IPL PRO Device Interface Communication Sheet

You might also like

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

smsg_39_1840_v1_2_1.

pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

This document provides additional assistance with wiring your Extron IPL PRO enabled product to your device.
Different components may require a different wiring scheme than those listed below.

For complete operating instruction, refer to the user's manual for the specific Extron IPL PRO enabled product or
the controlled device manufacturer supplied documentation.

Device Specifications:

Device Type: Touch Display


Manufacturer: Samsung
Firmware Version: N/A
Model(s): DM82E-BR, DM75E-BR, DM65E-BR, DM82E-BM

Tested on the Following Software and Firmware Versions:

IP Link Pro Control Processor


MediaLink Plus Controller Firmware GC (Plus, Pro) Version
Firmware

2.06.0002-b002 2.02.0000-b003 2.7.1.88

Version History

Driver Version Date Notes

1_2_1 2/5/2018 Added model DM82E-BM

Added commands: Aspect Ratio, Audio Mute, Screen Mode and Screen
1_2_0 3/22/2017
Size.

1_0_1 6/8/2016 Added Input IWB

1_0_0 12/23/2015 Initial Version

Driver Notes:
• User Defined command takes a string parameter and sends the string out of the port.
• Only Power Command will be sent to the device when it is Off.
• Device ID needs to match the ID on the Display and is defaulted to 1.
• When Device ID is set to ‘Broadcast’, status is unavailable as the driver becomes unidirectional.

Page 1 of 6
A
smsg_39_1840_v1_2_1.pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

Driver Timings:
• Recommended repeat rate for this driver is .1 seconds.

Page 2 of 6
A
smsg_39_1840_v1_2_1.pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

Control Commands & States:

Aspect Ratio 2 Auto Wide 16:9 Zoom


Zoom 1 Zoom 2 Just Scan
4:3 Wide Fit Custom
Smart View 1 Smart View 2 Wide Zoom
21:9 16:9 (PC) 4:3 (PC)
21:9 (PC) Original Ratio (PC)
Audio Mute On Off
Auto Image None
Executive Mode On Off
Input PC DVI MagicInfo
AV DTV DisplayPort
HDMI 1 HDMI 2 Component
IWB
PIP Mode 1 On Off
Power On Off
Screen Mode 2 16:9 Zoom 4:3
Wide Zoom
User Defined Command None
User Defined String String
Video Wall On Off
Video Wall Mode Full Natural
Volume 0 to 100 in steps of 1
1
The mode cannot be controlled if Video Wall is set to “On” and this function is not available in MagicInfo.
2
The mode cannot be controlled if Video Wall is set to “On” and some values are not supported based on input
values.

Page 3 of 6
A
smsg_39_1840_v1_2_1.pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

Status Available:

Aspect Ratio Auto Wide 16:9 Zoom


Zoom 1 Zoom 2 Just Scan
4:3 Wide Fit Custom
Smart View 1 Smart View 2 Wide Zoom
21:9 16:9 (PC) 4:3 (PC)
21:9 (PC) Original Ratio (PC)
Audio Mute On Off
Connection Status RP Connected Disconnected
Executive Mode On Off
Input PC DVI MagicInfo
AV DTV DisplayPort
DVI - VIDEO HDMI 1 PC HDMI 2 PC
HDMI 1 HDMI 2 Component
IWB
PIP Mode On Off
Power On Off
Screen Mode 16:9 Zoom 4:3
Wide Zoom
Screen Size 0 - 255 Inch
User Defined String String
Video Wall On Off
Video Wall Mode Full Natural
Volume 0 to 100 in steps of 1
RP
Connection Status is based off of the following string: \xAA\x11\xYY\x00\xZZ (where YY is the Device ID
number and ZZ is checksum value)

Page 4 of 6
A
smsg_39_1840_v1_2_1.pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

Cable and Adapter Requirements:


Captive Screw to 3.5mm stereo RS-232 Serial Cable

Notes for the Device:

Serial communication:

Port Type: RS-232 Parity: None


Baud Rate: 9600 Stop Bits: One
Data Bits: 8 Flow Control: None

Pin Assignments Diagram

General Notes:

Page 5 of 6
A
smsg_39_1840_v1_2_1.pkp
IPL PRO Device Interface Revision: 2/5/2018
Communication Sheet

Network communication:
When configuring the Ethernet driver, be sure device settings match that of the GCP configuration.

Port Type: Ethernet


Default Port: 1515
Logon Credentials No
Supported:
Multi-Connection Undetermined
Capabilities:
Port Changeability: Yes

Ethernet Driver Configuration Description:


Please refer to user manual for settings and changes to the network communication

Notes for the Device:

Page 6 of 6
A

You might also like