Professional Documents
Culture Documents
Installation Checklist Installation Checklist
Installation Checklist Installation Checklist
After removing the carton and shipping material, lift the washer
Connecting Water Lines with Other Appliances
• The LG pedestal washer is designed for use under an LG
front-loading washer. If installing under an LG dryer, additional
5 CONNECTING THE DRAIN HOSES
TO THE DRAIN CONNECTOR 7 LEVELING THE WASHING MACHINE
2
Cold floor firmly. Then check that the washer is perfectly leveled.
STACKING APPLIANCE Wire Clamp Tie Strap
(Use a level.)
Turn the top cover about 180 degrees. Cover the upper hole with • Hybrid dryer with drain hose
the top cover and install 4 short screws (included in packing
box) to fix it in place. Retract all of the legs on the full-size • Front-loading Washer + Turbo Steam Dryer
washer, then position the appliance on the top of the pedestal Tighten all 4 lock
nuts securely using
washer.
the wrench.
Short Installation of Non-Skid Pads
screws For washer Hot
Top cover
Cold If you install the washing machine on a slippery surface, it
may move and become unlevel. Incorrect leveling may cause
Wire Clamp Tie Strap malfunction through noise and vibration. To prevent movement, lay
the non-skid pads under the front leveling feet and adjust the level.
For washer
• Clean the floor to attach the non-skid pads.
Make sure the holes on the pedestal washer align with the holes in Do not install the end of the drain hoses higher than 96 in. • Adjust the level after placing the washing machine in the
the appliance, then install 4 long screws (included in box) at each (243.84 cm) above the bottom of the washer. installation area.
corner to securely attach the appliance to the pedestal washer. • Place the adhesive side of the non-skid pad on the floor.
OPTION 1: STANDPIPE
• Check again that the washing machine is level.
If your drain is a standpipe,
This side up
fasten the drain hose to the
standpipe with the tie strap
provided.
Long Adhesive
screws side
• For Front-loading Washer + Hybrid Dryer see owner's
manual
WARNING Remove backing
4 8
The top cover must be installed to avoid the risk of electric
shock or short circuit. Failure to do so can cause serious CONNECTING THE DRAIN HOSE Drain Hose FINAL CHECKS
injury, fire, electric shock or death. OPTION 2: LAUNDRY TUB
Use the following checklist to make sure you have
Bend the end of the drain completed all of the installation steps. If you are unsure of any of
3
Insert the band clamp (included in packing box) on to the drain
hose to the desired shape the installation steps, please refer to the installation section of the
CONNECTING THE WATER LINES hose elbow. With the hose leading up from the elbow, insert the
and support it on the edge of owner’s manual included with the washer.
elbow onto the drain outlet on the back of the pedestal washer.
the laundry tub. Use the tie
Adjust the band clamp to keep the hose securely in place and ✔ INSTALLATION STEP
strap to secure the drain hose
Check the rubber seals in the hose ends. Connect the water prevent leaking. 1 – REMOVE PACKING MATERIAL
in place.
supply hoses to the HOT and COLD water faucets tightly by 2 – REMOVE FOAM BLOCK, INSTALL COVER
hand and then tighten another 2/3 turn with pliers. Turn on the 3 – CONNECT WATER HOSES
water faucets and check for leaks. 4 – CONNECT DRAIN HOSE
5 – CONNECT POWER CORD
Note Drain Hose
6 – LEVEL WASHER
To ensure sufficient clearance for water lines, allow minimum
6
Once you have completed all six steps, your new washer
clearances of at least 4 in. (10 cm) behind the washer.
CONNECTING THE POWER CORD is ready to use.
Water Faucet * Test for proper operation by running the
Plug the power cord securely into washer through a complete cycle.
Cold water inlet Band Clamp a properly grounded 120V/60Hz
3-prong outlet which is protected * Please consult your Owner’s Manual for
Hot water inlet by a 15-amp fuse or circuit more details.
breaker.
MHK61888731
* Retain it for future reference.
Luego de quitar la caja de cartón y el material de transporte, una secadora LG, se requieren partes adicionales. CONECTOR DE DESAGÜE El tambor de su nueva lavadora gira a velocidades muy altas. Para
levante la lavadora de la base de espuma. Asegúrese de quitar Nota minimizar la vibración, el ruido y el movimiento indeseados, el suelo
el soporte plástico del tambor junto con la base y que no quede debe ser firme y estar perfectamente nivelado.
• Lavadora de carga frontal + Secadora normal
atascado en la parte inferior de la lavadora. Antes de instalar la manguera de desagüe, limpie el interior del uV
erificación de nivelación
tubo independiente con cloro líquido. diagonal
Conecte la manguera de desagüe de la lavadora de tamaño Si el piso no es uniforme, ajuste
Soporte Caliente completo y del pedestal lavador con el conector de desagüe. las patas. Compruebe la nivelación
plástico del Fría moviendo la lavadora firmemente
tambor • Secadora convencional de forma diagonal en ambas
Base de la caja direcciones. Si la lavadora oscila
Lavadora de
de cartón carga frontal cuando presiona la placa superior
de forma diagonal, debe ajustar las
ADVERTENCIA
patas con la llave incluida.
¡Los materiales de embalaje pueden ser peligrosos para los niños! Grifo
Mantenga todos los materiales de embalaje (cartón, espuma, bolsa
de plástico, etc.) fuera del alcance de los niños. uA
segúrese de que las cuatro patas se mantengan estables
Fría
y se apoyen firmemente en el suelo. Luego, compruebe que
2
Abrazadera Precintos la lavadora esté perfectamente nivelada. (Utilice un nivel.)
MONTAJE DEL APARATO de alambre
8
largos
• Para lavadora de carga frontal + secadora híbrida,
consulte el manual del propietario. Manguera de desagüe COMPROBACIONES FINALES
3
OPCIÓN 2: LAVABO Utilice esta lista de comprobación para asegurarse de que ha
4
CONEXIÓN DEL SUMINISTRO DE AGUA Doble el extremo de la realizado todos los pasos de la instalación.
CONEXIÓN DE LA MANGUERA DE DESAGÜE manguera de desagüe de la Si no está seguro de alguno de los pasos de la instalación, consulte la sección
manera deseada y apóyelo de instalación del manual del propietario suministrado con la lavadora.
Revise las juntas de goma de los extremos de las mangueras. Conecte sobre el borde del lavabo.
Inserte la abrazadera de banda (incluida en la caja de embalaje) ✔ PASO DE INSTALACIÓN
las tuberías de agua a los grifos de agua caliente y fría y apriete las Utilice un precinto para fijar la
en el codo de la manguera de desagüe. Con la manguera 1 – RETIRAR EL MATERIAL DE EMBALAJE
conexiones con la mano. A continuación, utilice unos alicates para manguera de desagüe en su
apuntando hacia arriba desde el codo, inserte el codo en la 2 – EXTRAER LOS PERNOS DE EMBALAJE
apretarlas otro 2/3 de vuelta. Abra los grifos de agua y compruebe que posición.
salida de desagüe que se encuentra en la parte posterior 3 – CONECTAR LAS MANGUERAS DE AGUA
no haya filtraciones.
del pedestal lavador. Ajuste la abrazadera para mantener la Manguera de desagüe 4 – CONECTAR LA MANGUERA DE DRENAJE
Nota manguera en su lugar y evitar fugas. 5 – CONECTAR EL CABLE DE CORRIENTE
6
Para garantizar que haya espacio suficiente para las tuberías de agua, deje un 6 – NIVELAR LA LAVADORA
espacio libre mínimo de 4 pulgadas. (10 cm) detrás de la lavadora. CONEXIÓN DEL CABLE DE ALIMENTACIÓN Su nueva lavadora estará lista para ser utilizada una vez
que haya realizado estos seis pasos.
Grifo del agua
Conecte el cable de alimentación * P ruebe que la lavadora funcione apropiadamente
de manera segura a un haciéndola funcionar un ciclo completo.
Entrada de agua fría tomacorriente para enchufes
de 3 clavijas de 120 V/60 Hz * Consulte su Manual del Propietario para
Entrada de agua caliente conectado a tierra y protegido obtener más detalles.
Abrazadera para manguera por un disyuntor o fusible de 15
amperios. * Consérvelo para futuras referencias.