Professional Documents
Culture Documents
Arc 2019-2020
Arc 2019-2020
Arc 2019-2020
CHAPTER-14 FABRICATION 49 27
CHAPTER-19 (A) SUPPLY OF MATERIAL FOR KUTIR JYOTI/BPL CONNECTION IN RURAL AREA 76 27
CHAPTER-22 LABOUR 88 27
CHAPTER-23(A) HIRE CHARGES OF PLANTS AND MACHINERIES WITH EXCLUDING FUEL 90 Under
Considera
tion
CHAPTER-23(B) HIRE CHARGES OF PLANTS AND MACHINERIES WITH INCLUDING FUEL 95 Under
Considera
tion
CHAPTER-24 REPLACEMENT OF 11 KV CT PT SETS 96 27
1.3.2 Levelling of ground above 30 cm.to 90 CM.depth. with tractor and T&P Sq.Mtr 6.87
required as per condition of ground including removal of rubbish plants
from ground & marking of boundary with lime powder.(Including all lead &
lifting)
1.4 Trimming of tree branches/plants and preparing route approchases for Per 30.57
proposed line. tree/plant
NOTE: The rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra
by Nigam if applicable.
[1]
CHAPTER NO.2
EARTH WORKS INCLUDING FOUNDATION ACTIVITIES
Chapter DESCRIPTION OF WORK UNIT Rate /Unit
Code No
1 2 3 4
2.1 Excavation of pit in soil (ordinary) to erect various supports and stay sets
including stacking of excavated soil from the edge of excavation.
(A) Height of poles/R.S.Joist/M.S. Rail Size of pit
2.1.1 8 Mtr/R.S.Joist/M.S. Rail 1.2mx0.6mx1.35 m deep Pit 88.97
2.1.2 9 Mtr/ 1.2mx0.6mx1.50 m deep Pit 94.81
2.1.3 10/11 Mtr/ 1.2mx0.6mx1.65 m deep Pit 100.81
(B) Lattice Tower /Size of pit
2.1.7 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep Pit 311.13
2.1.8 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep Pit 328.84
(C)Stay set/Depth of pit
2.1.9 8'x 3/4" -0.75x0.5x1.6 m Pit 74.12
2.1.10 6'x 5/8" -0.75x0.5x1.35 m Pit 65.10
2.2 Excavation of pit in Hard soil
(A) Height of poles/R.S.Joist/M.S. Rail Size of pit
2.2.1 8 Mtr/R.S.Joist/M.S. Rail 1.2mx0.6mx1.35 m deep Pit 97.81
2.2.2 9 Mtr/ 1.2mx0.6mx1.50 m deep Pit 104.29
2.2.3 10/11 Mtr/ 1.2mx0.6mx1.65 m deep Pit 110.78
(B) Lattice Tower /Size of pit
2.2.7 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep Pit 342.26
2.2.8 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep Pit 361.85
(C)Stay set/Depth of pit
2.2.9 8'x 3/4" -0.75x0.5x1.6 m Pit 81.53
2.2.10 6'x 5/8" -0.75x0.5x1.35 m Pit 71.74
2.3 Excavation of pit in ordinary rock which does not require blasting to erect
various supports and stay sets including stacking of excavated muck from
the edge of excavation/pit.
(A) Height of poles/R.S.Joist/M.S. Rail /Size of pit
2.3.1 8 Mtr/R.S.Joist/M.S. Rail 1.2mx0.6mx1.35 m deep Pit 245.87
2.3.2 9 Mtr/ 1.2mx0.6mx1.50 m deep Pit 260.73
2.3.3 10/11 Mtr/ 1.2mx0.6mx1.65 m deep Pit 278.42
(B) Lattice Tower /Size of pit
2.3.4 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep Pit 1336.17
2.3.5 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep Pit 1596.90
[2]
Chapter DESCRIPTION OF WORK UNIT Rate /Unit
Code No
1 2 3 4
(C)Stay set/Depth of pit
2.3.6 8'x 3/4" -0.75x0.5x1.6 m Pit 237.02
2.3.7 6'x 5/8" -0.75x0.5x1.35 m Pit 213.31
2.4 Excavation of pit in Hard rock ( Where blasting is required) to erect various
supports and stay sets including stacking of excavated muck from the edge
of excavation/pit.
Note
1 The rates are all lead of cement,lime,ballast, sand,surkhi and grit etc.at site
of work.
2 For all concrete work coarse sand shall be used no extra will be paid .
3 Concrete mix prepared by power driven mechanical mixer shall be used .
4 Under exceptional coditions, where mechanical mixer and vibrator are not
used(with the approval of Engineer Incharge reduced by 3% for mechanical
mixer and 2% for Vibrator
Note
1 The rates for complete work including racking of
joints,curing,grinding,mixing and finishing T&P and scaffolding material and
cost of material with all lead and lift.
2 The rates cover protection of all place and things,requiring protection and
cleaing such places and thing of all droppings and splashes of mortar etc.
2.8 Cement concrete flooring grade 1:2:4 (1-cement :2- coarse sand :4-graded
stone aggregate ) rounding off edges etc.but excluding cost of nosing of
steps etc. complete.
2.8.1 25 mm thick with 12.5 mm thick nominal size aggregate. SqM 170.66
2.8.2 75 mm thick with 20 mm thick nominal size aggregate. SqM 406.73
Note
1 The rates for all items inculde all form of work , laying ,curing and finishing
etc. The rates are for complete work at site, inclusive of all leads.
2 The rates cover the preparation and cleaing of all places
2.9 Providing and fixing of reinforced ferro cement drain cover designed for
Class -A leading duly marked on cover with adequate steel reinforced
cement having thickness 75 mm to 150 mm with anti corrosive bitumen
painted M.S. plate , Rim and M.S. lifting hooks addmixture like plasticizer
bond improving compound , shrinking resistance compound abrasion
resistant complete as per approved design etc with span 300 to 450 mm
and standard size 600x800 mm ( when trench is working as a culvert).
2 In case of non availability of stone header of proper size cement concrete header of mix
1:3:6(M-10) with 25 mm graded stone aggregate with smooth finish may be provided by
the contractor at no extra cost.
3 The rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
[4]
CHAPTER NO.3
TRANSPORTATION OF MATERIAL
Chapter
DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
3.1 Safe carriage of PCC poles including loading / un-loading
a) 9 Mtr. Long-400 Kg /11 Mtr. PCC pole
3.1.1 Within 10 Kms. Pole 236.27
3.1.2 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. Pole 4.84
3.1.3 Above 30 Kms. Add for each Kms. or part thereof. Pole 2.49
b) 8 Mtr. Long PCC pole
3.1.4 Within 10 Kms. Pole 160.70
3.1.5 Above 10 Kms. & upto 30 Kms. Add for each Km. or part thereof. Pole 4.84
3.1.6 Above 30 Kms. Add for each Kms. or part thereof Pole 2.49
c) 9 Mtr.long 200 Kg. PCC pole
3.1.7 within 10 Kms.- Pole 198.27
3.1.8 Above 10 Km. & upto 30 Km. add for each Km. or part thereof Pole 4.84
3.1.9 Above 30 Km. add for each Km. or part thereof Pole 2.49
3.2 Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails,
R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay
Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading
and unloading and stacking in Nigam store /at work site
3.2.1 Within 10 Kms. M.T. 332.02
3.2.2 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. M.T. 4.70
3.2.3 Above 30 Kms. Add for each Kms. or partthereof. M.T. 2.91
3.3 Safe Carriage of insulator, hardware, cable etc.including
loading/unloading and stacking in Nigam.stores etc.
3.3.1 Within 10 Kms. M.T. 397.93
3.3.2 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. M.T. 5.67
3.3.3 Above 30 Kms. Add for each Kms. or part thereof. M.T. 3.59
3.4 Safe carriage of fabricated lattice towers structures and sub-station
structures type AB, AB beams, isolators structures etc. including
loading/unloading and stacking in the Nigam. Stores / at work site.
[6]
Chapter
Code No DESCRIPTION OF WORK UNIT Rate/Unit
1 2 3 4
c) 5.0 MVA
3.9.9 Within 10 Kms Nos. 5181.28
3.9.10 Above 10 Kms & upto 30 Kms . Add for each Km or part thereof Nos. 51.81
3.9.11 Above 30 Kms & upto 50 Kms . Add for each Km or part thereof Nos. 34.27
3.9.12 Above 50 Kms . Add for each Km or part thereof Nos. 16.58
3.10 Safe carriage of transformer from stores to stores( upto 100 KVA three
phase/upto 25 KVA single phase.)
3.10.1 Within 10 KMs. Nos. 138.86
3.10.2 Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof Nos. 4.43
3.10.3 Above 30 Kms. and upto 50 Kms.Add per each km,or part thereof Nos. 3.59
3.10.4 Above 50 Kms.Add per each km,or part thereof Nos. 2.62
3.11 Safe carriage of transformers from stores to stores(Above 100 KVA
and upto 500 KVA)
3.11.1 Within 10 KMs. Nos. 207.25
3.11.2 Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof Nos. 6.63
3.11.3 Above 30 Kms. and upto 50 Kms.Add per each km,or part thereof Nos. 5.25
3.11.4 Above 50 Kms.Add per each km,or part thereof Nos. 4.01
3.12 Safe carriage of breakers/kiosks etc. including loading/ unloading and
stacking in Nigam stores
3.12.1 Within 10 KMs. Nos. 907.06
3.12.2 Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof Nos. 11.74
3.12.3 Above 30 Kms. and upto 50 Kms.Add per each km,or part thereof Nos. 9.39
3.12.4 Above 50 Kms.Add per each km,or part thereof Nos. 7.05
3.13 Safe carriage of panels including loading/ unloading and stacking in
Nigam stores
3.13.1 Within 10 KMs. Nos. 725.65
3.13.2 Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof Nos. 9.39
3.13.3 Above 30 Kms. and upto 50 Kms.Add per each km,or part thereof Nos. 7.46
3.13.4 Above 50 Kms.Add per each km,or part thereof Nos. 5.53
3.14 Safe Carriage of 33/11 KV Power Transformer
3.14.1 8.0 MVA Nos.
3.14.2 Within 10 Kms Nos. 6525.62
3.14.3 Above 10 Kms & upto 30 Kms . Add for each Km or part thereof Kms. 65.25
3.14.4 Above 30 Kms & upto 50 Kms . Add for each Km or part thereof Kms. 42.79
3.14.5 Above 50 Kms . Add for each Km or part thereof Kms. 19.93
Transportation of Single phase Sub-Station Structure from sub-division Per 322.00
store to the site & Erect it on the existing pole at a height of 5 Mtr. From the Struct
3.15 ground level ure
Note:
1 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
2 Above Charges will be 1.5 times for both sides for the items 3.5 & 3.6.
1 2 3 4
4.1 Safe loading of steel fabricated / unfabricated conductor drum & M.T. 224.86
other line material.
4.2 Safe loading of power/ distribution transformer.
(A) 33/11 KV power transformer.
4.2.1 Upto 1.6 MVA Nos. 3240.32
4.2.2 Above 1.6 MVA & upto 3.15 MVA Nos. 3914.48
4.2.3 Above 3.15 MVA Nos. 5134.28
4.2.4 Above 5 MVA Nos. 7828.96
(B) 11/.4 KV Distribution Transformer
4.2.4 10 & 16 KVA Nos. 99.67
4.2.5 25 & 40 KVA Nos. 126.10
4.2.6 Above 40 KVA & upto 100 KVA Nos. 169.60
4.2.7 Above 100 KVA & upto 315 KVA Nos. 295.70
4.2.8 Above 315 KVA Nos. 635.05
(C ) 6.35/0.24 KV Transformer
4.2.9 25 KVA Nos. 126.10
4.2.10 Upto 16 KVA Nos. 87.59
4.3 Safe unloading of steel fabricated/ unfabricated conductor drum & M.T. 110.84
other line material.
4.3.1 Safe unloading of power/distribution transformers
a) 33/11 KV power transformer.
4.3.2 Upto 1.6 MVA Nos. 2620.52
4.3.3 Above 1.6 MVA & upto 3.15 MVA Nos. 3288.21
4.3.4 Above 3.15 MVA Nos. 4349.42
b) 11/.4 KV Distribution Transformer
4.3.5 10 & 16 KVA Nos. 45.31
4.3.6 25 & 40 KVA Nos. 56.18
4.3.7 Above 40 KVA & upto 100 KVA Nos. 86.85
4.3.8 Above 100 KVA & upto 315 KVA Nos. 242.70
4.3.9 Above 315 KVA Nos. 500.78
(c ) 6.35/0.24 KV Transformer
NOTE:- The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
[9]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code Unit
No
1 2 3 4
5.5 Erection & fixing of steel struts in the excavated pit in position.The top end of the
strut will be properly holed/welded with the main support muffed in cement
concrete of ratio 1:3:6 as per item No.5.7.The nuts and bolts will be provided by
the contractor as per Nigams specification for which payment will be made at the
prevailing store issue rate.The cost of muffing and grouting will be paid extra.
5.7 Supplying and laying of randum rubble stone boulder having weight not less than CUM 471.83
20 kgs.
5.8 Fixing of all type of fabricated material on erected supports with nut & bolts as per MT. 3221.91
approved design & drawing of sub-station.
NOTE:-
1 The approved design of cement concrete work will be given by the AEn./Incharge of the works.
2 The payment of cement concrete work as per accurate measurement will be made in addition to
the work of support erection.
3 The rates are inclusive of all the material such as river send stone grit,water and T&P etc.unless
otherwise specified.
4 The quality of cement and other material shall be got checked and approved by the AEN.
Incharge,
5 The cement shall be supplied departmentally if avaiable otherwise contractor will have to arrange
the same at his level.
6 If the stay required to be grouted in cement then the rates as indicated in item 5.7 will be
applicable& paid in addition to above rates and the charges for back filling with soil will be
deducted @ 10.00 per cum.
7 If stay insulator is not availabe with the Nigam. Then the contractor will have to provide the same
as per Nigams Specification for which he will be paid in accordance with Prevailing Discom store
issue rates
8 Dismantling charges for all the items will be 60% of item Rates of erection charges . However
charges for transportation of the materialfrom works site in the sub-division store shall be paid
as item rate of chapter III (transportation of material).The payment will be made after issuance of
certificate by the AEn.concerned that all the dismantled material has been safely received in the
sub-divisional store.
9 The nuts and bolts will be privided/supplied by the contractor which will confirm to relevant ISS.
10 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra
by Nigam if applicable.
[10]
CHAPTER-6
ASSEMBLY & INSTALLATION OF VARIOUS ITEMS
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
6.1 Fixing of cross arms with clamp on erected support as per design. The nuts
&bolts will be supplied by the contractor as per Nigams specification for
which payment will be made as per prevailing Discom store issue rates.
6.6 Fixing of fabricated cantilever breacket on erected support as per design. Nos. 58.00
The nuts&bolts will be supplied by the contractor as per Nigams
specification for which payment will be made as per prevailing Discom store
issue rates,
6.7 Fixing and assembly of disc.point channel pair with pilot plates&clamps on
erected double pole structure as per design. The nuts &bolts are to be
provided by the contractor as per Nigams specification for which payment
will be made as per prevailing Discom store issue rates.
[11]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
6.8 Fixing and assembly of disc.point channel pair with pilot plates top hampers
& clamps on erected single pole structure as per design. The nuts &bolts
are to be provided by the contractor as per Nigams specification for which
payment will be made as per prevailing Discom store issue rates,
[12]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
6.19 Installation of lightening arrestors on erected structure /support (set of 3
nos) including connection with earth by wire /strip as required and
jumpering etc. The nuts & boltswill be supplied by the contractor for which
payment will be made as per prevailing Discom store issue rates,
(A)sub-station type
6.19.1 33 KV L.A. set Set 174.29
6.19.2 11 KV L.A. set Set 151.22
(B)pole mounted type
6.19.3 11 KV L.A. set Set 42.83
6.20 Installation testing as per Nigams norm & commissioning of 11/0.4KV
distribution transformer on erected supports including fixing of base
channels as per requirment jumpering on HV&LV side, crimping of lugs/
clamping earth connections of body and neutral of transformer with wire
/strip (as already provided with earthing ) complete in all respect. The PG
clamps nuts & bolts will be supplied by the contractor for which payment
will be made as per prevailing Discom store issue rates,
[13]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
[14]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
6.28 (a) Fixing of PG clamp of Weasel /Rabbit Conductor Nos. 5.06
(b) Fixing of PG clamp of Dog /Racoon Conductor Nos. 5.06
( c) Fixing of PG clamp of Panther Conductor Nos. 8.06
6.29 Fixing of metering cum protection box on LT side of distribution transformer Nos. 40.30
at stores
6.30 Fixing of LT capacitors in metering cum protection box on LT side of Nos. 50.42
distribution transformer at site.
6.31 Tag Welding of Nuts and Bolts(with sealing bolts) at different 5 to 6 places Nos. 52.15
at welded strips already provided on M&P boxes fitted on 11/0.4 KV 3
phase 25/40/63 KVA transformers as per latest drawing and design of
Nigam in the stores for which adequate space and electricity will be
provided by Nigam and handling of tranformer will be done by Nigam.
6.32 Welding of door(s)(continuous welding of patties and tag welding of Nuts & Nos. 434.54
Bolts with sealing bolt ) of M&P box fitted on 11/0.4 KV,3 phase 25/40/63
KVA transformers at 5 to 6 places with two nos. patties at site(one made of
flat size 75x30x5 mm or 75x40x5 mm and other patti made of flat size
55x30x5 mm or 55x40x5 mm. These two patties will form one pair. Patti of
size 75x30x5 mm /75x40x5 mm is to be welded on side of the box and
other patti of size 55x30x5 mm or 55x40x5 mm is to be welded on door of
the box to form locking arrangement through Nuts & Bolts(size 1/2"x1 1/2")
as per latest drawinf and design of nigam.Patties and Nuts & Bolts will be
provided by Nigam.
6.33 Welding of single phase transformer(s)with base of transformer welded with Nos. 434.54
substation structure at four points.Tag welding of all bolts & nuts of
subatation structure,upper ring of transformer(s)and continuous welding of
upper lid of transformer at three places of 2" siz including material.In case
base of transformer with sub station structure and lid of transformer with
ring is welded with piecec of flat iron then the flat iron would be provided by
the Nigam.
6.34 Making Push-Fit type arrangement insheet metal single phase and three Nos. 26.08
phase meter boxes.
6.35 Assembly,installation & commisioning of 11 KV Roaster switchs on erected Nos. 1651.25
structures with stting for accurate operation including fixing of allied
accessories completed in all respect with post insulators and jumpering on
both ends for connection with systm.The nuts & bolts will be supplied by
contractor for which payment will be made as per prevailing Dicom store
issue rates.
6.36 Assembly,installation & commisioning of 33/11 KV gang operated isolating Nos. 1651.25
switch including installation and dismantling of fabricated steel required for
mounting of 33/11 KV Gang operated isolating switch for sectionalizing
33/11 KV lines with setting for accurate operation including fixing of allied
accesories complete in all respect with post insulator and jumpering on both
ends for connection with the system,.
[15]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
1 2 3 4
6.37 Dismantling of existing 6.35/0.24 KV transformer and structure from 3 m Nos. 1390.52
height structure and installation, testing as per Nigam’s norms &
commissioning of 6.35/0.24 KV transformer on existing support and raising
height of structure from 3 m to 5 m from ground along with earth
connections from existing earthing, including welding of transformer with
base channels and by welding of Nuts and Bolts. (clamps of suitable size
and earth strip if required will be supplied by Nigam.)/existing S.F.U shall
also be lifted at proper place if possible otherwise same shall be deposited
in AEN store along with other removed material.
6.38(a) Tag Welding of single-phase transformer at different three places in Nos. 38.23
Nigam’s stores one (at welded strips already provided) +2(with
additional patties of size 55X30X5 mm)
(e) Tag Welding of Nuts and Bolts(with sealing bolts) at different 5 to 6 places Nos. 49.66
at welded strips already provided on M&P boxes fitted on 11/0.4 KV 3
phase 16/10KVA three phase transformers as per latest drawing and
design of Nigam in the stores for which adequate space and electricity will
be provided by Nigam and handling of tranformer will be done by Nigam.
(f) Welding of door(s) (continuous welding of patties and tag welding of Nuts & Nos. 181.40
Bolts with sealing bolt ) of M&P box fitted on 11/0.4 KV, 3 phase 25/40/63
KVA transformer at 5 to 6 places with two nos. patties at Sub-Division Store
(one made of flat size 75x30x5 mm or 75x40x5 mm and other patti made of
flat size 55x30x5 mm or 55x40x5 mm is to bewelded on side of the box and
other patti of size 55x30x5 mm or 55x40x5 mm is to be welded on door of
the box to form locking arrangment through Nuts & Bolts (size 1/2"x1 1/2")
as per latest drawinf and design of nigam Patties and Nuts & Bolts will be
provided by Nigam
(g) Continuous welding of three sidessliding front cover of meter chamber (size Nos. 64.40
400x2+390=1190 MM) of M&P Box for 10/16/25/40 KVA for three phase
transformers including tag welding of 12 nos. nut & bolts used in TN-2217
and onwards.
6.39 Replacement of defevtive items in LT Pillar Boxes (Only Labour Vharges):-
1 2 3 4
6.40 Erection of 11 KV RMU complete with accessories on existing foundation Nos. 4142.54
including use of special tools & conducting all pre-commissioning test
before energization, connecting the cable ect. Complete in all respect with
erection & groutinh of structure (excluding civil works for which payment
shall be made extra as per clause No 2.6 of CLRC). The relays will be
tested by Discom.
6.41 Erection of 2 Plole & 4 Pole DT Structure of 11 KV RMU complete in all
respect (excluding civil works for which payment shall be made extra as per
clause No. 2.6 of CLRC).
(a) 2 Pole Structure (Approx 548 Kg) Nos. 996.65
(b) 4 Pole Structure (Approx 691 Kg) Nos. 1256.03
NOTE:-
1 Dismentling charges for all the items will be 60% of item rates of erection charges.However
charges for transportation of the material from works site to the sub-division store shall be
paid as item rate of chapter III(Transportation of material).The payment will be after issuance
of certificate by the AEn.concerned that all the dismentled material has been safelyreceived
in the sub-divisional store.
2 The Quality of the material supplied by the contractor be got checked and approved by the
Circle S.E.
3 The nuts & bolts provided / Supplied by the contractor will be confirm to relevant ISS.
4 In case of pole upper end of the G.I wire provided for earthing shall be bolted with crossarm
5 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable
[16]
CHAPTER-7
STRINGING OF CONDUCTOR/ EARTH WIRE
[17]
Chapter DESCRIPTION OF WORK UNIT Rate
Code /Unit
No
1 2 3 4
7.4 Drawing & stringing of G.I. 4 wire over the guarding bracket for guarding of road
crossing /P&T crossing /Railway track crossing (for one span only)with cross G.I.wire
laces at an interval of two meter each or required as per location using EYE bolt, nuts
and bolts with washers etc.including binding .The EYE bolts and other nuts and bolts
will be provided by thecontractor for which payment will be made as per prevailing
Discom store issue rates.
a 1cX25 + 25 Sq mm Km 2107.91
b 3cx16+25 Sq mm Km 3161.87
c 3cx25 + 25 Sq mm Km 3688.85
d 3cx50 + 35 Sq mm Km 4637.41
7.7 Fixing of suspension clamps suitable for ABC cable set 52.62
7.8 Fixing of dead end clamps suitable for ABC cable set 52.62
7.9 Fixing of LT connectors type "A" suitable for ABC cable with cover.(including set 26.39
termination of service lines)
7.10 Fixing of LT connectors type "B" suitable for ABC cable(including cable termination) set 26.39
NOTE:-
1 Dismantling charges for all the items will be 50% of item rates of erection charges.However charges for
transportation of the material from works site to the sub-division store shall be paid as item rate of
chapter-III(Transportation of material ).The payment will be made after issuance of certificate by the
AEn. concerned that all the dismentled material has been safely received in the sub-divisional store.
2 The quality of material supplied by the contractor be got checked and approoved by the Circle S.E.
3 The nuts and bolts provided / supplied by the contractor will be confirmed to relevant ISS.
4 The nuts and bolts will be provided / supplied by the contractor for which payment will be made as per
prevailing Discom store issue rates.
5 The Rates are inclusive of all applicable Taxes/duty except service tax which will be paid extra by
Nigam if applicable.
Chapter DESCRIPTION OF WORK UNIT Rate
Code /Unit
No
1 2 3 4
AEN-TW XEN(TW-II) Sr. A.O.(TW) SE(TW)
[18]
CHAPTER-8
EARTHING OF LINE AND SUB-STATIONS
1 2 3 4
8.1 Earthing of line for all type of supports as per REC construction Nos 341.79
standards using Stay wire/GI wire with one pcs.of M.S.rod20mm dia
each 3 meter long and driving into earth by mechanical means as per
approved design.Drawing &specification.All material except MS rod,MS
flat & stay wirewill be supplied by the contractor.If material is supplied
by the contractor ,the payment will be made as per prevailing
Discomstore issue rates.(In case of PCC poles earthing must be
connected with earthwire already available on PCC pole at bottom)
8.2 Earthing of 11/0.4 KV distribution transformer /sub-station with 3 pieces Per Trans. 229.02
of M.S.Rod 20mm dia each 3 meter long and driving them into earth by
mechanical means at a distance as per approved design & drawing &
specification.The work includes flattening of top ends of M.S.rod drilling
a hole of 9/16" dia.at flattened top and tightening of M.S.flat 50x6mm
(having 3 hole 2ends and 1mm middle) with nuts and bolts with
M.S.rods top end hole.The flat will also be welded with M.S.rod.The
end will be connected to equipments as under in sequence.
8.3 Mesh earthing for 33/11 kv sub-station as per approved map &design
usingMS flat 50X6mm/MS road 20mm dia includinglaying of flat/rod at
the depth of 0.65 Mtrs.,welding & jointing at joints , structures &
equipments etc.asunder:
8.3.1 Excavation of trench of 0.65Mtrs.depth and 0.5Mtr.width
(a) Normal soil Cum 123.57
(b) Hard Soil Cum 155.65
(c) Ordinary rock ( where blasting is not required.) Cum 304.95
(d) Hard rock ( where blasting is required.) Cum 904.31
8.3.2 Laying of MS flat /MS rod in 0.65Mtr.deep excavated trench and Mtr. 26.23
welding of MS flat/rod continuosly with 100 mm overlaping for straight
joint including coating of MS flat joints with molten bitumen and
covering joint with bitumen impregnated tape to protect from rust.
8.3.3 Shaping of MS flat for connecting the equipments with earthmesh .The Mtr. 39.50
work includes the welding of MS flat with equipments/structure and
also with earth mesh.The work also includes coating of MS flat joint
with molten bitumen and covering jointwith bitumen impregnated tape
to protect from rust.
[19]
1 2 3 4
8.3.5 Filling of trench with available excavated muck in layers of 20cm R.Mtr. 5.23
(Max.)consolidating each deposited layer by ramming & watering with
lead up to 50 Mtr, and lift up to 1.5 Mtr.
8.3.6 Painting of exposed portion of MS flat/rod with two coats of red-oxide Mtr. 7.27
primer and two coats of green enamel paint.including material.
8.4 Earthing on 6.35/.24 KV S/S made with 4 nos. MS Rod 20 mm Per.Trans. 249.74
dia,electrodes (black) of 3 Mtr. Length to be driven in earth by
mechanical means and jointing through transformers body, 11 KV
neutral ,LT neutral & LA with MS flat 40x5 mm ( black 32 mtr.) .The MS
Flat will be welded at the top of the electrode.
8.5 Earthing of new 33/11 KV S/S with bentonite compound (including Per earthing 5767.53
material ) involving following activities.
8.5.1 Digging of 10.5 ft. deep pit of 4 ' dia ( approx 132 cu.ft)
8.5.2 Supply of 2" G.I pipe with cap(including fabrication of 30 holes in the
periphery of pipe)
8.5.3 Making chamber for water pouring including cast iron manhole cover
Note:-
1 The quality of material supplied by the contractor be got checked and approved by the
Circle S.E.
2 The nuts and bolts provided / supplied by the contractor will be confirmed to relevant ISS.
3 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable
[20]
CHAPTER-9
METER AND SERVICE LINES
1 2 3 4
9.1 Fixing of single phase meter box at the premises of existing/new consumer
with 4 Nos Anchor fastners of rust proof size M-6x50 mm on the wall as per
the position of the holes already provided on the meter box. The meter box
must be housed perfectly vertical/plumb line,anchor fasteners are to be
supplied/provided by the contractor (including self carriage from S/D store
to consumer's site)
[21]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
9.5 Fixing of single phase energy meter in meter box by providing machine
screws making holes on backelite sheet as per requirement & also making
connections at meter terminals and MCB using Thimbles(by crimping)
including providing M-seal compound inside meter box. The bakelite sheet
must be fixed properly with Screws to restrict the movements vertically or
horizontally. The meter is also required to be checked for proper functioning
after making connections of service lines with distribution mains by licenced
contractor only. The screws will be provided by contractor. Payment for lugs
will be made extra @ Rs.1.00 per wire for single phase connection if not
available with JVVNL& provided by contractor.(including safe carraige)
[22]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
9.8 Laying of 1100 volt heavy duty armoured XLPE cable of aluminum coudctor
of following size conforming to IS: 7098 (Pt-I) (latest amended) overhead
service line from pole to meter terminals for release of new LT
connections/replacement of damaged/obsolete service line (except
agriculture one). The cable must be fixed on wall with clamps /hooks
properly at a interval of one meter.
9.12 Supply & fixing of cable tray made of slotted anble painted by synthetic
enamel paint (traditional pink colour) with minimum 2nos. Anchor fastners
per meter length of rust proof size M-6x65mm on the wall as per rounte of
the cables / service line to laid surface mounted on the wall. The cable tray
must be installed perfectly in horizontal line, ancher fastners are to be
provided/ supply by the contractor( including self carriage from S/dn. store
to site)
NOTE:-
1 The quality of material supplied by the contractor be got checked and approved by
the Circle S.E.
2 The nuts and bolts provided / supplied by the contractor will be confirmed to relevant
ISS.
3 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable
1 2 3 4
[23]
CHAPTER-10
ERECTION OF 33KV SUB-STATIONS & BUS BAR
1 2 3 4
10.1 Erection of steel supports in the excavated pit in alignment after
checking then same with plumb line as per approved design and
drawing of 33/11KV Sub- station.The support should be grouted
and muffed in cement concrete ratio 1:3:6 as per chapter -5 code
No.5.7.The remaining portion of the pit will be back filled with
soil.The charges for grouting & muffing will be paid by extra as per
chapter code no 5.7 The nuts & bolts will be supplied by the
contractor for which payment will be made as per prevailing Store
issue rates.
The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
3
paid extra by Nigam if applicable.
11.2 Installation of control panel including checking of wiring and conducting all pre-
commissioning tests before energization, satisfactory operation of all equipment
existing thereof. ( The relay will be tested by Discom ).
11.4 Erection & commissioning of battery set and battery charger including all
required connection/wiring from battery set to battery charger and A.C.mains
complete in all respect.
[25]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
11.5 Laying, testing termination of control cable 1100 volts PVC insulated including
supply and installation of ferrules to designate various cores of control cables
by terminal Nos. of identification including utilization of cable gland. The control
cable should be clearly arranged in trenches avoiding crossings including
clamping of control cable at regular interval and providing identify tags.
(A) The top cover of junction box should have slope of 10 mm so that water is not
collected on top of the box.
(B) 18 Nos. terminal blocks of 30 Amp. Bolted type with end plate and screws fixed
on 36 cm mounting channel for terminal block with bolts & nuts of 25x9
Sq.mm.on side support inside junction box. The terminal blocks should be
detachable type, which can be removed or added individually and suitable for
4/6 Sq.mm.coppers lugs. The terminal blocks should be preferably of
GEC/Alsthom/ Essun/Malamin PVC or equivalent make.
(C) The supports of junction box made of M.S.Angle size 45x45x5mm with cleat
having 1.2 meter length of each support should be grouted in cement concrete
ratio 1:3:6.
11.7 Laying, connecting, testing and commissioning of 1100 Volt PVC cable at 33/11
KV Sub-Station including connections of leads cutting stripping of cable
insulation providing compression type terminals fixing of cable glands crimping
of lugs clamping of cable cores etc. complete in all respect as per requirement
of Engineer Incharge. PVC cable size.
[26]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
11.8 Supply,transportation and laying of sand layer of 75 mm below the power cable
and 75 mm above the same alongwith using 200x100x75 mm size Class-II
bricks in channel shape comprising of following sizes as under the back filling in
the layer of compacted 100 mm thick earth,. Cable will be laid as per the
methods of IS:1255 and details in 11.13
11.8.1 For Single Power Cable, the trench width will be 350 mm using 20 Nos of bricks Mtr. 83.08
of above specification.
11.8.2 For Double Power cable, the trench width will be 470 mm using 35 Nos of Mtr. 139.35
bricks of above specification.
11.8.3 For Triple Power Cable, the trench width will be 590 mm using 50 Nos of bricks Mtr. 195.33
of above specification.
11.9 Laying energisation & commissioning of underground cable for working voltage
of 11 KV/33 KV Aluminium conductor ,Power cable XLPE/PILCA armoured in
RCC class NP-2 Non-pressure pipes of sizes mentioned against each refilling
of earth in the remaining excavated area making necessary connection
including testing etc. as required (It includes providing, laying & jointing RCC
class NP-2 Non-pressure pipes conforming to IS:458 of approved make with
collars, jointed with CM 1:20 depth of cable shall be 1.2 meter. (Cable shall be
provided by the Nigam).
(A) 33 KV Cable
11.10.1 3x185 sq. mm in pipe of dia 300 mm Mtr. 549.89
11.10.2 3x300 sq. mm in pipe of dia 300 mm Mtr. 549.89
(B) 11 KV Cable
11.10.3 3x150 sq. mm in pipe of dia 250 mm Mtr. 412.34
11.10.4 3x185 sq. mm in pipe of dia 250 mm Mtr. 412.34
11.10.5 3x240 sq. mm in pipe of dia 300 mm Mtr. 549.89
11.10.6 3x300 sq. mm in pipe of dia 300 mm Mtr. 549.89
11.10.7 3x400 sq. mm in pipe of dia 300 mm Mtr. 549.89
11.11 Providing and fixing of G.I. Pipe B-Class (IS:1239 marks) at the starting and
finishing point of 33 & 11 KV under ground cables and to lay & clamp vertically
with the existing support including labour charges.
11.11.1 Providing and fixing of G.I. Pipe of 125 mm diameter. B-Class (IS:1239 mark),at Mtr. 1402.26
the starting and finishing point of 11 KV under ground cables and to lay &
clamp vertically with the existing support including labour charges.
11.11.2 Providing and fixing of G.I. Pipe of 150 mm diameter. B-Class (IS:1239 mark),at Mtr. 1590.07
the starting and finishing point of 33 KV under ground cables and to lay &
clamp vertically with the existing support including labour charges.
[27]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
11.12 Installation of metering points on 11 KV Out going feeder at 33/11 KV S/S. Nos 20162.64
(d) Meter:
Meters should be fixed firmly inside the tamper proof box, as per drawing. All
the meter fixture will be provided by contractor including all consumables.
(f) Painting:
All surfaces interior and exterior of lattice structure shall be white aluminum
painted.
(g) Commissioning of Metering Equipments:
Installed meters inside the box and metering equipments duly mounted on the
mounting structure will be powered up by connecting load in the presence of
the concerned Assistant Engineer who will arrange the necessary shut down.
The completion certificate shall be furnised by contractor.be filled accordingly.
Since the work involves higher A.C. voltage level, the contractor shall take full
care regarding safety norms, so as to avoid any accidental hazards.
NOTE: The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
1 2 3 4
12.1 Painting with priming coats or ready mixed red-oxide paint 2 coats of
approved make on steel works after cleaning with wire brush / sand
paper.(including cost of red oxide)
12.1.1 On new surface sq.mtr. 33.11
12.1.2 On old surface sq.mtr. 24.83
12.2 Painting with aluminium paint of approved brand and manufacturer to
give an even surface.(including cost aluminium paint)
NOTE:-
1 Rates are inclusive of paints brush ,sand paper spray gun and any
scaffolding material,if required.
2 Rates are inclusive of cleaning ,stains ,smear splashing and dropping
of every kind from such places and things/equipments.
NOTE: The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
[29]
CHAPTER-13
LIGHTING FIXTURES
1 2 3 4
13.1 Instalation and commisioning of the following type of new fixtures
including wiring and required connections to connect all allied
accessories fixtures as required but without material.
13.2.4 G.I.pipe bracket 16mm dia of required size and shape including Mtrs. 184.81
clamp of MS flat 40x4sq.mm with MS nuts &bolts and washers for
HPMV / HPSV lighting fixtures.
NOTE:
1 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
[30]
CHAPTER-14
FABRICATION
1 2 3 4
14.1 Fabrication of steel structures of M.S angle ,M.S.channel &
M.S.Flat including cutting ,drilling as per design and drawing.
14.2.1 33 KV Cross Arm (Angle ) with clamp and Top Hamper with MT 4514.70
clamp (22.849 Kg)
14.2.2 33 KV Cross Arm (channel) with clamp and Top Hamper (26.831 MT 4514.70
Kg)
14.2.3 11 KV Cross Arm angle with clamp and Top Hamper (13.797 Kg) MT 4514.70
[31]
CHAPTER-15
MAINTENANCE OF LINES
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
Note: Incharge Assistant/Junior Engineer after necessary inspection
testing & checking will identify the maintenance works which will be
categorised as below.
15.1 Joint inspection & patrolling of lines,feeder wise for identification of Km. 77.34
maintenance work to be carried out.
15.2 Removal of Bird's nest & foreign material from line.
(a) For Jaipur city circle Km. 618.20
(b) For other District Headquarter Km. 397.44
(c) For others Km. 176.68
15.3 (A)-Providing of numbering on single pole or double pole structure, Nos. 15.50
feeder wise with good quality enamel paint as per requirement.
1 2 3 4
[32]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
15.9 Replacement of defective/damaged 11 KV Disc Insulators including
removing/providing jumpers with line conductor.
1 2 3 4
[33]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
15.15 Replacement of broken/damaged poles in between the line with
excavation of pit in alignment after checking the same with plumb
line, re-fixing of cross arm bracket, top hampers, clamps insulators &
binding/jumpering etc. and removal of broken pole.
[34]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
15.17 Replacement/ Fixing of stay wire including guy insulator & stay
clamp.
15.17.1 G.I. Stay wire 7/8 SWG Nos. 342.37
15.17.2 G.I. Stay wire 7/10 SWG Nos. 245.15
15.18 Replacement/ providing of stay set including excavation of pit &
back filling with soil & proper ramming fastening clamping of stay
wire with stay insulators.
[35]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
15.24 Sectionalising of existing line including replacement of
bracket,insulators with pin/hardware's providing of stay sets with
stay wire and stay insulators, jumpering & binding etc.
15.24.1 33 KV line S/C with ACSR 'Dog'/ 'Racoon'. Nos. 2759.83
15.24.2 11 KV line S/C with ACSR 'Dog'/ 'Racoon'. Nos. 2671.50
15.24.3 11 KV S/C line with ACSR 'Weasel'. Nos. 1545.54
15.24.4 LT line three phase Nos. 684.42
15.24.5 Lt line single phase Nos. 635.82
15.25 Replacement of defective/ danaged overhead ABC conductor (Areal
bunched cable) on existing erected pole/ support using Suspension
& Dead End Clamps icludinglaying, Jointing, stringing complete in
all respect & dismentalling of old ABC Conductor (Aerial Bunched
Cable)and depositing it to concern ACOS. If in any case new
Suspension? Dead End Clamps/ connectors are requiredthen same
may be dealt with item No. 7.7, 7.8, 7.9 & 7.10 (The payment shall
be made in accordance with the quantity mentioned in the MCN.
Since the qty in the MCN is by weight, as such for converting into
KM refer Measured Weight of Meterial of CLRC). Reats are
Inclusive of dismentalling charges.
1 2 3 4
B Condition of Stay Sets e.i Loose/ Broken/ Without Guy Insulator/
Proper Clamping with Pole or any additional requirement of Stay
Sets (if required).
C Position of Fixtures i.e Crodd Arm/ Top Hamper/ Channal Bracket/
Angle Bracket ect. Whether Tilled or Properly Mounted.
1 2 3 4
15.29 Identifiying the unused material erected/ tying in the field,
dismentallingfrom site, their safe carriage including loading & un-
loading and deposition of samein concerded ACOS of S/ Dn (PCC
poles shall beposited with concerned Sub-Division or Receipt of
concerned AEN for PCC poles.
(a) PCC Poles (All Sizes)
(i) Within 10 Kms. Per pole 404.68
(ii) Above 10 Kms. & upto 30 Kms. Add for each Km. or part thereof. Per pole 5.03
(iii) Above 30 Kms. Add for each Kms. of part thereof. Per pole 2.59
(b) Steel (Fabricated and unfabricated) i.e MS Rails, RS Joists, MS
Channels, MS Angles, MS Flat and GI Stay sets, Gi Stay Wire, Gi
Wire Nut & Bolts, ACSR Conductor, Insulators (usaable),
Hardwares, cables etc.
(i) Within 10 Kms. MT 1436.87
(ii) Above 10 Kms. & upto 30 Kms. Add for each Km. or part thereof. MT 4.89
(iii) Above 30 Kms. Add for each Kms. of part thereof. MT 3.03
( c) Fabricated lattice towers Structures and sub-station structures type
AB, AB beams, isolators, Line Structure ect.
(i) Within 10 Kms. MT 3494.39
(ii) Above 10 Kms. & upto 30 Kms. Add for each Km. or part thereof. MT 4.89
(iii) Above 30 Kms. Add for each Kms. of part thereof. MT 3.74
Note:-
1 The quality of material supplied by the contractor shall be got checked & approved by the
circle SE.
2 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
Note:- Since only the Nigam empolyee is empower to work on live line? Equpment thus the
Executive Engineer shall ensure the following from the contractor whileengaging Pvt.
Person (ITI Holder) for working on Live Line/ Equipments:-
1 At the Joining the contractor should submit Accidental Insurance Cover in advancefor One
Year for the engaged person.
2 The Contractor Should submit age proof, copy of ITI Certificate for the engaged person.
3 The Contractor should submit proof of deduction of PF (if Applicable) and deposition of
samewith PF department along with bill otherwise submitecemption certificate for the
engaged person.
4 The person should submit work experience for live line workor should submit a certificate
to be issued from Electrical Inspector for working on Live Line.
5 Identity Card with Photo for the deployed person should issued by Circle SE and proper
record of it should be maintain at circle level.
6 Monthly/ Routine verification of the deployed person should be done by circle office.
1 2 3 4
16.1 General maintenance of distribution transformer as under:- C
1 Cleaning of dust and oil scale deposits outside the body of transformer with
detergent and water.
2 Tightening all nut and bolts.
1 2 3 4
[37]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
16.8 Providing and replacement of damaged top cover tank rubberized cork
gasket on the various size of distribution transformer as under:
16.11 Providing and filling of transformer oil top up in the transformer where the oil Per Litre 58.38
value are within permissible limits(Oil level should not be below the core of
the transformer.
16.12 Providing and replacement of transformer oil in those transformer where the
oil value are not within permissible limits.
(a) Fresh oil as per IS:335 Per Litre 58.38
(b) Buy back price of the oil taken out from the such transformer. Per Litre 22.42
16.13 Rapairs and maintenance of 11 KV isolators including replacement of Set 307.76
damaged post insulator G.O.jaws/blades, clamps and checking of operating
mechanism with oiling /greasing for smooth operation.
16.14 Maintenace of 11 KV Horn gap fuse set including replacement of parts post Set 128.06
insulator etc.
16.15 Replacement / fixing of complete 11 KV isolator /G.O.switch with all Set 921.14
accessories including jumpers.
16.16 Replacement /fixing of 11 KV horn gap fuse set(3limbs) in place of damaged Set 512.27
H.G.fuse set /D.O.fuse set including modification of the structure etc..
16.17 Replacement / fixing of 11 KV lightening arrestors including jumpers and Nos. 56.13
earth connections.
1 2 3 4
[38]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
16.18 Replacement of damaged distribution transformer by new / repaired
transformer including making connections on HV and LV side body and
neutral earthing & testing & commissionig of the transformer.The above
work includes lifting of transformer from sub-divisional store and
transportation upto site and also depositing damaged / removed transformer
in sub-divisional store.
16.20 Replacement of L.T.fuse board / I.C.T.P/MCB.switch with clamp including Nos 31.45
Clamping & making cable connections complete in all respect.
16.21 Measurement of load during peak hours on each phase on L.V side of Nos 76.45
distribution transformer on outgoing feeders. by clip on Ammeter/Tong tester.
16.22 To supply & replace burnt/ damaged flexible PVC Wire, Lugs and Bakelite
Sheet in M&P Box of different ratings to Three Phase & Single Phase
transformer in Nirgam Store:- Note:- (Our going cables is also to be
connected on the output terminals duty tigtened & crimped properly for out
goingconnections for which required cable shall be provided by Nigam
MCCB shall be provided by Nigam.
A Three Phase Transformer:-
i 25/ 40 KVA (PVC Wire: 25 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 1444.40
Backalite Sheet) Transformer
ii 10/ 16 KVA (PVC Wire: 16 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 995.44
Backalite Sheet) Transformer
B Single Phase Transformer:-
i 25 KVA (PVC Wire: 70 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 603.52
Backalite Sheet) Transformer
ii 16 KVA (PVC Wire: 35 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 410.32
Backalite Sheet) Transformer
iii 10 KVA (PVC Wire: 25 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 340.40
Backalite Sheet) Transformer
iv 5 KVA (PVC Wire: 25 Sq mm Lugs: As per Drawing (Annecsure- I) & Per 195.96
Backalite Sheet) Transformer
16.23 Spary painting on the surface with synthetic enamel paint (ICI Asian, Burger
or equivalent make) to give an even shade (minimum two coats)with
oerparation of surface by rubbing applying primercoats of red oxide
(minimum by coats) and putty etc. complete in all respect on M&P Boxes of
Transformers (including cost of paint & reg oxide)
(i) Three Phase Transformer:-
(a) 10 KVA & 16 KVA
On new surface Per Box 175.52
On old surface Per Box 165.62
(b) 25 KVA & 40 KVA
On new surface Per Box 239.71
On old surface Per Box 226.19
(ii) Single Phase Transformer:-
(a) 5/10/16/25 KVA
On new surface Per Box 67.56
On old surface Per Box 63.76
NOTE:-
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
Rates are inclusive of paints brush sand paper spray gun and any scaffolding
material, if required and also inclusive of cleaning stains smear splashingand
dropping of every kind from such places and things/ equipments. The quality
of material supplied by the contractor be got checked and apptoved by the
Circle SE.
16.24 (A) To supply iron Cilts made of Flat size 90 mm x 90 mm x 3 mm thik & weld it Per 430.10
continiously, 3 Nos on each side (Total Six Nos) in case of Three Phase Transformer
Transformer except bottom side of M&P Box in Nigam Store.
16.24 (B) Per 215.07
To supply iron Cilts made of Flat size 90 mm x 90 mm x 3 mm thik & weld it Transformer
continiously, 1 Nos on each side (Total Three Nos) in case of Three Phase
Transformer except bottom side of M&P Box in Nigam Store.
16.25 To Supply and install/ Weld the Meter cover on Three Phase Transformer in
Nigam Store.
A Rating: 10 KVA & 16 KVA
The cover shall be supplied with assessories (Cover Size 650x550, Glass, Per 854.09
Kabja, LED, Fabrication Charges, Paints, Shocker, Lock) along with iron clits Transformer
made of Flat size 90 mm x 90 mm x 3 mm thick (clits should be welded
continiously) 2 Nos on each side (Total Six Nos) except bottom side of M&P
Box of Three Phase Transformer.
B Rating: 25 KVA & 40 KVA
The cover shall be supplied with assessories (Cover Size 810x685, Glass, Per 1014.27
Kabja, LED, Fabrication Charges, Paints, Shocker, Lock) along with iron clits Transformer
made of Flat size 90 mm x 90 mm x 3 mm thick (clits should be welded
continiously) 2 Nos on each side (Total Three Nos) except bottom side of
M&P Box of Single Phase Transformer.
16.26 To Supply and install/ Weld the Meter cover on Single Phase Transformer in
Nigam Store.
A Rating: 5 KVA/ 10 KVA/ 16 KVA/ 25 KVA
The cover shall be supplied with assessories (Cover Size 220x370, Glass, Per 382.36
Kabja, LED, Fabrication Charges, Paints) along with iron clits made of Flat Transformer
size 90 mm x 90 mm x 3 mm thick (clits should be welded continiously) 1
Nos on each side (Total Three Nos) except bottom side of M&P Box of
Single Phase Transformer.
16.27
Note:
1 The quality of material supplied by the contractor shall be got checked & approved by the circle
SE.
2 The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra by
Nigam if applicable.
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
1 2 3 4
Note: Incharge Assistant/Junior Engineer after necessary inspection
testing& checking will identify the maintenance work which will be
categorised as below:
17.1.1 Labour charges for over all inspection of sub-station with two per trans. 903.55
transformer for job requiring works analysis and testing of dielectric
strength of oil, insulation resistance value and earth resistivity etc.
HV Side
17.6.1 Upto 1.6 MVA transformer Nos. 1357.56
17.6.2 Above 1.6 MVA & upto 3.15 MVA transformer. Nos. 2591.58
17.6.3 Above 3.15 MVA & upto 5 MVA transformer. Nos. 2591.58
LV Side
17.6.4 Upto 1.6 MVA transformer Nos. 531.09
17.6.5 Above 1.6 MVA & upto 3.15 MVA transformer. Nos. 1820.32
17.6.6 Above 3.15 MVA & upto 5 MVA transformer. Nos. 1820.32
17.7 Dehydration/Filteration and reconditioning of transformer oil Ltr. 4.37
(electricity shall be supplied by deptt.) as per norms and testing
thereof in presence of sub-station Incharge.
17.8 Cleaning of oil scale deposits over the body and radiators of power
transformer with thinner/detergent and de-rusting in perfect manner.
1 2 3 4
[40]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
17.9 Replacement of oil temperature indicator, Winding temperature
indicator,silica gel container ,Presser relief device ,Magnetic oil level
gauge,.Gas operated Buchhloz relay (including all required
accessories.)
17.10 Spray Painting of the power transformer from out side with two
coats of synthetic enamel paint of required shade after cleaning the
body and radiators with preparation of surface by rubbing &
applying primer coats and putty etc. and making smooth surface
with the fine emary cloth including required material and tools.
[41]
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
17.16 Replacement of 33 KV/11 KV lightening arrestors including
jumpering and earth connections etc. in all respect.
17.16.1 33 KV L.A. Nos. 167.49
17.16.2 11 KV L.A. Nos. 55.08
17.17 Repair & maintenance of 33 KV/11 KV Isolator/ G.O. Switch for
smooth operation including replacement of G.O. clamps, jaws,
blades & post insulators etc. and checking of operating mechanism,
oiling/greasing complete in all respect.
17.17.1 33 KV Isolator/ G.O. Switch Nos. 451.78
17.17.2 11 KV Isolator/ G.O. Switch Nos. 302.04
17.18 Welding of fabricated MS Sheet box of 2 mm thickness for locking
arrangement of power transformer valves to curb transformer oil
having dimensions
17.18.1 200x160x180 mm for filter valve of Power Transformer per valve 451.47
17.18.2 160x100x120 mm for conservator drain valve per valve 305.49
17.18.3 40x 50x40 mm for radiator air release cap per valve 99.32
17.18.4 60x 50x60 mm for conservator cap per valve 103.83
Removing of unwanted grass/ small plants from the 33/ 11 KV sub-
17.19 Station.
(a) From gravelled land/ area. Per 100 Sq Mtr 201.66
(b) From un-gravelled land/ area. Per 100 Sq Mtr 131.01
17.20 Mesurment of earth resistance:-
(a) By providing earth resistance tester by contractor. Per Location 23.00
(b) By providing earth resistance tester by Nigam. Per Location 18.40
Carrying our following activities at 33/ 11 KV S/s The necessary
material. T&P & safety devicesreruired fro maintenance shall be
provided by Nigam. Applicable statuary deductions shall be made
17.21 as per rules.
Providing one skilled person (ITI holder) for shift duty (per shift of 8 Per Shift 233.00
Hrs.) Note:- Engagement of Skilled person is subject to fulfilment of
i note conditions 1 to 4 given below the chapter.
Providing 1 semi-skilled labour for shift duty (Per shift of 8 Hrs.) for Per Shift 223.00
assisting in performing the activities as below. Note:-
Engagement of Semi-skilled person is subject to fulfilment of note
ii conditions 1&3 given below the chapter.
To ensure un interrupted power supply during Block hours on the
feeders eminating from GSS as directed by AEN/ JEN and to
A maintain porper Log Sheet.
To register ON/ OFF timmings of 33 KV feeder in the Log Sheet.
B
To ensure the Breaker OFF position, Isolation of 11 KV GO, Switch
& Proper earthing by earthing chain before permitting the Shut
C Down of 33 KV/ 11 KV feeders.
Maintain the 33/ 11 KV S/S like repairing the jumpers, change of
faulty Disc/ Pin Insulator cleaning of Switch Yard, watering the
D earthing pits cleaning & caring the equipments.
Replacing the burnt Fuse during Single Phase & Three Phase
E supply.
To record the tripping for the & type of fault occurred in any 33 KV/
11 KV feeder and give a try for restoring the supply, if the breaker
does not hold i.e feeder remain faulty then message should nbe
immediately conveyed to the Line Man of respective feeder and also
F to concerned officer.
If any defect has been observed in the installed equipments at the
S/S, then message should be immdiatelyconveyed to the concerned
G JEN/ AEN.
Keeping watch & ward of Nigam material lying at the Permisis of
H S/S.
Chapter DESCRIPTION OF WORK UNIT Rate/Unit
Code No
1 2 3 4
Properly hand over the shift to next shift duty staff indicating the
I position of all equipment/ feeders.
To Supply & Replace the damaged/ defective parts of 33 KV GO
switch (Proper shut down will be provided by Nigam). Rates are
17.22 inclusive of material.
A 33 KV GO (800 Amps)
i Contacts/ Jaws with Terminal Plate Nos. 1391.96
ii Center Blade/ Pipe Nos. 2640.40
iii Post Insulator (24 KV) Nos. 354.20
iv PG Clamp Nos. 256.68
To Supply & Replace the damaged/ defective parts of 11 KV
Roaster Switch (Proper shut down will be provided by Nigam).
17.23 Rates are inclusive of material.
a Contacts/ Jaws with Terminal Plate Nos. 488.52
b Center Blade/ Pipe Nos. 672.52
c Post Insulator (12 KV) Nos. 219.88
d PG Clamp Nos. 92.92
NOTE:The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra
by Nigam if applicable.
Note:- Since only the Nigam empolyee is empower to work on live line? Equpment thus the
Executive Engineer shall ensure the following from the contractor whileengaging Pvt.
Person (ITI Holder) for working on Live Line/ Equipments:-
1 At the Joining the contractor should submit Accidental Insurance Cover in advancefor One
Year for the engaged person.
2 The Contractor Should submit age proof, copy of ITI Certificate for the engaged person.
3 The Contractor should submit proof of deduction of PF (if Applicable) and deposition of
samewith PF department along with bill otherwise submitecemption certificate for the
engaged person.
4 The person should submit work experience for live line workor should submit a certificate
to be issued from Electrical Inspector for working on Live Line.
5 Identity Card with Photo for the deployed person should issued by Circle SE and proper
record of it should be maintain at circle level.
6 Monthly/ Routine verification of the deployed person should be done by circle office.
FENCING WORKS
1 2 3 4
18.1 Providing and fixing 180 cm high fencing with angle iron post size Running 720.85
50x50x6mm placed at every 3 meters apart and 45cm in ground meter
embedded in cement concrete 1:3:6 (30x30x60cm) corner and every
10th.post to the strutted with 50x50x6 mm angle iron provided with 6
horizontal lines and 2diagonals of G.I. barbed wire between two post
fitted and fixed with G.I. Staples including each works in excavation
etc. complete.
18.2 Providing and fixing 150 cm high fencing with angle iron post size Running 514.68
50x50x6mm placed at every 3 meters apart and 45cm in ground meter
embedded in cement concrete 1:3:6 (30x30x60cm) corner and every
10th post to the strutted with 50x50x6 mm angle iron provided with 6
horizontal lines and 2diagonals of G.I. barbed wire between two post
fitted and fixed with G.I. Staples including each works in excavation
etc. complete.
18.3 Providing and fixing 120 cm high fencing with angle iron post size Running 481.56
50x50x6mm placed at every 3 meters apart and 45cm in ground meter
embedded in cement concrete 1:3:6 (30x30x60cm) corner and every
10th.post to the strutted with 50x50x6 mm angle iron provided with 6
horizontal lines and 2diagonals of G.I. barbed wire between two post
fitted and fixed with G.I. Staples including each works in excavation etc.
complete.
18.4 Structural steel work riveted, bolted or welded in built up sections, per Kg 64.40
trusses and framed work, including cutting, hoisting (height upto 10 m),
fixing in position and applying a priming coat of approved steel primer
all complete:
18.5 Providing and fixing welded mesh/expanded metal mesh in frame work,
flat iron beading 20x3mm including top cross laps inside and out sides
elding, iron bolts, crews, clips etc. complete (excluding frame work) of
size.
18.5.1 Expended metal size 20-25 mm size 18SWG per Sq.M 651.36
18.5.2 Welded mesh 50 mm x 25 mm x 2.1 mm per Sq.M 603.52
18.5.3 Welded mesh 25 mm x 25 mm x 2.1 mm per Sq.M 627.44
18.5.4 Welded mesh 50 mm x 50 mm x 2.1 mm per Sq.M 579.60
NOTE:-The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
1 2 3 4
19.1 Supply of
19.1.1 Surface type teak wood Board with varnish and entire treatment
including fixing gutties etc.For installation of cut-outs holders and bulb
and on-off switch.
19.1.3 5 amp.porcelain base single pole tumber switch IS-3854 including Nos. 16.26
making connection etc.as required make:-
SK/555,RK/555,KINJAL,EMPERIOR.
19.1.4 Brass batten/Angle/pendent holder any ISI approved make including Nos. 34.76
making connections etc.as required.
19.1.5 Bulb 40/60 watt make PHILIPS/BAJAJ/GEC. Nos. 15.80
19.1.6 10 Amp. 240 Volts ISI mark MCB. Nos 102.64
19.1.7 CFL 14 W ISI mark Nos. 105.34
19.2 Supply with 4 Sq.mm. T/C XLPE armoured cable of aluminium meters 49.21
conductor confirming to IS (latest amendment) procured as per
specification of Nigam and approved vendor of Jaipur Discom.
19.2.1 Supply of 2.5 mm2 T/C XLPE armoured cable of aluminium conductor meters 36.87
confirming to ISS (latest amendment) procured as per specification of
Nigam and from the approved vendor of Jaipur Discom
19.3 Supply of PVC insulated solid aluminum conductor cable 1.5sq.mm. Meters 4.66
single core 1100V. Grade (IS.694) of standard quality and approved
Makes.
19.4 Supply of Angle 50x50x6 mm for supporting service line with nuts& Nos 142.21
bolts. (2' long)
19.5 Supply of 16 mm Dia MS Rod 2 Meter long along with GI. Wire 10SWG Nos 205.42
with nut& bolts.
NOTE:- The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
[44]
CHAPTER-19 (B)
TRANSPORTATION /ERECTION FOR KUTIR JYOTI / BPL CONNECTION IN RURAL AREA
19.2.1 Wiring service line from LT Pole to meter of the consumer with 2.5 meters 3.46
Sq.mm. T/C XLPE armoured cable of aluminium conductor confirming
to IS (latest amendment) procured as per specification of Nigam and
approved vendor of Jaipur Discom duly clipped/hocked and insulating
tape complete in all respect.
19.3 Drawing PVC insulated solid aluminum conductor cable 1.5sq.mm. Meters 1.52
single core 1100V. Grade (IS.694) of standard quality and approved
Makes duly clipped on wooden bottom.
19.4 Fixing of Angle 50x50x6 mm for supporting service line with nuts& Nos 18.92
bolts in cements Mortor. (2' long)
19.5 Fixing of single phase meter box at the premises of existing/new
consumer with 4 Nos Anchor fastners of rust proof size M-6x50 mm
on the wall as per the position of the holes already provided on the
meter box. The meter box must be housed perfectly vertical/plumb
line.
(a) Plastic Box Nos 61.77
(b) Metal Box Nos 78.89
19.6 Fixing of single phase energy meter in meter box by providing Nos 39.52
machine screws making holes on backelite sheet as per requirement
& also making connections at meter terminals and MCB using
Thimbles(by crimping) including providing M-seal compound inside
meter box. The bakelite sheet must be fixed properly with Screws to
restrict the movements vertically or horizontally. The meter is after
making connections of service lines with distribution mains by licenced
contractor only. The screws will be provided by contractor. Payment
for lugs will be made extra @ Rs.1.00 per wire for single phase
connection if not available with JVVNL & provided by contractor.
[45]
CHAPTER DESCRIPTION OF WORK Unit Rate/Unit
CODE NO.
19.7 Earthing with 16 mm Dia MS Rod 2 Meter long and driven them into Nos 47.54
earth by mechanical means.The work including flattening of top end
of MS rod drilling a hole at flattened end and tightening of earth
electrods I.e. G.I. Wire 10SWG with nut& bolts the other end will be
connected to the earth terminal provided at meter board.
19.8 Fixing of AC Static Energy meter 5-30 Amp. With LCD Display with Nos 94.93
moulded box (complete unit ) at the consumer's premises with 4 No.
Anchor Fasterners of rust proof size M-6X50 mm on the wall as per
the position of the holes provided on the meter box.The meter box
must be housed perfectly vertical/plumb line.
NOTE:- The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
[46]
CHAPTER - 20
ERECTION & COMMISSIONING OF CABLE
20.4 Laying of 33 KV XLPE Cable ( Aluminium Conductor ) underground as per relevant ISS /
JVVNL standard including excavation of 30 cm width x120 cm deep trench in Kaccha land
25 cm thick under layer of sand. 'A' class bricks or concrete block covering refilling soil in
the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable
and at every turn.
[47]
Chapter DESCRIPTION OF WORK UNIT Rate/
Code No Unit
20.5 Laying of two ( D/C) 33KV, XLPE (Aluminium conductor) undrground cables w/o
overlapping as per relevant IS/ JVVNL standard including excavation of 50 cm width x 120
cm deep trench in Kaccha land.25 cm thick under layer of sand. 'A' class bricks or
concrete block covering refilling soil in the remaining portion and providing/fixing cable
route indicators at every 30Mtr.of cable and at every turn.
A) 3x50 Sq mm to 3x185 Sq mm Mtr. 214.54
B) 3x 240 Sq mm to 3x400 Sq mm Mtr. 234.06
Note:- per meter shall be paid extra for excavation in Pakka Road. Mtr. 91.14
20.6 Installation of 33 KV Cable (XLPE) termination / straight through joints ( Heat shrinkable
type) as per manufacturer's kit guidance and direction including preparation of cable and
testing refilling etc as required.(Including crimping of lugs)
A) (I) Outdoor end terminal 3x50 Sq mm to 3x185 Sq mm Nos 1316.43
(ii) 3x240 Sq mm to 3x400 Sq mm Nos 1608.89
B) (I) Indoor end termination 3x50 Sq mm to 3x185 Sq mm Nos 1053.14
(ii) 3x240 Sq mm to 3x400 Sq mm Nos 1287.07
C) (i) Straight through joint 3x50 Sq mm to 3x185 Sq mm Nos 2964.35
(ii) 3x240 Sq mm to 3x400 Sq mm Nos 3432.32
Note:- Rate shall be reduced by 20% for "Push On" typekit
20.7 Laying of 33 KV & 11KV XLPE cable without Road cutting i.e. through burrowing machine
"VERMIER".(120 cm deep).Use of this technology must be restricted to the situation like:-
(i) When the passages available for laying the proposed cable is totally a metal or cement
concrete road.
(ii) When the road cutting is not permitted by the local administration.
A) 33 / 11 KV 3C x 300 Sq.mm cable Mtr. 308.20
B) 33 / 11 KV below 3C x 300 Sq.mm cable Mtr. 289.80
C) LT 3.5 Core 95 Sq.mm and above Mtr. 289.80
(iii)When cable laid in a HDPE pipe
33 / 11 KV 3C x 300 Sq.mm cable Mtr. 391.00
Add Cost of 200 HDPE pipe
(a) PN4 HDPE pipe(IS-4984) Mtr. 364.32
(b) HDPE DWC pipe(IS-14930) Mtr. 227.70
33/11 KV below 3X300 Sq.mm cable Mtr. 351.44
LT 3.5 core Sq qmm. Mtr. 352.36
Add Cost of 200 HDPE pipe
(i)PN4 HDPE pipe(IS-4984) Mtr. 250.47
(ii)HDPE DWC pipe(IS-14930) Mtr. 163.94
When cable laying through manual trench less (Bogie)
(i) 33/11 KV 3CX300 Sqmm. Cable Mtr. 223.48
(ii)33/11 KV below 3CX300 Sqmm. Mtr. 186.24
(iii) LT 3.5 core 95 Sqmm and above Mtr. 186.24
Cost of pipe shall be extra as above
20.8 Laying of under ground LT XLPE cable including excavation of 30cmx120cm.deep trench
in Kachha land and refilling by 25 cm thick layer of sand 'A' class bricks covering refiling
soil in the remaining portion.
20.10 Installation of cable termination/ straight through joints on LT XLPE/ PVC insulated Cable
with outdoor or straight through joint including required excavation/ remoral/ fixing/ refixing/
testing etc. as required.
A) (i) Outdoor and terminal 3.5 C/ 4 C x 50 Sq mm to 3.5 C/ 4 C x 185 Sq mm Nos 702.12
(ii) 3.5 C/ 4 C 240 Sq mm to 3.5 C/ 4 C x 400 Sq mm Nos 819.12
B) (i) Straight through 3.5 C/ 4 C x 50 Sq mm to 3.5 C/ 4 C x 185 Sq mm Nos 1462.63
(ii) 3.5 C/ 4 C 240 Sq mm to 3.5 C/ 4 C x 400 Sq mm Nos 1706.47
20.11 Installation of out door cable termination on 11 KV Aerial Bunched Cable including
requiredremoval/ fixing/ refixing/ testing etc. as required.
A Outdoor and terminal 50 Sq mm to 95 Sq mm Nos 351.05
20.12 Installation of straight through joints on HT XLPE Insulated Cable with straight through joint
including required remoral/ fixing/ refixing/ testing etc. as required. (Without excavation)
A For 11 KV:-
i Straight through joint 3x35 to 3x185 Sq mm Nos 1316.46
ii 3x240 Sq mm to 3x400 Sq mm Nos 1535.85
B For 33 KV:-
i Straight through joint 3x50 to 3x185 Sq mm Nos 1645.53
ii 3x240 Sq mm to 3x400 Sq mm Nos 2011.11
20.13 For assisting in cable fault location detailed as below by engaging the services of skilled Per 8 Hrs. 230.00
person on cable fault locating machine.
20.13 For Extra Loop (Ghera) to be provided near the pole on termination point and the length
ofcable along the pole for mounting of cable jointing kit.
a 11 KV Cable:-
3x35 Sq mm to 3x185 Sq mm Per Mtr 93.47
3x240 Sq mm to 3x400 Sq mm Per Mtr 105.16
b 33 KV Cable:-
3x50 Sq mm to 3x185 Sq mm Per Mtr 210.31
3x240 Sq mm to 3x400 Sq mm Per Mtr 227.84
Note:- 1. The rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra by
Nigam if applicable.
2. If the Cable Jointing Kits of HT/ LT are not available with Nigam, then the unit officer will obtain NAC
from ACOS & the contractor will supply the same as per latest SIR plus 10 % (profit) of approved vendors.
[48]
CHAPTER-21
ERECTION AND COMMISSIONING OF CAPACITOR AND CAPACITOR BANK
1 2 3 4
ELECTRICAL & MECHANICAL WORK( Capacitor Bank)
21.1 Installation of control panel including wiring to the required equipments Nos. 1883.68
and conducting all precommissioning tests before energization
satisfactory operation in all respect existing thereof.
21.2 Erection and assembly of capacitor bank, with RTV, Series Reactor on Set 10776.59
the structure as per approved drawing and installation,commssioning of
capacitor units, SR & RTV on erected structure including connections
and accessories, jumpering etc. as per approved drawing.
21.3 Laying, testing, termination of control cable, 1100 Volt PVC installed
supply and providing of ferrules and copper lugs to designate various
cores of control cable by terminal numbers for identification including
utilization of cable glands. The control cable should be neatly arranged
in trenches avoiding crossings, including clamping of control cable in
rubber battons at regular interval and providing identity tages.
NOTE: The rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid
extra by Nigam if applicable.
AEN-TW XEN(TW-II) Sr. A.O.(TW) SE(TW)
[49]
CHAPTER-22
LABOUR
1 2 3 4
1 Distribution of Energy bills (DL, NDS, Street light SIP, mix load & Ag)
Urban 1.51
Rural 1.95
2 Distribution of DC. Notices
Urban 2.41
Rural 6.02
NOTICE: Contractor should take receipt from consumers with dated
Signature for which book will be supplied by Nigam.
3 Photo state copies, (Including paper, ink & operator).(If contractor install his
m/c inside Nigam's Premises free accomodation and free electricity will be
provided by Nigam.
6 Disconnection/ Reconnection:-
(i) From Pole:- Per 41.40
Connection
(ii) From Meter:- Per 18.40
Connection
7 Site survey for preparing the estimate along details of connected Per 92.00
connections with their load and preparation of single line diagram. Connection
8 Energy Meter reading
8.1 Taking meter reading without photo Per Meter 3.53
8.2 Verification of meter reading with capturing photo of meter dial Per Meter 3.68
22.5 Identification numbering on support pole/structure/transformer/other
equipment/Warning instruction of availability of two sources of supply on
same structure, at source sturcture, at cut points, properly labelled using
yellow base and black indication marks (number or digits) 40/50 mm height
digits/ words should be used for this purpose. Base shall be made using 2
new or more coats of yellow enamel paint till good surface finish. Base
painting and marking of digits should be performed by a skilled and trained
painter using branded enamel paint.
Engineer- Incharge shall approve type and brand of enamel
paint.
22.5.1 In urban area Nos. 9.20
22.5.2 In rural area Nos. 11.04
Note:-The rates are inclusive of all applicable Taxes/ Duty except service tax which will be paid extra by
Nigam if applicable.
[50]
CHAPTER-23(A)
HIRE CHARGES OF PLANTS AND MACHINERIES
[51]
Chapter Name of machine For Deptt. Work
Code without Idle
No. P.O.L. Rs. Rs.
1 2 3 4
23.6 STONE CRUSHERS & GRANULATORS
23.6.1 Stone Crusher 30"x16" 847.49 286.87
23.6.2 Stone Crusher 16"x9" 534.58 234.66
23.6.3 Granulator 16"x5" 515.03 234.66
23.7 WATER PUMPS
23.7.1 Pumping set 5-9 HP 123.86 97.78
23.7.2 Pumping set 10-19 HP 143.42 104.30
23.7.3 Pumping set 20-30 HP 143.42 104.30
23.7.4 Pumping set above 30 HP 345.52 130.38
23.8 GENERATORS
23.8.1 Generating set upto 5 KVA 162.97 104.28
23.8.2 Generating set 5-15 KVA 202.07 117.33
23.8.3 Generating set above 15 KVA but below 50 KVA 345.51 130.38
23.9 AIRCOMPRESSORS
23.9.1 Aircompressor upto 115 cfm 378.10 143.43
23.9.2 Air compressor above 115 cfm. 417.25 143.43
23.10 BORING MACHINE
23.10.1 Boring machine other than diamond core 286.87 189.09
23.10.2 Diamond core drilling m/d 932.23 606.26
23.11 OTHER MACHINES
23.11.1 Mobile Crane 3 ton 801.85 273.82
23.11.2 Power winch 273.82 123.88
23.11.3 Front end loader 573.67 234.66
23.11.4 Hydraulic scraper 273.82 189.09
23.11.5 Chainpulley Block 13.05 2.58
23.11.6 Grouting machine 52.14 0.00
23.11.7 Vibrators 104.28 104.03
23.12 HIRE CHARGES OF EARTH MOVING
MACHINERY HOURLY BASIS
23.12.1 Bull Dozer 180/200 HP 444.48/p.hr. 207.43/p.hr.
[52]
Chapter Name of machine For Deptt. Work
Code without Idle
No. P.O.L. Rs. Rs.
1 2 3 4
23.13 Jeep/Bolero/max Mahindra/ Ambassador and equivalent
with the cubic capacity of at least 1800 CC, diesel version
without A.C with driver and R&M with a minimum average of
12 Kms. per litre excluding diesel oil and lubricant ( 1 litre oil
for 1000 Km).Vehicle should not be more than 5 year old
(designation up to Executive Engineer).
23.18 hiring of Tempo vehicle like TATA ACE above 800 CC etc.
Without POL.
(a) For 24 Hrs. a day 567.42
(b) For 12 Hrs. a day 327.85
(c) For 8 Hrs. a day 315.23
NOTE: -The Rates are inclusive of all applicable Taxes/ Duty except service tax which will be
paid extra by Nigam if applicable.
[53]
CHAPTER-23(B)
HIRE CHARGES OF PLANTS AND MACHINERIES
NOTE: -The Rates are inclusive of all applicable Taxes/ Duty except service tax
which will be paid extra by Nigam if applicable.
REPLACEMENT OF 11 KV CT PT SETS
1 2 3 4
24.2 Safe unloading of new /old 11 KV CT PT set (all sizes ) Set 52.66
NOTE: The Rates are inclusive of all applicable Taxes/ Duty except service tax which
will be paid extra by Nigam if applicable.
25.1 Supply of PVC ISI mark 1100 V 12x2.5 mm 2 solid copper armoured control Mtr. 218.69
cable including lugs & fersules and laying of cable along the DP structure
binding with wire at regular interval and making connections from CTPT
secondary terminals to TTB. Including utilization of cable gland
Note:-
1 The Concerned Assistant Engineer will arrange the necessary shut down for starting the
work. The installed meter inside the meter box and metering equipments duly mounted on the
mounting structure will be powered up by connecting load in the presence of Assistant
Engineer (O&M). Since the work invloves higher A/C voltage level the contractor shall take
fulcare regarding safety nors so as to avoid any accidental hazards
2 For the work under this chapter conductor, clamps & lugs for jumpring shall be provided by
contractor for which payment shall be made as per latest store
3 The rates are inclusive of all applicable taxes/duty except service tax which will be paid extra
by Nigam, if applicable.
1 2 3 4
25.1 Safe carriage of CT/PT set (all size) including loading and unloading from Nigam
store to site
25.1.1 (a) Within 10 Kms. Nos 178.65
25.1.2 (b) Above 10 Km upto 30 Km. Add for each Km. or part there off Nos 5.11
25.1.3 (c) Above 30 Km. Add for each Km. or part there off Nos 3.46
25.2 Installation, testing as per Nigam norms and commissioning of new CT/PT set on Nos 521.03
erected supports including jumpering wiring crimping of lugs clamping earth
connection of body and conducting pre commissioning test before energisation and
satisfactory operation in all respect. CTPT set shall be provided by Nigam from
concern sub-div stores.
25.3 Fixing of PVC ISI mark 1100 V 12x2.5 mm2 solid copper armoured control cable Mtr. 39.94
including lugs & fersules and laying of cable along the DP structure binding with wire
at regular interval and making connections from CTPT secondary terminals to TTB.
Including utilization of cable gland
25.4 Transportation and Fixing of fabricated steel item of MS Channel/Angle/Flat. Kg. 2.76
25.5 Transportation and Fixing MS nuts & bolts Kg. 2.76
25.6 Transportation and Fixing of meter box of size 525x300x150 mm made by deep Nos 205.59
drawn method from steel sheet of thickness 1.0 mm duly grey colour powder coated.
The viewing window shall be provided with toughened glass of 5 mm thickness of size
120x140 mm. The cover of meter box shall be fixed on inside hinges. The cover shall
be provided with neoprene rubber gasket lining fixed with adhessive. Backelite sheet
of size 450x275x2 mm for mounting of HTTVM and TTB shall be provided. 4 nos.
fixing clamps welded at top of rear face of the meter box of size 50x120x6 mm with 80
mm projection with a rectanguler slot of 17.5mmx50mm. 2 nos. clampsof 50x6mm
alongwith nuts, bolts & washers should also provided for fixing the box on pole/joist.
2 nos. welded sealing bolts with nuts and washers should be provided for sealing the
box . One hole with matel gland for cable size of 12core 2.5 mm2 control cable
should be provided in the center of bottom. The meter box should consist of one 3
phase 4 wire link type meter test termianl block of IMP/CAPITAL make rated for
atleast 10 A with cover mounted in the box. Earthing arrangement should be provided
one meter box.
25.7 Transportation and Installation of HTTVM in the meter box and making connection Nos 64.38
from TTB to HTTVM by 2.5 Sq. mm flexible ISI mark PVC wire (the flexible wire of
length 2 Mtr. for each HTTVM & TTB connection is to be supplied by the
contractor).HTTVM shall be provided by Nigam from concern stores.
Note:- The rates are inclusive of all applicable taxes/duty except service tax which will be paid extra by
Nigam, if applicable.
[57]
STANDARD DATA
[62]
Rates of CLRC increased as per variation in the labour index as per detail as
under
Factor= [0.2+0.05*(42.90/36.92)+0.75*(145/107.33)]
= 1.271
Say 27.1 % increase
Variation taken 75 % on labour charges ,20 % fixed charges and 5% on
transpotation charges
Factor= [0.2+0.35*(42.90/36.92)+0.45*(145/107.33)]
= 1.215
Say 21.5 % increase
Variation taken 35% on Deisel charges ,20 % fixed charges and 45% on
labour charges
Rates of CLRC increased as per variation in the labour index as per detail as
under
Factor= [0.2+0.10*(42.90/36.92)+0.70*(145/107.33)]
= 1.262
Say 26.2% increase
Variation taken 70 % on labour charges ,20 % fixed charges and 10% on
transpotation charges
Factor= [0.2+0.4*(42.90/36.92)+0.4*(145/107.33)]
= 1.205
Say 20.5 % increase
Variation taken 40% on Deisel charges ,20 % fixed charges and 40% on
labour charges
Rates of CLRC increased as per variation in the labour index as per detail as under
Factor= [0.1+0.15*(42.90/36.92)+0.75*(145/107.33)]
= 1.288
Say 28.8 % increase
Variation taken 75 % on labour charges ,10 % fixed charges and 15% on
transpotation charges
Factor= [0.1+0.45*(42.90/36.92)+0.45*(145/107.33)]
= 1.231
Say 23.1 % increase
Variation taken 45% on Deisel charges ,10 % fixed charges and 45% on labour
charges
In case of inspection vehicles since diesel is being provided by the Nigam as such no variation for
diesel prices can be allowed the factor therefore works out as under:
Factor = [0.1+0.45+0.45*(145/107.33)]
= 1.1579