Professional Documents
Culture Documents
Amplifier: Electronics & Software
Amplifier: Electronics & Software
Technical Data
–5 % kHz >5,5
–3 dB kHz 9
Load resistance Ω ≤550
Operating temperature range °C 0 ... 60
Page 1/3
This information corresponds to the current state of knowledge. Kistler reserves ©1998 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, Fax +41 52 224 14 14, info@kistler.com, www.kistler.com
from the use of Kistler products is excluded. Kistler is a registered trademark of Kistler Holding AG.
Amplifier – for Measuring of Pressure and Temperature, Type 4618A0, 4618A2, 4618A4
Housing Zero fine and range fine are adjusted by internal potentio-
Dimensions mm 98x64x34 meters. Zero can be readjusted after opening the screw cap.
Material aluminum
Degree of protection IP65 For replacing the pressure sensor, the standardizing plug must
Weight g 250 be also replaced. The values for the sensitivity and the zero
of the sensor are given in the calibration sheet and can be
adjusted with the built-in calibrator.
Mounting
The amplifier housing Fig. 1 may be mounted to any support The temperature signal, however, can only be calibrated by
with M4 bolts. The aluminum housing is connected to ground Kistler.
in order to provide electrical shielding for the electronics.
Two additional internal potentiometers are available for adjust-
ing the limit switches. The switching levels may be adjusted
with a variable pressure or with a voltage taken from the elec-
tronic circuit. With the cover of the amplifier housing open, a
schematic of the electronics can be found inside which shows
the positions of the potentiometers and slide switches.
4618A_000-293e-09.11
Fig. 1: Housing
Page 2/3
This information corresponds to the current state of knowledge. Kistler reserves ©1998 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland
the right to make technical changes. Liability for consequential damage resulting Tel. +41 52 224 11 11, Fax +41 52 224 14 14, info@kistler.com, www.kistler.com
from the use of Kistler products is excluded. Kistler is a registered trademark of Kistler Holding AG.
Amplifier – for Measuring of Pressure and Temperature, Type 4618A0, 4618A2, 4618A4
8 Supply
+15V
GND
18 ... 30 V
2
–15V
GND
Measure
Calibration Voltage/Current
1 (4,5)
+IN Transmitter
4 ... 20 mA
RANGE
DA - 10 Ohm
(4) Pressure Output
4 VA
–OUT 0 ... 10 V
+
1
C
Limit Limit
2 Switch 1 6 Switch 1
–IN E
R Cal
3
C
Limit Limit
Switch 2 7 Switch 2
E
3 Cal ZERO, Measure
Cal RANGE
ZERO
Shield
–OUT Included Accessories Type/Art. No.
• Standardizing plug for specific 4958A0
1
sensor SN...
3 • 8 pin connector for power supply, 1500A57
–IN
2 4 output and limit switches, IP67,
3 4 +IN
1 5 DIN 4532
2
Optional Accessories Type/Art. No.
+OUT • Extension cable PVC for pressure 4757A5/A10
Fig. 3: Pin assignment of input and output sensors Types 4065/67
• Connecting cable PVC for pressure 4765A2/A5/A10
Output (Type 4618A0) Output (Type 4618A2) sensors Types 4043/45 and 4053
1 Limit Switch 1 Collector 1 Limit Switch 1 Collector • Connecting cable PVC for pressure 4767A2/A5/A10
2 GND 2 GND sensors Types 4073/75
3 Limit Switch 2 Collector 3 Limit Switch 2 Collector • 5 pin connector for pressure sensor 1500A81
4 Signal 0 ... 10 V 4 Signal 0 ... 10 V
5 Signal 4 ... 20 mA 5 Temperature Signal 10 mV/K
6 Limit Switch 1 Emitter 6 Limit Switch 1 Emitter Ordering Key
7 Limit Switch 2 Emitter 7 Limit Switch 2 Emitter Type 4618A
4618A_000-293e-09.11