Professional Documents
Culture Documents
HDIA Mic Preamp / USB Audio Interface: Owner'S Manual
HDIA Mic Preamp / USB Audio Interface: Owner'S Manual
UH-7000
HDIA Mic Preamp / USB Audio Interface
OWNER'S MANUAL
Before connecting this unit to a computer, you must download and install a dedicated driver.
IMPORTANT SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclo-
sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
For U.S.A.
This appliance has a serial number located on the bottom
INFORMATION TO THE USER panel. Please record the model number and serial number
This equipment has been tested and found to comply and retain them for your records.
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide Model number
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and Serial number
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures.
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and
receiver.
c) Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician Nameplate
for help.
CAUTION
Changes or modifications to this equipment not expressly
approved by TEAC CORPORATION for compliance could void
the user’s authority to operate this equipment.
For Canada
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A
LA NORME NMB-003 DU CANADA.
DECLARATION OF CONFORMITY
We, TEAC EUROPE GmbH. Bahnstrasse 12, 65205
Wiesbaden-Erbenheim, Germany declare in own
responsibility, the TEAC product described in this
manual is in compliance with the corresponding
technical standards.
2 TASCAM UH-7000
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions. CAUTION
• Do not expose this apparatus to drips or splashes.
3 Heed all warnings.
• Do not place any objects filled with liquids, such as vases,
4 Follow all instructions.
on the apparatus.
5 Do not use this apparatus near water.
• Do not install this apparatus in a confined space such as a
6 Clean only with dry cloth. book case or similar unit.
7 Do not block any ventilation openings. Install in accordance • The apparatus should be located close enough to the AC
with the manufacturer's instructions. outlet so that you can easily grasp the power cord plug at
8 Do not install near any heat sources such as radiators, heat any time.
registers, stoves, or other apparatus (including amplifiers) • If the product uses batteries (including a battery pack
that produce heat. or installed batteries), they should not be exposed to
9 Do not defeat the safety purpose of the polarized or sunshine, fire or excessive heat.
grounding-type plug. A polarized plug has two blades with • CAUTION for products that use replaceable lithium
one wider than the other. A grounding type plug has two batteries: there is danger of explosion if a battery is
blades and a third grounding prong. The wide blade or the replaced with an incorrect type of battery. Replace only
third prong are provided for your safety. If the provided with the same or equivalent type.
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched WARNING
particularly at plugs, convenience receptacles, and the point • Products with Class ! construction are equipped with a
where they exit from the apparatus. power supply cord that has a grounding plug. The cord
11 Only use attachments/accessories specified by the manufac- of such a product must be plugged into an AC outlet that
turer. has a protective grounding connection.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. 88 For European Customers
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over. Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed
of separately from the municipal waste stream via desig-
nated collection facilities appointed by the government or
the local authorities.
(b) By disposing of the electrical and electronic equipment
correctly, you will help save valuable resources and prevent
any potential negative effects on human health and the
environment.
(c) Improper disposal of waste equipment can have serious
effects on the environment and human health as a result
13 Unplug this apparatus during lightning storms or when of the presence of hazardous substances in electrical and
unused for long periods of time. electronic equipment.
14 Refer all servicing to qualified service personnel. Servicing is (d) The crossed out wheeled dust bin symbol
required when the apparatus has been damaged in any way, indicates that electrical and electronic equipment
such as power-supply cord or plug is damaged, liquid has must be collected and disposed of separately
been spilled or objects have fallen into the apparatus, the from household waste.
apparatus has been exposed to rain or moisture, does not
(e) The return and collection systems are available to
operate normally, or has been dropped.
the end users. For more detailed information about disposal
of old electrical and electronic equipment, please contact
• The apparatus draws nominal non-operating power from your city office, waste disposal service or the shop where
the AC outlet with its POWER or STANDBY/ON switch not in you purchased the equipment.
the ON position.
• The mains plug is used as the disconnect device, the 88 For China
disconnect device shall remain readily operable.
• Caution should be taken when using earphones or 产品有毒有害物质或元素的名称及含量
headphones with the product because excessive sound 机种 : UH-7000 有毒有害物质或元素
pressure (volume) from earphones or headphones can 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
品名
cause hearing loss. (Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE)
• If you are experiencing problems with this product, contact 1 CHASSIS部份 ○ ○ ○ ○ ○ ○
2 PCB Assy部份 × ○ ○ ○ ○ ○
TEAC for a service referral. Do not use the product until it
has been repaired. 3 线材部份 ○ ○ ○ ○ ○ ○
4 附属品部份 ○ ○ ○ ○ ○ ○
5 SEAL部份 ○ ○ ○ ○ ○ ○
6 包装部份 ○ ○ ○ ○ ○ ○
○:表示该有毒有害物质在该部件所有均质材料中的含有量
均在 SJ/T11363-2006 标准规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的
含量超出 SJ/T11363-2006 标准规定的限量要求。
(针对现在代替技术困难的电子部品及合金中的铅)
TASCAM UH-7000 3
Contents
1 – Introduction...............................................5 Using the unit as an A/D and D/A converter.....25
Features................................................................................... 5 Saving Mixer Panel settings
Included items...................................................................... 5 to the unit memory....................................................25
Conventions used in this manual................................... 5 6 – Standalone Mode.....................................26
Trademarks............................................................................. 6 Overview...............................................................................26
Precautions for placement and use............................... 6 Settings in standalone mode.........................................26
Power supply......................................................................... 6
Beware of condensation.................................................... 6 7 – Application Guide....................................27
Cleaning the unit................................................................. 6 Windows XP and Windows Media Player..................27
Using the TEAC Global Site............................................... 6 Windows 7 and Windows Media Player.....................27
User registration................................................................... 6 Windows 8 and Windows Media Player.....................28
Mac OS X and iTunes........................................................28
2 – Names and Functions of Parts..................7 Audio MIDI Setup in OS X Mavericks (10.9.1)...........28
3 – Installation.................................................9 8 – Troubleshooting.......................................29
System requirements.......................................................... 9
Windows........................................................................... 9 9 – Specifications...........................................31
Mac OS X.......................................................................... 9 Audio resolution.................................................................31
Installing the driver............................................................. 9 Analog audio input and output ratings.....................31
Installing the driver for Windows............................ 9 Analog inputs...............................................................31
Installing the driver for Mac OS X..........................10 Analog outputs............................................................31
Uninstalling the driver...............................................12 Digital audio input/output ratings..............................31
Digital input..................................................................31
4 – Connections..............................................13 Digital output...............................................................31
USB connection..................................................................14 Control input/output ratings.........................................31
Audio connections............................................................14 Audio performance...........................................................31
Microphones.................................................................14 Computer system requirements...................................32
Digital connections with sound modules, Windows.........................................................................32
MD/CD players and other audio sources............14
Mac OS X........................................................................32
Analog connections with electronic
Supported audio drivers...........................................32
instruments and other audio equipment..........14
General..................................................................................32
Analog record players................................................14
Dimensional drawings.....................................................33
Monitor speakers.........................................................14
Audio flow diagram...........................................................34
Headphones..................................................................14
4 TASCAM UH-7000
1 – Introduction
Thank you for purchasing the TASCAM UH-7000 HDIA Mic 88 Note about computer operation
Preamp/USB Audio Interface.
If you are unsure about anything related to the basic operation
Before connecting and using this unit, please take time to of a computer when it is mentioned in an explanation in this
read this manual thoroughly to ensure you understand how to manual, please refer to the computer operation manual.
properly set it up and connect it, as well as the operation of its
many useful and convenient functions. After you have finished A dedicated driver must be installed on a computer to use this
reading this manual, please keep it in a safe place for future unit with it. For details about driver installation, see “Installing
reference. the driver” on page 9.
You can also download the Owner's Manual from the TEAC
Global Site (http://teac-global.com/). Included items
Should the contents of the memory of a connected device
(including hard disks and optical discs) in the same system as This product includes the following items.
this unit be lost, our company will bear no responsibility for
repair, including for compensation. Take care when opening the package not to damage the items.
Keep the packing materials for transportation in the future.
Please contact the retailer where you purchased this unit if any
Features of these items are missing or have been damaged during trans-
portation.
• This product uses high quality parts that have established • Main unit...............................................................................................× 1
records of use in professional audio equipment and • Power cord............................................................................................× 1
our unique TASCAM High Definition Instrumentation
Architecture (HDIA) mic preamps (−128dBu EIN) to provide • USB cable..............................................................................................× 1
mic preamp circuits and AD/DA converters of outstanding • Warranty card......................................................................................× 1
audio quality • Quick Start Guide...............................................................................× 1
• The temperature-compensated crystal oscillator (TCXO) for
the internal audio clock has 1ppm precision
• Supports up to 192kHz/24-bit resolution Conventions used in this manual
• Audio interface function supports up to 4 channels of
inputs and outputs (2 analog and 2 digital) using USB 2.0 The following conventions are used in this manual.
(type B connector) • Buttons, connectors and other physical parts of this unit are
• Includes 2 channels of balanced XLR mic inputs that can written using a bold font like this: PHONES LEVEL knob.
provide +48V phantom power and 2 channels of balanced • Information shown on the computer display is written like
TRS inputs this “OK”.
• Analog outputs include XLR line and headphones outputs • As necessary, additional information is provided under TIP,
• XLR digital input and output support both AES/EBU and S/ NOTE and CAUTION headings.
PDIF formats
• Each mic/line input (INPUT 1/INPUT 2) has a dedicated large
TIP
trim knob that allows precise level adjustment These are tips about how to use the unit.
• Each mic/line input (INPUT 1/INPUT 2) has a large LED level NOTE
meter (with 20 bars each) that is very visible
These provide additional explanations and describe special
• Link line function enables adjustment of line output levels cases.
• Built-in AC power supply with a three-prong inlet
• Chassis and trim knobs use thick aluminum materials CAUTION
• Half-rack size can be used in various situations, including as Failure to follow these instructions could result in injury,
damage to equipment or lost recording data, for example.
a desktop module or mounted in a rack
• The MIXER PANEL button on the front of the unit can be
used to quickly open a screen on the computer display
where settings can be changed
• On-board digital mixer allows input from the audio inputs
and the computer to be mixed and output
• Built-in DSP effect processor allows dynamics effects to be
applied to the inputs and send effects to be used on a send
bus (operation possible from computer)
• Multitrack mode supports multitrack recording (when used
with a DAW, for example)
• Direct monitoring function allows input monitoring with
low latency
• Dedicated drivers and applications available for both
Windows and Mac operating systems
• Standalone mode allows this unit to be used when not
connected to a computer
• Standalone mode operation settings can be changed
according to the use conditions and other needs
TASCAM UH-7000 5
1 – Introduction
6 TASCAM UH-7000
2 – Names and Functions of Parts
Front panel
TASCAM UH-7000 7
2 – Names and Functions of Parts
Rear panel
CAUTION
• USB 1.1 is not supported.
• When connected to a USB 3.0 port, it will function in High
Speed mode equivalent to USB 2.0 (480 Mbps maximum).
• This unit does not support computer suspend (sleep) mode,
so the unit might not function properly after this mode
ends. In this case, reconnect the USB cable.
y DIGITAL (AES/EBU) IN jack
This digital audio input connector supports the IEC 60958
professional (AES/EBU) and consumer (S/PDIF) standards.
u DIGITAL (AES/EBU) OUT jack
This digital audio output connector supports the IEC 60958
professional (AES/EBU) and consumer (S/PDIF) standards.
i AC IN connector
Plug the included power cord in here.
8 TASCAM UH-7000
3 – Installation
System requirements Installing the driver
For the latest information about supported operating systems, A driver must be installed on a computer to use this unit with it.
visit the TEAC Global Site (http://teac-global.com/). Drivers are constantly being updated. Download the latest
driver for the operating system you are using from the TEAC
Global Site (http://teac-global.com/).
Windows
CAUTION
88 Supported operating systems • Since digital audio signal processing puts a fairly heavy
Windows 8 (including 8.1) 32-bit load on the computer, the operation of other applications,
Windows 8 (including 8.1) 64-bit particularly graphic-intensive applications and Internet
tools, could cause processing to fall behind. Do not run
Windows 7 32-bit SP1 or later other applications when using audio applications.
Windows 7 64-bit SP1 or later • Restarting the computer might be necessary after instal-
Windows XP 32-bit SP3 or later lation or uninstallation completes. Save your data and
(Windows Vista and Windows XP 64-bit are not supported.) conduct other necessary steps in other applications before
quitting them.
88 Computer hardware requirements
Windows computer with a USB 2.0 port
Installing the driver for Windows
88 CPU/processor speed
2 GHz or faster dual core processor (x86) NOTE
• Install the driver on the computer before connecting the
88 Memory unit to it with the USB cable.
2 GB or more If you already connected the USB cable, and the Found New
Hardware Wizard launched, cancel and quit the wizard and
CAUTION disconnect the USB cable.
Operation of this unit was confirmed using standard • When installing the driver, a warning might appear with a
computers that meet the above requirements. This does message such as, “The software you are installing for the
not guarantee operation with all computers that meet the hardware has not passed Windows Logo testing to verify its
above requirements. Even computers that meet the same compatibility with Windows.” If this message appears, click
system requirements might have processing capabilities “Continue Anyway” to proceed with the installation.
that differ according to their settings and other operating
conditions. 88 Driver installation procedures
1. Download the latest driver for the operating system you are
using from the TEAC Global Site (http://teac-global.com/)
Mac OS X and save it on the computer to be used with the unit.
88 Supported operating systems 2. Open the saved driver (zip file) on, for example, the
computer desktop.
OS X Mavericks (10.9.1 or later) 3. Double-click the setup.cmd file in the folder that was
OS X Mountain Lion (10.8.4 or later) created when you opened the zip file.
OS X Lion (10.7.5 or later)
CAUTION
Mac OS X Snow Leopard (10.6.8 or later)
If you open a zip file without decompressing it and
88 Computer hardware requirements double-click the “setup.cmd” file in the folder that opens,
installation will not start. Right-click the zip file and select
Apple Macintosh computer with a USB 2.0 port
“Extract All”, for example, to decompress it and then try
88 CPU/processor speed again.
4. When the language selection screen (below) appears, select
2 GHz or faster dual core processor
the language you prefer and then click the “OK” button. (The
88 Memory screens and button names used in the following instructions
are for when English is selected.)
2 GB or more
5. Click the “Install the driver” button when the screen below
appears.
TASCAM UH-7000 9
3 – Installation
NOTE
Depending on the computer’s settings, the downloaded
dmg file might not have opened automatically. In this case,
open the dmg file first and then double-click the disk image
file.
3. After the installer launches, follow the instructions on the
screen to proceed with the installation.
Computer
USB
10 TASCAM UH-7000
3 – Installation
When the Gatekeeper setting is “Allow applications Changing the Gatekeeper setting
downloaded from: the Mac App Store” The Gatekeeper setting can be changed using the “Allow
“'TASCAM UH-7000 X.XX' can't be opened because it was applications downloaded from:” item on the “General” page
not downloaded from the Mac App Store.” might appear as a of the “Security & Privacy” pane of the System Preferences.
security warning message. To change this, you must click the lock icon ( ) at the
bottom left and enter a password to unlock the settings.
CAUTION
Changing the Gatekeeper settings could result in security
This message might also appear when the Gatekeeper risks.
setting is something other than “Allow applications
If you changed the Gatekeeper setting to decrease security
downloaded from: the Mac App Store”.
(use one of the lower settings), set it back to the original
If the “'TASCAM UH-7000 X.XX' can't be opened because setting after updating the driver and/or firmware.
it was not downloaded from the Mac App Store.” security
warning message appears again, you might not be able to
open the file.
In this case, copy the file from the folder where it is to the
desktop or another folder, and then open it. Alternatively,
change the Gatekeeper settings to “Allow applications
downloaded from: the Mac App Store and identified devel-
opers” and try opening it again.
When the Gatekeeper setting is not “Allow
applications downloaded from: the Mac App Store”
“'TASCAM UH-7000 X.XX' is an application downloaded
from the Internet. Are you sure you want to open it?” might
appear as a security warning message. In this case, click the
“Open” button.
TASCAM UH-7000 11
3 – Installation
88 Mac OS X
Uninstalling the driver
1. Double-click the “TASCAM_UH-7000_driver_X.XX.dmg” disk
88 Windows image file that was used during installation, and double-
There are two ways to uninstall the driver. click “TASCAM UH-7000 remover” inside the folder.
NOTE
In Windows 8, to open the Control Panel, right-click the Start
screen and click the All apps button (or x button in Windows
8.1) that appears at the bottom right of the screen.
2. If “View by:” is set to “Category” (Category View in Windows
XP), click “Uninstall a program” under the “Program” item.
If “View by:” is set to “Large icons” or “Small icons”(Classic
View in Windows XP), click “Programs and Features”.
3. Double-click “UH-7000 drivers” in the list.
4. Then, follow the instructions that appear on the screen.
12 TASCAM UH-7000
4 – Connections
Headphones
Computer
TASCAM UH-7000 13
4 – Connections
14 TASCAM UH-7000
5 – Mixer Panel Settings
You can use the Mixer Panel to change and save settings for the The INTERFACE page is divided into two areas. One shows the
various functions of the unit. status of the unit and the other shows settings.
Mixer
Headphones
UH-7000
PHONES
TASCAM UH-7000 15
5 – Mixer Panel Settings
16 TASCAM UH-7000
5 – Mixer Panel Settings
NOTE
• Selection will not be possible when an effect cannot be used
because of sampling frequency conditions.
• Turning the dynamics effect on/off using these buttons is
linked to the dynamics effect on/off setting on the EFFECT
page.
• When the sampling frequency is 44.1 kHz or 48 kHz, both
the limiter and low-cut filter functions can be used together
at the same time. When using these two effects at the
same time, the send effect cannot be used. (See “Dynamics
effects” on page 20.)
4 Dynamics effects assignment buttons
Click the buttons for each channel and the MASTER L/R
button to assign the dynamics effect to it.
Use the MIXER page to make settings for the built-in mixer and
output signals. You cannot assign the dynamics effect to more than one
channel at a time.
The contents of this screen depend on the Mixer Mode setting
on the INTERFACE page. Options
Off (default): Channel name button unlit
NOTE
On: Assigned channel name button lit
All settings except for the status of the SOLO buttons made
To change the channel to which the dynamics effect is
on the MIXER page are retained even when the unit is turned
assigned, click the channel name button of the desired
off. The solo buttons are reset to their default values (off)
channel. The previously assigned channel name button will
whenever the unit is turned off.
become unlit, and the newly assigned channel name button
1 MON MIX slider will light.
If the Mixer Mode setting on the INTERFACE page is set to
Multitrack, you can use the slider to adjust the balance of
5 Analog input switches
Select the analog inputs for the Analog 1 and Analog 2
the signal output from the built-in mixer.
channels.
Slide it all the way to the Input side to output only the
The button for the selected input lights.
signals input to this unit, or slide it all the way to the
Computer side to output only the signals output from the LINE button: Input from the ANALOG (BALANCED) LINE IN
computer to the unit by USB. 1/2 jacks.
Click the slider and drag it left and right to adjust it. MIC button: Input from the ANALOG (BALANCED) MIC IN
1/2 jacks.
If the Mixer Mode setting on the INTERFACE page is set to
Stereo Mix, the MON MIX slider will not appear. The signals 6 Effects send selection buttons
input through each input jack and from the computer Set whether the signal sent to the send bus is pre-fader or
output will be mixed and output from the unit. post-fader.
NOTE The selected button lights.
If the Mixer Mode setting is set to Multitrack, you can return Pre button: The signal is sent to the send bus before
the MON MIX slider to the center position by clicking it while adjustment by the channel fader. The send level will not
pressing the following key on the computer keyboard. be affected by the channel fader.
Windows PC: ctrl key Post button: The signal is sent to the send bus after
adjustment by the channel fader. The send level will be
Mac: command key affected by the channel fader.
2 Status display area
This shows the current status of the unit.
NOTE
If neither the pre button nor the post button is selected, no
Sample Rate: Current sampling frequency
signal will be sent to the send bus.
Sample Width: Quantization bit depth
Digital Input Status: Shows the digital input status 7 Send knob
Use to adjust the level of the signal sent to the send bus
Mixer Mode: Shows the mixer mode (send level).
3 Dynamics effects buttons Range: 0–127 (default: 0)
Click a dynamics effect button to select and use it. Use the mouse to click and drag a SEND knob up or down to
No more than two types of dynamics effects can be used at adjust the level.
a time. (The one exception is the combination of the limiter While dragging the mouse, the value being adjusted is
and low-cut filter effects.) shown beneath its SEND knob.
Options
Off (default): Effect name unlit
On: Effect name lit
TASCAM UH-7000 17
5 – Mixer Panel Settings
18 TASCAM UH-7000
5 – Mixer Panel Settings
NOTE NOTE
The buttons that can be selected depend on the Mixer Mode • The buttons that can be selected depend on the Mixer Mode
setting on the INTERFACE page. setting on the INTERFACE page.
LINE OUTPUTS Mixer Mode setting DIGITAL OUTPUTS Mixer Mode setting
SELECT buttons Multitrack Stereo Mix SELECT buttons Multitrack Stereo Mix
Master L and R Usable Usable Master L and R Usable Usable
Analog in 1 and 2 Usable Not usable Analog in 1 and 2 Usable Usable
Digital in 1 and 2 Usable Not usable Digital in 1 and 2 Usable Usable
Computer 1 and 2 Usable Not usable Computer 1 and 2 Usable Usable
Computer 3 and 4 Usable Not usable Computer 3 and 4 Usable Not usable
• If you want the output from Windows, Media Player, iTunes
u Send effects button
or another source to be output from this unit's DIGITAL
Click the REVERB button to apply the reverb effect to the
(AES/EBU) OUT jack without being affected by the mixer
stereo bus. (Default: off )
functions, set DIGITAL OUTPUTS SELECT to Computer 1 and 2.
When the send effect is on, the REVERB button lights.
a DIGITAL OUTPUTS FORMAT buttons
NOTE Use these to set the output format of the digital signals
• Turning it on will not be possible when an effect cannot be output from the DIGITAL (AES/EBU) OUT jack.
used because of sampling frequency conditions. Options: AES/EBU (default), S/PDIF
• Turning the send effect on/off using this button is linked to
the send effect on/off setting on the EFFECTS page. s Master fader
Used to adjust the level of the output signal.
i RETURN knob Use the mouse to click and drag the master fader up or
Use to adjust the return level, which is the signal from the down to adjust the master level.
send effect returned to the stereo bus. The value being adjusted is shown in the master fader level
Range: 0–127 (default: 64) display area (d).
Use the mouse to click and drag the Return knob up or
down to adjust the level. NOTE
While dragging the mouse, the value being adjusted is You can return a master fader to its 0 dB position by
shown beneath the SEND knob. clicking it while pressing the following key on the computer
keyboard.
o SEND knob Windows PC: ctrl key
Use to adjust the send level, which is the signal sent from
the send bus to the send effect. Mac: command key
Range: 0–127 (default: 127) d Master fader level display area
Use the mouse to click and drag the SEND knob up or down This shows the level of the master fader as a numerical
to adjust the level. decibel value.
While dragging the mouse, the value being adjusted is f Master level meters
shown beneath the SEND knob. The master levels are shown by this stereo level meter.
p DIGITAL OUTPUTS SELECT buttons Each level meter has an overload indicator at its top.
Use to select the signals output from the DIGITAL (AES/
EBU) OUT jack. NOTE
Options The master level meters show the levels after being adjusted
by the fader (Post fader). The level meters are affected by
Master L and R button (default):
fader adjustments and channels being muted.
Signals input through the ANALOG (BALANCED) LINE
IN 1/2 or MIC IN 1/2 jacks, through the DIGITAL (AES/
EBU) IN jacks and from the computer by USB are mixed
by the mixer and output.
Analog in 1 and 2 button:
Signals input through the ANALOG (BALANCED) LINE
IN 1/2 jacks or MIC IN 1/2 jacks are output directly.
Digital in 1 and 2 button:
Signals input through the DIGITAL (AES/EBU) IN jack
are output directly.
TASCAM UH-7000 19
5 – Mixer Panel Settings
NOTE
EFFECTS page • Turning the send effect on/off on this page is linked to the
send effect on/off setting on the MIXER page.
• Turning it on will not be possible when an effect cannot be
used because of sampling frequency conditions.
NOTE
• With one exception explained below, only one dynamics
effect can be used at a time. For this reason, if you turn on
a different dynamics effect, the dynamics effect that you
are currently using will automatically be turned off. The
exception, however, is that when the sampling frequency is
44.1 kHz or 48 kHz, both the LIMITER and LOW CUT effects
on the LIMITER/LOW CUT page can be used at the same
time. When using these two effects at the same time, the
send effect cannot be used.
• Turning the dynamics effect on/off on this page is linked to
THRESHOLD knob
the dynamics effect on/off setting on the MIXER page.
• Turning it on will not be possible when an effect cannot be Sets the threshold level that will cause the effect to start.
used because of sampling frequency conditions. Range: −32 dB–0 dB (default: −12 dB)
RATIO knob
4 Reverb type switch Sets the compression ratio for the input volume.
This unit's REVERB effect has five types.
Turning it right raises the compression ratio, increasing
Click the name of a reverb type to use it. The selected reverb the amount of compression.
type name will light.
Range: 1.0:1–inf:1 (default: 2.0:1)
For details about each parameter, see “Send effect” on page
22. ATTACK knob
Sets the amount of time until the compression reaches
5 Send effect on/off button and indicator the compression RATIO setting after the input volume
Click the name or indicator of the send effect (reverb) that is exceeds the threshold.
currently being shown to turn it on or off.
Range: 2 ms–200 ms (default: 20 ms)
When the send effect is on, its name lights.
20 TASCAM UH-7000
5 – Mixer Panel Settings
NOTE
• If the input is a stereo signal (stereo-linked channel or
master), compression will start and be applied to both
channels when either the left or right input channel exceeds FREQUENCY knob
the threshold level. Sets the lowest frequency that causes the de-esser to
• When the compressor is off, the compressor curve will function.
appear but the meters will not be active. Range: 1 kHz–4 kHz (default: 1.15 kHz)
DEPTH knob
88 Noise Suppressor
Sets the amount of compression.
When the input volume becomes less than the threshold level,
The higher the value the greater the compression (and
the output level is reduced automatically to suppress noise.
de-essing effect).
When the threshold level is exceeded, the sound is output at its
ordinary level again. Range: 1–100 (default: 25)
This is useful for reducing noise during performances and 88 EXCITER
pauses in sound input.
This effect emphasizes high-frequency harmonics to add clarity
and sparkle while maintaining the original sound.
THRESHOLD knob
Sets the threshold level that will cause the effect to start/ FREQUENCY knob
stop.
Sets the frequency above which harmonics are empha-
Range: −84 dB to −24 dB (default: −64 dB) sized.
SUPPRESSION knob Range: 1 kHz–4 kHz (default: 2.00 kHz)
Sets the amount the output level will be reduced when DEPTH knob
the input sound becomes less than the threshold level.
Sets the amount that harmonics are emphasized.
The higher the value, the more the output level and
noise will be reduced. The higher the value, the more they are emphasized.
Range: 12 dB to 72 dB (default: 42 dB) Range: 1–100 (default: 75)
ATTACK knob
Sets the amount of time until the set suppression
amount is reached after the input sound goes below the
threshold level.
Range: 0 ms–4000 ms (default: 5 ms)
RELEASE knob
Sets the amount of time until suppression stops after the
input sound exceeds the threshold level.
Range: 0 ms–4000 ms (default: 320 ms)
NOTE
If the input is a stereo signal (stereo-linked channel or
master), noise suppression will start when both the left and
right input channels go below the threshold level.
TASCAM UH-7000 21
5 – Mixer Panel Settings
FREQUENCY knob
Sets the cutoff frequency of the low-cut filter.
Options: 40 Hz, 80 Hz (default), 120 Hz
NOTE
• When the sampling frequency is 44.1 kHz or 48 kHz, both
The frequency response at the current settings is shown as a
graph even when the equalizer is off. the limiter and low-cut filter functions can be used together
at the same time. When using the limiter and low-cut filter
The equalizer has a high-shelf HIGH band, a low-shelf LOW band functions at the same time, the send effect cannot be used.
and a peaking (bell-shaped) MID band.
• The limiter can only be turned on and off. It does not have
LOW GAIN knob any adjustable parameters.
Sets the amount the level is increased or decreased for
the LOW band.
Range: ±12 dB (default: 0 dB) Send effect
LOW FREQ knob
88 REVERB
Sets the cutoff frequency of the LOW band.
This effect adds reverberations to the original sound. Multiple
Range: 32 Hz–1.6 kHz (default: 100 Hz)
sounds are delayed at various times with damping over time
MID GAIN knob that is as natural as possible to produce reverberations like
Sets the amount the level is increased or decreased for those of a hall, live-music club or studio, for example.
the MID band.
Range: ±12 dB (default: 0 dB)
MID FREQ knob
Sets the cutoff frequency of the MID band.
Range: 32 Hz–18 kHz (default: 1.0 kHz)
MID Q knob
Sets the acuteness of the peak of the MID band.
The higher the value the more acute it becomes, making
it affect a narrower frequency band. The lower the value,
the less acute it becomes, making it affect a broader
frequency band.
Range: 0.25–16 (default: 0.5) Reverb type switch
HIGH GAIN knob Use to select the type of reverb.
Sets the amount the level is increased or decreased for Depending on the type, the density and level of the
the HIGH band. reverb sound changes.
Range: ±12 dB (default: 0 dB) Options: HALL (default), ROOM, LIVE, STUDIO, PLATE
HIGH FREQ knob PRE DELAY knob
Sets the cutoff frequency of the HIGH BAND. Set the amount of delay until the first reverberations.
Range: 1.7 kHz–18 kHz (default: 10 kHz) The larger the value, the larger the reverberations make
88 Limiter/Low cut filter the room sound.
Range: 0–100 ms (default: 42 ms)
Set both the limiter and low-cut filter effects on this page.
REVERB TIME knob
The LIMITER adjusts the input gain in response to the analog
input level. This function reduces the recording level when loud Set the amount of time that the reverberations continue.
sounds are input to prevent distortion. The limiter function can The larger the value, the longer they continue.
only be used on the analog inputs. Range: 0.1–10 s (default: 2.7 s)
The LOW-CUT filter reduces the sounds of air-conditioning and
wind and other low-frequency noises that are easily picked up
by microphones.
22 TASCAM UH-7000
5 – Mixer Panel Settings
TASCAM UH-7000 23
5 – Mixer Panel Settings
NOTE NOTE
Click the “Cancel” button to return to the Mixer Panel After using this function, you can further change the
without resetting. settings as you like.
24 TASCAM UH-7000
5 – Mixer Panel Settings
Using the unit as an A/D and D/A converter Saving Mixer Panel settings to the unit
You can set the parameter values on the Mixer Panel pages to memory
values that are useful when using this unit as an A/D and D/A You can save the current Mixer Panel settings in the memory of
converter. the unit. These saved settings will be applied when the unit is
1. In the menu bar, Click “File” on a Windows PC or click used in standalone mode.
“TASCAM UH-7000 Mixer Panel” on a Mac to open a 1. In the menu bar, Click “File” on a Windows PC or click
pulldown menu, and click “ADC/DAC Preset”. “TASCAM UH-7000 Mixer Panel” on a Mac to open a
The following confirmation message will appear. pulldown menu, and click “Save”.
The following confirmation message will appear.
NOTE
After using this function, you can further change the
settings as you like.
TASCAM UH-7000 25
6 – Standalone Mode
oo DIGITAL OUTPUTS SELECT button: Master L and R
Overview
oo DIGITAL OUTPUTS FORMAT button: AES/EBU
If you turn this unit on when it is not connected to a computer
by USB, it will operate in standalone mode.
You can use this unit's A/D and D/A converters even when it is
not connected to a computer.
CAUTION
Only one set of Mixer Panel settings can be saved at a time
in the unit's memory. For this reason, saving settings to the
unit's memory will erase the previously saved settings.
NOTE
The settings used when operating in standalone mode
cannot be changed or saved without connecting a
computer.
The factory default Mixer Panel settings that are saved in the
unit's memory are as follows.
88 INTERFACE page
26 TASCAM UH-7000
7 – Application Guide
In this chapter, we explain how to set some audio applications
for use with this unit. Windows 7 and Windows Media Player
88 DAW software 1. Quit all applications and open the Control Panel from the
The ways that settings are made differ among DAWs. Start button menu.
When using a DAW, consult its operation manual. 2. Open “Sound”.
NOTE
Windows XP and Windows Media If you do not see this item, click Hardware and Sound.
Player
1. Quit all applications and open Control Panel from the Start
3. On the Playback page, right-click “Speakers TASCAM
menu.
UH-7000”, and click “Set as Default Device” in the pop-up
2. Open the “Sounds and Audio devices Properties” screen. menu that appears.
NOTE When you do this, the green check mark (4) appears next to
“Speakers TASCAM UH-7000”.
If you do not see this item, click Sounds, Speech and Audio
Services to make it appear.
NOTE
To use this unit as the recording device, open the Recording
page and use Set as Default Device for Line In TASCAM
UH-7000.
4. After completing the setting, click the OK button.
5. Start Windows Media Player, select an audio file and begin
playback.
NOTE
• If you change the setting while Windows Media Player is
running, the software will not recognize that the device has
NOTE been changed. In this case, restart Windows Media Player.
To use this unit as a recording device, set the “Sound • If you still cannot hear sound after making the settings and
recording” “Default device” to “TASCAM UH-7000”. completing the procedures above, restart the computer.
5. After completing the setting, click the OK button. • If you make this setting, sound will be output through this
6. Launch Windows Media Player, select an audio file and start unit, but no sound will be output by the computer’s speakers
playback. or headphone jack.
• By default, the mixer pan settings are set to the center (C).
NOTE For this reason, sounds playing back will be heard as mono.
• If you change the setting while Windows Media Player is Adjust the built-in mixer settings as necessary. (See “MIXER
running, the software will not recognize that the device has page” on page 17.)
been changed. In this case, restart Windows Media Player. • If you want the Windows Media Player output to be output
• If you still cannot hear sound after making the settings and from this unit's DIGITAL (AES/EBU) OUT connector without
completing the procedures above, restart the computer. being affected by the mixer functions, on the MIXER page of
• If you make this setting, sound will be output through the Mixer Panel, select the Computer 1 and 2 button in the
this unit, but no sound will be output from the computer’s DIGITAL OUTPUTS SELECT section.
speakers or headphone jack.
• By default, the mixer pan settings are set to the center (C).
For this reason, sounds playing back will be heard as mono.
Adjust the built-in mixer settings as necessary. (See “MIXER
page” on page 17.)
• If you want the Windows Media Player output to be output
from this unit's DIGITAL (AES/EBU) OUT connector without
being affected by the mixer functions, on the MIXER page of
the Mixer Panel, select the Computer 1 and 2 button in the
DIGITAL OUTPUTS SELECT section.
TASCAM UH-7000 27
7 – Application Guide
NOTE
To use this device as the recording device, select “Use this
device for sound input” for the “UH-7000’.
3. Launch iTunes, select an audio file and start playback.
NOTE
If you want the iTunes output to be output from this unit's
DIGITAL (AES/EBU) OUT connector without being affected
by the mixer functions, on the MIXER page of the Mixer
Panel, select the Computer 1 and 2 button in the DIGITAL
NOTE OUTPUTS SELECT section.
To use this unit as the recording device, open the Recording
page and use Set as Default Device for Line In TASCAM
UH-7000. Audio MIDI Setup in OS X Mavericks
5. After completing the setting, click the OK button. (10.9.1)
6. Launch Windows Media Player, select an audio file and start
playback. In OS X Mavericks (10.9.1), this unit will appear as two devices
in the Audio Devices window: “UH-7000 (Bit Accurate)” and
NOTE “UH-7000 (Core Audio)”. The “UH-7000 (Bit Accurate)” device,
• If you change the setting while Windows Media Player is however, cannot be used for input or output. Use the “UH-7000
running, the software will not recognize that the device has (Core Audio)” option.
been changed. In this case, restart Windows Media Player.
• If you still cannot hear sound after making the settings and
completing the procedures above, restart the computer.
• If you make this setting, sound will be output through
this unit, but no sound will be output from the computer’s
speakers or headphone jack.
• By default, the mixer pan settings are set to the center (C).
For this reason, sounds playing back will be heard as mono.
Adjust the built-in mixer settings as necessary. (See “MIXER
page” on page 17.)
• If you want the Windows Media Player output to be output
from this unit's DIGITAL (AES/EBU) OUT connector without
being affected by the mixer functions, on the MIXER page of NOTE
the Mixer Panel, select the Computer 1 and 2 button in the • When you can select “UH-7000 (Bit Accurate)” in a DAW or
DIGITAL OUTPUTS SELECT section. other application, it will enable recording and playback that
is even more stable.
• The “UH-7000 (Bit Accurate)” option cannot be used with
applications downloaded from the Mac App Store. For these
applications, use the “UH-7000 (Core Audio)” option.
28 TASCAM UH-7000
8 – Troubleshooting
Please read this chapter if you are unable to use the unit 88 There is no sound even when audio is playing back.
properly even after setting it up following the procedures in this
manual. e 1) When connected to a computer
If you are still unable to resolve your problems please contact The audio output must be set on the computer.
TASCAM customer support with the following information Please confirm the following while the unit is connected to
about the operating environment and details about the trouble. the computer. Moreover, if you make the following settings,
sound will be output through this unit, but no sound will be
output by the computer’s speakers or headphone jack.
88 Operating environment
Windows XP/7/8
• Computer manufacturer: Make the settings explained in Chapter 7 according to
• Model: the operating system.
• CPU: Conduct procedures 1–4 for Windows 8 or procedures
• Memory (RAM): 1–3 for Windows XP/7 to set the default device for
• playback.
Operating system:
• Applications used: Mac OS X
• Antivirus software: 1. Quit all applications and open “System Prefer-
ences…” from the Apple menu.
• Wireless LAN use:
2. Open “Sound”.
See the end of this document for contact information.
3. On the Output tab, select “UH-7000 output”.
e If you want to turn the unit on again after it has turned off
(started standby) automatically using the automatic power
saving function, press the POWER button once (turning it
off manually), wait at least eight seconds and then press the
POWER button again.
TASCAM UH-7000 29
8 – Troubleshooting
e The processing load on the computer causes sound to break e A mixer function might be affecting the volume.
up and noise to occur. Open the MIXER page of the Mixer Panel and check all the
Here are some methods to reduce the load on the computer. settings.
1) A wireless LAN and antivirus software or other
software running in the background regularly put
processing loads on the computer that can cause sound 88 Something is wrong with the sound.
to break up and noise.
e A built-in effect might be changing the sound quality.
Stop wireless LAN transmission, antivirus software and
Open the EFFECTS page of the Mixer Panel and check all the
other software running in the background when using
settings.
this unit.
2) Set the buffer size (latency) in the audio application
that you are using or in this unit's Mixer Panel to a larger 88 The volume cannot be adjusted in Audio MIDI Setup
value. (Mac).
NOTE e To adjust the input and output levels of this unit, use its
Consult the maker of the audio application that you are knobs or the controls on the MIXER page. For this reason, the
using for methods to reduce its load on your computer. volume controls for this unit in the Audio Devices window of
the Audio MIDI Setup application are disabled.
3) Change the settings of your computer so that they are
Use this unit's knobs and the faders on the MIXER page to
optimal for audio processing.
adjust the volume.
Windows 8
1. In Windows 8, right-click the ordinary start screen (Metro
user interface screen) and then click “All apps”.
2. Right-click “Computer” and select “Properties”.
3. Click “Advanced system settings”.
4. Click the “Advanced” tab.
5. Click “Settings…” in the “Performance” section.
6. In the “Visual Effects” tab of the “Performance Options”
window, select “Adjust for best performance”.
Windows 7
a) Turn Aero off.
1. Right-click the desktop and select “Personalize”.
2. Select a “Basic” or “High Contrast” theme.
b) Performance settings
1. Right-click “Computer” and select “Properties”.
2. Click “Advanced system settings”.
3. Click the “Advanced” tab.
4. Click “Settings…” in the Performance section.
5. In the “Visual Effects” tab of the “Performance
Options” window, select “Adjust for best perfor-
mance”.
Windows XP
1. Right-click “My Computer” and select “Properties”.
2. Click the “Advanced” tab.
3. Click “Settings” in the “Performance” section.
4. On the “Performance Option” screen, select “Adjust for
Best Performance”.
Mac OS X
1. Open “System Preferences…” from the Apple menu, and
select “Energy Saver”.
2. Set “Computer sleep” to “Never”.
3. Set “Display sleep” to “Never”.
NOTE
Depending on the Mac OS X version and Macintosh
computer model, this setting might not be available.
30 TASCAM UH-7000
9 – Specifications
Audio resolution Digital audio input/output ratings
88 Sampling frequencies
44.1, 48, 88.2, 96, 176.4, 192 kHz Digital input
88 Quantization bit depth 88 DIGITAL (AES/EBU) IN
24-bit Connector: XLR-3-31 equivalent (1: GND, 2: HOT, 3: COLD)
Formats: IEC 60958-3 (S/PDIF) and IEC 60958 for pro
use (AES/EBU)
Analog audio input and output ratings Sampling frequencies: ×1: 44.1/48 kHz
×2: 88.2/96 kHz
×4: 176.4/192 kHz
Analog inputs
88 Line inputs (ANALOG (BALANCED) LINE IN 1/2) Digital output
Connectors: 6.3mm (1/4") standard TRS jacks (Tip: HOT, Ring:
COLD, Sleeve: GND) 88 DIGITAL (AES/EBU) OUT
Input impedance: 15 kΩ Connector: XLR-3-32 equivalent (1: GND, 2: HOT, 3: COLD)
Maximum input level : +26.5 dBu Formats: IEC 60958-3 (S/PDIF) and IEC 60958 for pro
Minimum input level : −38 dBu use (AES/EBU)
Sampling frequencies: ×1: 44.1/48 kHz
88 Mic inputs (ANALOG (BALANCED) MIC IN 1/2)
×2: 88.2/96 kHz
Connectors: XLR-3-31 equivalent (1: GND, 2: HOT, 3: COLD) ×4: 176.4/192 kHz
Input impedance: 2.2 kΩ
Maximum input level : +2 dBu
Minimum input level : −60 dBu
Control input/output ratings
88 USB
Analog outputs
Connector: 4-pin USB B-type
88 Line outputs (ANALOG (BALANCED) OUTPUT L/R) Transfer rate: USB 2.0 HIGH SPEED (480 Mbps)/FULL SPEED
(12 Mbps)
Connectors: XLR-3-32 equivalent (1: GND, 2: HOT, 3: COLD)
Output impedance: 100 Ω
Maximum output level (INPUT knob at minimum): +24 dBu Audio performance
88 Headphones output (PHONES)
88 Audio performance
Connector: 6.3mm (1/4") standard stereo jack
Maximum output: 45 mW + 45 mW or higher (THD+N 1% or EIN: -128dBu (un-weighted), @60dB, 40Ω
less, into 32 Ω load) ADC dynamic range: 123dB(A-Weight)
DAC dynamic range: 123dB(A-Weight)
88 Frequency response
MIC Preamp: 20Hz-80kHz, +0.005dB/−0.16dB (FS=ALL)
88 S/N ratio
117dB (MICwAD)
88 Distortion
0.0009% (MIC wAD)
TASCAM UH-7000 31
9 – Specifications
CAUTION
Operation of this unit was confirmed using standard
computers that meet the above requirements. This does
not guarantee operation with all computers that meet the
above requirements. Even computers that meet the same
system requirements might have processing capabilities
that differ according to their settings and other operating
conditions
Mac OS X
88 Supported operating systems
OS X Mavericks (10.9.1 or later)
OS X Mountain Lion (10.8.4 or later)
OS X Lion (10.7.5 or later)
Mac OS X Snow Leopard (10.6.8 or later)
88 Computer hardware requirements
Apple Macintosh computer with a USB 2.0 port
88 CPU/processor speed
2 GHz or faster dual core processor
88 Memory
2 GB or more
32 TASCAM UH-7000
9 – Specifications
Dimensional drawings
233mm
214mm
81.2mm
75mm
• Illustrations in this manual might differ in part from the actual product.
• Specifications and external appearance might be changed without notification to improve the product.
TASCAM UH-7000 33
34 TASCAM
88 Multitrack mode
UH-7000
Audio flow diagram
88 Stereo mix mode
TASCAM UH-7000
35
9 – Specifications
UH-7000