Professional Documents
Culture Documents
High Back-Pressure Foam Makers: Data/Specifications
High Back-Pressure Foam Makers: Data/Specifications
Data/Specifications
FEATURES SPECIFICATIONS
䡲 Ten standard sizes to handle a wide range of flow requirements The high back-pressure foam maker assembly shall consist of an
anodized aluminum body and discharge tube. The internal foam turbula-
䡲 Compatible with ANSUL® fluoroprotein and AFFF concentrates for
tor and metering orifice shall be machined from stainless steel and sized
subsurface injection
to match the designated flow rate and corresponding model designation.
䡲 Designed to operate with total back pressure as high as 40% of inlet
pressure Each of the nominal 100 to 300 gpm (379 to 1136 Lpm) assemblies
shall be provided with a 2 1/2 in. NPT female inlet and 2 1/2 in. NPT
䡲 Cylindrically-shaped air inlet screen to help prevent accidental male outlet. Each of the nominal 350 to 550 gpm (1324 to 2082 Lpm)
damage or blockage assemblies shall be provided with a standard ANSI 4 in. pipe flange inlet
and 6 in. pipe flange outlet. Portable foam makers shall be equipped with
female swivel inlet and male outlet adaptors to mate the 2 1/2 in. NPT
thread to the specified fire hose thread.
APPLICATION
The high back-pressure foam maker shall have a stainless steel air inlet
ANSUL High Back-Pressure Foam Makers (HBPFM) are designed to screen that is cylindrically shaped to the air inlet surface to help ensure
generate expanded foam for the purpose of subsurface injection into a optimum performance and avoid damage. A pressure gauge, 0 to
cone-roof liquid hydrocarbon storage tank.* The foam maker is typically 300 psi (0 to 20.69 bar), shall be provided in the foam maker body to
located outside the diked area surrounding the storage tank. Expanded monitor operating pressure. A pressure gauge shroud shall be integral to
foam is injected through a dedicated foam line or into a product line to the cast metal body to help prevent gauge damage.
the storage tank (refer to Typical Schematics).
The high back-pressure foam maker is capable of generating expanded
foam within the optimum expansion ratio range of 2:1 to 4:1 for subsur- ORDERING INFORMATION
face injection. The foam maker can discharge against a back pressure
as high as 40% of the operating inlet pressure. A minimum foam maker Approx.
inlet pressure of 100 psi (6.9 bar) is typically required for satisfactory Nominal Shipping
operation. Flow Rate Weight
Part No.
_______ Model
____________ Application
_________ gpm (Lpm)
____________ lb (kg)
________
High back-pressure foam makers can be used with various types of pro-
portioning equipment including bladder tanks, balanced pressure pump 71240 HBPFM-100 Fixed 100 (379) 10 (4.5)
proportioning systems, in-line balanced pressure proportioning systems, 71241 HBPFM-150 Fixed 150 (568) 10 (4.5)
and foam trucks. (Line proportioning systems are usually unacceptable 71242 HBPFM-200 Fixed 200 (757) 10 (4.5)
due to the relatively high pressure loss across the line proportioner – 71243 HBPFM-250 Fixed 250 (946) 10 (4.5)
except in instances where back pressure to the foam maker is low and 71244 HBPFM-300 Fixed 300 (1136) 10 (4.5)
available water pressure to the line proportioner is relatively high.) 71286 HBPFM-350 Fixed 350 (1324) 38 (17.2)
* The flammable liquid being protected must be a hydrocarbon product. Polar solvent flamma- 71287 HBPFM-400 Fixed 400 (1514) 38 (17.2)
ble liquids or hydrocarbons containing more than 10% alcohol are destructive to subsurface 71288 HBPFM-450 Fixed 450 (1703) 38 (17.2)
injected foams. See NFPA 11.
71289 HBPFM-500 Fixed 500 (1893) 38 (17.2)
The storage tank protected should be of cone-roof construction without any type of internal 71290 HBPFM-550 Fixed 550 (2082) 38 (17.2)
floater. NFPA 11 does not recommend subsurface injection systems for open top or covered
floating roof tanks because of the possibility of improper distribution of foam to the fuel 71245 HBPFM-P-100 Portable 100 (379) 12 (5.4)
surface.
71246 HBPFM-P-150 Portable 150 (568) 12 (5.4)
71247 HBPFM-P-200 Portable 200 (757) 12 (5.4)
71248 HBPFM-P-250 Portable 250 (946) 12 (5.4)
71249 HBPFM-P-300 Portable 300 (1136) 12 (5.4)
DESCRIPTION
HIGH
BACK-
PRESSURE
FOAM MAKER
BLOCK
LIQUID BLOCK LIQUID
VALVE
HYDRO- VALVE CHECK HYDRO-
CARBON VALVE CARBON CHECK
VALVE
HIGH
BACK-
PRESSURE
DEDICATED FOAM SHUT-
MAKER DIKE OFF
FOAM LINE
VALVE
WATER 001261 WATER
LEVEL LEVEL PRODUCT 001262
DIKE
LINE
001263
BODY
SCREEN OUTLET ADAPTOR
SWIVEL INLET (PORTABLE MODELS)
ADAPTOR (PORTABLE
MODELS)
BODY
SCREEN
6 IN. OUTLET
FLANGE
4 IN. INLET 001264
FLANGE
DIMENSIONS
4 IN
(10.2 cm)
2 1/2-8 NPT
001265
9 IN 11 IN
(22.9 cm) (27.9 cm)
0.75 IN 0.88 IN
(19 mm) (22 mm) 001266
5 IN
(12.7 cm)
(kPa)
____ psi
___ 001268
(1724) 250
00
00
00
50
50
50
50
00
00
50
M-4
M-1
M-2
M-4
M-3
M-1
M-2
M-3
M-5
M-5
PF
PF
PF
PF
PF
PF
PF
PF
PF
PF
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
(1379) 200
INLET PRESSURE
(1034) 150
(690) 100
(483) 70
(345) 50
40 60 80 100 150 200 300 400 600 800 gpm
(151) (227) (303) (379) (568) (757) (1136) (1514) (2271) (3028) (Lpm)
FLOW RATE
ANSUL is a trademark of Ansul Incorporated or its affiliates.