Professional Documents
Culture Documents
CS WAVE Installation Manual
CS WAVE Installation Manual
CS WAVE Installation Manual
This document describes the procedure for installing the CS WAVE software components:
- Control centre
- Server.
in partnership with
CS WAVE installation manual – V1.2
Page 2 of 22
CS WAVE installation manual – V1.2
TABLE OF CONTENTS
1. LIST OF FIGURES 4
2. INTRODUCTION 5
3. VIRTUAL WELDING WORKBENCH 5
3.1 PRE-REQUISITES ............................................................................................................... 5
3.2 INSTALLATION.................................................................................................................. 5
4. CONTROL CENTRE 6
4.1 PRE-REQUISITES ............................................................................................................... 6
4.2 INSTALLATION.................................................................................................................. 6
4.3 UNINSTALLATION .......................................................................................................... 11
5. SERVER 14
5.1 PRE-REQUISITES ............................................................................................................. 14
5.2 INSTALLATION................................................................................................................ 14
5.3 UNINSTALLATION .......................................................................................................... 20
Page 3 of 22
CS WAVE installation manual – V1.2
1. LIST OF FIGURES
FIGURE 1 – CONTROL CENTRE LANGUAGE SELECTION ................................................................ 6
FIGURE 2 – INITIALIZATION OF CONTROL CENTRE SETUP ............................................................ 7
FIGURE 3 – CHOICE OF CONTROL CENTRE DIRECTORY ................................................................ 7
FIGURE 4 – CONTROL CENTRE SETUP .......................................................................................... 8
FIGURE 5 – END OF CONTROL CENTRE SETUP .............................................................................. 8
FIGURE 6 – CONTROL CENTRE CONFIGURATION TOOL................................................................. 9
FIGURE 7 – CONTROL CENTRE IDENTIFICATION INFORMATION.................................................. 10
FIGURE 8 - CS WAVE FIELDS OF CONTROL CENTRE ................................................................. 10
FIGURE 9 – CONTROL CENTRE ACTIVE LICENSE ........................................................................ 11
FIGURE 10 – LANGUAGE SELECTION ......................................................................................... 12
FIGURE 11 – DELETION CONFIRMATION .................................................................................... 12
FIGURE 12 – CONFIRMATION OF DATABASE DELETION ............................................................. 12
FIGURE 13 – END OF CONTROL CENTRE UNINSTALL PROCEDURE .............................................. 13
FIGURE 14 – SERVER LANGUAGE SELECTION ............................................................................ 15
FIGURE 15 – INITIALIZATION OF SERVER SETUP ........................................................................ 15
FIGURE 16 – CHOICE OF SERVER INSTALLATION DIRECTORY .................................................... 16
FIGURE 17 – SERVER FILE COPY ................................................................................................ 17
FIGURE 18 – END OF SERVER SETUP .......................................................................................... 18
FIGURE 19 – SERVER CONFIGURATION TOOL ............................................................................ 19
FIGURE 20 – SERVER IDENTIFICATION INFORMATION ............................................................... 19
FIGURE 21 - SERVER CS WAVE FIELDS ................................................................................... 20
FIGURE 22 – SERVER ACTIVE LICENSE ...................................................................................... 20
FIGURE 23 – LANGUAGE SELECTION ......................................................................................... 21
FIGURE 24 – SERVER DELETION CONFIRMATION ....................................................................... 21
FIGURE 25 – CONFIRMATION OF DATABASE DELETION ............................................................. 21
FIGURE 26 – END OF SERVER UNINSTALL PROCEDURE .............................................................. 22
Page 4 of 22
CS WAVE installation manual – V1.2
2. INTRODUCTION
This document describes the required environment and the procedures for installation of the
CS WAVE components:
- welding workbench
- control centre
- server
Be sure to carefully read this document before you begin the installation procedure.
3.1 PRE-REQUISITES
Before you install a CS WAVE virtual welding workbench in a training workshop, be sure the
following requirements have been observed:
- System is installed in a room protected from the workshop environment, but near the
workshop. The basic idea is to ensure that the workbench is protected from workshop
dust. The workbench should not however be too far from the workshop since the
trainees will be going back and forth several times from one location to the other.
- Reflections should be limited as far as possible; these can be created on the screen by
windows, doors and lights. The workbench should be installed in a covered box. If this
is not possible, ensure that the room lighting does not generate any significant
reflections on the two positions of the screen (vertical and horizontal).
- Proper workbench routing should be ensured (passage via doors, hallways, etc.).
- A pallet truck should be available on the day of delivery for unloading.
- A network connector RJ45 should be available with an IP address assigned for the
workbench.
- A power outlet.
- If used as part of a network within a training centre, the CS WAVE server must be
installed beforehand (see chapter 5) and all its characteristics (in particular, its IP
address) must be known.
3.2 INSTALLATION
Final installation of the workbench (installation of software and startup) is ensured by a
specialized technician. The technician will intervene once the workbench has been installed at
its final location. Updates, corrections and upgrades will also be ensured in the same way by
CS SI. Unless otherwise specified by CS SI, the user is not authorized to open the workbench
to access the system.
The workbench has its own security system against micro-cutouts, power cutouts and network
intrusions.
Once the final installation procedure has been completed by the specialized technician, the
workbench is operational.
Page 5 of 22
CS WAVE installation manual – V1.2
4. CONTROL CENTRE
4.1 PRE-REQUISITES
The CS WAVE control centre application is a software which is installed on an existing PC
(trainer workstation, in particular).
The machine must satisfy the following minimum requirements:
- Processor: Pentium III 1GHz
- Ram: 256 MB
- Hard disk: 80 GB
- Operating system: Windows NT, 2000 or XP
If a control centre is to be installed on the machine hosting the CS WAVE server, you must
start by installing the server (see chapter 5).
4.2 INSTALLATION
The CS WAVE distribution has a WaControl directory.
To start installing the CS WAVE control centre, go to this directory and run the setup.exe
program.
An automated installation program will guide you step by step in installing the application on
your workstation.
The following window will then be displayed to indicate that the setup is initializing.
Page 6 of 22
CS WAVE installation manual – V1.2
You must now choose the folder in which the CS WAVE control centre will be installed. By
default, the application installs it in directory: c:\program files\CS\WaControl.
A customized folder can be defined by clicking « Browse… ».
Once you have made your choice, click the « Next » button to continue the setup procedure.
Page 7 of 22
CS WAVE installation manual – V1.2
On completion of the setup procedure, a final window indicates that the CS WAVE server is
now installed on your workstation. Click « Finish » to exit the setup program.
Page 8 of 22
CS WAVE installation manual – V1.2
A « Control centre » icon is now displayed on the workstation WINDOWS desktop. This
will allow you to quickly launch the application (see user manual for CS WAVE control
centre).
The last step in the setup procedure consists in generating a valid license file in order to
execute the CS WAVE control centre. An icon entitled « Control centre configuration » is
displayed on the WINDOWS desktop and will allow you to execute the configuration tool for
the CS WAVE control centre.
Start the configuration tool; a window comes up showing the information required to generate
the license file.
Contact CS WAVE support and indicate the identification information on the workstation on
which the application has been installed.
Page 9 of 22
CS WAVE installation manual – V1.2
CSW WAVE support will then return you a code. Copy this code in the « CS WAVE code »
field.
Page 10 of 22
CS WAVE installation manual – V1.2
Click on the « Generate license file » button. The license file is then generated and the
information on the active license is updated.
4.3 UNINSTALLATION
To delete the CS WAVE control centre from your workstation, first check that the application
is stopped (see CS WAVE control centre installation manual).
The uninstall program for the CS WAVE control centre is then launched.
Select the uninstall program language:
Page 11 of 22
CS WAVE installation manual – V1.2
The program will then request you to confirm complete deletion of the CS WAVE and its
database.
A final message will ask you to confirm deletion of all the data contained on the workstation
(user profiles, results…).
The uninstall program stops the database manager, deletes the database and all the program
elements.
Page 12 of 22
CS WAVE installation manual – V1.2
Page 13 of 22
CS WAVE installation manual – V1.2
5. SERVER
5.1 PRE-REQUISITES
The CS WAVE server application is a software which is installed on an existing PC. We
recommend that you use a machine dedicated to this purpose, though this is not mandatory.
The machine must satisfy the following requirements:
- Processor: Pentium III 1GHz
- RAM: 512 MB
- Hard disk: 80 GB
- Operating system: Windows NT, 2000 or XP
Before installing a CS WAVE server, be sure that the following requirements have been
observed:
- The PC must be connected to the same network as that on which the workbenchs
are to be installed.
- The Windows user account with which the server is installed and used must
have Administrator rights.
- The workstation must remain on during the week to ensure backup archiving of
CS WAVE data.
- There should not be any databases under MySQL since the server will use this
application to manage its own database.
- Since the CS WAVE server will be installed on this PC, it is essential that it is
secure and stable (no virus, firewall protection, no « wild » installations). It is
the training centre’s responsibility to ensure that the machine environment is
sound.
- Ideally, to allow monitoring of the results by outside observers and maintenance by
CS SI, it would be useful that this PC have a fixed IP address which can be accessed
from the outside on the https protocol only (port 443).
5.2 INSTALLATION
Page 14 of 22
CS WAVE installation manual – V1.2
The following window is then displayed to indicate that the setup has been completed.
You must then choose the folder in which the CS WAVE server will be installed. By default,
the application is installed in directory: c:\program files\CS\WaServer.
A customized folder can be defined by clicking « Browse… ».
Once you have chosen your location, click the « Next » button to continue the setup
procedure.
Page 15 of 22
CS WAVE installation manual – V1.2
Page 16 of 22
CS WAVE installation manual – V1.2
At the end of the installation procedure, a final window is displayed indicating that the CS
WAVE server is now installed on the workstation. Click « Finish » to exit the setup program.
Page 17 of 22
CS WAVE installation manual – V1.2
The last step in the setup procedure consists in generating a valid license file in order to
execute the CS WAVE server. An icon entitled « Server configuration » is displayed on the
WINDOWS desktop and will allow you to execute the configuration tool for the CS WAVE
server.
Start the configuration tool; a window comes up showing the information required to generate
the license file.
Page 18 of 22
CS WAVE installation manual – V1.2
Contact CS WAVE support and indicate the identification information on the workstation on
which the application has been installed.
CSW WAVE support will then return you a code. Copy this code in the « CS WAVE code »
field.
Page 19 of 22
CS WAVE installation manual – V1.2
Click on the « Generate license file » button. The license file is then generated and the
information on the active license are updated.
5.3 UNINSTALLATION
To delete the CS WAVE server from your workstation, first check that the server is stopped
(see CS WAVE server User Manual).
Page 20 of 22
CS WAVE installation manual – V1.2
The program will then request you to confirm complete deletion of the CS WAVE server and
its database.
A final message will ask you to confirm deletion of all the data contained in the server (user
profiles, results…). Since the server forms the data reference, deleting the server will result in
loss of this data for all the associated modules (workbenchs and control centres).
Page 21 of 22
CS WAVE installation manual – V1.2
The uninstall program will then stop the database manager and delete the database and all the
program elements.
Page 22 of 22