Professional Documents
Culture Documents
User Manual: LAST UPDATED: 2011.11.16
User Manual: LAST UPDATED: 2011.11.16
User Manual: LAST UPDATED: 2011.11.16
co
LAST UPDATED : 2011.11.16
compatible with VW car models with RNS510
.
ns
io
RNS 510
ut
ol
User manual
-S
ar
C
Contents
m
1. Before the installation
co
1.1 Main specification 3
1.2 Features 4
1.3 System diagram 5
.
1.4 Components 6
ns
1.5 Exterior 7
2. Setup
io
2.1 DIP switch 8
2.2 KEYPAD 9
ut
2.3 Factory mode 10
2.4 Rear parking guide line 11
2.5 OSD (on screen display) 13
ol
-S
3. Troubleshooting 14
ar
C
2
1.1 Main specification
m
1. Input Spec. (VIDEO INTERFACE)
-3x A/V Input (Rear video source)
co
-1x CVBS(Rear camera) Input (Rear camera source)
-1x Analog RGB Input (Navigation System output)
-1x LCD Input (Car system Input)
.
ns
2. Output Spec.
- 1 x LCD Output (LCD operation)
- 4 x Audio Select (12V power comes out from 4 wires of cable by video, Navigation mode)
io
3. Power Spec.
ut
- Input power : 10VDC ~ 16VDC
- Power consumption : 6WATT in maximum level
ol
4. Switching mode
- Skip function of input video : Able to skip each input source via adjusting DIP switch.
-S
- Able to change a mode to another by using the mode switch.
- Able to change modes and get back to the OEM screen through the genuine buttons.
ar
C
3
1.2 Features
m
Clear high definition screen
co
NTSC, PAL system support
.
ns
Mode exchange via the original buttons
io
Additional function of adjusting the screen size of NAVI
ut
ol
-S
ar
C
4
1.3 System diagram
m
Keypad Switch for source toggle
co
OEM Mavi Button (TIM)
.
(Analog RGB)
ns
Car Installation
DISPLAY OEM LCD
A/V 1
io
VIDEO MUX
A/V 2 VIDEO
A/V 3 CIRCUIT
CVBS
(Rear camera)
ut
ol
Car Screen Input
-S
POWER A/V OUT
(CAR MAIN BOARD)
CIRCUIT HEADREST
MONITOR
ar
(+10VDC ~ +16VDC)
5
1.4 Components
m
co
FPC cable * 1pc. Sub board * 1pc. Extension cable * 2pc.
.
(FPCABL0011) (QCPASS0041) (HTOUCH0001)
ns
(HTOUCH0002)
io
TOUCH cable * 1pc. Button cable * 1pc. FFC cable * 2pc.
(HTOUCH0003) (HBUTTO0003) (FFCABL0006)
ut
ol
POWER cable (10P) * 1pc.
(HPOWER0005)
LVDS cable * 1pc. IR cable (8P) * 1pc.
Ground cable * 1pc.
-S
(HLVDSC0006) (HIRCAB0003)
(HGROUN0001)
OR
Mode cable * 1pc.
(HARETC0001)
ar
Keypad * 1pc.
AV cable * 1pc. Remote control * 1pc. (SMTASY0063)
C
6
1.5 Exterior
m
⑤ ⑥ ⑦ ⑧
co
Product dimension
155mm (Horizontal length)
⑧ ⑦ ⑥ ⑤
.
93mm (Vertical length)
ns
20mm (Height)
① POWER
io
② MODE
③ RGB (IN)
ut ④ AV(IN/OUT)
ol
⑤ LCD OUT
⑥ KEYPAD
-S
① ② ③ ④ ⑦ DIP S/W
⑧ LED
ar
C
① ② ③ ④
7
2.1 DIP switch
m
#PIN Function DIP S/W selection ※ ON : DOWN, OFF : UP default : all OFF
co
ON : RGB mode OFF ※ DIP S/W usage example
1 RGB INPUT skip
OFF : RGB Display
- Input mode use : A/V2, A/V3
ON : A/V1 mode OFF
.
2 A/V 1 skip - Use original navigation
OFF : A/V1 Display
ns
▷ DIP S/W : 1,2 ON (INPUT MODE SKIP)
ON : A/V2 mode OFF
3 A/V 2 skip ▷ DIP S/W : 3 OFF (enable A/V2)
OFF : A/V2 Display ▷ DIP S/W : 4 OFF (enable A/V3)
io
ON : A/V3 mode OFF ▷ DIP S/W : 5, 6, 7 OFF
4 A/V 3 skip ▷ DIP S/W : 8 ON
OFF : A/V3 Display
5 NOT USED
ut
ol
6 NOT USED
-S
ON : REAR CAMERA mode ON
7 Rear mode
OFF : MAIN rear camera
ar
AV1~3
8
2.2 KEYPAD
m
※ FACTORY MODE (Interface setting)
: Press “UP” button about 2 seconds long and you will approach FACTORY mode. Also you can get there in
pressing these keys in this sequence; “UP” → “DOWN” → “UP” → “MENU”
. co
ns
io
Key Function
MENU/EXIT
ut
Implement OSD screen
ol
SEL/INPUT Selection
UP Move upward, if you press about 2 seconds long, you are able to approach the FACTORY mode.
-S
DOWN Move downward, if you press about 2 seconds long, you are able to reset the factory mode.
ar
C
9
2.3 Factory mode
m
※ FACTORY mode – Press “UP” button on the keypad long about 2 seconds or press these buttons
in this sequence; “UP”→”DOWN”→”UP”→”MENU”
. co
ns
io
ut
IMAGE PARK UTIL
- H-POSITION : control over the - PARK ENABLE : able to choose - NAVI SELECT (N.C)
horizontal position of the screen whether the rear guide line is - AVOUT SELECT : making a choice of
ol
- V-POSITION : control over the displayed or not with rear gear. AVOUT output in the OEM & NAVI
vertical position of the screen (default-ON) screen (Default – AV3)
- H-SIZE : control over the size of -PARK SETUP : able to adjust the - FACTORY RESET : reset
-S
NAVI screen position of the rear guide line with
the keypad.
- SAFE ENABLE : The function that
ar
10
2.4 Rear parking guide line
m
※ FACTORY mode – Press “UP” button on the keypad long about 2 seconds.
co
parking guide line will automatically appear on the
screen like the left picture.
※ FACTORY default : DISPLAY - ENABLE
.
ns
io
ut ② If you press “UP” button on the keypad about 2
ol
seconds long, you can see the left image on the
screen. Now that you choose “PARK SETUP” and
-S
press “OK” on the keypad, you can control the width
of the rear parking guide line.
ar
C
11
2.4 Rear parking guide line
m
※ FACTORY default -Types:0, H_Pos:50, V_Pos:120
co
~
.
ns
io
level 0 level 4
③ The width of the rear parking guide line has 5 level(0~4). After you control the level with “UP”,
ut
“DOWN” button on the keypad, you can move to the horizontal positioning mode after pressing “SEL”
button and saving process. ( The current state is displayed right-top. )
ol
④ After you control the horizontal position with “UP”,
“DOWN” button on the keypad, you can move to the
-S
vertical positioning mode after pressing “SEL” button and
saving process. Once you finish that and press “SEL”, all the
things will be saved. ( Adjustable between level 0 and level
ar
255. )
※ Unless you want the rear parking guide line, set the
C
12
2.5 OSD (on screen display)
m
※ OSD : Press “MENU” button on the keypad.
. co
ns
Analog RGB Mode Analog RGB Mode Analog RGB Mode
io
ut
ol
Video Mode Video Mode Video Mode
-S
IMAGE OSD UTIL
- BRIGHTNESS : adjusting brightness - LANGUAGE : choice of language - FACTORY RESET : able to reset the
- CONTRAST : adjusting contrast - TRANSPARENT : control over the whole value of the NAVI or AV
ar
13
3. Troubleshooting
m
Q. I can not switch A/V sources.
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
co
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
ns
Q. Displayed image color is not proper. (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform the manufacturer.)
io
Q. Rear camera image does NOT appear.
ut
A. Set DIP switch #7 in “ON”
14