PARTICULAR MATERIAL APPRAISAL
VY (PRESSURE EQUIPMENT DIRECTIVE-2014/68/EU)
Pressure Equipment Manufacturer: VRV ASIA PACIFIC PVT LTD
| PMA Ref. No. : VRV/CE/01. [Rev.No. 02 Material Group & Sub Group: 8 & 8.1
Material specification:
EAMES FGA ELIOT Grade: F304 Delivery condition: Solution Annealed
Dimension range :
Applicable Design Code: EN 13458-2 Annex C 8mm to 6 168.3mm
Wall thickness : 2 mm to 40 mm
Application: Detail Comments
Vessel V | Type : Cryogenic Vessel
Piping ~ | (Nozzles, flanges, couplings
Equipment Pressure and plugs)
Accessories 5
_ Assembly
Gas
Liquid e
Fie Group 1 v
Group 2
1
Category }
ti
Vv v
| Operating Conditions: Details ‘Comments
Maximum Allowable Working Pressure (bar) | 17/18/23/24/36/37
‘Allowable Temperature Range °C 196° C to 50°C
‘And where ever relevant
corrosion =
ageing =
Formability =
weldability Suitable for welding
machinability Suitable for machining
C Specific Requirements - :
Property Requirement Specification Comments
Min. Yield strength 205 Mpa From ASME Sec,il,Part D
Strength governs the allowable stress
Min. Tensile strength _| 515 Mpa and meets the requirement
Toughness at Lowest Impact test is exempted as
Toughness operating temperature | Not required per G-17 PED Guidelines
196°C
Ductility 149% minimum 30% Meets the requirement
earmakitay Suitable for machining | Suitable for machining and | s.54< the requirement
and welding welding
Sowabsee From ASME Sec,l,Part D
136.66 Mpa 138 Mpa governs the allowable stress
- and meets the requirement
Wik Page tof 2
NeARTICULAR MATERIAL APPRAISAL
(PRESSURE EQUIPMENT DIRECTIVE-2014/68/EU)
Pressure Equipment Manufacturer: VRV ASIA PACIFIC PVT LTD
PMA Ref. No. : VRV/CE/01 Rev.No. 02 Material Group & Sub Group: 8 & 8.1
Material specification:
SA 182 F 304 Ed 2017
Grade: F304 Delivery condition: Solution Annealed
Dimension range
Applicable Design Code: EN 13458-2 Annex C Diameter : 8mm to 9 168.3mm
Wall thickness : 2 mm to 40 mm
Conditions
In Addition to the requirements of the above specification each batch of material used in this application shall
be covered by a certificate of specific material control as evidence of conformity with the following
requirements
Property Requirement Test method Specification) | Comment
chenial C-0.08%,Nin-2.00%,P-
sine 0.045%,5-0.03%, Si- SA751
Composition
196,Ni-B-11%6,Cr-18-20%
Tensile Strength-
Mecha
Mechanical | s1sMpaieldstrength- | SA370
ia 205Mpa;Elongation-30%
Certification according to 7
Material EN 10204:2008 . oo
Certification __| Inspection Certificate O
minimum “type 3.1" Certificate “type 3.1
Manufacturer name or trade
mark ,size, material
specification Drawing No
_| and Lot no.
Traceability to heat/lot
Material Marking | identity of the material | --
manufacturer
The above material has been appraised for compliance with the essential safety requirements of the PED for
the above application and has been granted a Particular Material Appraisal subject to the conditions listed.
Revisions to the parent specification, by the issuing authority, are to be reviewed by the manufacturer, and
where applicable advised to the notified body, and may result in invalidation of this PMA
HOE. he
(Pressure Equipment Manufacturer)
Signed: Date: 26/guly 201?
Confirmed: Date:
Notified Body (Cats II & IV only)
Page 2 of