Professional Documents
Culture Documents
Installation Instructions: Percy Single Control Monoblock and Vessel Faucet
Installation Instructions: Percy Single Control Monoblock and Vessel Faucet
®
Percy
Single Control Monoblock
and Vessel Faucet
Pixie Handle Monoblock - Model D3510510C
Loop Handle Monoblock - Model D3510512C
Pixie Handle Vessel - Model D3510515C
Loop Handle Vessel - Model D3510517C
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
U S E
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
F U T U R E
Flat Blade Screwdriver Channel Locks Adjustable Wrench
ROUGHING-IN DIMENSIONS:
• For reference
6-3/4" 2-7/16"
6-3/4" (171 mm) (63 mm) D.
(171 mm)
PIXIE LOOP
HANDLE HANDLE
8-13/16"
14-7/8"
(223 mm)
(378 mm)
F O R
9-9/16"
(243 mm)
4-1/2"
(114 mm) 3-5/8" MOUNTING
4-1/2" 2-1/4" (92 mm) SURFACE
14-1/8"
(114 mm) (57 mm)
(359 mm)
S A V E
8-15/16"
(227 mm)
1-1/2" 2"
(38 mm) MAX. (51 mm) MAX.
2-1/4" 20"
(57 mm) 12-1/2" (508mm)
(318 mm)
FLEXIBLE
1-1/4" OD
HOSES
(32 mm OD)
NOTE: MOUNTING HOLE 1-1/4" (32 mm) D. SUPPLY CONNECTIONS ARE 3/8" COMPRESSION
• Seat O-RING SEAL (1) into under side of FAUCET BASE (2).
• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through the mounting hole of lavatory
or mounting surface. Fig. A.
• From below, push GASKET (7) and RETAINING WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING
NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against mounting hole. Before final tightening, make sure collar
on MOUNTING NUT (6) is seated into RETAINING WASHER (5). Fig. B.
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete faucet mounting.
Fig. A.
2
1
GROOVE
(FAUCET BASE)
3
4
Fig. B.
MOUNTING SURFACE
7
5
6
COLLAR ON
MOUNTING NUT
4
8
2 4
2
1-1/4” O.D.
2
1
3/8" COMPRESSION
HOT COLD
• With HANDLE (1) in OFF position, remove AERATOR (3). Turn on WATER SUPPLIES (2) and check all connections for leaks.
• Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3).
ON
1 OFF
COLD
HOT
WASTE
OUTLET
“P” TRAP
2
11 CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CAM CAP
DISCONNECT CAM CAP
DISCONNECT
2
2
REMOVE
CAM CAP
REMOVE
CAM CAP
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed)
or “Unlock” Mode (Stopper is removable).
Unlocked Mode
Fig. J. CAM
Fig. K.
INSTALL CAM INSTALL
CAM CAP
Monoblock
Pixie Handle
D3510510C
Loop Handle
D3510512C
M964631-YYY0A
Vessel
LOOP HANDLE KIT Pixie Handle
(D3510512C, D3510517C)
D3510515C
Loop Handle
D3510517C
M964634-0070A M964632-YYY0A
MANIFOLD SEAL KIT PIXIE HANDLE KIT
(D3510510C, D3510515C)
M964635-YYY0A Monoblock
LIFT KNOB & ROD Faucet
(MONOBLOCK)
M964637-YYY0A
LIFT KNOB & ROD Vessel
(VESSEL) Faucet
M964636-0070A
AERATOR KIT
M964712-0070A
O-RING SEAL
M964638-0070A
MOUNTING KIT
874214.XXX
DRAIN ASSEMBLY
M952430-0070A
SPPED CONNECT®
ASSEMBLY
M921935-0070A
ADAPTOR