Professional Documents
Culture Documents
Hitachi Sb-Zaxis70 06-03 Ks-E379p
Hitachi Sb-Zaxis70 06-03 Ks-E379p
5 kW (55 PS)
Operating Weight :
ZAXIS70 : 6 300 kg
ZAXIS70LC : 6 400 kg
Backhoe Bucket :
PCSA Heaped : 0.13 - 0.33 m³
CECE Heaped : 0.12 - 0.29 m³
F uturistic
P erformance
Easier To Use
(Multi-purpose machine)
• Increased front speed: Swing-independent
3-pumphydraulic system.
• 26% more leveling speed (compared to
EX60-5).
• 4% more travel power (compared to
EX60-5).
• Travel speed increased by 5km/h.
• Three auxiliary ports (valves) as standard
equipment.
&
F aster.
Faster Front Operations (compared to EX60-5)
The arm circuit uses a
new combination of 3 more leveling
pumps to provide not 26% speed
only independent speed
but also increased speed
during leveling opera-
tions as well. (26 % more
horizontal front pulling
speed)
1 670 mm
minimum digging
radius
Increase in maximum
vertical wall depth
210 mm
* Image shown is for expla-
nation purposes only.
Travel Power You Can Depend On Three Auxiliary Ports (Valves) as Standard
A new automatic 2-speed travel motors are used to Equipment
increase travel power and speed. These ports make it easier to use attachments.
more travel power
4% than EX60-5
Travel speeds:
4.8km/h EX60-5 5.0km/h
inimum
M
Operator's compartment
is designed for both
aximum
M Efficiency.
Easy-to-Monitor Instruments
Strategically positioned instru-
ments allow the operator to moni-
tor the status of key areas with
just a glance.
Easy-to-Operate
Switches and other essential
controls are located near the
operator. This helps keep opera-
tor movement to a minimum,
enhancing control and helping to
fight fatigue.
Enhanced visibility on the lower
right side
Auto Control Air Conditioner
(Option)
* Illustration shows a sample of the air flow Simply set the temperature and
during bi-level control. forget about it. Ducts are positio-
ned to promote even air flow
throughout the cab. AM-FM radio as standard
equipment
Safety & Service
Reinforced sections
shown in red
Lock
Unlock
D
& urable.
Smart
Saving
Advanced
technology helps reduce
maintenance costs
Lower running
costs
Cab
Cover for swing
gear lubrication area
Swing motor
Control valve
Water
Fuel tank separator
Outer air
conditioner
filter (option) Oil tank Pilot filter
Air cleaner
Washer tank
Engine
Tool box Pump
1. Flanged pins are used for the boom/arm 3. Bucket joint pins lubricated through bos-
joint sections and the boom foot section ses Servicing Access is at Ground Level to Speed
2. WC thermal spraying for arm joint secti- 4. New HN bushing used for front sections
ons 5. Strengthend arm Daily Inspection
6. Strengthend swing circle
A wide maintenance area helps daily inspection and
repair operations.
New HN Bushing Used
WC (Tungsten Carbide) A special grease groove is used
Thermal Spraying to enhance grease retention
Used at arm end and buc- inside the HN bushing.
ket connection to increase Grease
groove
wear resistance and redu-
Time between lubrication of
ce jerking. bucket components extended to
500 hours
M-shaped seal Grease Lower
roller
Hydraulic Oil Filter Only Needs Replacement
Every 1000 Hours
Link The hydraulic oil filter can be used nearly
twice as long as the previous model, dra-
Shoe
matically reducing maintenance time and
expense.
Longer Track Link Service Life
The M-shaped track link seal is used to enhance grea- 1 000 hours between hydraulic oil filter
replacement
se retention.
Onboard ICX
PC
Information Providing
TSupport.
the data for
Information
Controller echnology making the
right deci-
sions.