and manufacturer, over the
plastered wall surface to prepare the surface even and smooth
complete.
### sqm 87.35 5686485.00
11.19 Providing and fixing 65 mm dia GI spout 400 mm long at all levels
and locations including cutting & making good the walls and
painting the spout and all incidentals complete.
10 Each 371.00 3710.00
11.2 "Providing & Fixing Chicken Wire Mesh on Joints of RCC & Brick
Work Before Plastering Work
" 100 Sqm 88.00 8800.00
11.21 Extra for additional height in ceiling plaster at all level over a
height of 5.00 mtr for every additional height 1.00 mtr or part
therof for ceiling, soffit etc. 150 Sqm 183.33 27500.00
11.22 Extra for plaster internal wall of height more than 5.00 mtr for
every additional height 3.00 mtr or part therof. 150 Sqm 40.98 6147.00
Sub-Total 35131509.00
12 ROAD WORK
12.1 Preparation and consolidation of sub grade with power road
roller of 8 to 12 tonne capacity after excavating earth to an
average of 22.5 cm depth, dressing to camber and consolidating
with road roller including making good the undulations etc. and
re-rolling the sub grade and disposal of surplus earth with lead
upto 50 metres.
2800 sqm 90.10 252280.00
12.2 Extra for compaction of earth work in embankment under
optimum moisture conditions to give at least 95% of the
maximum dry density (proctor density). 2800 cum 10.70 29960.00
12.3 Supplying and stacking at site.
12.3.1 53 mm to 22.4 mm size stone aggregate 280 cum 1542.25 431830.00
12.3.2 Stone screening 11.2 mm nominal size (Type B) 40 cum 1462.05 58482.00
12.4 Supplying, stacking and Spreading 6 mm thick red bajri, watering
and rolling complete including preparation of the surface and
rolling.
12.4.1 With road roller/ hand roller 2800 sqm 15.55 43540.00
12.5 Brick edging in full brick width and half brick depth including
excavation, refilling and disposal of surplus earth lead upto 50
metres.
12.5.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 20 metre 127.60 2552.00
12.6 Providing and laying at or near ground level factory made kerb
stone of M-25 grade cement concrete in position to the required
line, level and curvature, jointed with cement mortar 1:3 (1
cement: 3 coarse sand), including making joints with or without
grooves (thickness of joints except at sharp curve shall not to
more than 5mm), including making drainage opening wherever
required complete etc. as per direction of Engineer-in-charge
(length of finished kerb edging shall be measured for payment).
(Precast C.C. kerb stone shall be approved by Engineer-in-
charge).
Page 15 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
12.8 Providing and laying 70 mm thick factory made RCC grass Grid
paver blocks of M30 grade made by block making machine with
strong vibratory compaction, of size 600mm x 400mm and of
approved design , laid over and including 50mm thick compacted
bed of fine sand, filling the joints and holes with mix 50%
available Earth and 50% fine sand etc. all complete as per the
direction of Engineer-in-charge.
2350 Sqm 1565.00 3677750.00
12.9 Supplying and application and filling of groove in dummy joints
of RCC floor size of 10 X 22 mm by polysulphide make of Dr fixit
pidiseal P5 42P complete. 1450 Metre 168.40 244180.00
Sub-Total 7590122.00
13 SANITARY INSTALLATIONS
13.1 Providing and fixing water closet squatting pan (Indian type W.C.
pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level
white P.V.C. flushing cistern, including flush pipe, with manually
controlled device (handle lever) conforming to IS : 7231, with all
fittings and fixtures complete, including cutting and making good
the walls and floors wherever required:
13.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440
mm with integral type foot rests 3 each 3494.20 10483.00
13.2 Providing and fixing white vitreous china pedestal type water
closet (European type W.C. pan) with seat and lid, 10 litre low
level white P.V.C. flushing cistern, including flush pipe, with
manually controlled device (handle lever), conforming to IS :
7231, with all fittings and fixtures complete, including cutting and
making good the walls and floors wherever required :
13.2.1 W.C. pan with ISI marked white solid plastic seat and lid 224 each 3418.70 765789.00
13.3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P.
brass pillar taps, 32 mm C.P. brass waste of standard pattern,
including painting of fittings and brackets, cutting and making
good the walls wherever require:
13.3.1 White Vitreous China Flat back wash basin size 550x 400 mm
with single 15 mm C.P. brass pillar tap 3 each 1817.35 5452.00
13.4 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink
as per IS: 13983 with C.I. brackets and stainless steel plug 40
mm, including painting of fittings and brackets, cutting and
making good the walls wherever required :
Page 16 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
13.11.1 C.P. brass 224 each 385.35 86318.00
13.12 Providing and fixing soil, waste and vent pipes :
13.12.1 100 mm dia
13.12.1.1 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:
3989 5500 metre 921.65 5069075.00
13.12.2 75 mm diameter :
13.12.2.1 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 1500 metre 794.55 1191825.00
13.13 Providing and fixing M.S. holder-bat clamps of approved design
to Sand Cast iron/cast iron (spun) pipe embedded in and
including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size), including cost of cutting holes and making good
the walls etc. :
Page 17 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
13.21.2 75 mm 2000 each 263.60 527200.00
13.22 Providing and fixing M.S. stays and clamps for sand cast iron/
centrifugally cast (spun) iron pipes of diameter :
13.22.1 100 mm 2400 each 62.00 148800.00
13.22.2 75 mm 2 each 56.55 113.00
13.23 Providing and fixing trap of self cleansing design with screwed
down or hinged grating with or without vent arm complete,
including cost of cutting and making good the walls and floors :
13.26.1 600 mm long towel rail with total length of 645 mm, width 78
mm and effective height of 88 mm, weighing not less than 190
gms. 4 each 422.70 1691.00
13.27 "P/F C.P. brass single hole basin mixer with casted swinging
spout of L&K make ( Model no. 0407 ) or approved equivalent.
"
"15 mm nominal bore
"
224 Each 2195.00 491680.00
13.28 "Providing and fixing 15 mm inlet C.P. brass adjustable shower
with long shower arm (heavy) complete with cp flange of ESSCO (
Model no. CON -491 ) or approved equivalent make.
"
230 Each 754.00 173420.00
13.29 "Providing and Fixing C.P. hand spray (health faucet) with push
button control and flexible hose connection with C.P. hook of
L&K make or approved equivalent complete in all respects.
"
230 Each 1089.00 250470.00
13.3 "Providing & fixing stainless steel grating with or without hole of
an approved make & design for waste pipe including setting in
floor with cement mortar.
"
"125 mm dia weight not less than 100 gms
"
926 Each 46.00 42596.00
13.31 "Providing & fixing C.P. brass twin coat hook of ESSCO ( Model
no. 1161 ) or approved equivalent make fixed on door shutters
with C.P. brass screws etc. complete.
"
Page 18 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
13.33 "Providing and fixing white vitreous china wash basin oval type
550X400mm with MS/CI brackets painted white SE paint, 32mm
CP brass waste, rubber adopter for waste connection complete.
Make: WB:Parryware or equivalent of Hindware or Cera .
"
Page 19 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
14.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, i/c fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement and the cost of
cutting chases and making good the same including testing of
joints complete as per direction of Engineer in Charge. Concealed
work, including cutting chases and making good the walls etc.
Page 20 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
14.12 Providing and laying S&S centrifugally cast (spun) iron pipes
(Class LA) conforming to IS - 1536 :
14.12.1 100 mm dia pipe 200 metre 1078.25 215650.00
14.12.2 150 mm dia pipe 50 metre 1621.60 81080.00
14.13 Providing lead caulked joints to spun iron or C.I. pipes and
specials, including testing of joints but excluding the cost of pig
lead :
14.13.1 100 mm diameter pipe 25 each 224.65 5616.00
14.13.2 150 mm diameter pipe 10 each 337.20 3372.00
14.14 Supplying pig lead at site of work. quinta
2 l 16039.40 32079.00
14.15 Providing and fixing C.I. sluice valves (with cap) complete with
bolts, nuts, rubber insertions etc. (the tail pieces if required will
be paid separately) :
14.15.1 100 mm diameter
14.15.1.1 Class I 2 each 3317.55 6635.00
14.15.2 125 mm diameter
14.15.2.1 Class I 1 each 3596.80 3597.00
14.15.3 18.1.3 150 mm diameter
14.15.3.1 Class I 4 each 4881.25 19525.00
14.15.4 200 mm diameter
14.15.4.1 Class I 1 each 9604.50 9605.00
14.16 Constructing masonry Chamber 30x30x50 cm inside, in brick
work in cement mortar 1:4 (1 cement :4 coarse sand) for stop
cock, with C. I. surface box 100x100 x75 mm (inside) with hinged
cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c
necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5
fine sand : 10 graded stone aggregate 40mm nominal size ) and
inside plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12mm thick, finished with a floating coat of neat cement
complete as per standard design :
Page 21 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
14.19 Painting G.I. pipes and fittings with two coats of anti-corrosive
bitumastic paint of approved quality :
14.19.1 15 mm diameter pipe 10 metre 6.00 60.00
14.19.2 20 mm diameter pipe 10 metre 7.10 71.00
14.19.3 25 mm diameter pipe 10 metre 9.10 91.00
14.19.4 32 mm diameter pipe 10 metre 10.85 109.00
14.19.5 40 mm diameter pipe 10 metre 12.35 124.00
14.19.6 50 mm diameter pipe 50 metre 14.80 740.00
14.19.7 65 mm diameter pipe 20 metre 18.25 365.00
14.19.8 80 mm diameter pipe 20 metre 21.20 424.00
14.2 Providing and filling sand of grading zone V or coarser grade,
allround the G.I. pipes in external work :
14.20.1 50 mm diameter pipe 50 metre 74.95 3748.00
14.20.2 65 mm diameter pipe 20 metre 118.30 2366.00
14.20.3 80 mm diameter pipe 20 metre 121.90 2438.00
14.21 Providing and fixing G.I. Union in G.I. pipe including cutting and
threading the pipe and making long screws etc. complete (New
work) :
14.21.1 15 mm nominal bore 10 each 147.75 1478.00
14.21.2 20 mm nominal bore 20 each 170.95 3419.00
14.21.3 25 mm nominal bore 30 each 205.80 6174.00
14.21.4 32 mm nominal bore 40 each 240.65 9626.00
14.21.5 40 mm nominal bore 50 each 298.75 14938.00
14.21.6 50 mm nominal bore 50 each 384.90 19245.00
14.21.7 65 mm nominal bore 10 each 617.20 6172.00
14.21.8 80 mm nominal bore 2 each 698.50 1397.00
14.22 Providing and fixing C.P. brass bib cock of approved quality
conforming to IS:8931 :
14.22.1 15 mm nominal bore 672 each 371.70 249782.00
14.23 Providing and fixing C.P. brass long body bib cock of approved
quality conforming to IS standards and weighing not less than
690 gms.
14.23.1 15 mm nominal bore 112 each 492.55 55166.00
14.24 Providing and fixing C.P. brass stop cock (concealed) of standard
design and of approved make conforming to IS:8931.
Page 22 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
14.3 Providing and fixing CP brass flange and extension piece as per
requirement.
2400 Each 130.00 312000.00
14.31 "Providing and fixing water metre of approved quality ank make
i/c necessary arrangement etc complete.
20MM dia"
224 Each 2771.00 620704.00
14.32 "Providing and fixing chrome plated copper pipe with brass
union jaguar or approved make :
45 cm length
15 mm nominal bore
" 900 Each 284.00 255600.00
14.33 Providing and fixing CPVC Gate Valve 20 mm dia with all
complete. 226 Each 999.49 225885.00
14.34 Providing and Fixing of C.P. brass sink mixer with long casted
swinging spout of L&K make or equvalent approved brand
15 mm nominal bore
112 Each 2195.00 245840.00
14.35 Providing and Fixing of C.P. brass nozzle cock of L&K or approved
make and design
112 Each 623.00 69776.00
15 mm nominal bore.
14.36 P/F 125x125 mm square SS cockroch trap consisting of 0.45 mm
inner and outer cup and 1 mm thick top grating (jali) with ring to
be fixed inside C.I. P traps with cement concrete (For kitchen and
pantry).
224 Each 372.00 83328.00
Sub-Total 9283460.00
15 DRAINAGE
15.1 Providing, laying and jointing glazed stoneware pipes class SP-1
with stiff mixture of cement mortar in the proportion of 1:1 (1
cement : 1 fine sand) including testing of joints etc. complete :
Page 23 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
15.5 Providing and laying non-pressure NP2 class (light duty) R.C.C.
pipes with collars jointed with stiff mixture of cement mortar in
the proportion of 1:2 (1 cement : 2 fine sand) including testing of
joints etc. complete :
15.6.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with
frame (light duty) 455x610 mm internal dimensions, total weight
of cover and frame to be not less than 38 kg (weight of cover 23
kg and weight of frame 15 kg) :
15.6.1.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 50 each 8634.10 431705.00
15.6.2 Inside size 120x90 cm and 90 cm deep including C.I. cover with
frame (medium duty) 500 mm internal diameter, total weight of
cover and frame to be not less than 116 kg (weight of cover 58
kg and weight of frame 58 kg) :
15.6.2.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 40 each 18422.40 736896.00
15.7 Extra for depth for manholes :
15.7.1 Size 90x80 cm
15.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 65 metre 5718.60 371709.00
15.7.2 Size 120x90 cm
15.7.2.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 20 metre 6850.70 137014.00
15.8 Constructing brick masonry circular type manhole 0.91 m
internal dia at bottom and 0.56m dia at top in cement mortar 1:4
(1 cement : 4 coarse sand), inside cement plaster 12 mm thick
with cement mortar 1:3 (1 cement : 3 coarse sand) finished with
a floating coat of neat cement, foundation concrete 1:3:6 mix (1
cement : 3 coarse sand : 6 graded stone aggregate 40 mm
nominal size), and making necessary channel in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat cement, all
complete as per standard design :
15.8.1 0.91 m deep with SFRC cover and frame (heavy duty, HD- 20
grade designation) 560 mm internal diameter conform- ing to I.S.
12592, total weight of cover and frame to be not less than 182
kg., fixed in cement concrete 1:2:4 (1 ce- ment : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) including centering,
shuttering all complete. (Excavation, foot rests and 12mm thick
cement plaster at the external surface shall be paid for
separately) :
15.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 1 each 8683.75 8684.00
15.9 Extra depth for circular type manhole 0.91m internal dia (at
bottom) beyond 0.91 m to 1.67 m
15.9.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 0.5 metre 4911.80 2456.00
Page 24 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
15.1 Constructing brick masonry circular manhole 1.22 m internal dia
at bottom and 0.56 m dia at top in cement mortar 1:4 (1
cement :4 coarse sand) inside cement plaster 12 mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand) finished with a
floating coat of neat cement foundation concrete 1:3:6 (1
cement : 3 coarse sand : 6 graded stone aggregate 40 mm
nominal size) and making necessary channel in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat cement, all
complete as per standard design :
15.10.1 1.68 m deep with SFRC Cover and frame (heavy duty HD- 20
grade designation) 560 mm internal diameter conform- ing to I.S.
12592, total weight of cover and frame to be not less than 182
kg. fixed in cement concrete 1:2:4 (1 ce- ment : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) including centering,
shuttering all complete. (Excavation, foot rests and 12 mm thick
cement plaster at the external surface shall be paid for
separately) :
15.10.1.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 4 each 16560.80 66243.00
15.11 Extra depth for circular type manhole 1.22 m internal dia (at
bottom) beyond 1.68 m to 2.29 m :
15.11.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 4 metre 6362.65 25451.00
15.12 Providing orange colour safety foot rest of minimum 6 mm thick
plastic encapsulated as per IS : 10910, on 12 mm dia steel bar
conforming to IS: 1786, having minimum cross section as 23
mmx25 mm and over all minimum length 263 mm and width as
165 mm with minimum 112 mm space between protruded legs
having 2 mm tread on top surface by ribbing or chequering
besides necessary and adequate anchoring projections on tail
length on 138 mm as per standard drawing and suitable to with
stand the bend test and chemical resistance test as per
specifications and having manufacture's permanent
identification mark to be visible even after fixing, including fixing
in manholes with 30x20x15 cm cement concrete block 1:3:6 (1
cement : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size) complete as per design.
15.15.1 With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 60 each 4043.10 242586.00
Page 25 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
15.16 Constructing brick masonry chamber for underground C.I.
inspection chamber and bends with bricks in cement mortar 1:4
(1 cement : 4 coarse sand) C.I. cover with frame (light duty)
455x610 mm internal dimensions, total weight of cover with
frame to be not less than 38 kg (weight of cover 23 kg and
weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement :
2 coarse sand : 4 graded stone aggregate 20 mm nominal size),
foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) :
10 graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1 cement : 3
coarse sand), finished smooth with a floating coat of neat
cement on walls and bed concrete etc. complete as per standard
design:
16.2.1 With float glass panes of 5.50 mm thickness 2200 sqm 1003.95 2208690.00
16.3 Extra for applying additional anodic coating AC 25 instead of AC
15 to aluminium extruded sections.
16.3.1 For fixed portion ### kg 11.60 116000.00
16.3.2 For shutters of doors, windows & ventilators ### kg 11.60 203000.00
16.4 Providing and fixing stainless steel (SS 304 grade) adjustable
friction windows stays of approved quality with necessary
stainless steel screws etc. to the side hung windows as per
direction of Engineer- in-charge complete.
Page 26 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
16.5 "Providing and fixing anodized aluminium work for doors,
windows, ventilators and partitions with extruded built-up
standard tubular sections / appropriate Z sections and other
sections of approved make conforming to IS: 733 and IS: 1285,
fixed with rawl plugs and screws or with fixing clips, or with
expansion hold-fasteners including necessary filling up of gaps at
junctions, at top, bottom and sides with required PVC/Neoprene
felt etc. Aluminium sections shall be smooth, rust free, straight,
mitered and jointed mechanically wherever required including
cleat angle, aluminium snap beading for glazing/paneling, CP
Brass/stainless steel screws, all complete as per architectural
drawings and the direction of the Engineer-in-charge, (Glazing
and paneling to be paid for separately).
For Aluminium Louvered fixed in door / windows / ventilator
including fixing arrangement.
Anodised aluminium ( anodised transparent or dyed to required
shade according to IS:1868, Minimum anodic coating of Grade
AC 15),
"
For payment G-plate and Louvered plate should be measured.
Page 27 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
17.2 Providing and laying integral cement based water proofing
treatment including preparation of surface as required for
treatment of roofs, balconies, terraces etc consisting of following
operations: (a) Applying a slurry coat of neat cement using 2.75
kg/sqm of cement admixed with water proofing compound
conforming to IS. 2645 and approved by Engineer-in-charge over
the RCC slab including adjoining walls upto 300 mm height
including cleaning the surface before treatment. (b) Laying brick
bats with mortar using broken bricks/brick bats 25 mm to 115
mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse
sand) admixed with water proofing compound conforming to IS :
2645 and approved by Engineer-in-charge over 20 mm thick
layer of cement mortar of mix 1:5 (1 cement :5 coarse sand)
admixed with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge to required slope and
treating similarly the adjoining walls upto 300 mm height
including rounding of junctions of walls and slabs. (c) After two
days of proper curing applying a second coat of cement slurry
using 2.75 kg/ sqm of cement admixed with water proofing
compound conforming to IS : 2645 and approved by Engineer-
in-charge. (d) Finishing the surface with 20 mm thick jointless
cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed
with water proofing compound conforming to IS : 2645 and
approved by Engineer- in-charge including laying glass fibre cloth
of approved quality in top layer of plaster and finally finishing
the surface with trowel with neat cement slurry and making
pattern of 300x300 mm square 3 mm deep. (e) The whole
terrace so finished shall be flooded with water for a minimum
period of two weeks for curing and for final test. All above
operations to be done in order and as directed and specified by
the Engineer-in-Charge :
17.4.1 For vertical surface two coats @0.70 kg per sqm per coat 150 sqm 468.10 70215.00
17.4.2 For horizontal surface one coat @1.10 kg per sqm. 150 sqm 362.35 54353.00
Page 28 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
17.5 "Extra for finishing the surface by providing and laying China
mosaic finish with approved broken ceramic tile piece (assorted
colour 30% and white tile 70% pieces of size not less than 20 mm
in either direction), as specified and selected by the Engineer, set
evenly over vaults, domes,terrace and similar surfaces to
required profiles and pattern etc. laid over green brick bat coba ,
grouted with mortar as per pattern and instructions of the
Engineer in charge including pointing neatly with white cement
cleaning the finished surfaces and necessary scaffolding, curing
etc. complete.
Page 29 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
19.1 Providing and supplying aluminium extruded tubular and other
aluminium sections as per the architectural drawings and
approved shop drawings , the aluminium quality as per grade
6063 T5 or T6 as per BS 1474,including super durable powder
coating of 60-80 microns conforming to AAMA 2604 of required
colour and shade as approved by the Engineer-in-Charge. (The
item includes cost of material such as cleats, sleeves, screws etc.
necessary for fabrication of extruded aluminium frame work.
Nothing extra shall be paid on this account).
Page 30 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
19.3 Providing, assembling and supplying vision glass panels (IGUs)
comprising of hermetically-sealed 6-12- 6 mm insulated glass
(double glazed) vision panel units of size and shape as required
and specified, comprising of an outer heat strengthened float
glass 6mm thick, of approved colour and shade with reflective
soft coating on surface # 2 of approved colour and shade, an
inner Heat strengthned clear float glass 6mm thick, spacer tube
12mm wide, dessicants, including primary seal and secondary
seal (structural silicone sealant) etc. all complete for the required
performances, as per the Architectural drawings, as per the
approved shop drawings, as specified and as directed by the
Engineer-in-Charge. The IGUs shall be assembled in the factory/
workshop of the glass processor.“(Payment for fixing of IGU
Panels in the curtain glazing is included in cost of item
No.26.2)“For payment, only the actual area of glass on face # 1
of the glass panels (excluding the areas of the grooves and
weather silicone sealant) provided and fixed in position, shall be
measured in sqm.“ (i) Coloured tinted float glass 6mm thick
substrate with reflective soft coating on face # 2, + 12mm Airgap
+ 6mm Heat Strengthened clear Glass of approved make having
properties as visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10 to 20 %,
shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2
degree K etc. The properties of performance glass shall be
decided by technical sanctioning authority as per the site
requirement.
(4) Steel from chowkhats of door, grill, railings, BRC fabric, steel
glazed windows and ventilators.
(5) G.I pipes and fittings
(A) Foundation:-
(i) The brick work and lean concrete is to be dismantled and
demolished upto full depth and width of foundation under the
ground.
(ii) The RCC foundation of RCC structure is to be dismantled and
demolished upto full depth and width of foundation under the
ground.
Page 31 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.1 "Supply, erection and testing of ISI marked ERW M.S. pipes (Class
C - heavy duty) and specials etc. (as per IS:1239 for upto 150 mm
dia and IS:3589 for 200 mm and above) for above ground laying
for hydrants and sprinkler system including transportation of
materials upto the worksite, cutting the pipes to required length,
edge preperation, welding, fixing / erection of pipes including
specials i.e. bends, tees, reducers, flanges, expansion joints and
bellows wherever required, washers, nuts, bolts etc. in proper
position including all supports. jointing by welding, aligning the
pipe line, painting with two primer coat by zinc chromate primer
and two coats of synthetic enamel fire red colour, providing
tapping for pressure gauges and for other instruments etc.
Hydrostatic testing of system at 1.5 times of operating pressure
or 15 kg / sq cm whichever is higher and as specified, flushing &
cleaning by water etc. complete as per drawings & direction of
the Engineer-in-charge.
The pipes and accessories will be provided with all type of
supports (Maximum Support spacing = up to 25 mm dia @ 2 m,
32 mm to 100 mm dia @ 2.5 m, 150 mm & above dia @ 3 m) by
minimum 3 mm thick G.I. clevis / sprinkler hangers / clamps / Tie
rod supports with G.I. nuts, bolts, anchor / dash fastner and
washer for hydrant / sprinkler piping, for 150 mm dia pipe the
support will be through 50x50x6 mm painted / pre galvanized
MS angle iron along with G.I. U clamp, nuts, washers, anchor
fasteners etc as the case may be.
upto 40mm dia. pipe threaded fittings and threaded joints shall
be provided and for 50mm dia & above pipes welded joints shall
be used. The D.I. / Malleable Iron (IS : 1879) fittings shalll be
heavy duty suitable to withstand at least a pressure of 150% of
maximum working pressure with minimum of 15kg/cm2.
(Pipe make : Jindal (Hissar) / Prakash Surya)
(M.I. & D.I. Fitting make : UNIK / Jainsons)
"
Page 32 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.3 "Supply, erection and testing of ISI marked ERW M.S. pipes (Class
C - heavy duty) and specials etc. (as per IS:1239 for upto 150 mm
dia and IS:3589 for 200 mm and above) for above ground laying
for hydrants and sprinkler system including transportation of
materials upto the worksite, cutting the pipes to required length,
edge preperation, welding, fixing / erection of pipes including
specials i.e. bends, tees, reducers, flanges, expansion joints and
bellows wherever required, washers, nuts, bolts etc. in proper
position including all supports. jointing by welding, aligning the
pipe line, painting with two primer coat by zinc chromate primer
and two coats of synthetic enamel fire red colour, providing
tapping for pressure gauges and for other instruments etc.
Hydrostatic testing of system at 1.5 times of operating pressure
or 15 kg / sq cm whichever is higher and as specified, flushing &
cleaning by water etc. complete as per drawings & direction of
the Engineer-in-charge.
The pipes and accessories will be provided with all type of
supports (Maximum Support spacing = up to 25 mm dia @ 2 m,
32 mm to 100 mm dia @ 2.5 m, 150 mm & above dia @ 3 m) by
minimum 3 mm thick G.I. clevis / sprinkler hangers / clamps / Tie
rod supports with G.I. nuts, bolts, anchor / dash fastner and
washer for hydrant / sprinkler piping, for 150 mm dia pipe the
support will be through 50x50x6 mm painted / pre galvanized
MS angle iron along with G.I. U clamp, nuts, washers, anchor
fasteners etc as the case may be.
upto 40mm dia. pipe threaded fittings and threaded joints shall
be provided and for 50mm dia & above pipes welded joints shall
be used. The D.I. / Malleable Iron (IS : 1879) fittings shalll be
heavy duty suitable to withstand at least a pressure of 150% of
maximum working pressure with minimum of 15kg/cm2.
(Pipe make : Jindal (Hissar) / Prakash Surya)
(M.I. & D.I. Fitting make : UNIK / Jainsons)
"
" 40 NB (IS: 1239, 4.0 mm thick)
"
Page 33 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.5 "Supply, erection and testing of ISI marked ERW M.S. pipes (Class
C - heavy duty) and specials etc. (as per IS:1239 for upto 150 mm
dia and IS:3589 for 200 mm and above) for above ground laying
for hydrants and sprinkler system including transportation of
materials upto the worksite, cutting the pipes to required length,
edge preperation, welding, fixing / erection of pipes including
specials i.e. bends, tees, reducers, flanges, expansion joints and
bellows wherever required, washers, nuts, bolts etc. in proper
position including all supports. jointing by welding, aligning the
pipe line, painting with two primer coat by zinc chromate primer
and two coats of synthetic enamel fire red colour, providing
tapping for pressure gauges and for other instruments etc.
Hydrostatic testing of system at 1.5 times of operating pressure
or 15 kg / sq cm whichever is higher and as specified, flushing &
cleaning by water etc. complete as per drawings & direction of
the Engineer-in-charge.
The pipes and accessories will be provided with all type of
supports (Maximum Support spacing = up to 25 mm dia @ 2 m,
32 mm to 100 mm dia @ 2.5 m, 150 mm & above dia @ 3 m) by
minimum 3 mm thick G.I. clevis / sprinkler hangers / clamps / Tie
rod supports with G.I. nuts, bolts, anchor / dash fastner and
washer for hydrant / sprinkler piping, for 150 mm dia pipe the
support will be through 50x50x6 mm painted / pre galvanized
MS angle iron along with G.I. U clamp, nuts, washers, anchor
fasteners etc as the case may be.
upto 40mm dia. pipe threaded fittings and threaded joints shall
be provided and for 50mm dia & above pipes welded joints shall
be used. The D.I. / Malleable Iron (IS : 1879) fittings shalll be
heavy duty suitable to withstand at least a pressure of 150% of
maximum working pressure with minimum of 15kg/cm2.
(Pipe make : Jindal (Hissar) / Prakash Surya)
(M.I. & D.I. Fitting make : UNIK / Jainsons)
"
" 65 NB (IS: 1239, 4.5 mm thick)
"
Page 34 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.7 "Supply, erection and testing of ISI marked ERW M.S. pipes (Class
C - heavy duty) and specials etc. (as per IS:1239 for upto 150 mm
dia and IS:3589 for 200 mm and above) for above ground laying
for hydrants and sprinkler system including transportation of
materials upto the worksite, cutting the pipes to required length,
edge preperation, welding, fixing / erection of pipes including
specials i.e. bends, tees, reducers, flanges, expansion joints and
bellows wherever required, washers, nuts, bolts etc. in proper
position including all supports. jointing by welding, aligning the
pipe line, painting with two primer coat by zinc chromate primer
and two coats of synthetic enamel fire red colour, providing
tapping for pressure gauges and for other instruments etc.
Hydrostatic testing of system at 1.5 times of operating pressure
or 15 kg / sq cm whichever is higher and as specified, flushing &
cleaning by water etc. complete as per drawings & direction of
the Engineer-in-charge.
The pipes and accessories will be provided with all type of
supports (Maximum Support spacing = up to 25 mm dia @ 2 m,
32 mm to 100 mm dia @ 2.5 m, 150 mm & above dia @ 3 m) by
minimum 3 mm thick G.I. clevis / sprinkler hangers / clamps / Tie
rod supports with G.I. nuts, bolts, anchor / dash fastner and
washer for hydrant / sprinkler piping, for 150 mm dia pipe the
support will be through 50x50x6 mm painted / pre galvanized
MS angle iron along with G.I. U clamp, nuts, washers, anchor
fasteners etc as the case may be.
upto 40mm dia. pipe threaded fittings and threaded joints shall
be provided and for 50mm dia & above pipes welded joints shall
be used. The D.I. / Malleable Iron (IS : 1879) fittings shalll be
heavy duty suitable to withstand at least a pressure of 150% of
maximum working pressure with minimum of 15kg/cm2.
(Pipe make : Jindal (Hissar) / Prakash Surya)
(M.I. & D.I. Fitting make : UNIK / Jainsons)
"
" 100 NB (IS: 1239, 5.4 mm thick)
"
Page 35 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.9 "Supply & erection of ISI marked portable fire extinguishers,
confirming to IS:15683, wall mounted type, wall brackets
complete in all respect as per standard item with all accessories,
delivery hose & nozzle whereever required, including fixing on
walls as per the directions of Engineer-in-charge.
Page 36 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.14 "Supply & fixing in position cast iron body double flange dual
plate wafer type check valve (NRV) (PN 16), with SS 304 plates,
hinges, pins, springs, nitrile rubber lining, including
transportation to worksite, supply & fixing SS nuts, SS bolts, 3
mm thick rubber gaskets, complete with testing as per direction
of the Engineer - in - charge.
(MAKE : IVC / Venus / Audco / Advance / SKS / CRI / AIP)
150 NB
"
"
"
32 Each 4770.00 152640.00
21.18 "Providing & fixing standard carbon steel fireman axe with
rubber insulated handle tested to 20000 Volts. (MAKE :
Newage / Safeguard / Padmini / Getech)
"
32 Each 950.00 30400.00
21.19 "Providing Stainless steel ISI marked 63 mm. dia. male
Instantaneous pattern short branch pipes with 15 mm dia.
Nozzle as per IS : 903, suitable for hydrostatic test pressure 21
kg/sqcm and suitable for interconnections to hose pipe coupling
as required. (MAKE : Newage / Safeguard / Padmini / Getech)
"
32 Each 2010.00 64320.00
21.2 "Providing and fixing stainless steel orifice plates at appropriate
places to restrict the pressure up to 3.5 Kg/ Cm2 at different
floors on the hydrant. It shall be inserted between the flange and
hydrant valve. The size of plate being 150 mm, 100 mm or 80
mm dia (as per the case), the orifice diameter to be not less than
50% of the internal dia of pipe into which it is fitted and the plate
thickness shall not be less than 6 mm.
80 mm dia
"
32 Each 1430.00 45760.00
Page 37 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.21 "Supply, installation and testing of cylindrical type flanged
pressure vessel tank, 450 mm dia, 2 m long and of 10 mm thick
M.S., common for a set of fire pumps including flanged
connection, suitable supporting legs with MS plate of size
75x75x5 mm at the bottom and grouted in CC foundation. The
air vessel tank shall be provided with air release valve, stop cock,
safety valve, pressure gauge, 50 mm dia drain valve, suitable
length of connecting pipe and valve from delivery header to
vessel tank, suitable pressure switches to operate main pumps
and jockey pumps, tested to min 25 KG/cm2 complete including
painting with synthetic enamel paint of approved shade with all
accessories as per direction of the Engineer-in-charge. (For Pump
House)
"
Page 38 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.26 "Providing and fixing standard fire hose cabinet (900 mm x 1800
mm x 450 mm) indoor type suitable for accomodating internal
hydrant, hose reel made of not less than 16 SWG MS sheet
having full fronted glass hinged door (5 mm thick glass) including
necessary locking arrangement with handle for housing two nos.
15 meter long fire hose pipes, 30 meter long hose reel, branch
pipe and hydrant valve as required as per drawings, including
brackets for mounting accessories, painting (one coat primer and
two coat of fire red colour). The cabinet shall be mounted on
suitable raised platform. The words ""FIRE HOSE"" to be painted
on the box.
"
One
2 Job 135000.00 270000.00
21.28 "Supplying and laying of 1000 mm wide x 2 mm thick insulated
mat made from highly electrical resistant elastomer of tested
quality to withstand 30 KV dielectric strength as per IS 15652
complete in all respects. (For control Panel)
"
Page 39 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.31 "Providing and laying of ISI marked Aluminium conductor, XLPE
insulated, armoured, served, sheathed Cable 1100 V grade with
terminal joints by palm or pin type cable sockets (lugs),
insulating with tapes, double compression type brass and nickle
plated compression glands. On surface, the cable run shall be on
MS cable trey or fixed on M.S. clamps etc.of suitable size or as
directed by engineer-in- charge, complete in all respects. The
armouring shall be properly connected with the earth
conductor by clamps etc.
(Make : Universal (Satna) / CCI / Nicco / Finolex / Polycab /
Skytone / RR)
16 sqmm 4 core
"
Page 40 of 41
Rate in
Item.No Description of Items Qty Unit Figures in Amount
Rupees
21.36 Providing and fixing mechanical foam type trolley mounted fire
Extinguisher of bearing to IS:10568/IS13385/IS13386 with
relavent discharge time complete.
Capacity 50Lit
2 Each 7425.00 14850.00
21.37 Providing and fixing carbon di oxide type trolley mounted fire
Extinguisher as per IS :2878 with discharge time of 10 to 20
sec /15 to 36 sec/20to 60 sec respectively.
22.5Kg Co2 Fire Extinguisher.
2 Each 12870.00 25740.00
Sub-Total 3059675.00
Total 487354133.00
Page 41 of 41