Professional Documents
Culture Documents
Product Description: Digital XENSIV Barometric Pressure Sensor
Product Description: Digital XENSIV Barometric Pressure Sensor
Product Description: Digital XENSIV Barometric Pressure Sensor
Product Description
The DPS368 is a miniaturized Digital
Barometric Air Pressure Sensor robust
against water, dust and humidity. It offers a
high accuracy and a low current
consumption, capable of measuring both
pressure and temperature. The pressure
sensor element is based on a capacitive
sensing principle which guarantees high
precision during temperature changes. The
small package makes the DPS368 ideal for
mobile applications and wearable devices.
Due to its robustness it can be used in harsh
environment.
The internal signal processor converts the output from the pressure and temperature sensor elements to 24 bit
results. Each unit is individually calibrated, the calibration coefficients calculated during this process are stored
in the calibration registers. The coefficients are used in the application to convert the measurement results to
high accuracy pressure and temperature values.
The result FIFO can store up to 32 measurement results, allowing for a reduced host processor polling rate.
Sensor measurements and calibration coefficients are available through the serial I²C or SPI interface. The
measurement status is indicated by status bits or interrupts on the SDO pin.
Features
• Pressure sensor with environmentally resistant package
• Operation range: Pressure: 300 –1200 hPa. Temperature: -40 – 85 °C.
• Pressure sensor precision: ± 0.002 hPa (or ±0.02 m) (high precision mode).
• Relative accuracy: ± 0.06 hPa (or ±0.5 m)
• Absolute accuracy: ± 1 hPa (or ±8 m)
• IPx8 certified: Temporary immersion of 50m for 1 hour
• Temperature accuracy: ± 0.5°C.
• Pressure temperature sensitivity: 0.5Pa/K
• Measurement time: Typical 27.6 ms for standard mode (16x). Minimum: 3.6 ms for low precision mode.
• Average current consumption: 1.7 µA for pressure measurement, 1.5 µA for temperature measurement
@1Hz sampling rate, standby: 0.5 µA.
• Supply voltage: VDDIO: 1.2 – 3.6 V, VDD: 1.7 – 3.6 V.
• Operating modes: Command (manual), Background (automatic), and Standby.
• Calibration: Individually calibrated with coefficients for measurement correction.
• FIFO: Stores up to 32 pressure or temperature measurements.
• Interface: I2C and SPI (both with optional interrupt)
• Package dimensions: 8-pin PG-VLGA-8-2 , 2.0 mm x 2.5 mm x 1.1 mm.
• Green Product (RoHS) Compliant
Datasheet Please read the Important Notice and Warnings at the end of this document v1.1
www.infineon.com 2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Typical applications
Typical applications
• Smart watches, wearable & smart phone ( e.g. altitude, fitness tracking, step counting, fall detection)
• Home appliances (e.g. air flow control in HVAC / vacuum cleaner, water level detection, intruder detection)
• Drones ( e.g. flight stability, height control)
• Health care(e.g. fall detection, air flow monitoring, smart inhaler)
Product Validation
Qualified for industrial applications according to the relevant tests of JEDEC47/20/22.
Datasheet 2 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Table of contents
Table of contents
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Definitions, acronyms and abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Pin Configuration and Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Pin Configuration and Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.3 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Temperature Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5 Pressure Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.6 Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Mode transition diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Start-up sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 Measurement Precision and Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Sensor Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6 Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7 Result Register Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8 FIFO Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.9 Calibration and Measurement Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.9.1 How to Calculate Compensated Pressure Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9.2 How to Calculate Compensated Temperature Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9.3 Compensation Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.9.4 Pressure and Temperature calculation flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
5.1 Measurement Settings and Use Case Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Application Circuit Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 IIR filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6 Digital interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Datasheet 3 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Table of contents
Datasheet 4 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Table 1
Term Definition/explanation
Absolute accuracy The absolute measurement accuracy over the entire measurement
range.
Digital bit depth The total bit depth used for conversion of the sensor input to the
digital output. Measured in bits.
Digital resolution The pressure value represented by the LSB change in output. This
value should be much smaller than the sensor noise.
Full Scale Range (FSR) The peak-to-peak measurement range of the sensor.
LSB Least Significant Bit
Measurement time The time required to acquire one sensor output result. This value
determines the maximum measurement rate.
MSB Most Significant Bit
Non-linearity The deviation of measured output from the best-fit straight line,
relative to 1000 hPa and 25 °C.
Output compensation The process of applying an algorithm to the sensor output to improve
the absolute accuracy of the sensor across temperature and to
minimize unit to unit output variation. This algorithm makes use of
both the temperature sensor readings and the individual calibration
coefficients.
Precision (noise) The smallest measurable change, expressed as rms, after sensor
oversampling.
Pressure temperature coefficient The pressure measurement deviation, after compensation, from
expected measurement value due to temperature change from 25 °C.
Measured in Pa/K.
Sensor calibration The process, during the production test, where the sensor's
measurement results are compared against reference values, and a set
of calibration coefficients are calculated from the deviation. The
coefficients are stored in the sensor's memory and are used in the
output compensation.
Sensor oversampling rate (OSR) Specifies the number of sensor measurements used internally to
generate one sensor output result.
Datasheet 5 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Datasheet 6 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
3 Specifications
Figure 2
3 Specifications
3.1 Operating Range
The following operating conditions must not be exceeded in order to ensure correct operation of the device. All
parameters specified in the following sections refer to these operating conditions, unless noted otherwise.
1 Effects of solder drift can be eliminated by one point calibration. See AN487.
Datasheet 7 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
3 Specifications
Attention: Stresses above the values listed as "Absolute Maximum Ratings" may cause permanent damage
to the devices. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Datasheet 8 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
3 Specifications
Datasheet 9 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
3 Specifications
Note: Pressure precision is measured as the average standard deviation. Please refer to the Pressure
Configuration (PRS_CFG) register description for all precision mode options.
Note: The pressure measurement time (and thus the maximum rate) depends on the pressure
measurement precision. Please refer to the Pressure Configuration (PRS_CFG) register description
for an overview of the possible combinations of measurement precision and rate.
Datasheet 10 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
Note: Start-up timing is measured from VDD > 1.2V & VDDIO > 0.6V or Soft Reset.
4 Functional Description
4.1 Operating Modes
The supports 3 different modes of operation: Standby, Command, and Background mode.
• Standby Mode
- Default mode after power on or reset. No measurements are performed.
- All registers and compensation coefficients are accessible.
• Command Mode
- One temperature or pressure measurement is performed according to the selected precision.
- The sensor will return to Standby Mode when the measurement is finished, and the measurement
result will be available in the data registers.
• Background Mode
- Pressure and/or temperature measurements are performed continuously according to the selected
measurement precision and rate. The temperature measurement is performed immediately after the
pressure measurement.
- The FIFO can be used to store 32 measurement results and minimize the number of times the sensor
must be accessed to read out the results.
Note: Operation mode and measurement type are set in the Sensor Operating Mode and Status
(MEAS_CFG) register.
Datasheet 11 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
Datasheet 12 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
In order to achieve a higher precision, the sensor will read multiple times ( oversampling ), and combine the
readings into one result. This increases the current consumption and also the measurement time, reducing the
maximum possible measurement rate. It is necessary to balance the accuracy and data rate required for each
application with the allowable current consumption.
The measurement precision, rate and time is set in the Pressure Configuration (PRS_CFG) and Temperature
Configuration(TMP_CFG) registers. The register descriptions contain information about the current
consumption and the possible combinations of measurement precision, time, and rate.
Enabling temperature measurements allows for compensation of temperature drift in the pressure
measurement. The rates of these measurements can be set independently, but temperature compensation is
more accurate when temperature and pressure measurements are taken together. This reduces the maximum
pressure measurement rate, since: Ratetemperature*Timetemperature + Ratepressure*Timepressure< 1 second.
Measurement Settings and Use Case Examples contains a table with examples of combinations of pressure
and temperature precision and rates for different use cases.
In the figure below is described the Temperature and Pressure measurements sequence in background mode.
4.6 Interrupt
The sensor can generate an interrupt when a new measurement result is available and/or when the FIFO is full.
The sensor uses the SDO pin for the interrupt signal, and interrupt is therefore not supported if the interface is 4-
wire SPI.
The interrupt is enabled and configured in the Interrupt and FIFO configuration (CFG_REG) register. In I2C
configuration the SDO pin serves as both interrupt and as the least significant bit in the device address. If the
SDO pin is pulled low the interrupt polarity must be set to active high and vice-versa.
The interrupt status can be read from the Interrupt Status (INT_STS) register.
Datasheet 13 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
Datasheet 14 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
Steps
1. Read the pressure calibration coefficients (c00, c10, c20, c30, c01, c11, and c21) from the Calibration
Coefficient register.
Note: The coefficients read from the coefficient register are 2's complement numbers.
2. Choose scaling factors kT (for temperature) and kP (for pressure) based on the chosen precision rate. The
scaling factors are listed in Table 9.
3. Read the pressure and temperature result from the registers or FIFO.
Note: The measurements read from the result registers (or FIFO) are 24 bit 2´s complement numbers.
Depending on the chosen measurement rates, the temperature may not have been measured
since the last pressure measurement.
Traw_sc = Traw/kT
Praw_sc = Praw/kP
Steps
1. Read the temperature calibration coefficients ( c0 and c1 ) from the Calibration Coefficients (COEF)
register.
Note: The coefficients read from the coefficient register are 12 bit 2´s complement numbers.
2. Choose scaling factor kT (for temperature) based on the chosen precision rate. The scaling factors are
listed in Table 9.
3. Read the temperature result from the temperature register or FIFO.
Note: The temperature measurements read from the temperature result register (or FIFO) are 24 bit 2
´s complement numbers.
Datasheet 15 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
Traw_sc = Traw/kT
Datasheet 16 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
4 Functional Description
See also How to Calculate Compensated Pressure Values and How to Calculate Compensated Temperature
Values
Datasheet 17 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
5 Applications
5 Applications
5.1 Measurement Settings and Use Case Examples
Datasheet 18 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
5 Applications
Figure 8 Application Circuit Example using the SPI 4-wires serial interface
Figure 9 Application Circuit Example using the SPI 3-wire serial interface
Datasheet 19 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
Figure 10 Application Circuit Example using the SPI 3-wire with interrupt interface
6 Digital interfaces
The measurement data, calibration coefficients, Product ID and configuration registers can be accessed through
both the I2C and SPI serial interfaces.
The SPI interface can configured to operate in 3-wire or 4-wire mode. In I2C and SPI 3-wire, an interrupt output
can be implemented on the SDO pin. The SPI interface support mode '11' only ( CPOL=CPHA='1' ) in 4-wire and
3-wire configuration. The following commands are supported: single byte write, single byte read and multiple
byte read using auto increment from a specified start address. The interface selection is done based on CSB pin
status. If CSB is connected to VDDIO, the I2C interface is active. If CSB is low, the SPI interface is active. After the
CSB has been pulled down once the I2C interface is disabled until the next power-on-reset.
Datasheet 20 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
Datasheet 21 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
A SPI write is carried out by setting CSB low and sending a control byte followed by register data. The control
byte consist of the SPI register address ( full register address without bit 7) and the write command ( bit7 = RW =
'0'). Setting CSB high ends the transaction. The SPI write protocol is described in the diagram below.
A SPI read is initiated by setting CSB low and sending a single control byte. The control byte consist of the SPI
register address ( = full register address without bit 7) and the read command ( bit7 = RW = '1'). After writing the
control byte, data is sent out of the SDO pin ( SDI in 3-wire mode); the register address is automatically
incremented. Sending CSB high ends the SPI read transaction. The SPI read protocol is shown in the diagram
below:
Datasheet 22 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
Datasheet 23 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
Datasheet 24 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Digital interfaces
Datasheet 25 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register Map
7 Register Map
Table 15 Register Map
Register Addr. bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 Reset
Name State
PSR_B2 0x00 PSR[23:16] (r) 00h
PSR_B1 0x01 PSR[15:8](r) 00h
PSR_B0 0x02 PSR[7:0](r) 00h
TMP_B2 0x03 TMP[23:16] (r) 00h
TMP_B1 0x04 TMP[15:8] (r) 00h
TMP_B0 0x05 TMP[7:0] (r) 00h
PRS_CFG 0x06 - PM_RATE [2:0] (rw) PM_PRC [3:0] (rw) 00h
TMP_CFG 0x07 TMP_ TMP_RATE [2:0] (rw) TM_PRC [3:0] (rw) 00h
EXT
(rw)
MEAS_CFG 0x08 COEF_ SENSOR TMP_ PRS_ - MEAS_CRTL [2:0] (rw) C0h
RDY (r) _ RDY (r) RDY (r) RDY (r)
CFG_REG 0x09 INT_ HL INT_ SEL [2:0] (rw) TMP_ PRS_ FIFO_ SPI_ 00h
(rw) SHIFT_ SHIFT_ EN (rw) MODE
EN (rw) EN (rw) (rw)
INT_STS 0x0A - - - - - INT_ INT_ INT_ 00h
FIFO_ TMP(r) PRS(r)
FULL (r)
FIFO_STS 0x0B - - - - - - FIFO_ FIFO_ 00h
FULL(r) EMPTY(r)
RESET 0x0C FIFO_ - - - SOFT_RST [3:0] (w) 00h
FLUSH
(w)
Product ID 0x0D REV_ID [3:0] (r) PROD_ID [3:0] (r) 10h
COEF 0x10- < see register description > XXh
0x21
Reserved 0x22- Reserved XXh
0x27
COEF_SRCE 0x28 TMP_C Reserved XXh
OEF_SR
CE (r)
8 Register description
Datasheet 26 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
8.1.1 PRS_B2
The highest byte of the three bytes measured pressure value.
7 6 5 4 3 2 1 0
8.1.2 PRS_B1
The middle byte of the three bytes measured pressure value.
7 6 5 4 3 2 1 0
Datasheet 27 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
8.1.3 PRS_B0
The lowest byte of the three bytes measured pressure value.
7 6 5 4 3 2 1 0
8.2.1 TMP_B2
The highest byte of the three bytes measured temperature value.
7 6 5 4 3 2 1 0
Datasheet 28 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
8.2.2 TMP_B1
The middle byte of the three bytes measured temperature value.
7 6 5 4 3 2 1 0
8.2.3 TMP_B0
The lowest part of the three bytes measured temperature value.
7 6 5 4 3 2 1 0
Datasheet 29 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
- PM_RATE[2:0] PM_PRC[3:0]
- rw rw
Datasheet 30 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
Table 16 Precision (PaRMS) and pressure measurement time (ms) versus oversampling rate
Oversampling Single 2 times 4 times 8 times 16 times 32 times 64 times 128
(PRC[3:0]) (0000) (0001) (0010) (0011) (0100) (0101) (0110) times
(0111)
Measurement time 3.6 5.2 8.4 14.8 27.6 53.2 104.4 206.8
(ms)
Precision (PaRMS) 2.5 1 0.5 0.4 0.35 0.3 0.2
Datasheet 31 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
Datasheet 32 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
SENSOR_R
COEF_RDY TMP_RDY PRS_RDY - MEAS_CTRL
DY
r r r r - rw
Datasheet 33 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
Datasheet 34 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
INT_FIFO_F
- INT_TMP INT_PRS
ULL
- r r r
Datasheet 35 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
FIFO_EMPT
- FIFO_FULL
Y
- r r
Datasheet 36 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
7 6 5 4 3 2 1 0
FIFO_FLUSH - SOFT_RST
w - w
ID Address: 0DH
Product and revision ID Reset value: 0x10H
7 6 5 4 3 2 1 0
REV_ID PROD_ID
r r
Datasheet 37 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Register description
Note: Generate the decimal numbers out of the calibration coefficients registers data:
Datasheet 38 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Package Dimensions
7 6 5 4 3 2 1 0
TMP_COEF_
-
SRCE
r -
9 Package Dimensions
The sensor package is a 8-pin PG-VLGA-8-2, 2.0 x 2.5 x 1.1 mm3, with 0.65 mm pitch.
Datasheet 39 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Figure 17 DPS368 package drawing ( side view, top view, bottom view)
Datasheet 40 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Datasheet 41 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Note: For further information please consult the 'General recommendation for assembly of Infineon
packages' document which is available on the Infineon Technologies web page
Datasheet 42 v1.1
2019-07-03
DPS368
Digital XENSIVTM barometric pressure sensor
Package Handling
The Infineon pressure sensors can be handled using industry standard pick and place equipment. Care should
be taken to avoid damage to the sensor structure as follows:
• Do not pick the sensor with vacuum tools which make contact with the sensor vent port hole
• The sensor's vent hole should not be exposed to vacuum, this can destroy or damage the MEMS
• Do not blow air into the sensor vent hole. If an air blow cleaning process is used, the vent hole must be
sealed to prevent particle contamination.
• It is recommended to perform the PCB assembly in a clean room environment in order to avoid sensor
contamination.
• Air blow and ultrasonic cleaning procedures shall not be applied to MEMS pressure sensors. A non-clean
paste is recommended for the assembly to avoid subsequent cleaning steps. The MEMS sensor can be
severely damaged by cleaning substances.
• To prevent the blocking or partial blocking of vent hole during PCB assembly, it is recommended to cover
the sound port with protective tape during PCB sawing or system assembly.
• Do not use excessive force to place the sensor on the PCB. The use of industry standard pick and place tools
is recommended in order to limit the mechanical force exerted to the package.
12 Package Handling
Further Information please refer to the attached “Digital Barometric Pressure Sensor_ Package Handling”. It
describes the package handling and delivery format.
Revision history
Document Date of Description of changes
version release
v0.1 05.05.2017 initial release
v0.2 11.29.2017 update package dimensions
v0.3 03.04.2018 Pressure Transfer Function table update
v0.4 19.10.2018 Pressure noise values update
v1.0 01.03.2018 Features and Typical applications chapters update; Package drawing,
Footprint and stencil recommendation, Solder reflow chapters added
v1.1 03.07.2019 Title update
Datasheet 43 v1.1
2019-07-03
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.