Professional Documents
Culture Documents
Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements For
Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements For
A
1. Scope* These designations refer to the latest issue of the respective specifications,
which appear either in the Annual Book of ASTM Standards, Vol 01.05, or as
1.1 This specification2 covers a group of common require- reprints obtainable from ASTM.
ments which, unless otherwise specified in the purchase order 1.2 In case of any conflict in requirements, the requirements
or in an individual specification, shall apply to carbon and alloy of the purchase order, the individual material specification, and
steel bars under each of the following ASTM specifications (or this general specification shall prevail in the sequence named.
under any other ASTM specification which invokes this
1.3 The values stated in inch-pound units or SI units are to
specification or portions thereof):
be regarded as the standard. Within the text, the SI units are
Title of Specification ASTM
DesignationA
shown in brackets. The values stated in each system are not
Hot-Rolled Carbon Steel Bars: exact equivalents; therefore, each system must be used inde-
Steel Bars, Carbon, Quenched and Tempered A321 pendently of the other. Combining values from the two systems
Steel Bars and Shapes, Carbon Rolled from “T’’ Rails A499
Steel Bars, Carbon, Merchant Quality, M-Grades A575
may result in nonconformance with the specification.
Steel Bars, Carbon, Hot-Wrought, Special Quality A576 1.4 For purposes of determining conformance to this speci-
Steel Bars, Carbon, Merchant Quality, Mechanical A663/A663M
Properties fication and the various material specifications referenced in
Steel Bars, Carbon, Hot-Wrought, Special Quality, Me- A675/A675M 1.1, dimensional values shall be rounded to the nearest unit in
chanical Properties the right-hand place of figures used in expressing the limiting
Steel Bars for Springs, Carbon and Alloy A689
Cold-Finished Carbon Steel Bars: values in accordance with the rounding method of Practice
Steel Bars, Carbon and Alloy, Cold-Finished A108 E29.
Cold-Drawn Stress-Relieved Carbon Steel Bars Sub- A311/A311M
ject to Mechanical Property Requirements NOTE 1—Specification A29 previously listed dimensional tolerances for
Hot-Rolled Alloy Steel Bars: cold-finished bars; these are now found in Specification A108.
Steel Bars, Alloy, Standard Grades A322
Carbon and Alloy Steel Bars Subject to End-Quench A304 2. Referenced Documents
Hardenability Requirements
Steel Bars, Alloy, Hot-Wrought or Cold-Finished, A434 2.1 ASTM Standards:3
Quenched and Tempered
Steel Bars, Alloy, Hot-Wrought, for Elevated Tempera- A739
A108 Specification for Steel Bar, Carbon and Alloy, Cold-
ture or Pressure-Containing Parts, or Both Finished
Cold-Finished Alloy Steel Bars: A304 Specification for Carbon and Alloy Steel Bars Subject
Steel Bars, Alloy, Hot-Rolled or Cold-Finished, A434
Quenched and Tempered
to End-Quench Hardenability Requirements
Steel Bars, Carbon, Hot-Wrought or Cold-Finished, A696 A311/A311M Specification for Cold-Drawn, Stress-
Special Quality, for Pressure Piping Components Relieved Carbon Steel Bars Subject to Mechanical Prop-
erty Requirements
A321 Specification for Steel Bars, Carbon, Quenched and
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Tempered
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A322 Specification for Steel Bars, Alloy, Standard Grades
A01.15 on Bars.
Current edition approved May 1, 2012. Published May 2012. Originally
3
approved in 1957. Last previous edition approved in 2011 as A29/A29M – 11a. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/A0029_A0029M-12. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-29/SA-29M in Section II of that Code. the ASTM website.
Grade Designation Former Designation Carbon Manganese Phosphorous, max Sulfur, max
1513 ... 0.10–0.16 1.10–1.40 0.040 0.050
1518 ... 0.15–0.21 1.10–1.40 0.040 0.050
1522 ... 0.18–0.24 1.10–1.40 0.040 0.050
1524 1024 0.19–0.25 1.35–1.65 0.040 0.050
1525 ... 0.23–0.29 0.80–1.10 0.040 0.050
1526 ... 0.22–0.29 1.10–1.40 0.040 0.050
1527 1027 0.22–0.29 1.20–1.50 0.040 0.050
1536 1036 0.30–0.37 1.20–1.50 0.040 0.050
1541 1041 0.36–0.44 1.35–1.65 0.040 0.050
1547 ... 0.43–0.51 1.35–1.65 0.040 0.050
1548 1048 0.44–0.52 1.10–1.40 0.040 0.050
1551 1051 0.45–0.56 0.85–1.15 0.040 0.050
1552 1052 0.47–0.55 1.20–1.50 0.040 0.050
1561 1061 0.55–0.65 0.75–1.05 0.040 0.050
1566 1066 0.60–0.71 0.85–1.15 0.040 0.050
1572 1072 0.65–0.76 1.00–1.30 0.040 0.050
Heat Chemical Ranges and Limits, percent
Merchant Quality M Series Carbon Steel Bars
Grade Designation Carbon ManganeseG Phosphorous, max Sulfur, max
M 1008 0.10 max 0.25–0.60 0.04 0.05
M 1010 0.07–0.14 0.25–0.60 0.04 0.05
M 1012 0.09–0.16 0.25–0.60 0.04 0.05
M 1015 0.12–0.19 0.25–0.60 0.04 0.05
M 1017 0.14–0.21 0.25–0.60 0.04 0.05
M 1020 0.17–0.24 0.25–0.60 0.04 0.05
M 1023 0.19–0.27 0.25–0.60 0.04 0.05
M 1025 0.20–0.30 0.25–0.60 0.04 0.05
M 1031 0.26–0.36 0.25–0.60 0.04 0.05
M 1044 0.40–0.50 0.25–0.60 0.04 0.05
A
Maximum unless otherwise indicated.
B
When silicon is required, the following ranges and limits are commonly specified: 0.10 %, max, 0.10 % to 0.20 %, 0.15 % to 0.35 %, 0.20 % to 0.40 %, or 0.30 % to
0.60 %.
C
Copper can be specified when required as 0.20 % minimum.
D
When lead is required as an added element to a standard steel, a range of 0.15 to 0.35 % inclusive is specified. Such a steel is identified by inserting the letter “L”
between the second and third numerals of the grade designation, for example, 10 L 45. A cast or heat analysis is not determinable when lead is added to the ladle stream.
E
When boron treatment for killed steels is specified, the steels can be expected to contain 0.0005 to 0.003 % boron. If the usual titanium additive is not permitted, the
steels can be expected to contain up to 0.005 % boron.
F
The elements bismuth, calcium, selenium, or tellurium may be added as agreed upon between purchaser and supplier.
G
Unless prohibited by the purchaser, the manganese content may exceed 0.60 % on heat analysis to a maximum of 0.75 %, provided the carbon range on heat analysis
has the minimum and maximum reduced by 0.01 % for each 0.05 % manganese over 0.60 %.
4.2.1 The chemical composition of each heat or cast shall be 4.2.4 Reporting of significant figures and rounding shall be
determined by the manufacturer in accordance with Test in accordance with Test Methods, Practices, and Terminology
Methods, Practices, and Terminology A751. A751.
4.2.2 The heat or cast analysis shall conform to the require-
ments specified in the product specification or purchase order. 4.3 Product Analysis:
These can be the heat chemical range and limit for a grade 4.3.1 Merchant quality carbon bar steel is not subject to
designated in Tables 1 and 2, or another range and limit in rejection for product analysis unless misapplication of a heat is
accordance with 4.1.2, or with requirements of the product clearly indicated.
specification. 4.3.2 Analyses may be made by the purchaser from finished
NOTE 2—Heat analysis for lead is not determinable since lead is added bars other than merchant quality representing each heat of
to the ladle stream while each ingot is poured. When specified as an added open-hearth, basic-oxygen, or electric-furnace steel. The
element to a standard steel, the percentage of lead is reported as 0.15 to chemical composition thus determined shall not vary from the
0.35 incl, which is the range commonly specified for this element. limits specified in the applicable specification by more than the
4.2.3 If requested or required, the heat analysis shall be amounts prescribed in Table 5 and Table 6, but the several
reported to the purchaser or his representative. determinations of any element, excluding lead, in a heat may
4012 0.09–0.14 0.75–1.00 0.035 0.040 0.15 to 0.35 ... ... 0.15–0.25
4023 0.20–0.25 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4024 0.20–0.25 0.70–0.90 0.035 0.035–0.050 0.15 to 0.35 ... ... 0.20–0.30
4027 0.25–0.30 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4028 0.25–0.30 0.70–0.90 0.035 0.035–0.050 0.15 to 0.35 ... ... 0.20–0.30
4032 0.30–0.35 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4037 0.35–0.40 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4042 0.40–0.45 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4047 0.45–0.50 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.20–0.30
4118 0.18–0.23 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.40–0.60 0.08–0.15
4120 0.18–0.23 0.90–1.20 0.035 0.040 0.15 to 0.35 ... 0.40–0.60 0.13–0.20
4121 0.18–0.23 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.45–0.65 0.20–0.30
4130 0.28–0.33 0.40–0.60 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4135 0.33–0.38 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4137 0.35–0.40 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4140 0.38–0.43 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4142 0.40–0.45 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4145 0.43–0.48 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4147 0.45–0.50 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4150 0.48–0.53 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 0.15–0.25
4161 0.56–0.64 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 0.25–0.35
4320 0.17–0.22 0.45–0.65 0.035 0.040 0.15 to 0.35 1.65–2.00 0.40–0.60 0.20–0.30
4340 0.38–0.43 0.60–0.80 0.035 0.040 0.15 to 0.35 1.65–2.00 0.70–0.90 0.20–0.30
E4340 0.38–0.43 0.65–0.85 0.025 0.025 0.15 to 0.35 1.65–2.00 0.70–0.90 0.20–0.30
4419 0.18–0.23 0.45–0.65 0.035 0.040 0.15 to 0.35 ... ... 0.45–0.60
4422 0.20–0.25 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.35–0.45
4427 0.24–0.29 0.70–0.90 0.035 0.040 0.15 to 0.35 ... ... 0.35–0.45
4615 0.13–0.18 0.45–0.65 0.035 0.040 0.15 to 0.35 1.65–2.00 ... 0.20–0.30
4620 0.17–0.22 0.45–0.65 0.035 0.040 0.15 to 0.35 1.65–2.00 ... 0.20–0.30
4621 0.18–0.23 0.70–0.90 0.035 0.040 0.15 to 0.35 1.65–2.00 ... 0.20–0.30
4626 0.24–0.29 0.45–0.65 0.035 0.040 0.15 to 0.35 0.70–1.00 ... 0.15–0.25
4715 0.13–0.18 0.70–0.90 0.035 0.040 0.15 to 0.35 0.70–1.00 0.45–0.65 0.45–0.60
4718 0.16–0.21 0.70–0.90 0.035 0.040 0.15 to 0.35 0.90–1.20 0.35–0.55 0.30–0.40
4720 0.17–0.22 0.50–0.70 0.035 0.040 0.15 to 0.35 0.90–1.20 0.35–0.55 0.15–0.25
4815 0.13–0.18 0.40–0.60 0.035 0.040 0.15 to 0.35 3.25–3.75 ... 0.20–0.30
4817 0.15–0.20 0.40–0.60 0.035 0.040 0.15 to 0.35 3.25–3.75 ... 0.20–0.30
4820 0.18–0.23 0.50–0.70 0.035 0.040 0.15 to 0.35 3.25–3.75 ... 0.20–0.30
5015 0.12–0.17 0.30–0.50 0.035 0.040 0.15 to 0.35 ... 0.30–0.50 ...
5046 0.43–0.48 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.20–0.35 ...
5115 0.13–0.18 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5120 0.17–0.22 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5130 0.28–0.33 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 ...
5132 0.30–0.35 0.60–0.80 0.035 0.040 0.15 to 0.35 ... 0.75–1.00 ...
5135 0.33–0.38 0.60–0.80 0.035 0.040 0.15 to 0.35 ... 0.80–1.05 ...
5140 0.38–0.43 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5145 0.43–0.48 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5147 0.46–0.51 0.70–0.95 0.035 0.040 0.15 to 0.35 ... 0.85–1.15 ...
5150 0.48–0.53 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5155 0.51–0.59 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
5160 0.56–0.64 0.75–1.00 0.035 0.040 0.15 to 0.35 ... 0.70–0.90 ...
E50100 0.98–1.10 0.25–0.45 0.025 0.025 0.15 to 0.35 ... 0.40–0.60 ...
E51100 0.98–1.10 0.25–0.45 0.025 0.025 0.15 to 0.35 ... 0.90–1.15 ...
E52100 0.98–1.10 0.25–0.45 0.025 0.025 0.15 to 0.35 ... 1.30–1.60 ...
52100B 0.93–1.05 0.25–0.45 0.025 0.015 0.15 to 0.35 ... 1.35–1.60 ...
6118 0.16–0.21 0.50–0.70 0.035 0.040 0.15 to 0.35 ... 0.50–0.70 (0.10–0.15 V)
6150 0.48–0.53 0.70–0.90 0.035 0.040 0.15 to 0.35 ... 0.80–1.10 (0.15 min V)
8115 0.13–0.18 0.70–0.90 0.035 0.040 0.15 to 0.35 0.20–0.40 0.30–0.50 0.08–0.15
8615 0.13–0.18 0.70–0.90 0.035 0.040 0.15 to 0.35 0.40–0.70 0.40–0.60 0.15–0.25
8617 0.15–0.20 0.70–0.90 0.035 0.040 0.15 to 0.35 0.40–0.70 0.40–0.60 0.15–0.25
E9310 0.08–0.13 0.45–0.65 0.025 0.025 0.15 to 0.30 3.00–3.50 1.00–1.40 0.08–0.15
Standard Boron SteelsC
50B44 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.20–0.60 ...
50B46 0.44–0.49 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.20–0.35 ...
50B50 0.48–0.53 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.40–0.60 ...
50B60 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.40–0.60 ...
51B60 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
81B45 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 0.20–0.40 0.35–0.55 0.08–0.15
94B17 0.15–0.20 0.75–1.00 0.035 0.040 0.15–0.35 0.30–0.60 0.30–0.50 0.08–0.15
94B30 0.28–0.33 0.75–1.00 0.035 0.040 0.15–0.35 0.30–0.60 0.30–0.50 0.08–0.15
A
Silicon may be specified by the purchaser as 0.10 % maximum. The need for 0.10% maximum generally relates to severe cold-formed parts.
B
The purchaser may also require the following maximums: copper 0.30 %; aluminum 0.050 %; oxygen 0.0015 %.
C
These steels can be expected to contain 0.0005 to 0.003 % boron. If the usual titanium additive is not permitted, the steels can be expected to contain up to 0.005 %
boron.
not vary both above and below the specified range. Rimmed or 4.3.3.4 When the steel is subject to tension test require-
capped steel is characterized by a lack of homogeneity in its ments, the tension test specimen can also be used for product
composition, especially for the elements carbon, phosphorus, analysis. In that case, chips for product analysis can be taken
and sulfur; therefore, when rimmed or capped steel is specified by drilling entirely through the tension test specimens or by the
or required, the limitations for these elements shall not be method described in 4.3.3.1.
applicable. Because of the degree to which phosphorus and 4.3.4 When chips are taken by drilling, the diameter of the
sulfur segregate, the limitations for these elements shall not be drill used shall conform to the following:
applicable to rephosphorized or resulfurized steels. Area of Sample Cross Section, Approximate Drill Diameter,
4.3.3 Samples for product analysis shall be taken by one of in. 2 (cm2) in. (mm)
16 [100] or less 1⁄2 [12.5]
the following methods:
Over 16 [100] 1 [25.0]
4.3.3.1 Applicable to small sections whose cross-sectional
area does not exceed 0.75 in.2 [500 mm2] such as rounds, 4.3.5 The minimum number of samples to be taken from
squares, hexagons, and the like. Chips are taken by milling or material representing the same heat or lot before rejection by
machining the full cross section of the piece. Drilling is not a the purchaser shall be as follows:
feasible method for sampling sizes 0.75 in.2 and smaller. Minimum Number of Samples
15 tons [15 Mg] and under 4
4.3.3.2 Applicable to products where the width of the cross Over 15 tons [15 Mg] 6
section greatly exceeds the thickness, such as bar size shapes
and light flat bars. Chips are taken by drilling entirely through 4.3.6 In case the number of pieces in a heat is less than the
the steel at a point midway between the edge and the middle of number of samples required, one sample from each piece shall
the section, or by milling or machining the entire cross section. be considered sufficient.
4.3.3.3 Applicable to large rounds, squares semifinished, 4.3.7 In the event that product analysis determinations are
etc. Chips are taken at any point midway between the outside outside the permissible limits as prescribed in 4.3.2, additional
and the center of the piece by drilling parallel to the axis or by samples shall be analyzed and the acceptability of the heat
milling or machining the full cross section. In cases where negotiated between the purchaser and the producer.
these methods are not practicable, the piece may be drilled on 4.4 Referee Analysis—In case a referee analysis is required
the side, but chips are not taken until they represent the portion and agreed upon to resolve a dispute concerning the results of
midway between the outside and the center. a chemical analysis, the referee analysis shall be performed in
SUPPLEMENTARY REQUIREMENTS
The following supplementary requirements shall apply only when specified by the purchaser in the
contract or order.
TABLE S1.1 Thickness and Width Tolerances for Hot-Wrought Square-Edge and Round-Edge Flat Bars Ordered to 0.3 mm Under
ToleranceA
NOTE 1—Tolerance under specified thickness 0.3 mm.
Tolerances over Specified Thickness for Thickness Given, mm Tolerance from Specified Width, mm
Specified Width, mm
Over 6 to 12, incl Over 12 to 25, incl Over 25 to 50, incl Over 50 to 75, incl Over 75 Over Under
To 25, incl ... ... ... ... ... 0.5 0.5
Over 25 to 50, incl ... 0.5 1.3 ... ... 1.0 1.0
Over 50 to 100, incl 0.5 0.7 1.3 2.1 2.1 1.5 1.0
Over 100 to 150, incl 0.5 0.7 1.3 2.1 2.1 2.5 1.5
Over 150 to 200, incl 0.5 1.0 1.3 2.1 2.9 3.0 2.5
A
When a square is held against a face and an edge of a square-edge flat bar, the edge shall not deviate by more than 3° or 5 % of the thickness.
ANNEXES
(Mandatory Information)
A
Steel bars are regularly cut to length by shearing or hot sawing, which can
cause end distortion resulting in those portions of the bar being outside the
applicable size tolerance. When this end condition is objectionable, a machine cut
end should be considered.
B
Out-of-hexagon or out-of-octagon is the greatest difference between any two
dimensions at the same cross section between opposite faces.
TABLE A1.3 Permissible Variations in Thickness and Width for Hot-Wrought Square Edge and Round Edge Flat BarsA
Permissible Variations in Thickness, for Thickness Given, Over and Under, in.B Permissible Variations in Width, in.
Specified
Width, in. 0.203 to 0.230, 0.230 to 1⁄4 , ⁄ to 1⁄2,
14 Over 1⁄2 to Over 1 to 2, Over 2 to 3, Over 3 Over Under
excl excl incl 1, incl incl incl
To 1, incl 0.007 0.007 0.008 0.010 ... ... ... ⁄
1 64 ⁄
1 64
Over 2 to 4, incl 0.008 0.008 0.015 0.020 1⁄32 3⁄64 3⁄64 1⁄16 1⁄32
Over 4 to 6, incl 0.009 0.009 0.015 0.020 1⁄32 3⁄64 3⁄64 3⁄32 1⁄16
C
Over 6 to 8, incl 0.015 0.016 0.025 1⁄32 3⁄64 1⁄16 1⁄8 3⁄32
A
When a square is held against a face and an edge of a square edge flat bar, the edge shall not deviate by more than 3° or 5 % of the thickness.
B
Steel bars are regularly cut to length by shearing or hot sawing, which can cause end distortion resulting in those portions of the bar being outside the applicable size
tolerance. When this end condition is objectionable, a machine cut end should be considered.
C
Flats over 6 to 8 in., incl, in width, are not available as hot-wrought steel bars in thickness under 0.230 in.
A
The longer leg of an unequal angle determines the size for tolerance. The
out-of-square tolerance in either direction is 11⁄2 °.
incl
Over 11⁄2 ⁄
1 16 ⁄
1 16 0.015 0.020 ⁄
1 32
to 3, excl
A
For channels 5⁄8 in. and under in depth, the out-of-square tolerance is 3⁄64
in./in. of depth.
B
Measurements for depth of section and width of flanges are overall.
TABLE A1.6 Permissible Variations in Dimensions for Hot-Wrought Bar Size Tees of Carbon Steel
Permissible Variations in Size, in.
Specified Size of
Width or DepthB Thickness of Flange Thickness of Stem Stem out-of-
Tee, in.A
Over Under Over Under Over Under SquareC
To 11⁄4 , incl 3⁄64 3⁄64 0.010 0.010 0.005 0.020 1⁄ 32
Over 11⁄4 to 2, incl 1⁄16 1⁄16 0.012 0.012 0.010 0.020 1⁄16
A
The longer member of the unequal tee determines the size for tolerances.
B
Measurements for both width and depth are overall.
C
Stem out-of-square is the variation from its true position of the center line of the stem measured at the point.
TABLE A1.8 Permissible Variations in Length for Hot-Wrought Rounds, Squares, Hexagons, Flats, and Bar Size Sections of Steel
Specified Size of Specified Size of Flats, in. Permissible Variations Over Specified Length, in.A
Rounds, Squares,
and Hexagons, in. Thickness Width 5 to 10 ft, excl 10 to 20 ft, excl 20 to 30 ft, excl 30 to 40 ft, excl 40 to 60 ft, excl
Mill Shearing
To 1, incl to 1, incl to 3, incl ⁄
12 ⁄
34 1 1⁄4 1 3⁄ 4 2 1 ⁄4
Over 1 to 2, incl over 1 to 3, incl 5⁄ 8 1 1 1⁄2 2 2 1 ⁄2
to 1, incl over 3 to 6, incl 5⁄ 8 1 1 1⁄2 2 2 1 ⁄2
Over 2 to 5, incl over 1 over 3 to 6, incl 1 11⁄2 1 3⁄4 2 1⁄ 4 2 3 ⁄4
Over 5 to 10, incl ... ... 2 21⁄2 2 3⁄4 3 3 1 ⁄4
0.230 to 1, incl over 6 to 8, incl 3⁄ 4 1 1⁄ 4 1 3⁄4 3 1⁄ 2 4
over 1 to 3, incl over 6 to 8, incl 11⁄4 1 3⁄ 4 2 3 1⁄ 2 4
Bar Size Sections ... ... 5⁄ 8 1 1 1⁄2 2 2 1 ⁄2
Hot Sawing
B
2 to 31⁄2 , incl 1 and over 3 and over 1 1⁄ 2 1 3⁄4 2 1⁄ 4 2 3 ⁄4
Over 31⁄2 to 5, incl 2 21⁄4 2 5⁄ 8 3
B
Over 5 to 10, incl ... ... 2 1⁄ 2 2 3⁄4 3 3 1 ⁄4
A
No permissible variations under.
B
Smaller sizes and shorter lengths are not hot sawed.
Over 3 to 6, incl ⁄
5 16 ⁄
7 16
A
No tolerance under.
A
Because of warpage, straightness tolerances do not apply to bars if any
subsequent heating operation or controlled cooling has been performed.
TABLE A2.1 Tolerances in Sectional Dimensions for Round and Square Bars and Round-Cornered Square Bars
Tolerance from Out-of-Round, or
Size, mm Specified Size, Over Out-of-Square
and Under, mm or %A Section,B mm or %A
To 7, incl 0.13 mm 0.20 mm
Over 7 to 11, incl 0.15 mm 0.22 mm
Over 11 to 15, incl 0.18 mm 0.27 mm
Over 15 to 19, incl 0.20 mm 0.30 mm
Over 19 to 250, incl 1% 1.5 %
A
The tolerance shall be rounded to the nearest tenth of a millimetre after calculation.
B
Out-of-round is the difference between the maximum and the minimum diameters of the bar, measured at the same cross section. Out-of-square is the difference in
the two dimensions at the same cross section of a square bar between opposite faces.
TABLE A2.2 Tolerances in Cross Section for Hot-Wrought Hexagonal and Octagonal Steel Bars
Out of
Tolerance from Specified Size, mm Hexagon or
Specified Size Between
Out of
Opposite Sides, mm
Over Under Octagon,
mmA
To 13, incl 0.18 0.18 0.3
Over 13 to 25, incl 0.25 0.25 0.4
Over 25 to 40, incl 0.55 0.35 0.6
Over 40 to 50, incl 0.8 0.40 0.8
Over 50 to 65, incl 1.2 0.40 1.2
Over 65 to 80, incl 1.6 0.40 1.6
Over 80 to 100, incl 2.0 0.40 2.0
A
Out of hexagon or out of octagon is the greatest difference between any two dimensions at the cross section between opposite faces.
TABLE A2.3 Thickness and Width Tolerances for Hot-Wrought Square-Edge and Round-Edge Flat BarsA,B
Tolerances from Specified Thickness for Thickness Given Over and Under, mm Tolerances from Specified
Width, mm
Specified Width, mm
Over 5 to 6, incl Over 6 to 12, Over 12, to 25, Over 25 to 50, Over 50 to 75
Over 75 Over Under
incl incl incl
To 25, incl 0.18 0.20 0.25 ... ... ... 0.5 0.5
Over 25 to 50, incl 0.18 0.30 0.40 0.8 ... ... 1.0 1.0
Over 50 to 100, incl 0.20 0.40 0.50 0.8 1.2 1.2 1.5 1.0
Over 100 to 150, incl 0.25 0.40 0.50 0.8 1.2 1.2 2.5 1.5
A
Over 150 to 200, incl 0.40 0.65 0.8 1.2 1.6 3.0 2.5
A
When a square is held against a face and an edge of a square edge flat bar, the edge shall not deviate by more than 3° or 5 % of the thickness.
B
Flats over 150 to 200 mm, incl in width are not available as hot-wrought bars in thickness 6 mm and under.
TABLE A2.7 Permissible Variations in Dimensions for Half-Rounds, Ovals, Half-Ovals, and Other Special Bar Size Sections
Due to mill facilities, tolerances on half-rounds, ovals, and other special bar size sections vary among the manufacturers and such tolerances should be
negotiated between the manufacturer and the purchaser.
TABLE A2.8 Length Tolerances for Hot-Wrought Rounds, Squares, Hexagons, Octagons, Flats, and Bar Size Sections
Specified Size of Flats, mm Tolerances over Specified Length, mmA
Specified Size of Rounds, Thickness Width 1500 3000 6000 9000 12 000
Squares, Hexagons and to to to to to
Octagons, mm 3000, 6000, 9000, 12 000, 18 000,
excl excl excl excl excl
Hot Shearing
To 25, incl to 25, incl to 75, incl 15 20 35 45 60
Over 25 to 50, incl over 25 to 75, incl 15 25 40 50 65
to 25, incl over 75 to 150, incl 15 25 40 50 65
Over 50 to 125, incl over 25 over 75 to 150, incl 25 40 45 60 70
Over 125 to 250, incl ... ... 50 65 70 75 85
Bar Size Sections over 6 to 25, incl over 150 to 200, incl 20 30 45 90 100
over 25 to 75, incl over 150 to 200, incl 30 45 50 90 100
... ... 15 25 40 50 65
Hot Sawing
B
50 to 90, incl 25 and over 75 and over 40 45 60 70
Over 90 to 125, incl 50 60 65 75
B
Over 125 to 250, incl ... ... 65 70 75 85
A
No tolerance under.
B
Smaller sizes and shorter lengths are not hot sawed.
TABLE A2.10 Straightness Tolerances for Hot-Wrought Bars and Bar Size SectionsA
Standard Tolerances 6 mm in any 1500 mm and (length in mm/250)B
Special Tolerances 3 mm in any 1500 mm and (length in mm/500)B
A
Because of warpage, straightness tolerances do not apply to bars if any subsequent heating operation or controlled cooling has been performed.
B
Round to the nearest whole millimetre.
SUMMARY OF CHANGES
Committee A01 has identified the location of selected changes to this standard since the last issue
(A29/A29M – 11a) that may impact the use of this standard. (Approved May 1, 2012.)
Committee A01 has identified the location of selected changes to this standard since the last issue
(A29/A29M – 11) that may impact the use of this standard. (Approved October 1, 2011.)
Committee A01 has identified the location of selected changes to this standard since the last issue
(A29/A29M – 05) that may impact the use of this standard. (Approved April 1, 2011.)
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).