Professional Documents
Culture Documents
Procedure To Process, Harmonize and Analyze Grip Tester Measurements
Procedure To Process, Harmonize and Analyze Grip Tester Measurements
Procedure To Process, Harmonize and Analyze Grip Tester Measurements
ABSTRACT
Skid Resistance data is affected by several factors, such as temperature, climate seasonal
variations, pavement surface conditions and operation of devices. Therefore, measures may
differ considerably between each other and cannot be compared directly. This is especially
critical when comparing skid resistance between different devices as they may also differ in the
measuring principal being used.
The study proposes a procedure to process and analyze skid resistance values measured
with Grip Tester and, harmonize them to SCRIM (Sideway Coefficient Routine Inspection
Machine) measures. The method considers four steps. First invalid data is detected and
eliminated. Second, adjustment factors to correct temperature and speed variations are applied.
Third, processed Grip Tester measurements are harmonized to SCRIM values. And finally, an
analysis methodology to detect outlier data, singularities, data structural changes and
segmentation is presented.
To estimate adjustment factors measurements with Grip tester were performed at
different speeds and in roads presenting important temperature oscillations. Finally, to harmonize
Grip Tester measurements to SCRIM values, a particular method was developed based on the
PIARC (World Road Association) experiment.
From the study it was concluded that Grip Tester values have to be processed and
corrected due to external factors affecting the measuring procedure. Once data is processed and
harmonized, it can be analyzed and compared to measures obtained with other devices.
INTRODUCTION
Grip tester is a trailer that measures continuously and dynamically the longitudinal skid
resistance coefficient of a pavement expressed as Grip Number (GN). Skid resistance is obtained
in terms of the friction force observed between a partially locked wheel and the wet pavement.
Measures may vary with temperature, climate seasonal variations, pavement surface
conditions and the operation of the equipment. Measures performed with the same Grip Tester or
between different Grip Testers can differ considerably because of these factors.
Harmonization of Grip Tester with other devices is required when their measures need to
be compared. This is because different devices measure skid resistance according to diverse
principals. In the case of SCRIM (Sideway Coefficient Routine Inspection Machine), skid
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 2
coefficient is measured with a wheel at an angle of 20° to the direction of travel. Therefore, the
transverse skid resistance of a pavement is obtained in terms of the SCRIM values (Sideway-
Force Coefficient: SFC).
A research project lead by the Pontificia Universidad Católica de Chile in partnership
with the public and private sector has been studying the skid resistance phenomena in Chile
during the last four years. From this, a friction standard was developed for Chile. One of the
scopes of the project was to define clear and precise procedures for the measurement of skid
resistance with different devices. This paper presents the results of the processing and analysis
procedure of Grip Tester measurements, considering also the harmonization of these measures to
SCRIM values (SFC).
Research Methodology
The research methodology followed for the development of the procedure considered
three different experiments: temperature tests, speed tests and the harmonization experiment.
Previous to these experiments a repeatability test was held with each device considered in the
study. The measuring methodology and the repeatability tests followed a standard procedure
described in detail in de Solminihac et al. (1; 2). This was done to ensure the precision and
reliability of each device under constant testing conditions. From these, repeatability of Grip
Tester devices, SCRIM and laser profiler was checked and approved.
To estimate the temperature factor, measures with Grip Tester were performed in roads
presenting different climates and important daily temperature oscillations. Measures showed a
considerable difference when temperatures ranged between 15°C and 40°C.
To obtain the speed factor, measures with three different Grip Testers were performed at
30 km/h, 50 km/h and 70 km/h. Tests were performed in roads presenting different geometrical
and surface characteristics.
Finally, to harmonize Grip Tester measurements to SFC, tests were performed with both
devices at 30km/h, 50 km/h and 70 km/h in road sections presenting different skid resistance and
macro texture levels. Macro texture of the selected sections was evaluated with a laser profiler. A
particular method was developed to harmonize the devices based on the PIARC (World Road
Association) experiment (3; 4) and the HERMES experiment (5; 6).
Data obtained from the three main experiments was analyzed in detail. Correction factors,
harmonization requirements and a methodology to detect outlier data, singularities, data
structural changes and segmentation were defined from this analysis. As the final result of these,
the procedure to process, harmonize and analyze grip tester measurements was designed and
developed.
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 3
General Framework
The proposed procedure considers the four general steps presented in Figure 1 and described as
follows:
Field Data
Need to YES
Harmonize? STEP 3 Harmonization
Equivalent Side Force
Coefficient (SFCe)
NO
Segmented Data
- STEP 1: Grip Tester data obtained from the field is pre-processed by detecting and
eliminating invalid data.
- STEP 2: Adjustment factors to correct temperature and speed variations are applied to the
preprocessed data. The output of the data processing is an Adjusted Grip Number (GNA).
- STEP 3: The Adjusted Grip Number (GNA) values are harmonized to SFC. This step
needs to be considered when skid resistance thresholds of a road network are defined in
terms of SFC. The output of this step is an Equivalent Sideway-Force Coefficient value
(SFCe).
- STEP 4: An analysis methodology to detect outlier data, singularities and data structural
changes is applied to the harmonized values. As a result of this final step, the analyzed
data is segmented and reported.
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 4
This temperature adjustment factor is applied only during summer months, as during the
rest of the year temperature oscillations do not affect measures significantly. It has to be noticed
that the temperature factors were developed for Chilean temperature regimes and seasonal
conditions. It is recommended that similar factors should be developed for local conditions,
when not available.
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 5
V − Se2 Se1 −V
Where, Sp1 and Sp2 are speed constants; V is the reference speed; Se1 and Se2 are the
measuring speeds of Grip Tester and SCRIM respectively; and, A1 and B1 are calibration
constants.
With these two equations an equivalent SFC value can be estimated from a GN value
obtained from a Grip Tester (GNp) that is representative of a Grip Tester fleet. The equations
consider the correlation existing between macrotexture and skid resistance through the speed
constants Sp1 and Sp2. The V constant is used to optimize the calibration between both
equipments. In the PIARC experiment, from where IFI was derived, this speed was 60 Km/h,
whereas in the EFI experiment this value was from 30 Km/h.
An important issue is that the GNp value considered in the equations represents the GNA
value of a particular device harmonized to a virtual Grip Tester representative of a Grip Tester
fleet. When calibrating Equations 6 and 7 to local conditions, it is recommended that the virtual
Grip Tester should be estimated in terms of the mean GN values of a fleet.
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 6
As an output of this step within the overall procedure, the SFCe value for a specific Grip
Tester is obtained, which was already processed in the previous steps. This data is of particular
relevance when comparing Grip Tester values to thresholds defined in terms of SFC.
Outlier Detection
Outliers are defined as data points observed beyond the GNA tendency. Outliers can be
identified with the Leverage Test. The method measures the distance of an observed sample
compared to a set of means (hi). This distance is the diagonal of a hat matrix in a linear
regression. This distance is calculated with Equation 8.
1 (x i − x) 2
hi = + (8)
n (n − 1)S2x
Where n is the total data contained in the i-esim data set, x is the mean of the sample and
2
S is the standard deviation. The limit value of h is calculated with Equation 9:
x
i
6
hi ≤ (9)
n
This method was implemented in a digital worksheet, to simplify its application. Outlier
detected in this step are not considered in the following steps, but have to be reported, and should
not be eliminated from the final data report.
Preliminary Segmentation
Skid resistance threshold are defined as function of special sites category (such as straight lanes,
horizontal curves, stopping site such as toll places or traffic signs). Then, to each site category
are associates a specific threshold value. To compare on a common basis thresholds and GNA
data, a first segmentation should be performed. The segmentation split GNA data into each site
category existent on the lane measured.
Where n is the total data contained in the analyzed section, xj is the value of the
measurement in point j and x is the mean of the measurement in the analyzed section. The point
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 7
where g(i) is maximum in a section, is the point where the mean changes. It is also the first point
of the second segment of the same section. The procedure is repeated in both segments,
obtaining new maximum points g(i). The process ends when the function g(i) does not present
more maximum points within.
In some cases contiguous segments have similar means. Therefore, a statistical analysis has
to be applied to identify whether it is possible to combine in one section means and standard
deviations. With this, the number of segments obtained from the previous step is reduced. The
following rules are applied for this:
- If in two isolated consecutive segments the t-student test verifies the null hypothesis of
equity of means, then the two segments are grouped together. The mean and standard
deviation are recalculated for the new segment.
- When three or more consecutive segments verify the null hypothesis of equity of means
in each pair of consecutive segments, an analysis of variance for repeated measures is
applied (ANOVA). Then, the Tuckey test of multiple comparisons is applied. If the null
hypothesis of equity of means is verified for the group of segments, then the segments
can be grouped together. Else, only consecutive segments that verify the Tuckey test can
be grouped together.
The outputs of this step are a series of segments with different length, where consecutive
segments present means and standard deviations statistically different. Therefore, each segment
represents the change point of the mean value of GNA.
CONCLUSIONS
This paper presented a general procedure for processing, harmonizing and analyzing skid
resistance values measured with Grip Tester. With this, skid resistance data can be analyzed
systematically and be consistently compared to threshold values defined in terms of SCRIM
measures (SFC), or else in terms of other measures.
From the study it was observed that skid resistance values measured in warm seasons are
affected by daily temperature oscillations. An adjustment factor was therefore proposed to
standardize Grip Tester values measured under different temperature conditions during warm
seasons.
Skid resistance values are also affected by measuring speed. Skid resistance
measurements performed under heterogeneous traffic conditions may present considerable
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).
7th International Conference on Managing Pavement Assets (2008)
De Solminihac, Chamorro, and Echaveguren Page 8
alterations. The speed adjustment factor proposed in the present study standardizes measures
performed at any speed to a reference speed of 50 Km/h.
When skid resistance thresholds are referred to a specific device, measurements from
other devices need to be harmonized to this equipment. This is the case of the Chilean standard,
which is defined in terms of SCRIM values (SFC). The harmonization method presented in this
study is applied to the case when Grip Tester measurements (GN) need to be harmonized to SFC.
However, the proposed method can be generalized and applied with other devices.
Skid resistance measurements generally present high variability. Therefore, an essential
final step considered in the proposed procedure is the statistical analysis of data. This is
especially important when comparing skid resistance data to threshold values. The analysis
procedure proposed in the study considers the identification of outlier data, structural changes in
the skid resistance measures and a consistent segmentation process.
ACKNOWLEDGMENTS
The authors are gratefully acknowledged to the partners and sponsors of the Research Project
FONDEF D03I 1042: FONDEF-CONICYT Fondo de Fomento al Desarrollo Científico y
Tecnológico, Dirección Nacional de Vialidad del Ministerio de Obras Públicas de Chile,
Sociedad Concesionaria Autopista del Maipo, Sociedad Concesionaria Talca-Chillán, Sociedad
Concesionaria Ruta de La Araucanía and Sociedad Concesionaria Ruta de los Ríos.
REFERENCES
1. de Solminihac, H. Echaveguren, T. Chamorro, A. Vargas, S. y Bustos, M. Procedimiento
de Medición y Procesamiento de Datos de Resistencia al Deslizamiento Medidos con
Equipo Grip Tester. Technical Document TM-014-06-1. FONDEF D031 – 1042.
Pontificia Universidad Católica de Chile. 2007a
2. De Solminihac, H. Echaveguren, T. Chamorro, A. Vargas, S. y Bustos, M. Procedimiento
de Medición y Procesamiento Datos de Resistencia al Deslizamiento Medidos con
Equipo SCRIM. Technical Document TM-014-06-2. FONDEF D031 – 1042. Pontificia
Universidad Católica de Chile. 2007b.
3. Wambold, J. Antle, C. Henry J.J., and Rado, Z. International PIARC experiment to
Compare and Harmonize Texture and Skid Resistance Measurments. Technical
Commiteé C1. PIARC. 1995.
4. ASTM. Standard Practice for Calculating International Friction Index of Pavement
Surface. ASTM E 1960 – 98. 1998.
5. Descornet, G. Proposal for a European Standard in Relation with the Skid Resistance of
Road Surfacings. Final Report, Program of scientific support to standardization, part III.
Belgian Road Research Centre. Brussels, Belgium. 1998.
6. Gothié, M. Harmonisation of European Routine and Research Measurement Equipment
for Skid Resistance of Roads and Runways. The HERMES Project”. SURF 2004. 5th
Symposium on Pavement Surface Characteristics. Toronto, Canada, June 6th - 10th.
2004.
7. ASTM Standard Practice for Calculating the International Runway Friction Index, ASTM
E2100-04. 2004.
TRB Committee AFD10 on Pavement Management Systems is providing the information contained herein for use by individual practitioners
in state and local transportation agencies, researchers in academic institutions, and other members of the transportation research
community. The information in this paper was taken directly from the submission of the author(s).