Professional Documents
Culture Documents
Lawson - Desk: Assembly Instructions - 402/4439 412/3392 412/6416
Lawson - Desk: Assembly Instructions - 402/4439 412/3392 412/6416
Dimensions
Width - 100cm
Depth - 39.5cm
MADE IN
Height - 73.5cm
BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 17/04/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs • Make sure you have enough • We do not
approximately 20kgs. space to layout the parts before recommend the
Please lift with care. starting. use of power
drill/drivers for
• Check you have all the • Do not stand or put weight on inserting screws,
components and tools listed on the product, this could cause as this could damage the unit.
pages 2 and 3. damage. Only use hand screwdrivers.
• Remove all fittings from the • Assemble the item as close to • Safety note: If there is any
plastic bags and separate them its final position (in the same chance of this unit being pulled
into their groups. room) as possible. over by children etc. it is
recommended that the unit is
• Keep children and animals • Assemble on a soft level secured to a wall using suitable
away from the work area, small surface to avoid damaging the fixings (not supplied).
parts could choke if swallowed. unit or your floor (use opened
out unit carton). • Dispose of all packaging
• Parts of the assembly will be carefully and responsibly.
easier with 2 people.
• Only clean using a damp cloth • From time to time check that • This product should not be
and mild detergent, do no use there are no loose screws on discarded with household
bleach or abrasive cleaners. this unit. waste. Take to your local
authority waste disposal centre.
7 Modesty (DF2772)
(620 x 157mm)
8 Door (DF2771)
(326 x 321mm)
9 Back (X707-353)
(707 x 353mm)
2
If you have damaged or missing components, call the
Components - Fittings Customer Helpline: 03456 400800 quoting the reference
numbers below
A B C
D E F
G H I
Hinge plate
Plastic Nail (F91) x 6 (F523) x 2
Hinge (F522) x 2
Handle (F236) x 1
Tools required
Spirit
level Square
Eye protection
Cross-head Scissors Hammer (when using a
Rule screwdriver hammer or drill) Bradawl
3
If you have damaged or missing components, call the
Assembly Instructions Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
Prepare the upright A
B
A B
Screw 4 metal dowels A A A
into the upright 2 .
A
Note: Tighten the metal
dowels up fully against 2
the panels.
Finished
Insert 2 large locking front edge
nuts B into the upright
.2 .
Step 2 B
B B
Prepare the 2 base
panels B B
Finished
front edge
4
Assembly Instructions
Step 3
A
Fit a base to the
upright
B
Push a base 5 onto the
upright 2 . 2
5
Use a screwdriver to
tighten the 2 large
locking nuts B fitted to
the upright 2 .
Finished Finished
Note: Turn the large front edge front edge
locking nuts B as far as
they will go - more than
1/2 a turn.
Step 4
Fit the other base to
the upright
2
Push the base 5 onto
the upright 2 .
Use a screwdriver to 5
tighten the 2 large
locking nuts B fitted to
the upright 2 .
Finished
front edge
Step 5
Prepare the left end Finished
front edge
Screw 4 metal dowels A A
into the left end 1 . H A B
A
Insert 2 large locking B
A
nuts B into the left end H
K
.1 .
H
Fit 2 hinge plates H onto
1
the left end 1 , making
sure that the slot is
facing towards the
finished front edge.
5
Assembly Instructions
Step 6
Fit the left end
Step 7 B
B
Prepare the modesty Finished
top edge
Insert 4 large locking B
B
nuts B into the modesty
.7 . 7
A
Step 8 A B
6
Assembly Instructions
Step 9 Finished
top edge
Fit the modesty
Use a screwdriver to 2
tighten the 2 large
locking nuts B fitted to
the modesty 7 .
Step 10
Fit the right end
Use a screwdriver to 3
tighten the 2 large
locking nuts B fitted to
the modesty 7 .
Finished
front edge
Step 11 A
A
Prepare the top
A
Screw 6 metal dowels A
into the top 4 . A
A
4 A
Finished
front edge
7
Assembly Instructions
Step 12
Fit the ltop
4
Push the top 4 onto
the assembly.
3
Use a screwdriver to 2
tighten the 6 large
locking nuts B fitted to
left end 1 , upright 2
and right end 3 .
1
Step 13
Fit the back
a: The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b:
b: Place the back 9 F
onto the unit.
x
Nail F around the
outside edges of the y
back 9 .
9
8
Assembly Instructions
Step 14
Fit the 6 plastic nails
Step 15
Fit 4 shelf studs
C x4
Step 16
Fit the shelf
Finished
front edge
9
Assembly Instructions
Step 17
Fit the door stop
Step 18
E
Prepare the door E
E
E
Push fit 2 hinges I into
the door 8 .
10
Assembly Instructions
Step 19
a: H
H b: H
e: Attach a handle J to
the door 8 using 2
screws D .
11
Assembly Instructions
Step 20
Adjust the door if
needed a:
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, front-
to-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
b:
make the unit level
A
BEFORE making any
adjustment to the hinges,
as shown.
A
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
c:
Retighten screw A.
B
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d:
d: Sideways
adjustment.
To move door ‘out’ C
loosen screw C.
To move door ‘in’ tighten
screw C.
12
Assembly Instructions
Step 21
Assembly is complete
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
13
ALR3189