Professional Documents
Culture Documents
3412E Engine Data Cam Shaft Assembly and Disassembly
3412E Engine Data Cam Shaft Assembly and Disassembly
3412E Engine Data Cam Shaft Assembly and Disassembly
Shutdown SIS
Previous Screen
SENR10630045
Camshaft
SMCS - 1210-011; 1210-012
Remove Camshaft
Start By:
supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of fluids
according to local regulations and mandates.
1. Turn the engine with Tool (A) until the bolts in camshaft rear gear (1) are visible.
Remove the four bolts. Pull gear (1) loose from the camshaft.
2. Turn the engine with Tool (A) until the "V" marks on the front of the timing gears are in
alignment. Install Tool (B) through gear (1) into the camshaft.
4. Pull camshaft assembly (2) approximately 50.8 mm (2.00 in) out of the cylinder block.
5. Fasten gear (1) to the flywheel housing with wire. Remove Tool (B) and remove gear (1).
NOTICE
When Tool (B) is removed the rear camshaft
gear is free to fall into the flywheel housing. If
the gear falls into the flywheel housing the
flywheel housing must be removed to remove
the gear.
NOTICE
Be careful not to damage the camshaft bearings
or the camshaft journals as the camshaft is
https://s1.remotelab.space:501/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.js… 2/5
3/8/2020 3412E Industrial Engine 4CR00001-UP(SEBP2510 - 68) - Systems & Components
removed.
7. If necessary, remove the camshaft gear with Tool (D). Remove the dowel on the taper
end of the camshaft with Tooling (C).
Install Camshaft
1. Heat gear (1) to a maximum temperature of 205°C (400°F). Install gear (1) on camshaft
(2).
NOTE: Make sure the key for gear (1) is in position on camshaft (2) before gear (1) is
installed.
2. Install pin (3) until it is extended 8.76 ± 0.25 mm (.345 ± .011 in) from the end of the
camshaft.
https://s1.remotelab.space:501/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.js… 3/5
3/8/2020 3412E Industrial Engine 4CR00001-UP(SEBP2510 - 68) - Systems & Components
3. Put 2P-2506 Anti-Seize Compound on the camshaft lobes and valve lifter rollers. Put
clean engine oil on the bearing journals of the camshaft.
4. Install the camshaft until the rear of the camshaft is even with the rear of the cylinder
block.
5. Fasten a safety wire to the rear camshaft gear. Put the gear in position and use Tool (B) to
hold it.
6. Make an alignment of the "V" mark on gear (1) with "V" mark on gear (5) and install the
camshaft all the way in the cylinder block.
8. Make an alignment of the dowel in the rear of the camshaft with the dowel hole in
camshaft rear gear (6). Remove Tool (B) and the safety wire.
9. Turn the engine with Tool (A) and install the bolts to hold gear (6).
NOTE: Because of the position of the bolts the torque on the bolts must be checked three
times.
NOTE: For more detailed information regarding the camshaft, see the topic "Camshaft" in
the Specifications Module.
End By:
https://s1.remotelab.space:501/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.js… 4/5
3/8/2020 3412E Industrial Engine 4CR00001-UP(SEBP2510 - 68) - Systems & Components
Copyright 1993 - 2020 Caterpillar Inc. Sun Mar 08 2020 07:33:08 GMT+0200 (Eastern
All Rights Reserved. European Standard Time)
Private Network For SIS Licensees.
https://s1.remotelab.space:501/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.js… 5/5