Professional Documents
Culture Documents
F. E. (Semester - I) Examination - 2010: Total No. of Questions: 12) (Total No. of Printed Pages: 7
F. E. (Semester - I) Examination - 2010: Total No. of Questions: 12) (Total No. of Printed Pages: 7
of Printed Pages : 7
[3761]-105
F. E. (Semester - I) Examination - 2010
om
ENGINEERING GRAPHICS - I
(June 2008 Pattern)
.c
Instructions :
(1) Answers one question from each unit. Answer three questions
from section - I and three questions from section - II.
id
(2) Answers to the two sections should be drawn on separate
drawing sheet.
(3) Retain all construction lines.
ds
(4) Use of log table, electronic pocket calculator is allowed.
(5) Figure in bracket indicate full marks.
(6) Assume suitable data, if necessary.
(7) Use only half imperial size drawing papers as answer sheets.
pi
SECTION - I
tu
Q.1) (A) Draw an ellipse with the major axis 160 mm and minor axis 120
.s
om
curve. [08]
UNIT - III : ORTHOGRAPHIC PROJECTIONS
Q.3) For the object shown in fig. 1, draw the following views, using
.c
First Angle Method of Projection :
(a) Sectional Elevation in the direction of arrow ‘X’ (section along
A-A) [07]
id
(b) Plan [05]
(c) End View from Right Hand Side [05]
ds
Give all dimensions. [03]
A 36
SIMILAR WED
φ18
ON OTHER SIDE
tu
28
10
10
.s
2HOLES,φ12
20
THROUGH
82
18 18 R1 8
w
36
72 10 R5
w
64 6 20
10
10
w
X R2 A
8
54
Fig. 1
OR
[3761]-105 2 Contd.
Q.4) For the object shown in fig. 2, draw the following views, using First
Angle Method of Projection :
(a) Sectional Elevation looking in the direction of arrow ‘X’
(Section along A-A) [07]
(b) Plan [05]
(c) End View from the Left Hand Side [05]
om
Give all dimensions. [03]
A
90 10
4 R2
0
74 30 2
.c
HO
10 LE
S
φ
0 20
φ4
20
70
id
60 32
φ
4
R1
130
φ2 φ1
0 6
22
44
90
ds
R2
6
0
0
R2
20
Fig. 2
X
pi
Α
UNIT - IV : AUXILIARY PROJECTIONS
Q.5) (A) Fig. 3 shows front view, incomplete side view and partial auxiliary
tu
x
w
45
12 6 6
φ 12
w
o
60
12
R30
15
w
25 60
I EW
6 0 X. V
U OR
. A
I NC
[3761]-105 3 P.T.O.
Q.6) Fig. 4 shows front view, incomplete top view and partial auxiliary
view of an object :
(a) Redraw the given views [05]
(b) Complete the Top View [08]
Show all dimensions. [02]
om
80
20 40 o
FRONT VIEW
20
.c
24
SQ.
id
48 PART. AUXILIARY VIEW
ds
100
Fig. 4
INC. TOP VIEW
pi
SECTION - II
UNIT - V : ISOMETRIC
tu
Q.7) Fig. 5 shows the elevation and end view of an object by First Angle
Method of Projection. Draw an isometric view taking origin at ‘O’
and give all dimensions : [17+3]
28
.s
R22 R30
42
w
54
10
w 76
26
40
22
16
w
O 74
15 30
60 END-VIEW
ELEVATION
Fig. 5
OR
[3761]-105 4 Contd.
Q.8) Fig. 6 shows the elevation and plan of an object by First Angle Method
of projection. Draw its isometric projection taking origin at ‘O’.
Construct isometric scale to read 110 mm length.
Give all dimensions. 25 [15+2+3]
20
om
100
10
20
O
.c
ELEVATION
REGULAR HEXAGON
R35
id
60 o
20
20
12
Fig. 6
O
ds
75
TOP VIEW
70
w
φ75
φ30
w
M16
45
φ60 φ14
15 50
F.V.
A Fig. 7
L.H.S.V.
OR
[3761]-105 5 P.T.O.
Q.10) Fig. 8 shows front view and top view of an object. Draw the
following views by First Angle Method of Projection :
om
(c) Right Hand Side View [08]
.c
φ60
15
φ16
id
10
10
6
10
R12
φ44
ds
20
R15
F.V.
φ16
18
pi
10
16
30
66
A
10
A
tu
18
43 55
Fig. 8
T.V.
.s
[3761]-105 6 Contd.
Q.12) Draw proportionate free hand sketches of the following :
(c) Double V-Butt and Single Bevel Butt Welded joints. [04]
om
.c
id
ds
pi
tu
.s
w
w
w
[3761]-105/7