Professional Documents
Culture Documents
LC Grafico 128X64 PDF
LC Grafico 128X64 PDF
DATA SHEET
A
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
CONTENTS
1. SCOPE -------------------- 3
3. RELIABILITY -------------------- 9
5. NOTES -------------------- 18
Preliminary
02/09/13 2 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
1. SCOPE
This specification covers the engineering requirements for the
G128641BNHDWB liquid crystal module.
2. PRODUCT SPECIFICATIONS
2.1 General
z 128 × 64 dot matrix LCD
z STN (Blue mode) , Negative mode LCD panel
z Transmissive , Wide temperature type
z 6 o’clock
z Back-light : Edge LED , White
z Multiplexing driving : 1/64duty, 1/9bias
Item Characteristic
Preliminary
02/09/13 3 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
[ VSS=0V ]
Item Symbol Min. Max. Unit Note
Supply Voltage VDD -0.3 7.0 V
Input voltage (Signal) VI -0.3 VDD+0.3 V
Operating temperature TOP -20 70 °C
Storage temperature TSTG -30 80 °C
Humidity -- -- 90 %RH 1)
Note 1) Referenced to VSS=0V
DC CHARACTERISTICS
TEST CONDITIONS(Unless otherwise noted, VSS=0V, VDD=5.0V±10%,Ta=-20 to 70°C
TEST PIN
ITEM SYMBOL MIN TYP MAX UNIT
CONDITIONS NAME
Operating Voltage VDD -- 4.5 5.5 5.5 V VDD
H Level VIH -- VDD-2.2 -- V Input pins
Input
L Level VIL -- 0 -- V Input pins
Output
H Level VOH -- VDD-0.3 -- V
Output pins
Voltage Output
L Level VOL -- 0 -- V
pins
Output
Output H Level ROH VOUT=VDD-0.5V -- -- Ω
pins
Resistanc
e Output
L Level ROL VOUT=0.5V -- -- Ω
pins
Input Pull-up
RPU -- 50 100 kΩ (Note 1)
Resistance
Operating Frequency fOSC -- 0.4 -- MHz
Preliminary
02/09/13 4 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Preliminary
02/09/13 5 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Y' ( φ = 180 ο) X ( φ = 90 ο)
φ
X'
LC panel Y ( φ = 0 ο)
( θ = 90 ο)
Z
Light (When transmitted)
*Definition of contrast C
B1 Brightness of selected portion
C= =
B 2 Brightness of unselected portion
(%)
Dark
unselected portion brightness curve
(bias voltage applied)
Brightness
selected portion
brightness curve
Bright
Preliminary
02/09/13 6 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Cmax.
Contr ast C
2.0
θ1 θ2 Viewing angle θ
( φ fixed)
Note : Optimum vision with the naked eye and viewing angle θ at Cmax
above are not always the same.
V opr
Voltage
0
(V)
10%
Dark
90%
Brightness 100%
Bright
t on t off
Preliminary
Vop : Operating voltage (V) ton : Response time (rise) (ms)
fFRM : Frame frequency (Hz) toff : Response time (fall) (ms)
02/09/13 7 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
If=80mA,
Forward voltage Vf 3.3 3.4 3.5 V
White
If=80mA,
*Luminous Intensity IV -- 200 -- cd/m2
White
If=80mA,
Luminous Tolerance -- -- -- 20 %
White
VR=5V,
Reverse Current IR -- -- -- mA
White
X If=80mA, -- 0.31 --
Chromaticity --
White
Y -- 0.32 --
Reverse Voltage VR 5 V
Preliminary
02/09/13 8 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
3. RELIABILITY
3.1 Reliability
Test item Test condition Evaluation and assessment
Preliminary
02/09/13 9 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
4. OPERATING INSTRUCTIONS
1 FG Frame ground
8 C/D Code/Data
18 FS Font select
Preliminary
02/09/13 10 / 19
11 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
/WR
LCD Panel
Preliminary
/RD Controller Common
/CE 64
Driver (Dot Matrix 128 x 64 dots)
C/D
/RST LSI
MODEL NO: G128641BNHDWB
DB0~DB7 S-RAM
64 64
FS
T6963C
VCC
Segment Segment
VLCD Crystal Driver Driver
VSS
02/09/13
FG
4.2 Circuit Block Diagram
LEDA
BACKLIGHT
LEDK
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
+5V
VCC
VCC
VCC-VLCD
LCM
VLCD VR VEE
Vss
GND
VCC – VLCD : LCD Driving Voltage
VR : 10K~20K
LEDA (+)
LED Back-light
LEDK (-)
Preliminary
02/09/13 12 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Preliminary
02/09/13 13 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Preliminary
02/09/13 14 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Preliminary
02/09/13 15 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
Preliminary
02/09/13 16 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
X: invalid
Preliminary
02/09/13 17 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
5. NOTES
Safety
z If the LCD panel breaks, be careful not to get the liquid crystal in your
mouth. If the liquid crystal touches your skin or clothes, wash it off
immediately using soap and plenty of water.
Handling
z Avoid static electricity as this can damage the CMOS LSI.
z The LCD panel is plate glass; do not hit or crush it.
z Do not remove the panel or frame from the module.
z The polarizing plate of the display is very fragile; handle it very carefully
Mounting and Design
z Mount the module by using the specified mounting part and holes.
z To protect the module from external pressure, leave a small gap by placing
transparent plates (e.g. acrylic or glass ) on the display surface, frame, and
polarizing plate
z Design the system so that no input signal is given unless the power-supply
voltage is applied.
z Keep the module dry. Avoid condensation, otherwise the transparent
electrodes may break.
Storage
z Store the module in a dark place where the temperature is 25 oC±10 oC and
the humidity below 65% RH.
z Do not store the module near organic solvents or corrosive gases.
z Do not crush, shake, or jolt the module (including accessories).
Cleaning
z Do not wipe the polarizing plate with a dry cloth, as it may scratch the
surface.
z Wipe the module gently with soft cloth soaked with a petroleum benzine.
z Do not use ketonic solvents (ketone and acetoe) or aromatic solvents
(toluene and xylene), as they may damage the polarizing plate.
6. OPERATION PRECAUTIONS
Any changes that need to be made in this specification or any problems arising
from it will be dealt with quickly by discussion between both companies.
Preliminary
02/09/13 18 / 19
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: G128641BNHDWB
7. LCM Dimension
Preliminary
02/09/13 19 / 19