Professional Documents
Culture Documents
3 Engine Speed Change
3 Engine Speed Change
3 Engine Speed Change
h a n g e Pro
Service Information System Page 1 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
tr re tr re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
Testing and Adjusting
308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B
Excavators Engine and Pump Control
Media Number -RENR1998-06 Publication Date -01/10/2004 Date Updated -06/10/2004
i01256784
Parameter - Adjust
SMCS - 1931-025-NQ
View Image
Illustration 1 g00662996
Monitor Panel
The character display identifies the type of oil that has been selected. Mineral oil or biological
oil may be selected.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020
XC
h a n g e Pro
Service Information System Page 2 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
tr tr
re
2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
3. Depress the boom priority mode switch (23) in order to select the mineral oil. "Std" "80Std".
4. Depress the swing priority mode switch (24) in order to select the biological oil. "b10" "80b1o".
a. Depress travel alarm cancel switch (22) in order to set the new value.
When the new value is set, the position of the blinking character does not change. The
service code will flash.
2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the fourth position from the right.
3. Depress boom priority mode switch (23) in order to INCREASE the speed setting by 10 RPM.
The speed setting can be set at any speed that is between 800 RPM and high idle.
4. Depress swing priority mode switch (24) in order to DECREASE the speed setting by 10 RPM.
The speed setting can be set at any speed that is between 800 RPM and high idle.
a. Depress travel alarm cancel switch (22) in order to set the new values.
When the new value is set, the position of the blinking character does not change. The
service code flashes.
The character display indicates the current time delay in 0.1 second.
2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the second position from the right.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020
XC
h a n g e Pro
Service Information System Page 3 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
tr tr
re
3. Depress boom priority mode switch (23) in order to INCREASE the setting of the time delay by re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
0.5 second.
4. Depress swing priority mode switch (24) in order to DECREASE the setting of the time delay
by 0.5 second.
a. Depress travel alarm cancel switch (22) in order to set the new values.
When the new value is set, the position of the blinking character does not change. The
service code flashes.
When the machine is secured, the machine automatically defaults to the work mode and the power
mode. Also, the travel speed automatically defaults to the LOW speed position. This is accomplished
regardless of the state of the memory mode.
The memory mode may be turned "ON" or turned "OFF". Display (1) indicates the state of the
memory mode. The mode can be "on" or "oF".
2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the position on the right.
3. Depress boom priority mode switch (23) in order to turn the mode "ON". "83on".
4. Depress swing priority mode switch (24) in order to turn the mode "OFF". "83oF".
a. Depress travel alarm cancel switch (22) in order to set the new values.
When the new value is set, the position of the blinking character does not change. The
service code flashes.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020
XC
h a n g e Pro
Service Information System Page 4 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
Reduced Setting Of Horsepower (Attachment Pump)
tr re tr re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
When an attachment pump is installed on the machine, the engine will maintain the target speed. This
is done until a maximum of 30 percent of the available engine horsepower is used by the attachment
pumps. Service code 84 is used to adjust the upper limit of the main pump horsepower.
The character display indicates the upper limit of the main pump. The value is displayed in
percent.
2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the right two positions.
3. Depress the boom priority mode switch (23) in order to INCREASE the upper limit by 5
percent.
4. Depress the swing priority mode switch (24) in order to DECREASE the upper limit by 5
percent.
a. Depress the travel alarm cancel switch (22) in order to set the new values.
When the new value is set, the position of the blinking character does not change. The
service code flashes.
The character display indicates the engine speed setting that is used by the low idle switch. The
value is displayed in RPM.
2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the right two positions.
3. Depress the boom priority mode switch (23) in order to INCREASE the speed setting by 10
RPM.
The speed setting can be between 800 RPM and high idle.
4. Depress the swing priority mode switch (24) in order to DECREASE the speed setting by 10
RPM.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020
XC
h a n g e Pro
Service Information System Page 5 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
tr tr
re
The upper limit can be between 800 RPM and high idle. re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
a. Depress the travel alarm cancel switch (22) in order to set the new values.
When the new value is set, the position of the blinking character does not change. The
service code flashes.
1. Enter service code 66. The character display shows the current power shift pressure in kPa.
2. Depress the fine control mode switch (25) in order to shift the blinking position of the character
display to the fourth character position from the right.
3. When the boom priority mode switch (23) is depressed, the command signal of the power shift
pressure is increased by 10 kPa (1.5 psi).
4. When the swing priority mode switch (24) is depressed, the command signal of the power shift
pressure decreases by 10 kPa (1.5 psi).
5. When the boom priority mode switch (23) and the power mode switch (19) are depressed
simultaneously, the command signal to the power shift pressure increases by 200 kPa (29 psi).
6. When the swing priority mode switch (24) and the power mode switch (19) are depressed
simultaneously, the command signal to the power shift pressure decreases by 200 kPa (29 psi).
Note: The engine speed cannot be checked with the monitor panel while you are in the mode of
fixed power shift pressure.
7. The engine speed will be displayed, if the service code 67 is entered and the power shift
pressure has been fixed by using the above procedure.
1. Enter service code 67. The character display shows the engine speed in rpm.
2. Depress the fine control mode switch (25) in order to shift the blinking position of the character
display to the fourth position from the right.
3. When the boom priority mode switch (23) is depressed, the engine speed increases.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020
XC
h a n g e Pro
Service Information System Page 6 of 6 XChange Pro
F- d F- d
uc
uc
PD
PD
!
!
W
W
t
t
O
O
N
N
y
y
bu
bu
to
to
ww
ww
om
om
k
k
lic
lic
C
C
.c
.c
w
w
tr tr
re
4. When the swing priority mode switch (24) is depressed, the engine speed decreases. The above re
.
.
ac ac
k e r- s o ft w a k e r- s o ft w a
5. When the boom priority mode switch (23) and the power mode switch (19) are depressed
simultaneously, the engine speed rapidly increases.
6. When the swing priority mode switch (24) and the power mode switch (19) are depressed
simultaneously, the engine speed decreases rapidly.
Copyright 1993 - 2020 Caterpillar Inc. Sun Nov 01 2020 16:11:28 GMT-0800 (Pacific Standard Time)
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1:442/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/fulltex... 11/1/2020