Professional Documents
Culture Documents
Introduction To SANs Test
Introduction To SANs Test
of SAN fabric elements for potential faults and automatically alerts the network administrator of
problems before they become failures?
Fabric Watch
Fabric Vision
Which 12- or 24-port Fibre Channel switch from HPE is designed and recommended for use in hyper-
scale, private cloud storage, and highly virtualized environments, and supports the “pay-as-you-grow”
model?
Which HPE C-Series enterprise package license feature enables selective transfer of data traffic
between specific initiators and targets on different virtual SANs without merging them into a single
logical fabric?
It starts as a 24-port switch and is expandable to 48 ports within a single switch device.
Which HPE-supported switches are designed to fit into the interconnect bays of the HPE BladeSystem
c-Class enclosure? (Select two.)
You need to reset your HPE B-Series SAN switch to the HPE default settings. What must you do?
Use the configDownload command with a downloaded HPE default configuration file.
Download the latest firmware file from HPE and use the firmwareDownload command.
Call the HPE support center and obtain a specific set of instructions from the support personnel.
What is the out-of-the-factory default username and password for the HPE B-Series SAN switches?
Web Tools
SANXpert
SANtelligence
You installed Web Tools to manage basic zoning and traffic isolation zoning in your SAN environment.
Now, you want to perform advanced tasks such as clone operations for zoning. Which type of license
must you install on the 8Gb or 16Gb HPE B-Series SAN switches?
APM license
EGM license
Which statement is true about the basic (free-of-charge) management capabilities of the HPE B-Series
SAN Network Advisor?
It supports B-series DC SAN Backbone Director and SN8000B 8-Slot SAN Director devices.
What automates multi-switch configuration operations across enabled Brocade SAN switches to save
time and streamline repetitive operations?
QoS zoning
APM
LSAN zoning
EGM
What is the default zoning setting of the HPE C-Series SAN switches?
local access
all access
peer access
no access
Which zoning statements are correct? (Select three.)
If a device is not a member of a zone, it is not accessible by any device within that zone.
The number of zones and zone members are limited by the sum of switch ports in the fabric.
Which Fabric OS zoning enforcement validates only the ELS frames that were used to establish a
session?
You need to completely reset the zoning configuration definitions on your Brocade B-Series SAN
switches. Which other commands must be used in conjunction with the cfgClear command to save the
cleared SDRAM into flash and clear everything on the switch? (Select two.)
cfgDisable
cfgReset
cfgDelete
cfgCreate
cfgSave
cfgPurge
What happens when you merge two fabrics, where one fabric is zoned and the other fabric is unzoned
but set to “no access?”
It allows devices on separate Fibre Channel fabrics to communicate with each other.
Which SAN fabric concept do the dashed circles in this picture represent?
Virtual Fabrics
LSAN zoning
FC-FC routing
You are configuring an HPE 3PAR Smart SAN. Your configuration consists of:
40 initiators
4 target ports
48
40
16
Which statements correctly describe the HPE 3PAR Smart SAN? (Select two.)
It requires HPE H-Series SAN switches with the Enterprise Fabric Management Suite software.
Match each Fibre Channel routing term with its correct definition. (Drag each item in the right column
to the corresponding item in the left column. Let the cursor hover over an item to see its full text.)
virtual fabric
a chain of switches -
from a source switch-
...
path
a collection of port-
s from a set of conn-
...
route
a dynamically assign-
ed path that a devic-
...
hop
a point-to-point lin-
k (an interswitch li-
nk)
Which term refers to transmitting multiplexed traffic from several devices across a single ISL for the
reasons of optimizing the switch utilization?
thin provisioning
oversubscription
storage convergence
auto-provisioning
undersubscription
Which HPE B-Series SAN switch command enables or disables trunking on all ports in the switch?
portCfgTrunkport
trunkEnable | trunkDisable
switchCfgTrunk
What must you do to successfully configure ICLs in a fabric that consists of HPE SN8000B 8-Slot SAN
Backbone Director switches?
You must install the ICL optical cables before installing the enterprise ICL licenses.
If trunking is not enabled on a C-Series port channel, how many VSANs can use this port channel?
none
one
two
four
What is true of adaptive trunking and stacking with the HPE H-Series switches?
Stacking on the HPE SN6000 switch requires two unused 2Gb/4Gb/8Gb switch ports.
Adaptive trunking balances frames across multiple paths between two or more switches.
When the virtual fabrics feature is enabled, a default logical switch is created, containing all switch
ports.
When the virtual fabrics feature is enabled, ISLs are no longer supported.
The default logical switch can only be deleted if you disable the virtual fabrics feature.
Which statements correctly describe the creation and operation of VSANs on HPE C-Series SAN
switches? (Select two.)
Each VSAN has its own fabric services, which cannot communicate by default with devices in other
VSANs.
Which statements correctly describe a routed fabric and routed fabric services? (Select two.)
Routing connects devices in multiple fabrics without extending fabric services from one routed fabric to
another.
A disruption of fabric services in one routed fabric typically affects the entire Meta SAN.
What do HPE B-Series Virtual Fabrics use to share devices across logical fabrics? (Select two.)
Which optional, licensed HPE C-Series SAN switch feature enables you to configure devices in one
VSAN to access devices in another VSAN?
FSPF
IFR
IRF
IVR
What would enable you to implement transparent routing to a remote fabric containing C-Series
devices?
DC Director switch
H-Series switch
You are troubleshooting connectivity issues within an HPE B-Series SAN fabric. What in the
portErrShow output indicates that the problem is likely caused by a bad or damaged cable or a faulty
device in the path?
You are troubleshooting an HPE 3PAR Smart SAN installation. What does the portcfgshow <port
number> command, issued from the HPE B-Series SAN switch, enable you to determine?