Professional Documents
Culture Documents
TPG Relays ABB Distance
TPG Relays ABB Distance
TPG Relays ABB Distance
3 Input
AC Voltage V 110-120 rms, phase - phase 100 - 120 rms, phase - phase
AC Current A 1 and 5 (able to accommodate 1A and 5A in one 1 and 5 (able to accommodate 1A and 5A in one device)
device)
Freq Hz 50 50
4 Aux Supply V min 110 Vdc ( -15 s/d +10% ) 48 - 125 Vdc ( 38 - 150 Vdc )
5 Relays Characteristic
Setting Zone - 4 zone (phase - phase / phase ground) 5 Zone ( phase - phase/ phase ground )
Reach Characteristic
Forward Reach Zone ohm 0.1 ohm - 200 ohm 0.005 - 3000 0hm
Reverse Reach Zone ohm 0.1 ohm - 200 ohm 0.005 - 3000 0hm
Zero Sequence Compensation (kn or ohm Used for all zone Yes
Ko)
Angel Characteristic deg Min 48 - 80 deg in 1 step 0 - 90° in step 0.01°
Measuring Accuracy % ± 5% ± 5%
Sensitivity % <10% In 2% In
Maximum Operating time ms <40, at 80% reach setting 30 at 85% reach setting
Tripping Scheme - Single and Three pahse Tripping Single and Three pahse Tripping
Time Setting
Auto Reclose
Synchro Check
Phase Diff deg 5 - 30 deg in 2.5 deg step 5 - 90 deg, step 1 deg
Minimum Features
Continuous A >3 5
MMI - keypad and comm. Port with PC (Built in) keypad and comm. Port with PC (Built in)
Number of record - The last 3 record in ring buffer 100 record in ring buffer
Trigger Analog Signal - Trip signal and analog input change Trip signal and analog input change
Trigger Event Signal - internal and external Trigger internal and external Trigger
Sampling Rate - min 12 ample per cycle min 12 ample per cycle
Recording Duration sec min 2.5 sec 3.4 sec for all input triggerred
7 Communication
8 Performace Test
9 High Voltage Withstand - Min complied with IEC60255-5: Min complied with IEC60255-5:
Dielectric Withstand - 2 kV rms for 1 minute between all 2 kV rms for 1 minute between all
2 kV rms for 1 minute between all 2 kV rms for 1 minute between all
peak, 1.25/50 ps, 0.5 J between all peak, 1.25/50 ps, 0.5 J between all
terminal and terminal to case earth terminal and terminal to case earth
10 Electrical Environment Strength Min complied with IEC60266-11: Min complied with IEC60266-11:
Interruption in the aux supply, in its Interruption in the aux supply, in its
Supply Fast Transient withstand IEC 60255-22-4:1992 1 ANSI C37.90.1 IEC 60255-22-4:1992 1 ANSI C37.90.1
4 kV, 2.5 kHZ Applied Directly to Aux Supply 4 kV, 2.5 kHZ Applied Directly to Aux Supply
4 kV, 2.5 kHZ Applied Directly to Input 4 kV, 2.5 kHZ Applied Directly to Input
Radio interference withstand IEC 60255-22-3:1992/ANSI C37.90.2 IEC 60255-22-3/ANSI C37.90.2 : 2004
25Mhz - 1000Mhz, zero and 100% sq wave 80Mhz - 1000Mhz, zero and 100% sq wave
Modulated Modulated
4kV fast transient and 2.5 kV oscilatory app. 4kV fast transient and 2.5 kV oscilatory app.
directly across each output contact, optically directly across each output contact, optically
isolated input and power supply circuit isolated input and power supply circuit
Operation Temp 10 - 50 deg C ( IEC 60255-6:1988 -25 to 55 deg C) 10 - 50 deg C ( IEC 60255-6:1988 -25 to 55 deg C)
and +40 deg C) IEC 60529:1989 and +40 deg C) IEC 60529:1989
IP 52 Protection ( front panel ) againts dust IP 52 Protection ( front panel ) againts dust
and dripping water at 15deg vertical and dripping water at 15deg vertical
12 Mechanical Strength Minimum Complied with Minimum Complied with
Range Setting
Teleprotection Scheme Basic, Blocking and POTT Basic, Blocking and POTT