Professional Documents
Culture Documents
Operator'S Manual: Dgps Navigator Gps Navigator
Operator'S Manual: Dgps Navigator Gps Navigator
Operator'S Manual: Dgps Navigator Gps Navigator
DGPS NAVIGATOR
GPS NAVIGATOR
Model GP-37/GP-32
www.furuno.com
The paper used in this manual
is elemental chlorine free.
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
0 0 0 8 0 9 2 8 8 1 5
IMPORTANT NOTICES
General
• This manual has been authored with simplified grammar, to meet the needs of
international users.
• The operator of this equipment must read and follow the descriptions in this manual.
Wrong operation or maintenance can cancel the warranty or cause injury.
• Do not copy any part of this manual without written permission from FURUNO.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and equipment specifications can change without notice.
• The example screens (or illustrations) shown in this manual can be different from the
screens you see on your display. The screens you see depend on your system
configuration and equipment settings.
• Save this manual for future reference.
• Any modification of the equipment (including software) by persons not authorized by
FURUNO will cancel the warranty.
• The following concern acts as our importer in Europe, as defined in DECISION No
768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands
• All brand and product names are trademarks, registered trademarks or service marks of
their respective holders.
i
SAFETY INSTRUCTIONS
Safety Instructions for the Operator
WARNING NOTICE
Do not open the equipment. Be sure the power supply is compatible
with the equipment.
Only qualified personnel should work inside
the equipment. Incorrect power supply may cause the
equipment to overheat.
Do not disassemble or modify the
equipment. The useable temperature range for the
antenna unit is -25 C to 70 C ; -15 C to
Fire, electrical shock or serious injury can
55 C for the display unit.
result.
Use of the equipment out of those ranges
may damage the equipment.
Immediately turn off the power at the
switchboard if the equipment is
emitting smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
ii
Safety Instructions for the Installer
WARNING NOTICE
Do not open the cover unless totally Observe the following compass safe
familiar with electrical circuits and distances to prevent interference to a
service manual. magnetic compass:
iii
TABLE OF CONTENTS
iv
9. INSTALLATION ........................ 53 OUTLINE DRAWINGS ................ D-1
9.1 Installation of Display Unit ......... 53 INTERCONNECTION DIAGRAMS..S-1
9.2 Installation of Antenna Unit........ 54
9.3 Wiring ........................................ 55 INDEX ................................... Index-1
9.4 Initial Settings ............................ 56
Declaration of Conformity
APPENDIX ................................AP-1
SPECIFICATIONS..................... SP-1
v
FOREWORD
A Word to the Owner of the Features
GP-37, GP-32 The GP-37/GP-32 is a totally integrated GPS
Congratulations on your choice of the GP-37 receiver and video plotter, and mainly
DGPS Navigator, GP-32 GPS Navigator. consists of a display unit and an antenna unit.
The GP-37 is additionally equipped with a
Since 1948, FURUNO Electric Company has DGPS beacon receiver, built in the display
enjoyed an enviable reputation for innovative unit.
and dependable marine electronics
equipment. This dedication to excellence is The main features of the GP-37/GP-32 are
furthered by our extensive global network of
agents and dealers. • A DGPS beacon receiver may be
connected to the GP-32 to add DGPS
Your navigator is designed and constructed to capability.
meet the rigorous demands of the marine • WAAS capability.
environment. However, no machine can • Storage for 999 waypoints and 50 routes
perform its intended function unless installed, • Alarms: Arrival/Anchor Watch, XTE
operated and maintained properly. Please (Cross-track Error), Trip, Odometer, Time,
carefully read and follow the recommended WAAS/DGPS, and Speed.
procedures for installation, operation, and
• Man overboard feature records position at
maintenance.
time of man overboard and provides
continuous updates of range and bearing
We would appreciate hearing from you, the
when navigating to the MOB position.
end-user, about whether we are achieving our
purposes. • Bright 95 x 60 mm LCD with adjustable
contrast and brilliance.
Thank you for considering and purchasing • Autopilot (option) may be connected, and
FURUNO equipment. steering data output to the autopilot.
• Unique Highway display provides a graphic
presentation of ship’s progress toward a
Program No. waypoint.
2051547-*** (GP-32) • User displays definable by operator.
2051524-*** (GP-37)
• Waypoint and route data can be uploaded
** denotes minor modifications.
from a PC and downloaded to a PC.
CE Declarations
With regards to CE declarations, please refer
to our website (www.furuno.com), for further
information on RoHS conformity declarations.
vi
SYSTEM CONFIGURATION
Note: This equipment is intended for use on marine vessels. Do not use it in other applications.
ANTENNA UNIT
GPA-019
PROCESSOR UNIT*
FURUNO GPS NAVIGATOR
NAVIGATOR
PERSONAL COMPUTER
: Standard Supply
: Option
12/24 VDC
ANTENNA UNIT
GPA-017
PROCESSOR UNIT
FURUNO GPS NAVIGATOR
NAVIGATOR
DGPS BEACON RECEIVER
PERSONAL COMPUTER
: Standard Supply
: Option
12/24 VDC
This GPS receiver complies with Canadian standard RSS-210 (Low Power
License-Exempt Radio communication Devices).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
vii
EQUIPMENT LISTS
Standard supply
Name Type Qty Remarks
Display GP-37 With hanger, knob
1
Unit GP-32
Antenna GPA-019 1 For GP-37, w/10 m cable
Unit GPA-017 1 For GP-32, w/10 m cable
Installation CP20-02310 1 set • Power/data cable (1 pc.)
Materials (Type: MJ-A7SPF0009-020C, Code No.: 000-159-686-10)
• Tapping screw (4 pcs.)
(Type: 5X20, Code No.: 000-162-608-10)
Spare Parts SP20-01001 1 set Fuse (2 pcs.)
(Type: FGMB 125V 1A PBF, Code No.: 000-157-478-10)
Template C42-00201 1 Code No. 000-809-299, flush mounting template
Hard Cover FP14-02801 1 Code No. 004-366-960
Optional equipment
Name Type Code No. Qty Remarks
Right Angle NO.13-QA330 000-803-239 1 For mounting the antenna
Antenna Base unit, choose one
L-type Antenna NO.13-QA310 000-803-240 1
Base
Handrail NO.13-RC5160 000-806-114 1
Antenna Base
Mast Mounting CP20-01111 004-365-780 1 set
Kit
Cable Assy. MJ-A7SPF0009-020C 000-159-686-10 1
Flush Mounting OP20-29 000-041-405 1 set For flush mounting the
Kit F display unit, choose one
Flush Mounting OP20-17 000-040-720 1 set
Kit S
viii
1. OPERATIONAL OVERVIEW
1.1 Controls
Cursor Pad
• Shifts cursor (cursor displayed)
and display (cursor off).
• Selects items on menus.
Press once: Zoom, centering, • Enters alphanumeric data.
or escapes from current opera-
tion, depending on display in MENU ENT Registers items on menus.
use.
Press twice: Opens menu.
Chooses display mode. DISP GOTO Sets/cancels destination.
Control panel
How to attach and remove the hard cover
To attach the hard cover, set it to the display unit at an angle.
Press at arrows
and pull toward
you to remove.
1
1. OPERATIONAL OVERVIEW
The equipment shows receiver status Brilliance and contrast adjustment window
indication at the top left-hand corner in most
2. To adjust the brilliance, press ▲ or ▼.
display modes. The table below shows these
Current setting is shown to the right of ▲.
indications and their meanings.
Maximum setting is 8.
Receiver status indications 3. To adjust the contrast, press ◄ or ►.
Current setting is shown to the right of ►.
Indication Meaning Maximum setting is 63.
2D 2D GPS position fix 4. Press the [ENT] key to finish.
3D 3D GPS position fix
D2D 2D DGPS position fix Note: If the last-used contrast setting is 36 or
D3D 3D DGPS position fix higher, the equipment starts up with that
W2D 2D WAAS position fix setting. If the setting is 35 or lower, the
W3D 3D WAAS position fix equipment starts up with setting 36.
DOP* 2D: HDOP larger than 4
3D: PDOP larger than 6
SIM Simulation mode
2
1. OPERATIONAL OVERVIEW
20 D2D
n
10 30 [5 m]
SOG 0 9.9 KT
60
34°44.000N 135°21.000E
004
POWER(V) SOG(KT)
BRG 242° [+]
Note 1: The unit measures distances up to 9999 nm. Any distance greater than 9999 nm is
shown as “*999”.
Note 2: Position data can be shown in latitude and longitude or TDs (Loran C or Decca).
3
1. OPERATIONAL OVERVIEW
Plotter display
The plotter display traces own ship’s track, and shows position, bearing to cursor, range to
cursor, horizontal display range setting and receiver status.
Receiver status
(See table on page 2.) Own ship mark (blinking)
Plotter display
Highway display
The highway display provides a 3-D view of own ship’s progress toward destination (waypoint).
Nav data is also shown.
Course
over
COG 11° 0.5
0.3 0.5
Destination waypoint
Moves forward as boat
nears destination.
ground
RNG 9.0 n
m I I I
NI I I I
∆ C (Delta Course)
Speed
over
SOG 12.5 k
t
XTE
0.05 n
m
The boat mark displays
course as follows:
When no waypoint is set;
ground
The mode is North-up and
the arrow shows boat's course.
Range from Analog XTE (Cross-track error) scale When a waypoint is set;
own ship to Arrow shifts with boat's XTE. When the The arrow shows boat's
destination arrow is aligned with the centerline course towards destination.
waypoint the boat is on course. The arrow blinks if Digital XTE indication
boat's XTE is greater than XTE scale (in nautical miles)
range. "N" (North) is displayed instead of
the arrow when no destination is set.
Highway display
4
1. OPERATIONAL OVERVIEW
Steering display
The steering display provides steering information such as ship’s speed, course, range, bearing,
ETA and TTG.
Receiver status
Bearing reference (MAG or TRUE)
Destination (CURSOR or waypoint name)
Time
D2D MAG CURSOR 04:32 Bearing from own ship
▼ to destination
W 300 330 N 30 60 E Bearing scale
I I I I I I I I I I I I I
Speed over ground SOG: 12.5 kt COG: 354° Course over ground
Range from own ship RNG: 0.16 nm BRG: 60° Bearing
to destination
TTG: 1H 30M ETA: 12:30 Estimated Time of
Time-To-Go Arrival at destination
to destination (*9:*9 shown when
(*9H*9M is displayed ETA is over 99h59min.)
when TTG is over 99 h59min.)
Steering display
Nav data display
The nav data display shows receiver status, position in latitude and longitude (or TDs), course
over ground, speed over ground, date and time.
Receiver status
34°44.000' N
Position in latitude
and longitude
135°21.000' E
5
1. OPERATIONAL OVERVIEW
User displays
Two user displays are available, digital and speedometer.
Digital display
The digital display shows digital navigation data. The user may choose what data to display in
one to four cells. The choices of data are time, speed over ground, cross-track error, odometer
distance, position, course over ground, time-to-go to destination, trip distance, power source
voltage, range and bearing to waypoint, and estimated time of arrival at destination.
POWER(V) SOG(KT)
12.1 9.9
TRIP(NM) COG(°)
9.99 5.6
Digital display (default display)
Speedometer display
The speedometer display provides both digital and analog displays of speed over ground.
20
10 30
0 40
SOG 0 9.3 KT
60
Speedometer display
6
1. OPERATIONAL OVERVIEW
7
1. OPERATIONAL OVERVIEW
5. Press ▲ to display “-“. 6. Press the [ENT] key, use the cursor pad
6. Press ► to send the cursor to the next to enter speed to use for the simulation,
digit. and then press the [ENT] key.
7. Press ▲ or ▼ to display “0.” 7. Press the [ENT] key.
8. Press ► to send the cursor to the next 8. Choose course (AUTO or MAN) and then
digit. press the [ENT] key. For manual entry of
9. Press ▲ or ▼ to display “6.” course, press the [ENT] key, enter course
10. Press ► to send the cursor to the next with the cursor pad, and then press the
digit. [ENT] key. The AUTO course tracks a
11. Press ▲ or ▼ to display “3.” circular course.
12. Press ► to send the cursor to the last Note: Course must be AUTO to set
digit. simulation destination.
13. Press ▲ or ▼ to display “0.”
9. Press the [ENT] key, enter latitude with
14. Press the [ENT] key.
the cursor pad, and then press the [ENT]
15. Press the [MENU] key twice to finish.
key.
10. Press the [ENT] key, enter longitude, and
then press the [ENT] key.
1.6 Simulation Display 11. Press the [MENU] key twice.
The simulation display provides simulated 12. Choose the PLOTTER display with the
operation of this unit. You may set the speed [DISP] key. SIM appears at the upper
manually and course manually or left-hand corner when the simulator
automatically. All controls are operative - you display is active.
may enter marks, set destination, etc.
Simulation mode active
8
2. PLOTTER DISPLAY OVERVIEW
2.1 Choosing the Display 3. Use ▲ (increase) or ▼ (decrease) to
Range choose range desired.
4. Press the [ENT] key to close the zoom,
You may choose the display range on the ship centering window.
plotter and highway displays. The horizontal
range in the plotter display is available among
0.02 (40 yd), 0.05 (101 yd), 0.1 (202 yd), 0.2 2.2 Shifting the Cursor
(405 yd), 0.5, 1, 2, 5, 10, 20, 40, 80, 160 and
320 nautical miles. (Nautical mile is the Use the cursor pad to shift the cursor. The
default unit of display range. Display range cursor moves in the direction of the arrow or
may also be shown in kilometers or miles. diagonal pressed on the cursor pad.
Ranges shorter than the 0.5 nm are also
shown in yards or meters on the plotter Cursor state and data
display.) The horizontal range in the highway Cursor state determines what data is shown
display is available among 0.2, 0.4, 0.8, 1, 2, on the display.
4, 8 and 16 nautical miles.
Cursor turned on
1. Press the [MENU] key. The zoom, ship
Cursor position is displayed in latitude and
centering window appears.
longitude or TDs (depending on menu
setting) at the bottom of the plotter display
ZOOM IN/OUT?
when the cursor is on. The range and bearing
SHIP TO CENTER?
from own ship to the cursor appear at the
Quit?
left-hand side of the display.
PRESS [MENU] TO SEE Bearing from own Own ship Cursor
THE MAIN MENU. ship to cursor
D2D
Zoom, ship centering window n
[ .02 m ]
Note: “SHIP TO CENTER?” does not 40 y
d
appear when the highway display mode is BRG: +
active. 131°
RNG: +
2. ZOOM IN/OUT is selected. Press the 0.03 mn
[ENT] key to show the zoom window.
+ 34°44.000N 135°21.000E
ZOOM
EXIT:
[ENT]
Zoom window
9
2. PLOTTER DISPLAY OVERVIEW
10
2. PLOTTER DISPLAY OVERVIEW
ERASE
WAYPOINTS/MARKS?
ROUTES?
TRACK?
RESET TRIP? (6.40nm)
RESET ODO? (6.40nm)
GPS DATA?
MENU SETTINGS?
ALL BACKUP DATA?
ERASE menu
3. Choose “TRACK?” and then press the
[ENT] key. The message shown below
appears.
ERASE TRACK.
11
2. PLOTTER DISPLAY OVERVIEW
12
3. WAYPOINTS (MARKS)
3.1 Entering Waypoints c) Press ► to move the cursor one place
and then press ▲ or ▼ to display B.
In navigation terminology a waypoint is a
d) Press ► to move the cursor one place
particular location on a voyage, whether it be
and then press ▲ or ▼ to display E.
a starting, intermediate or destination
e) Press the [ENT] key. The following
waypoint. Your unit can store 999 waypoints.
window appears.
Waypoints can be entered on the plotter
display three ways: at cursor position, at own
Comment (default: date/time)
ship’s position, and from the waypoint list.
Mark shape
Entering a waypoint with the cursor
NAME: KOBE
1. Use the cursor pad to place the cursor on 34°39.836'N MARK
the location desired for a waypoint. 135°12.059'E x
2. Press the [ENT] key. The following 10-JAN-02 10:25
window appears. TTG 02H00M ETA: 12:25
Exit? LOG RTE?
CURSOR POS. → WPT
TTG and ETA calculated according
ENTER A NEW WPT NAME. to speed set at TTG/ETA SPEED on
0 0 1_ _ _? PLOTTER menu.
13
3. WAYPOINTS (MARKS)
d) Press the [ENT] key. The cursor is 5. To change mark shape, place the cursor
selecting date/time, the default under “MARK.” Press the [ENT] key, use
comment. Press the [ENT] key. ▲ or ▼ to choose mark desired, and then
e) Enter a comment (max. 16 press the [ENT] key again.
alphanumeric characters) with the 6. The cursor is selecting date/time. To
cursor pad and then press the [ENT] change the date/time to your own
key. To create a space, choose the comment, press the [ENT] key, enter a
“blank” character. To remove all comment with the cursor pad, and then
characters which follow the cursor, press the [ENT] key again.
choose the underline.
7. Place the cursor on “Exit?.” Press the
f) The cursor is on “Exit?.” Press the [ENT] key to finish.
[ENT] key to finish.
Entering a waypoint from the waypoint
Entering a waypoint at own ship list
position
1. Press the [MENU] key once or twice to
1. Press the [MARK/MOB] key momentarily
display the menu.
on any display. The following window
2. Choose WAYPOINTS.
appears.
3. Press the [ENT] key to show the waypoint
GPS POS. MARK list options. Choose LIST. (NEAREST
displays waypoints from nearest to
furthest; however, waypoints cannot be
entered from this display.)
LIST
NEAREST
14
3. WAYPOINTS (MARKS)
5. The cursor is selecting “NEW?”; press the 3.2 Entering the MOB Mark
[ENT] key.
The MOB mark denotes man overboard
ENTER A NEW WPT NAME. position. Only one MOB mark may be entered.
Each time the MOB mark is entered the
0 0 4_ _ _? previous MOB mark and its position data are
written over.
(004:DEFAULT NAME)
Quit: [MENU]
1. Press the [MARK/MOB] key on any
display until the following display appears.
Waypoint name entry window
6. Enter name (if desired) with the cursor SAVED TO MOB.
pad and then press the [ENT] key. GO TO MOB ?
MOB window
2. To set MOB position as destination, press
◄ to choose YES and then press the
[ENT] key. Then, the plotter display marks
* Current position MOB position as shown in the illustration
Waypoint attribute edit window below.
7. The cursor is selecting latitude. Press the Note: Selecting “NO” saves the position
[ENT] key. Enter latitude with the cursor as a waypoint.
pad and then press the [ENT] key.
MOB position set
8. Press the [ENT] key, enter longitude in as destination
similar fashion as you did with latitude and
D2D
then press the [ENT] key.
n
[ 40 m ]
Note: To enter position by TDs, see
paragraph 7.8. BRG: MOB
9. To change mark shape, choose the mark
RNG:
currently shown and then press the [ENT]
0.06 mn
key. Use ▲ or ▼ to choose mark desired
and then press the [ENT] key.
10. To change date and time to the comment Bearing and range to MOB position
of your choice, press the [ENT] key, enter
comment with the cursor pad, and then Plotter display when MOB
press the [ENT] key again. is set as destination
11. Place the cursor on “Exit?.” Press the
[ENT] key.
12. Press the [MENU] key twice to finish.
15
3. WAYPOINTS (MARKS)
CREATE?*
RENAME?
*: Not shown when NEAREST is
Quit?
selected at step 3.
16
3. WAYPOINTS (MARKS)
ERASE WPTS/MARKS
WPTS/MARKS list (NEAREST) by distance
[ALL?] CURSOR KOBE
4. To display ETA and TTG for each MOB START 001
002 003 004
waypoint, press ►. 005 006 007
______ ______ ______
______ ______ ______
WPTS/MARKS (NEAREST) ______ ______ ______
KOBE : 1H00M 12:00
002 : 2H00M 13:00
003 : 2H30M 13:30 ERASE WPTS/MARKS display
004 : 4H00M 15:00 4. Choose the waypoint you want to erase.
005 : 5H30M 16:30
006 : 6H00M 17:00 Note: You cannot erase CURSOR, MOB
007 : 7H00M 18:00
or START. To erase all waypoints, choose
ALL.
WPTS/MARKS (NEAREST) list by TTG to ETA
5. Press the [ENT] key. A screen showing
5. To return to the waypoint list by distance, position and other particulars of the
press ◄. waypoint selected appears.
6. Press the [MENU] key twice to close the
menu.
NAME: KOBE
34°39.836'N MARK
135°12.059'E x
10-JAN-02 10:25D
TTG 02H00M ETA: 12:25
Quit? ERASE?
Waypoint data
6. Press ► to choose “ERASE?” and then
press the [ENT] key.
7. Press the [MENU] key twice to finish.
17
3. WAYPOINTS (MARKS)
18
4. ROUTES
In many cases a trip from one place to Creating a route with the cursor
another involves several course changes,
This is probably the easiest method by which
requiring a series of waypoints which you
to create a route.
navigate to, one after another. The sequence
of waypoints leading to the ultimate
1. Use the cursor pad to place the cursor on
destination is called a route. Your unit can
position desired. (Cursor position is
automatically advance to the next waypoint
shown at the bottom of the screen.)
on a route, so you do not have to change the
2. Press the [ENT] key. The following
destination waypoint repeatedly.
window appears.
19
4. ROUTES
ROUTES menu
Screen for entering route by waypoint
8. “LOG” shows the first and last waypoints
entered for the log route you are currently 5. Choose location (01, etc.) and then press
creating. Choose LOG and then press the the [ENT] key. Use ▲ or ▼ to display
[ENT] key. waypoint name. (In the example, KOBE.)
6. Press the [ENT] key.
EDIT? 7. Repeat steps 5 and 6 until you have
MOVE? entered all waypoints desired.
Note: If you enter a waypoint which has
Route processing options not been registered, your screen will show
9. “MOVE?” is selected; press the [ENT] key. a message which looks something like the
The route is moved from “LOG” and is one below. Press ◄ to choose YES and
registered under the next sequential route then press the [ENT] key to create a new
number. (To edit the route before saving it, waypoint; choose NO to return to the
choose ”EDIT?”. For how to edit a route, route entry screen.
see paragraph 4.2.) NEW WPT NAME.
CREATE 008?
Creating a route from the route menu
ARE YOU SURE?
The procedure which follows describes how YES NO
to create a route from two preregistered
waypoints, KOBE and OSAKA. New waypoint creation screen
When you choose YES, the following
1. Press the [MENU] key once or twice to screen appears. Edit the waypoint as
display the menu. necessary, choose “Exit?” and then press
2. Choose ROUTES. the [ENT] key.
3. Press the [ENT] key.
20
4. ROUTES
ROUTES list
ROUTES list
11. Press the [MENU] key twice to finish.
9. Choose LOG and then press the [ENT]
Creating a route from the waypoint list key.
WPTS/MARKS (list)
21
4. ROUTES
Creating a track-based route 5. Choose LOG and then press the [ENT]
key.
There are two methods by which you can
create a track-based route: manual input of EDIT?
track points using the [MARK/MOB] key and MOVE?
automatic input of track points from the
ROUTES menu. A track-based route is useful Route processing options
for retracing your track. 6. “MOVE?” is selected; press the [ENT] key.
The route is moved from “LOG” and is
Creating a track-based route manually
registered under the next sequential route
This method creates a route by storing number.
position each time the [MARK/MOB] key is 7. Press the [MENU] key twice to finish.
pressed.
Creating a track-based route automatically
1. Press the [MARK/MOB] key momentarily.
This method creates a route by automatically
storing position at intervals of time or
NAME: 001
34°39.836'N MARK distance.
135°12.059'E x
10-JAN-02 10:25D 1. Press the [MENU] key once or twice to
TTG 02H00M ETA: 12:30 open the menu.
Exit? LOG RTE? 2. Choose ROUTES and then press the
[ENT] key.
Waypoint attribute edit window 3. Choose INTERVAL and then press the
2. Change name, comment and mark shape [ENT] key.
if desired. Choose “LOG RTE?” and then
press the [ENT] key. TIME
3. Repeat steps 1 and 2 when you change DISTANCE
course.
4. Choose TIME or DISTANCE (the method
4. When you have entered all the waypoint
by which position will be stored) as
positions desired, press the [MENU] key
appropriate and press the [ENT] key.
twice, choose ROUTES and then press
5. Press the [ENT] key. Use the cursor pad
the [ENT] key.
to set time or distance value and then
ROUTES press the [ENT] key.
VOYAGE ROUTE: STOP 6. Choose VOYAGE ROUTE and then press
INTERVAL: TIME 00H10M the [ENT] key.
NO [NEW?]
LOG 001→ 003
01 KOBE → OSAKA START
__ ________________ STOP
__ ________________
22
4. ROUTES
8. Press the [MENU] key twice to finish. 5. Place the cursor on the waypoint to
The current position is saved under the replace.
next sequential waypoint number, the 6. Press the [ENT] key to show the route edit
display shows “***SAVED!” (*** = options.
waypoint number) and a beep sounds.
Thereafter waypoints are saved at the CHANGE?
interval of time or distance set. REMOVE?
INSERT?
When 30 waypoints have been saved, a SKIP?
message informs you that you can no Quit?
longer save waypoints to the route. Press
the [ENT] key to erase the message. The
route is automatically saved to “LOG” in Route edit options
the ROUTES menu, under the name of 7. “CHANGE?” is selected; press the [ENT]
the first and last waypoint numbers used. key.
Then, open the ROUTES menu and go to
step 13. NAME: 001
34°39.836'N MARK
You can manually stop saving waypoints 135°12.059'E x
and save the route by going to step 9. 10-JAN-02 10:25D
9. After the desired number of waypoints TTG 02H00M ETA: 12:25
have been entered, press the [MENU] key Exit?
once or twice to open the menu.
10. Choose ROUTES and then press the Waypoint attribute edit screen
[ENT] key. 8. NAME is selected. Press the [ENT] key.
11. Choose VOYAGE ROUTE and then press Use the cursor pad to enter waypoint
the [ENT] key. name.
12. Choose STOP and then press the [ENT] 9. Press the [ENT] key.
key.
Note: If the name entered at step 8 does
13. Choose LOG and then press the [ENT]
not exist, the window shown below
key.
appears. Choose “CREATE?”,
14.“MOVE?” is selected; press the [ENT] key.
“RENAME?” or “Quit?” as appropriate and
The route is moved from “LOG” and is
then press the [ENT] key.
registered under the next sequential route
number.
15. Press the [MENU] key twice to finish. CREATE?
RENAME?
Quit?
4.2 Editing Routes
Waypoint name options
Replacing waypoints in a route
10. Choose “Exit?.”
1. Press the [MENU] key once or twice to 11. Press the [ENT] key.
display the menu. 12. Press the [MENU] key twice to finish.
2. Choose ROUTES and then press the
[ENT] key.
3. Choose the route to edit.
4. Press the [ENT] key.
23
4. ROUTES
24
4. ROUTES
25
4. ROUTES
26
5. DESTINATION
Destination can be set four ways: by cursor, A dashed line connects own ship and the
by waypoint, by route, and by MOB position. destination, which is marked with “CURSOR”
Previous destination is cancelled whenever a and an “X,” as shown in the illustration below.
destination is newly set. CURSOR
x
27
5. DESTINATION
FORWARD?
REVERSE? SELECT USER WPT list
3. Choose waypoint desired and then press
Route following direction options the [ENT] key. The GOTO window
6. Choose “FORWARD?” or “REVERSE?”, appears, showing the waypoint selected
the order in which to traverse the route as below.
waypoints, and then press the [ENT] key. GOTO
[ROUTE 01] Intermediate Point 2 OSAKA WPT-LIST? 001 Location of
(WPT 002) (Arrival point) WPT-NEAR? OFF?? user waypoint
Intermediate Point 1 (Example: 001)
(WPT 001)
ROUTE?
CURSOR? SETUP?
FORWARD REVERSE
KOBE GOTO options
(Starting point) Intermediate Point 1
(WPT 003) 4. Choose user waypoint and then press the
Meaning of forward and reverse [ENT] key.
Current position becomes the starting point. A
dashed line runs between the starting point A dashed line connects own ship and the
and all route waypoints. Next destination waypoint selected, which is shown in reverse
waypoint is shown in reverse video. video.
28
6. ALARMS
There are eight alarm conditions which 6.1 Arrival Alarm, Anchor
generate both audio and visual alarms: Watch Alarm
Arrival alarm, Anchor watch alarm, XTE
(Cross-Track Error) alarm, Speed alarm, You may activate the arrival alarm or the
WAAS/DGPS alarm, Time alarm, Trip alarm anchor watch alarm; they cannot be activated
and Odometer alarm. together.
ALARMS
2D XTE ALARM! ! BUZZER : LONG
ARV/ANC : ARV 0.30 nm
[ 40 n ]
m XTE : OFF 0.50 nm
SPEED : OFF 12.0 kt
COG: Alarm WAAS/DGPS : OFF
82° icon TIME : OFF 00:00
TRIP : OFF 0 nm
SOG:
k ODOMETER : OFF 0 nm
9.0 t
29
6. ALARMS
4. Choose ARV/ANC and then press the 6. Press the [ENT] key. Enter the alarm
[ENT] key. range (0.01-99.99 nm) with the cursor
pad.
OFF 7. Press the [ENT] key.
ARV 8. Press the [MENU] key twice to finish.
ANC
When own ship drifts more than the range set
Arrival/anchor watch options here, the buzzer sounds and the message
5. Choose ARV and then press the [ENT] ANC ALARM! and the alarm icon appear.
key.
6. Press the [ENT] key. Enter the alarm
range (0.0-99.99 nm) with the cursor pad. 6.2 XTE (Cross Track Error)
7. Press the [ENT] key. Alarm
8. Press the [MENU] key twice to finish.
The XTE alarm warns you when own ship is
off its intended course.
When own ship nears the GOTO waypoint by
the range set here, the buzzer sounds and
the message ARV ALARM! appears.
Alarm Destination
Anchor watch alarm Own ship's
setting waypoint
position
The anchor watch alarm sounds to warn you
that own ship is moving when it should be at
rest.
: Alarm released
Own ship's
Alarm position How the XTE alarm works
setting 1. Press the [MENU] key once or twice to
open the menu.
2. Choose ALARMS.
3. Press the [ENT] key.
4. Choose XTE and then press the [ENT]
Destination
waypoint : Alarm released key.
5. Choose ON and then press the [ENT] key.
How the anchor watch alarm works 6. Press the [ENT] key. Enter alarm range
Before setting the anchor watch alarm, set (0.0-99.99 nm) with the cursor pad.
current position as destination waypoint, 7. Press the [ENT] key.
referring to paragraph 5.2. 8. Press the [MENU] key twice to finish.
1. Press the [MENU] key once or twice to When own ship strays from the intended track
open the menu. by the range set here, the buzzer sounds and
2. Choose ALARMS. message XTE ALARM! and the alarm icon
3. Press the [ENT] key. appear.
4. Choose ARV/ANC and then press the
[ENT] key.
5. Choose ANC and then press the [ENT]
key.
30
6. ALARMS
31
6. ALARMS
1. Press the [MENU] key once or twice to 1. Press the [MENU] key once or twice to
open the menu. open the menu.
2. Choose ALARMS. 2. Choose ALARMS.
3. Press the [ENT] key. 3. Press the [ENT] key.
4. Choose TRIP and then press the [ENT] 4. Choose BUZZER and then press the
key. [ENT] key.
5. Choose ON and then press the [ENT] key.
6. Press the [ENT] key. Enter distance SHORT
desired (001-999 nm) with the cursor pad. LONG
7. Press the [ENT] key. CONSTANT
8. Press the [MENU] key twice to finish.
Buzzer sound options
When the boat has traveled further than the 5. Choose buzzer type desired and then
preset trip distance, the buzzer sounds and press the [ENT] key.
the message TRIP ALARM! and the alarm SHORT: Two short beeps
icon appear. LONG: Three long beeps
CONSTANT: Continuous beeps
6. Press the [MENU] key twice to finish.
6.7 Odometer Alarm
This alarm alerts you by aural and visual
alarms when your boat has traveled the total
distance you set.
32
7. OTHER FUNCTIONS
7.1 Calculating Range, 10. Press the [ENT] key. Enter speed with the
Bearing, TTG and ETA cursor pad and then press the [ENT] key.
Range and bearing between two The illustration below shows what the
waypoints display might look like using waypoints
1. Press the [MENU] key once or twice to KOBE and OSAKA as the FROM and TO
open the menu. waypoints, respectively.
2. Choose CALCULATE and then press the Time-to-Go
[ENT] key. Estimated Time of Arrival
CALCULATION CALCULATION
CALCULATION menu
Range Bearing
3. The cursor is selecting MODE. Press the Typical range and bearing calculation
[ENT] key. between two waypoints
11. Press the [MENU] key twice to finish.
WAYPOINTS
ROUTE
Range, TTG and ETA between first and
Range and bearing calculation options final waypoints of a route
4. Choose WAYPOINTS and then press the You can easily find the range, TTG and ETA
[ENT] key. between the first and final waypoints of a
5. Press the [ENT] key. route as follows:
6. Enter the FROM waypoint and then press
the [ENT] key. 1. Press the [MENU] key once or twice to
7. Press the [ENT] key, enter the TO open the menu.
waypoint and then press the [ENT] key. 2. Choose CALCULATE and then press the
8. Press the [ENT] key to display the speed [ENT] key.
input options. 3. Press the [ENT] key.
4. Choose ROUTE and then press the [ENT]
AUTO key.
MAN 5. Press the [ENT] key.
6. Choose route number from the route list
Speed input options with the cursor pad.
9. Choose AUTO or MAN and then press the 7. Press the [ENT] key to open the speed
[ENT] key. AUTO uses ship’s average input options window.
speed; MAN is for manual entry of speed. 8. Choose AUTO or MAN. AUTO uses ship’s
For AUTO, see the illustration after step average speed; MAN is for manual entry
10 for sample range and bearing of speed.
calculation. For MAN, go to step 10.
33
7. OTHER FUNCTIONS
9. Press the [ENT] key. If you selected 4. Choose appropriate mode referring to the
AUTO no further operation is necessary. descriptions below. Press the [ENT] key.
See the illustration below for a calculation WAAS: Position fix by WAAS
example. For MAN, press the [ENT] key, AUTO: Position fix in priority order of
enter speed with the cursor pad and then DGPS, WAAS, and GPS.
press the [ENT] key. 5. Press the [ENT] key.
The illustration below shows what the 6. WAAS SEARCH is selected; press the
display might look like using Route-01 as [ENT] key.
an example.
Time-to-Go AUTO
Estimated Time of Arrival MANUAL
CALCULATION
WAAS search options
MODE : ROUTE
NO. : 01 (WPTS: 4) 7. Choose AUTO for automatic search or
KOBE → OSAKA
SPD : AUTO
MANUAL for manual search and then
press the [ENT] key. The table below
TTG: 1H55M
RNG: 11.25 nm
ETA: 07:17
BRG: _ _ _ °
shows the available GEO satellites.
34
7. OTHER FUNCTIONS
8. For GP-37, press the [ENT] key with EXT BEACON: Position fix by external
“CORRECTIONS DATA SET” selected. DGPS beacon receiver (GP-32)
Enter the WAAS correction message AUTO: Position fix by DGPS, WAAS and
number then press the [ENT] key. Use the GPS, in order of availability.
setting “02” or “00”. Note: When connecting FURUNO
Note: For GP-32, the default setting is 00. external DGPS beacon receiver GR-80 to
Adjustment is not required. the GP-32, turn the GR-80’s remote
9. Press the [MENU] key twice to close the function on to set up the beacon receiver
menu. with data set on the GP-32.
5. DGPS STATION is selected; press the
[ENT] key.
7.3 DGPS setup 6. Choose DGPS beacon station selection
method: AUTO, MANUAL or LIST.
1. Press the [MENU] key once or twice to
AUTO: Automatically searches for best of
open the menu.
five nearest DGPS beacon station. It first
2. Choose WAAS/DGPS.
searches DGPS beacon stations from
WAAS/DGPS SETUP closest to furthest. If unsuccessful it
MODE : GPS searches stations by signal strength. This
WAAS SEARCH: AUTO 120 procedure is repeated until a suitable
CORRECTIONS DATA SET: 02
DGPS STATION: AUTO station is found.
RATE : 200BPS
FREQ : 310.0 kHz
MANUAL: Manually enter DGPS beacon
STATION : ---* DATA: ---* station specifications at RATE and FREQ,
SIG.S: 00.0 dB * SNR: 02.0dB*
referring to a DGPS beacon station list.
* = See note below.
LIST: Lists five of the closest DGPS
WAAS/DGPS SETUP menu beacon stations, including
user-programmed stations.
DGPS Data
7. Press the [ENT] key. If you selected
STATION: Shows GOOD or NG. AUTO no further operation is required; go
to step 8. If you selected MANUAL or LIST,
DATA: Shows GOOD or NG.
do one of the following and then go to
SIG. S: Signal Strength. A figure step 8.
between 0 and 99 is shown. The higher
the figure the stronger the beacon signal. MANUAL
SNR: Signal to Noise Ratio. A figure a) The cursor is selecting RATE. Press
between 1and 22 is shown. A figure under
18 means position will be inaccurate. the [ENT] key.
When your boat is in the service area of a b) Choose the transmission rate of the
beacon station, SNR should be 21 or 22.
DGPS beacon station to be used,
If not, the problem may lie with the
grounding, radar interference or generator among 50, 100 or 200 bps. Press the
noise on own boat. [ENT] key.
c) The cursor is selecting FREQ. Press
3. Press the [ENT] key to show the mode the [ENT] key.
options window.
d) Use the cursor pad to enter the
4. Choose one of the following and then
transmission frequency of the DGPS
press the [ENT] key.
beacon station to be used and then
INT BEACON: Position fix by internal press the [ENT] key.
DGPS beacon receiver (GP-37 only,
cannot be selected on GP-32)
35
7. OTHER FUNCTIONS
36
7. OTHER FUNCTIONS
6. Choose a station from the list and then Erasing individual user channels
press the [ENT] key. The display looks
1. Press the [MENU] key twice to open the
something like the one below.
menu.
2. Choose DGPS/WAAS and then press the
FREQ : 310.0kHz
RATE : 200BPS [ENT] key.
LAT : 37°59'N 3. Choose DGPS STATION and then press
LON : 123°00'W
the [ENT] key.
EXIT? SAVE? ERASE? 4. Choose LIST and then press the [ENT]
key.
5. Choose USER and then press the [ENT]
key.
Screen for entering DGPS station data 6. Choose a channel from the list and then
7. Choose item, press the [ENT] key, edit press the [ENT] key.
data, and then press the [ENT] key. 7. Choose “ERASE?”.
8. Choose “SAVE?” and then press the 8. Choose YES and then press the [ENT]
[ENT] key. key.
9. Press the [MENU] key twice to finish. 9. Press the [MENU] key twice to finish.
37
7. OTHER FUNCTIONS
38
7. OTHER FUNCTIONS
39
7. OTHER FUNCTIONS
The GPS SETUP menu smoothes position During position fixing, ship’s velocity (speed
and course, averages speed, applies position and course) is directly measured by receiving
offset, and deactivates unhealthy satellites. GPS satellite signals. The raw velocity data
may changes randomly depending on
1. Press the [MENU] key once or twice to receiving conditions and other factors. You
open the menu. can reduce this random variation by
2. Choose GPS SETUP and then press the increasing the smoothing. Like with latitude
[ENT] key. and longitude smoothing, the higher the
speed and course smoothing the more
GPS SETUP smoothed the raw data. If the setting is too
SMOOTH POS : 0SEC high, however, the response to speed and
SMOOTH S/C : 5SEC course change slows. The setting range is
AVR. SPEED : 60SEC
LAT OFFSET : 0.000'N
from 0 (no smoothing) to 9999 seconds.
LON OFFSET : 0.000'E
DISABLE SV : __ __ __ AVR. SPEED (Speed averaging)
FIX MODE : 2/3D
Calculation of ETA and TTG, etc. is based on
average ship's speed over a given period. If
GPS SETUP menu
the period is too long or too short, calculation
3. Choose item and then press the [ENT]
error will result. Change this setting if
key.
calculation error occurs. The default setting is
4. Change setting with the cursor pad and
60 seconds. The setting range is from 0 (no
then press the [ENT] key.
averaging) to 9999 seconds.
5. Press the [MENU] key twice to finish.
LAT/LON OFFSET (L/L position offset)
GPS SETUP menu description
You may apply an offset to latitude and
SMOOTH POS (Smoothing position)
longitude position generated by the GPS
When the DOP (Dilution of Precision, the receiver, to increase position accuracy.
index for position-fixing accuracy) or receiving
condition is unfavorable, the GPS fix may DISABLE SV
change greatly, even if the vessel is dead in
Every GPS satellite is broadcasting abnormal
water. This change can be reduced by
satellite number(s) in its Almanac, which
smoothing the raw GPS fixes. The setting
contains general orbital data about all GPS
range is from 0 (no smoothing) to 999
satellites. Using this information, the GPS
seconds. The higher the setting the more
receiver automatically eliminates any
smoothed the raw data, however too high a
malfunctioning satellite from the GPS satellite
setting slows response time to change in
schedule. However, the Almanac sometimes
latitude and longitude. This is especially
may not contain this information. You can
noticeable at high ship’s speeds. “0” is the
disable an inoperative satellite manually.
normal setting; increase the setting if the
Enter satellite number in two digits and then
GPS fix changes greatly.
press the [ENT] key. To restore a satellite
enter “00”.
40
7. OTHER FUNCTIONS
USER DISPLAY
USER DISPLAY menu,
default digital display settings
1: DIGITAL 7. “A” is selected. Press the [ENT] key.
2: SPEEDOMETER
NONE ODO TRIP
TIME POSN POWER
SOG COG WPT
XTE TTG ETA
41
7. OTHER FUNCTIONS
8. Use the cursor pad to choose data 9. Enter scale interval: Use ◄ or ► to
desired and then press the [ENT] key. choose location and ▲ or ▼ to enter
NONE: No display value. The setting range is 1 to 99.
ODO: Odometer distance 10. Press the [ENT] key.
TRIP: Trip distance
11. Press the [MENU] key twice to close the
TIME: Time and date
POSN: Position menu.
POWER: Power source voltage
SOG: Speed over ground
COG: Course over ground 7.12 Resetting Trip and
WPT: Rng and brg to waypoint
XTE: Cross-track error Odometer Distances
TTG: Time to go (to destination) 1. Press the [MENU] key once or twice to
ETA: Estimated time of arrival open the menu.
(at destination)
2. Choose ERASE and then press the [ENT]
9. Control returns to the User display setup,
key.
with “B” selected. Depending on the
3. Choose “RESET TRIP?” (or “RESET
selection made at step 5, set other
ODO?”) and then press the [ENT] key.
indications similar to how you did with “A”.
One of following displays appears.
10. Press the [MENU] key twice to finish.
Speedometer menu
5. The cursor is selecting START FROM.
Press the [ENT] key.
6. Enter starting speed: Use ◄ or ► to
select location and ▲ or ▼ to enter value
and switch from plus to minus and vice
versa. The setting range is -99 to +99.
7. Press the [ENT] key, and the cursor shifts
to INTERVAL.
8. Press the [ENT] key.
42
7. OTHER FUNCTIONS
WIRING INFO
Downloading data to a PC
1TD-H WHITE PC/AT DSUB-9
2TD-C/SG BLUE 5 GND 1. Press the [MENU] key once or twice to
3SD YELLOW 2 RXD
4RD 3 TXD open the menu, choose I/O SETUP and
GREEN
5 + RED 4 DTR then press the [ENT] key.
6 - BLACK 6 DSR
7FG - + 7 RTS
8 CTS I/O SETUP
GP-32/37 12/24VDC DATA1 : NMEA-REM1
DATA2 : NMEA-REM
NMEA VER : VER2.0
Wiring diagram, using SAVE WPT/RTE → PC?
DSUB 9-pin connector LOAD WPT/RTE ← PC?
LOAD WPT← YEOMAN?
Note: A DSUB 25-pin (EIA-232) may also be WIRING INFO?
1 TD-H
2. Choose SAVE WPT/RTE → PC?.
WHITE
2 TD-C/SG BLUE 7 GND 3. Press the [ENT] key.
3 SD YELLOW 3 RXD
4 RD GREEN 2 TXD
SAVE WPT/RTE
5 + RED 4 RTS
6 - BLACK 5 CTS ALL WPTS/ROUTES
7 FG - + 6 DSR WILL BE SAVED TO PC.
20 DTR
SET PC PORT TO 4800
8 BIT, P-N, S1, XON/OFF.
Wiring diagram, using
CONTINUE?
DSUB 25-pin connector
43
7. OTHER FUNCTIONS
LOADING START?
SAVING START? (PC READY?)
(PC READY?)
ARE YOU SURE?
ARE YOU SURE? YES NO
YES NO
Downloading sequence
7. Press any key to escape. Message when data is loaded successfully
8. Press any key to escape.
Uploading data from a PC
Note that all waypoint and route data stored Loading data from a YEOMAN
in the GP-37/GP-32 will be deleted when data Waypoint data from a YEOMAN has the
is uploaded. same format as does the NMEA 0183 data
sentence WPL.
1. Press the [MENU] key once or twice to
open the menu, choose I/O SETUP and 1. Press the [MENU] key twice, choose I/O
then press the [ENT] key. SETUP and then press the [ENT] key.
2. Choose LOAD WPT/RTE ← PC?. 2. Choose LOAD WPT ← YEOMAN?.
3. Press the [ENT] key. 3. Press the [ENT] key.
CONTINUE? CONTINUE?
44
7. OTHER FUNCTIONS
4. Press the [ENT] key. 7: Waypoint comment (2 byte for mark code
+ 16 characters of comment.)
LOADING START? 1st byte of mark code: Fixed to '@'.
(YEOMAN READY?)
2nd byte of mark code: Internal mark
ARE YOU SURE? code + 'a' (0 x 61). See Note 1 on the
YES NO next page.
Number of characters for comment is
LOADING START? prompt less than 16 (variable length). See Note 2
on the next page.
5. Set up the YEOMAN to output data.
8: Flag making waypoint. Always set to “A”.
6. Press ◄ to choose YES and then press
“A”: Displayed
the [ENT] key to load data.
”V”: Not displayed
Now loading
WAYPOINTS
data 9: UTC (Always NULL)
LOADING....
10: Day (Always NULL)
END? To quit loading, 11: Month (Always NULL)
press the [ENT] key.
12: Year (Always NULL)
Message when waypoints are being loaded Note 1: Internal mark code is 0 x 10 through
7. Data is loaded to empty location and the 0 x 18. 0 x 71 through 0 x 79 are always
buzzer sounds twice to signify successful placed at 2nd byte of mark code.
loading. If there is not enough memory Note 2: Following characters can be used for
free to store the waypoints, the message comments:
below appears.
_ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789&()+-/=?}
WAYPOINTS FULL 0x10: (q) 0x11: (r) 0x12: (s) 0x13: (t) 0x14: (u)
FULLNOT LOADING
0x15: (v) 0x16: (w) 0x17: (x) 0x18: (y)
HIT ANY KEY.
45
7. OTHER FUNCTIONS
End of sentence
46
8. MAINTENANCE &
TROUBLESHOOTING
8.1 Maintenance 8.2 Displaying the Message
Regular maintenance is important to maintain Board
performance. Check the following points The message board displays error messages
monthly to help maintain performance. and alerts. You can display it as follows:
47
8. MAINTENANCE & TROUBLESHOOTING
48
8. MAINTENANCE & TROUBLESHOOTING
D3D DOP 01
Battery exchange Elevation 1. 5 02
N --
confirmation window 45° 07
06 04
05
5. Press any key to automatically turn off the 02
08 06
unit. 04 07
08
10
6. Replace the battery. 12
05
--
10
--
01 W
12
Note 1: When it is expected that the 85m 122
equipment will not be used for a long time,
GEO GEO satellite
execute the above procedure before turning satellite
the power off, to prevent loss of data. Satellite number in reverse
Altitude video is used for positioning.
Note 2: Data is copied from the flash memory Elevation 5°
to the RAM at the next power up.
Satellite monitor display
4. Press the [MENU] key twice to quit the
SATELLITE display.
8.5 Satellite Monitor Display
The satellite monitor display shows
information about GPS and GEO satellites. 8.6 Diagnostics
The diagnostic test checks the ROM, RAM,
1. Press the [MENU] key once or twice to
input data, beacon receiver board*2, GPS
open the menu.
core*1, internal battery, RTC*2, keyboard, and
2. Choose SATELLITE.
LCD performance. (*1: GP-32, *2: GP-37)
3. Press the [ENT] key.
Number, bearing and elevation angle of
1. Press the [MENU] key once or twice to
all GPS and GEO satellites (if applicable)
open the menu.
in view of your receiver appear. Satellites
2. Choose SYS SETUP and then press the
being used in fixing position are displayed
[ENT] key.
in reverse video; satellites not being used
3. Choose “TEST?” and then press the
are shown in normal video.
[ENT] key. You are asked if you are ready
to start the test.
TEST START ?
(STOP: PWR OFF)
49
8. MAINTENANCE & TROUBLESHOOTING
LCD check
50
8. MAINTENANCE & TROUBLESHOOTING
Note 2: When the memory is cleared the default position is restored as below.
51
8. MAINTENANCE & TROUBLESHOOTING
52
9. INSTALLATION
9.1 Installation of Display Unit Flush mounting
Desktop Overhead
53
9. INSTALLATION
Spring
9.2 Installation of Antenna Washer
Gasket (reddish-brown)
Unit Shield
Nut
Mounting considerations Pin
Connector
Install the antenna unit referring to the
antenna installation diagram at the end of this
manual. When choosing a mounting location
How to assemble the connector
for the antenna unit, keep in mind the
following points:
54
9. INSTALLATION
The illustration below shows where to The display unit contains a CPU. While it is
connect cables on the rear of the display unit. operating, it radiates noise, which can
Please review the INSTALLATION interfere with radio equipment. Ground the
GUIDELINES at the front of this manual unit as follows to prevent interference:
before wiring the equipment. • The ground wire for the display unit should
ANTENNA UNIT ANTENNA UNIT be 1.25sq or larger and as short as
GPA-017 GPA-019 possible.
(For GP-32) (For GP-37)
• The signal ground and frame ground are
separated, however the power line is not
OR isolated. Therefore, do not connect the
signal ground to the frame ground when
DISPLAY UNIT connecting other equipment to a positive
With 10 m GP-32 OR GP-37 ground battery.
cable
External equipment
MJ-A7SPF0009-020C,
2m The power supply port is commonly used for
connection of external equipment such as a
Ground radar. Refer to the interconnection diagram
on page S-1 or S-2 for connection of external
Black -
*+ Red equipment.
POWER
(12-24 VDC) 1A Fuse
(+/- line)
* = Cut unused cores
and tape individually.
Wiring
Fix here.
55
9. INSTALLATION
This equipment can output navigation data to External Beacon Internal Beacon
external equipment, in NMEA 0183 format. Receiver Setting Receiver Setting
For example, it can output position data to a Output Output of internal
GGA beacon receiver's
radar or echo sounder for display on its MSK correction data
display screen. (correction data and
Input $CRMSS)
Correction data of
Output data format, data sentences external beacon
receiver
NMEA 0183 version 1.5, 2.0 or 2.1 can be
selected from the I/O SETUP menu. BEACON on WAAS/DGPS BEACON on WAAS/DGPS
SETUP menu set to SETUP menu set to
EXT INT
DATA1: Current loop data
Data sentence description
With waypoint
Sentence Description
AP REM1 REM2
AAM Arrival alarm
GLL GLL GLL
APB Autopilot data (XTE and bearing to
VTG GGA GGA waypoint)
ZDA VTG VTG BOD Bearing from own ship to
*2
AAM ZDA ZDA destination
APB *2
RMC RMA (Ver 2.0)*1 BWC Range and bearing to waypoint
(great circle navigation)
BOD*2 RMB*2 GTD (Ver 1.5)*1
GGA GPS position fixing condition (time
BWC*2 RMC
of fix, latitude, longitude, receiving
XTE *2
RMB*2 condition, number of satellites
BWC*2 used, DOP)
(1 s interval: GLL Latitude and longitude
(1 s interval) (1 s interval) Ver. 2.1 GTD Loran-C time difference
2 s interval:
RMA Generic navigational information
Ver. 1.5/2.0)
*1
(latitude, longitude, Loran-C time
: Output when Loran C TDs are displayed. differences, ground speed, true
*2
: Not output when no waypoint is set. course
AP: Autopilot RMB Generic navigational information
(cross track error, steering
REM1/REM2: Radar, echo sounder, etc. direction, starting waypoint no.,
destination waypoint no., latitude
DATA2: RS-232C level and longitude of starting waypoint,
With waypoint latitude and longitude of destination
waypoint, range and bearing to
AP REM
waypoint, range and bearing from
GLL GLL
present position to destination
VTG GGA
waypoint, velocity to destination,
ZDA VTG
arrival alarm)
AAM*2 ZDA
RMC Generic navigational information
APB*2 RMA (Ver 2.0)*1
(UTC time, latitude, longitude,
BOD*2 GTD (Ver 1.5)*1
ground speed, true course, day,
BWC*2 RMC month, year)
XTE*2 RMB*2
VTG Actual track and ground speeds
BWC*2
*1 XTE Course error amount and direction
: Output when Loran C TDs are displayed. to steer
*2
: Not output when no waypoint is set. ZDA UTC time (day, month, year)
56
9. INSTALLATION
57
9. INSTALLATION
58
APPENDIX
Menu Tree
ERASE WAYPOINTS/MARKS?
ROUTES?
TRACK?
RESET TRIP?
RESET ODO?
GPS DATA?
MENU SETTINGS?
ALL BACKUP DATA?
AP-1
APPENDIX
AP-2
APPENDIX
AP-3
APPENDIX
Loran C Chains
Chain GRI S1 S2 S3 S4 S5
Central Pacific 4990 11 29 – – –
Canadian East Coast 5930 11 25 38 – –
Commando Lion (Korea) 5970 11 31 42 – –
Canadian West Coast 5990 11 27 41 – –
South Saudi Arabia 7170 11 26 39 52 –
Labrador Sea 7930 11 26 – – –
Eastern Russia 7950 11 30 46 61 –
Gulf of Alaska 7960 11 26 44 – –
Norwegian Sea 7970 11 26 46 60 –
Southeast USA 7980 11 23 43 59 –
Mediterranean Sea 7990 11 29 47 – –
Western Russia 8000 10 25 50 65 –
North Central USA 8290 11 27 42 – –
North Saudi Arabia 8990 11 25 40 56 69
Great Lakes 8970 11 28 44 59 –
South Central USA 9610 11 25 40 52 65
West Coast USA 9940 11 27 40 – –
Northeast USA 9960 11 25 39 54 –
Northeast Pacific (old) 9970 11 30 55 81 –
Icelandic 9980 11 30 – – –
North Pacific 9990 11 29 43 – –
Suez 4991 10 24
England, France 8940 12 30
Northwest Pacific 8930 11 30 50 70
Newfoundland East Coast 7270 11 25
Lessay 6731 10 39
BØ 7001 11 27
Sylt 7499 11 26
Ejde 9007 10 23 38
Saudia Arabia North 8830 11 25 39 56
Saudia Arabia South 7030 11 25 37 55
AP-4
APPENDIX
Decca Chains
AP-5
APPENDIX
What Is WAAS?
WAAS (Wide Area Augmentation System), available in North America, is a provider in the
worldwide SBAS (Satellite Based Augmentation System) navigation system. This system
provides GPS signal corrections to SBAS users, for even better position accuracy, typically
better than three meters. There are three more SBAS providers, MSAS (Multi-Functional
Satellite Augmentation System) for Japan, EGNOS (Euro Geostationary Navigation Overlay
Service) for Europe and GAGAN (GPS And GEO Augmented Navigation) for India. The
illustration below shows the coverage area. (Accuracy may be affected when using a GEO
satellite not within your current location.) This manual uses “WAAS” for these three
providers generically.
EGNOS
WAAS
MSAS
GAGAN
AP-6
FURUNO GP-32/37
SPECIFICATIONS OF
GPS NAVIGATOR GP-32
DGPS NAVIGATOR GP-37
1 GPS RECEIVER
1.1 Receiving Channels
GPS 12 channels parallel, 12 satellites tracking
WAAS 1 channel
1.2 Rx Frequency 1575.42 MHz
1.3 Rx Code C/A code, WAAS
1.4 Position Accuracy
GPS 10 m (95% of the time, HDOP≤4)
DGPS 5 m (95% of the time, external data required)
WAAS 3 m (95% of the time)
1.5 Tracking Velocity 999 kt
1.6 Position-Fixing Time Warm start: 12 s approx., Cold start: 90 s approx.
1.7 Position Update interval 1 s
1.8 Beacon Receiver (GP-37 only)
Frequency Range 283.5 kHz to 325.0 kHz
MSK Rate 50,100,200 bps (Auto/Manual selectable)
2 RECEIVER UNIT
2.1 Display System Monochrome LCD, 95 (W) x 60 (H) mm, 120 x 64 dots
2.2 Display Mode Plotter, Steering, Highway, NAV data, Destination, User display
2.3 Projection Mercator
2.4 Memory Capacity Track: 1000 pts, Waypoint: 999 pts w/ comment
2.5 Storage Capacity 50 routes w/ 30 waypoint each
2.6 Alarms Arrival and anchor watch, Cross track error, Odometer alarm,
Ship’s speed in and out alarms, Time alarm, Trip alarm,
WAAS/DGPS alarm
2.7 Display Scale
Plotter Display 0.02/0.05/0.1/0.2/0.5/1/2/5/10/20/40/80/160/320 nm
Highway Display 0.2/0.4/0.8/1/2/4/8/16 nm
3 INTERFACE
3.1 Data 1 Current Loop
Output Data: NMEA0183 Ver 1.5/2.0/2.1 selected
NMEA-REM1: GLL, GGA, VTG, ZDA, RMC, RMB
SP - 1 E4420S01E-M
FURUNO GP-32/37
4 POWER SUPPLY
4.1 GP-32: 12-24 VDC: 240-120 mA
4.2 GP-37: 12-24 VDC: 340-170 mA
5 ENVIRONMENTAL CONDITION
5.1 Ambient temperature Antenna unit: -25°C to +70°C
Receiver unit: -15°C to +55°C
5.2 Relative humidity 93% or less (+40°C)
5.3 Degree of protection
Antenna unit IPX6
Receiver unit IPX5 (USCG CFR-46)
5.4 Vibration IEC 60945
6 COATING COLOR
6.1 Antenna unit N9.5
6.2 Receiver unit N3.0
SP - 2 E4420S01E-M
D-1
/CT 4'UWOK
Sep.29'05
D-2
17/May/2013 H.MAKI
Maki
電子署名者 : Maki
DN: cn=Maki, c=JP - 日本, o=FURUNO, ou=technicaldocument, email=hiromasa.maki@furuno.co.jp
日付 : 2013.05.17 17:18:45 +09'00'
15/May/2014 H.MAKI
D-2A
電子署名者 : Maki
DN: cn=Maki, c=JP -
日本, o=FURUNO,
Ma ou=technicaldocument
, email=hiromasa.
maki@furuno.co.jp
日付 : 2014.05.15
ki 16:33:09 +09'00'
1 2 3 4
空中線部
外部機器
例) ANTENNA UNIT
レーダー 受信演算部 GPA-017
魚群探知機
オートパイロット RECEIVER UNIT
リモートディスプレイ
A プロッタ GP-32
RD-H ANT TNC-P-3
EXT EQUIPMENT
EX: RD-C 3D-2V,10m,φ5.3
RADAR
ECHO SOUNDER
AUTOPILOT
REMOTE DISPLAY *2
PLOTTER MJ-A7SPF0009,2m MJ-A7SPFD J1 *4
シロ WHT 1 TD-H DATA1 CURRENT LOOP
NMEA0183(Ver1.5/2.0/2.1)
パーソナルコンピュータ SG アオ BLU 2 TD-C/SG
PC DATA2 RS-232C
外部ビーコン受信機 PC YEL NMEA0183(Ver1.5/2.0/2.1)
RD キ 3 SD
EXTERNAL BEACON RECEIVER RTCM SC-104
SD ミドリ GRN 4 RD UP LOAD/DOWN LOAD
船内電源 FUSE 1A (WP,ROUTE)
アカ RED 5 (+)
SHIP'S MAINS (+) 12-24VDC IN
12-24 VDC (-) クロ BLK 6 (-)
1A
7 FG
100/110/115/
220/230 VAC
B 1φ,50/60Hz (+)(-)
整流器 *1
RECTIFIER
GND *1
IV-1.25SQ
注記
*1)現地手配
*2)コネクタは工場にて取付済み
*3)オプション
C *4)メニューにより選択 DRAWN TITLE
May 13 '03 T.YAMASAKI GP-32
NOTE CHECKED 名称
*1. LOCAL SUPPLY. May 13 '03 T.TAKENO GPS航法装置
*2. FITTED AT FACTORY. APPROVED
May 13 '03 相互結線図
*3. OPTION.
SCALE MASS NAME
*4. SELECT ON MENU. kg GPS NAVIGATOR
S-1
DWG.No.
C4420-C01- B INTERCONNECTION DIAGRAM
1 2 3 4
空中線部
外部機器
例) ANTENNA UNIT
レーダー 受信演算部 GPA-019
魚群探知機
オートパイロット RECEIVER UNIT
リモートディスプレイ
A プロッタ GP-37
RD-H ANT TNC-P-3
EXT EQUIPMENT
EX: RD-C 3D-2V,10m,φ5.3
RADAR
ECHO SOUNDER
AUTOPILOT
REMOTE DISPLAY *2
PLOTTER MJ-A7SPF0009,2m MJ-A7SPFD J1 *4
シロ WHT 1 TD-H DATA1 CURRENT LOOP
NMEA0183(Ver1.5/2.0/2.1)
SG アオ BLU 2 TD-C/SG DATA2 RS-232C
パーソナルコンピュータ PC
PC RD キ YEL 3 SD NMEA0183(Ver1.5/2.0/2.1)
RTCM SC-104[OUTPUT]
SD ミドリ GRN 4 RD UP LOAD/DOWN LOAD
船内電源 FUSE 1A (WP,ROUTE)
アカ RED 5 (+)
SHIP'S MAINS (+) 12-24VDC IN
12-24 VDC (-) クロ BLK 6 (-)
1A
7 FG
100/110/115/
220/230 VAC
B 1φ,50/60Hz (+)(-)
整流器 *1
RECTIFIER
GND *1
IV-1.25SQ
注記
*1)現地手配
*2)コネクタは工場にて取付済み
*3)オプション
C *4)メニューにより選択 DRAWN TITLE
May 13 '03 T.YAMASAKI GP-37
NOTE CHECKED 名称
*1. LOCAL SUPPLY. May 13 '03 T.TAKENO DGPS航法装置
*2. FITTED AT FACTORY. APPROVED May 13 '03
相互結線図
*3. OPTION.
SCALE MASS NAME
*4. SELECT ON MENU. kg DGPS NAVIGATOR
S-2
DWG.No.
C4419-C01- B INTERCONNECTION DIAGRAM
INDEX
Digital display
A
overview ..................................................... 6
Alarms
setting up.................................................. 41
anchor watch ............................................30
DIM/PWR key................................................. 2
arrival ........................................................29
Dimmer........................................................... 2
buzzer type ...............................................32
DISP key ........................................................ 3
odometer...................................................32
Downloading data to a PC ........................... 43
speed ........................................................31
time ...........................................................31 E
trip .............................................................32 Erasing
WAAS/DGPS ............................................31 routes
XTE ...........................................................30 track...........................................................11
Alarms menu ................................................29 waypoints (marks) .................................... 17
Anchor watch alarm......................................30
F
Arrival alarm .................................................29
Fuse replacement ........................................ 48
B
G
Battery replacement .....................................48
Geodetic chart system
Bearing reference .........................................37
list ......................................................... AP-3
Buzzer...........................................................32
selection ................................................... 38
C GOTO key .............................................. 27, 28
Calculation menu..........................................33 GPS setup menu.......................................... 40
Centering (own ship mark) ...........................10
H
Clearing data ................................................50
Highway display ............................................. 4
Contrast ..........................................................2
Controls ..........................................................1 I
Cursor .............................................................9 Installation ................................................... 53
D L
Decca chains ............................................AP-5 Language ..................................................... 46
Destination Loran C chains ......................................... AP-4
canceling...................................................28 M
setting by cursor .......................................27 Magnetic variation........................................ 38
setting by route .........................................28 Maintenance................................................. 47
setting by user waypoint ...........................28 MARK/MOB key........................................... 15
setting by waypoint ...................................27 MENU key ...................................................... 7
DGPS Menu tree ................................................. AP-1
editing user channels................................36 Messages..................................................... 47
erasing all user channels..........................37 MOB mark .................................................... 15
erasing individual user channels ..............37
N
programming user channels.....................36
Nav data display ............................................ 5
setup .........................................................35
Diagnostics ...................................................49 O
Odometer alarm ........................................... 32
Odometer resetting ...................................... 42
Index-1
INDEX
P U
Plotter display ................................................ 4 Units of measurement ..................................38
Position offset .............................................. 40 Uploading data from a PC ............................44
User display
R
overview .....................................................6
Receiver status indications ............................ 2
setting up ..................................................41
Routes
User waypoint...............................................28
changing route name ............................... 25
creating track-based................................. 22 W
creating with cursor .................................. 19 WAAS
creating with waypoints ...................... 20, 21 description ............................................AP-6
deleting waypoints from ........................... 24 setup.........................................................34
destination................................................ 28 WAAS/DGPS alarm......................................31
erasing ..................................................... 25 WAAS/DGPS menu................................34, 35
inserting waypoints................................... 24 Waypoints (marks)
replacing waypoints.................................. 23 displaying name........................................16
skipping waypoints ................................... 24 editing .......................................................16
entering at own ship position ....................14
S
entering through the waypoint list.............14
Satellite disabling ......................................... 40
entering with cursor ..................................13
Satellite monitor ........................................... 49
erasing......................................................17
Shifting the display....................................... 10
setting as destination................................27
Simulation display .......................................... 8
user waypoint ...........................................28
Smoothing
waypoints/marks list (nearest) ..................17
position..................................................... 40
Wiring diagram .............................................43
speed/course............................................ 41
Speed alarm................................................. 31 X
Speed averaging .......................................... 40 XTE alarm ....................................................30
Speedometer display
Y
overview ..................................................... 6
Yeoman data loading....................................44
setting up.................................................. 42
Steering display.............................................. 5 Z
System configuration ....................................vii Zoom ..............................................................9
T
TD setup menu ............................................ 38
Time ............................................................. 39
Time alarm ................................................... 31
Track
erasing ..................................................... 11
plotting interval ......................................... 10
starting, stopping plotting ......................... 10
Trip alarm ..................................................... 32
Trip resetting ................................................ 42
Index-2
FURUNO Worldwide Warranty for Pleasure Boats (Except North America)
This warranty is valid for products manufactured by Furuno Warranty repairs carried out by companies/persons other than a
Electric Co. (hereafter FURUNO) and installed on a pleasure FURUNO national distributor or a certified dealer is not covered
boat. Any web based purchases that are imported into other by this warranty.
countries by anyone other than a FURUNO certified dealer may
not comply with local standards. FURUNO strongly recommends 6. Warranty Limitations
against importing these products from international websites as
the imported product may not work correctly and may interfere When a claim is made, FURUNO has a right to choose whether
with other electronic devices. The imported product may also be to repair the product or replace it.
in breach of the local laws and mandated technical requirements.
Products imported into other countries as described previously The FURUNO warranty is only valid if the product was correctly
shall not be eligible for local warranty service. installed and used. Therefore, it is necessary for the customer to
comply with the instructions in the handbook. Problems which
For products purchased outside of your country please contact result from not complying with the instruction manual are not
the national distributor of Furuno products in the country where covered by the warranty.
purchased.
FURUNO is not liable for any damage caused to the vessel by
This warranty is in addition to the customer´s statutory legal using a FURUNO product.
rights.
The following are excluded from this warranty:
1. Terms and Conditions of Warranty
a. Second-hand product
FURUNO guarantees that each new FURUNO product is the
b. Underwater unit such as transducer and hull unit
result of quality materials and workmanship. The warranty is
valid for a period of 2 years (24 months) from the date of the c. Routine maintenance, alignment and calibration
invoice, or the date of commissioning of the product by the services.
installing certified dealer.
d. Replacement of consumable parts such as fuses,
lamps, recording papers, drive belts, cables, protective
2. FURUNO Standard Warranty covers and batteries.
The FURUNO standard warranty covers spare parts and labour e. Magnetron and MIC with more than 1000 transmitting
costs associated with a warranty claim, provided that the product hours or older than 12 months, whichever comes first.
is returned to a FURUNO national distributor by prepaid carrier.
f. Costs associated with the replacement of a transducer
The FURUNO standard warranty includes: (e.g. Crane, docking or diver etc.).
Repair at a FURUNO national distributor g. Sea trial, test and evaluation or other demonstrations.
All spare parts for the repair
Cost for economical shipment to customer h. Products repaired or altered by anyone other than the
FURUNO national distributor or an authorized dealer.
3. FURUNO Onboard Warranty
i. Products on which the serial number is altered,
If the product was installed/commissioned and registered by a defaced or removed.
certified FURUNO dealer, the customer has the right to the
onboard warranty. j. Problems resulting from an accident, negligence,
misuse, improper installation, vandalism or water
The FURUNO onboard warranty includes penetration.
• Free shipping of the necessary parts k. Damage resulting from a force majeure or other natural
catastrophe or calamity.
• Labour: Normal working hours only
• Travel time: Up to a maximum of two (2) hours
l. Damage from shipping or transit.
• Travel distance: Up to a maximum of one hundred
and sixty (160) KM by car for the complete journey m. Software updates, except when deemed necessary
and warrantable by FURUNO.
4. Warranty Registration
n. Overtime, extra labour outside of normal hours such as
For the Standard Warranty - presentation of product with serial weekend/holiday, and travel costs above the 160 KM
number (8 digits serial number, 1234-5678) is sufficient. allowance
Otherwise, the invoice with serial number, name and stamp of
the dealer and date of purchase is shown. o. Operator familiarization and orientation.
For the Onboard Warranty your FURUNO certified dealer will
take care of all registrations.
FURUNO Electric Company, March 1, 2011
5. Warranty Claims
FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS
warranty on products from the date of installation or purchase by the original owner. Products or components that are
represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty
period stated above. The warranty start date may not exceed eighteen (18) months from the original date of purchase
by dealer from Furuno USA and applies to new equipment installed and operated in accordance with Furuno USA’s
published instructions.
Magnetrons and Microwave devices will be warranted for a period of 12 months from date of original equipment
installation.
Furuno U.S.A., Inc. warrants each new product to be of sound material and workmanship and through its authorized
dealer will exchange any parts proven to be defective in material or workmanship under normal use at no charge for a
period of 24 months from the date of installation or purchase.
Furuno U.S.A., Inc., through an authorized Furuno dealer will provide labor at no cost to replace defective parts,
exclusive of routine maintenance or normal adjustments, for a period of 24 months from installation date provided the
work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius
of 50 miles of the shop location.
A suitable proof of purchase showing date of purchase, or installation certification must be available to Furuno U.S.A.,
Inc., or its authorized dealer at the time of request for warranty service.
This warranty is valid for installation of products manufactured by Furuno Electric Co. (hereafter FURUNO). Any
purchases from brick and mortar or web-based resellers that are imported into other countries by anyone other than a
FURUNO certified dealer, agent or subsidiary may not comply with local standards. FURUNO strongly recommends
against importing these products from international websites or other resellers, as the imported product may not work
correctly and may interfere with other electronic devices. The imported product may also be in breach of the local
laws and mandated technical requirements. Products imported into other countries, as described previously, shall not
be eligible for local warranty service.
For products purchased outside of your country please contact the national distributor of Furuno products in the
country where purchased.
Furuno U.S.A., Inc. is proud to supply you with the highest quality in Marine Electronics. We know you had several
choices when making your selection of equipment, and from everyone at Furuno we thank you. Furuno takes great
pride in customer service.