Professional Documents
Culture Documents
Layer 3 Message Dictionary - A Interface PDF
Layer 3 Message Dictionary - A Interface PDF
Layer 3 Message Dictionary - A Interface PDF
This document is a working document and subject to change. It is invited that all comments are
passed to the author for inclusion in future iterations.
DISTRIBUTION
APPROVAL
NAME
FUNCTION
SIGNATURE
Ed 04
3BK 11202 0075 DSZZA
3
0. DOCUMENT HISTORY
Release 1 TLA/100
Release 2 S/P2/3.4.2.1
Ed 04
3BK 11202 0075 DSZZA
4
Table of Contents
0. DOCUMENT HISTORY................................................................................................................ 3
1. REFERENCES ............................................................................................................................. 6
1.1. GSM REFERENCES .................................................................................................................. 6
1.2. TLA REFERENCE LIST FROM THE BSS DOCTREE................................................................. 6
2. GENERAL PRESENTATION....................................................................................................... 7
2.1. PRELIMINARIES ........................................................................................................................ 7
2.2. MESSAGES PRESENTATION................................................................................................... 7
2.2.1. Introduction......................................................................................................................... 7
2.2.2. The General Overview......................................................................................................... 8
2.3. THE INFORMATION ELEMENT DESCRIPTION....................................................................... 9
2.3.1. THE BIT DESCRIPTION ..................................................................................................... 9
2.4. SUMMARY DESCRIPTION........................................................................................................10
2.5. CROSS REFERENCE ...............................................................................................................10
3. LIST OF THE MESSAGES........................................................................................................ 11
Ed 04
3BK 11202 0075 DSZZA
5
Ed 04
3BK 11202 0075 DSZZA
6
1. REFERENCES
Ed 04
3BK 11202 0075 DSZZA
7
2. GENERAL PRESENTATION
2.1. PRELIMINARIES
This volume of the message dictionary details the non-transparent messages handled by
the Alcatel BSS over the A interface.
As for this release both GSM phase 1 and phase 2 formats are supported, this document
shows both message formats where applicable.
- A general overview,
- A detailed description of the Information Elements,
- A bit description.
- A cross reference of all the Information Elements. This allows to find all the messages
in which one Information Element appears.
2.2.1. Introduction
All the messages are organised alphabetically under the relevant interface. Three
parts are given for each messages :
- a general overview :
It is a general description of the message including the Information Elements list, the
maximum and minimum lengths in octets, the normal and abnormal following
events.
It is mainly the use of the Information Element within the BSS entities.
- A Bit Description :
Ed 04
3BK 11202 0075 DSZZA
8
NAME field :
The name of the message.
INTERFACE field :
The list of three Interfaces
CHANNEL/USAGE field :
According to the involved interface, it is the radio channel definition or the fact that
the message is transparent or not for the BTS. When the box is empty, the message
is not used on this interface.
GSM-REF. field :
It is the reference to a GSM TS
FUNCTION field :
It is the description of the function of the message. This is extracted from the GSM
TSs.
DIRECTION field :
It is the direction of the message from one entity of the BSS or MS to another one.
TIMER field :
It is the name of the Timers (started or stopped) associated with the message.
Ed 04
3BK 11202 0075 DSZZA
9
TYPE field :
DEFINITION Field :
It is an extract of GSM TS giving the usage of the Information Element.
Ed 04
3BK 11202 0075 DSZZA
10
On each interface, a specific header is used and is described with the list of messages for
each interface.
Ed 04
3BK 11202 0075 DSZZA
11
A
ASSIGNMENT COMPLETE
ASSIGNMENT FAILURE
ASSIGNMENT REQUEST
B
BLOCK
BLOCKING ACKNOWLEDGE
BSS INVOKE TRACE
C
CIPHER MODE COMMAND
CIPHER MODE COMPLETE
CIPHER MODE REJECT
CIRCUIT GROUP BLOCK not used
CIRCUIT GROUP BLOCKING ACKNOWLEDGE not used
CIRCUIT GROUP UNBLOCK not used
CIRCUIT GROUP UNBLOCKING ACKNOWLEDGE not used
CLASSMARK REQUEST
CLASSMARK UPDATE
CLEAR COMMAND
CLEAR COMPLETE
CLEAR REQUEST
COMPLETE LAYER 3 INFORMATION
CONFUSION not used
H
HANDOVER CANDIDATE ENQUIRE not used
HANDOVER CANDIDATE RESPONSE not used
HANDOVER COMMAND
HANDOVER COMPLETE
HANDOVER DETECT
HANDOVER FAILURE
HANDOVER PERFORMED
HANDOVER REQUEST
HANDOVER REQUEST ACKNOWLEDGE
HANDOVER REQUIRED
HANDOVER REQUIRED REJECT
L
LOAD INDICATION not used
M
MSC INVOKE TRACE
O
OVERLOAD
P
PAGING
Ed 04
3BK 11202 0075 DSZZA
12
Q
QUEUING INDICATION
R
RESET
RESET ACKNOWLEDGE
RESET CIRCUIT
RESET CIRCUIT ACKNOWLEDGE
RESOURCE INDICATION not used
RESOURCE REQUEST not used
RESUME not used
S
SAPI "n" CLEAR COMMAND
SAPI "n" CLEAR COMPLETE not used
SAPI "n" REJECT
SUSPEND not used
T
TRACE INVOCATION
U
UNBLOCK
UNBLOCKING ACKNOWLEDGE
UNEQUIPPED CIRCUIT
Ed 04
3BK 11202 0075 DSZZA
13
C
Cause
ASSIGNMENT FAILURE
BLOCK
CIPHER MODE REJECT (phase 2 message)
CLEAR COMMAND
CLEAR REQUEST
HANDOVER FAILURE
HANDOVER PERFORMED
HANDOVER REQUEST (phase 2 only)
HANDOVER REQUIRED
HANDOVER REQUIRED REJECT
OVERLOAD
RESET
RESET CIRCUIT
SAPI "n" REJECT
Cell Identifier
ASSIGNMENT COMPLETE
COMPLETE LAYER 3 INFORMATION
HANDOVER COMMAND
HANDOVER PERFORMED
HANDOVER REQUEST
OVERLOAD
HANDOVER REQUIRED
PAGING
PAGING
Channel Type
ASSIGNMENT REQUEST
HANDOVER REQUEST
ASSIGNMENT COMPLETE
HANDOVER REQUEST ACKNOWLEDGE
HANDOVER PERFORMED
COMPLETE LAYER 3 INFORMATION
Ed 04
3BK 11202 0075 DSZZA
14
ASSIGNMENT COMPLETE
CIPHER MODE COMPLETE
HANDOVER REQUEST ACKNOWLEDGE
HANDOVER PERFORMED
ASSIGNMENT REQUEST
BLOCK
BLOCKING ACKNOWLEDGE
HANDOVER REQUEST
RESET CIRCUIT
RESET CIRCUIT ACKNOWLEDGE
UNBLOCK
UNBLOCKING ACKNOWLEDGE
UNEQUIPPED CIRCUIT (phase 2 message)
ASSIGNMENT COMPLETE
ASSIGNMENT FAILURE
HANDOVER FAILURE
HANDOVER REQUEST ACKNOWLEDGE
ASSIGNMENT FAILURE
HANDOVER FAILURE
HANDOVER REQUIRED
HANDOVER REQUEST
Ed 04
3BK 11202 0075 DSZZA
15
CLASSMARK UPDATE
HANDOVER REQUEST
HANDOVER REQUEST
HANDOVER REQUIRED
HANDOVER REQUIRED
D
DLCI
SAPI "n" REJECT
ASSIGNMENT REQUEST
HANDOVER REQUEST
E
Encryption Information
HANDOVER REQUIRED
F
Forward Indicator
I
IMSI
PAGING
ASSIGNMENT REQUEST
HANDOVER REQUEST
Ed 04
3BK 11202 0075 DSZZA
16
L
Layer 3 Header Information
ASSIGNMENT REQUEST
CIPHER MODE COMMAND
CLEAR COMMAND
Layer 3 Information
M
Mobile Identity
O
OMCId
P
Priority
ASSIGNMENT REQUEST
HANDOVER REQUEST
Ed 04
3BK 11202 0075 DSZZA
17
Q
Queuing Indicator (phase 2 IE)
HANDOVER REQUIRED
R
Radio Channel Identity (phase 1 IE)
ASSIGNMENT COMPLETE
ASSIGNMENT REQUEST
HANDOVER PERFORMED
HANDOVER REQUEST
Response Request
HANDOVER REQUIRED
RR Cause
ASSIGNMENT COMPLETE
ASSIGNMENT FAILURE
HANDOVER COMPLETE
HANDOVER FAILURE
S
Speech version
ASSIGNMENT COMPLETE
HANDOVER REQUEST
HANDOVER REQUEST ACK
HANDOVER REQUIRED
HANDOVER PERFORMED
T
TMSI
PAGING
Trace Reference
Ed 04
3BK 11202 0075 DSZZA
18
Trace Type
TransactionId
TriggerId
Ed 04
3BK 11202 0075 DSZZA
19
Message type uniquely identifies the message being sent. It is a single octet element,
mandatory in all messages.
8 7 6 5 4 3 2 1
E Message type
8 7 6 5 4 3 2 1 Hex
0 0 0 0 0 0 0 0 Reserved
ASSIGNMENT MESSAGES
0 0 0 0 0 0 0 1 01 - Assignment Request
0 0 0 0 0 0 1 0 02 - Assignment Complete
0 0 0 0 0 0 1 1 03 - Assignment Failure
HANDOVER MESSAGES
0 0 0 1 0 0 0 0 10 - Handover Request
0 0 0 1 0 0 0 1 11 - Handover Required
0 0 0 1 0 0 1 0 12 - Handover Request Acknowledge
0 0 0 1 0 0 1 1 13 - Handover Command
0 0 0 1 0 1 0 0 14 - Handover Complete
0 0 0 1 0 1 1 0 16 - Handover Failure
0 0 0 1 0 1 1 1 17 - Handover Performed
0 0 0 1 1 0 0 0 18 - Handover Candidate Enquire
0 0 0 1 1 0 0 1 19 - Handover Candidate Response
0 0 0 1 1 0 1 0 1A - Handover Required Reject
0 0 0 1 1 0 1 1 1B - Handover Detect
Ed 04
3BK 11202 0075 DSZZA
20
8 7 6 5 4 3 2 1 Hex
RELEASE MESSAGES
0 0 1 0 0 0 0 0 20 - Clear Command
0 0 1 0 0 0 0 1 21 - Clear Complete
0 0 1 0 0 0 1 0 22 - Clear Request
0 0 1 0 0 0 1 1 23 - SAPI "n" Clear Command (phase 1 only)
0 0 1 0 0 1 0 1 25 - SAPI "n" Reject
0 0 1 0 0 1 1 0 26 - Confusion
GENERAL MESSAGES
0 0 1 1 0 0 0 0 30 - Reset
0 0 1 1 0 0 0 1 31 - Reset Acknowledge
0 0 1 1 0 0 1 0 32 - Overload
0 0 1 1 0 0 1 1 33 - Trace Invocation (phase 1 only)
0 0 1 1 0 1 0 0 34 - Reset Circuit
0 0 1 1 0 1 0 1 35 - Reset Circuit Acknowledge
0 0 1 1 0 1 1 0 36 - MSC invoke trace
0 0 1 1 0 1 1 1 37 - BSC invoke trace
0 1 0 0 0 0 0 0 40 - Block
0 1 0 0 0 0 0 1 41 - Blocking Acknowledge
0 1 0 0 0 0 1 0 42 - Unblock
0 1 0 0 0 0 1 1 43 - Unblocking Acknowledge
0 1 0 0 0 1 0 0 44 - Circuit group block
0 1 0 0 0 1 0 1 45 - Circuit group blocking acknowledge
0 1 0 0 0 1 1 0 46 - Circuit group unblock
0 1 0 0 0 1 1 1 47 - Circuit group unblocking acknowledge
0 1 0 0 1 0 0 0 48 - Unequipped circuit
0 1 0 1 0 0 0 0 50 - Resource Request
0 1 0 1 0 0 0 1 51 - Resource Indication
0 1 0 1 0 0 1 0 52 - Paging
0 1 0 1 0 0 1 1 53 - Cipher Mode Command
0 1 0 1 0 1 0 0 54 - Classmark Update
0 1 0 1 0 1 0 1 55 - Cipher Mode Complete
0 1 0 1 0 1 1 0 56 - Queuing Indication
0 1 0 1 0 1 1 1 57 - Complete Layer 3 Information
0 1 0 1 1 0 0 0 58 - Classmark Request
0 1 0 1 1 0 0 1 59 - Cipher mode reject
Ed 04
3BK 11202 0075 DSZZA
21
Ed 04
3BK 11202 0075 DSZZA
22
ASSIGNMENT COMPLETE
NAME ASSIGNMENT COMPLETE -- A Interface
This message is sent from BSC to MSC and indicates that the requested
FUNCTION assignment has been completed correctly.
FOLLOWING
EVENT Procedure to be continued on Message replaced by assign T3107
allocated channel. failure
SPECIF.
DOC. REF. Normal Assignment Procedure (ref. [3])
Internal Handover (ref. [6])
In Call Modification (ref. [8])
Internal Directed Retry (ref. [26])
DEFINITION
This element is passed from the air interface to the MSC transparently, when
received from the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 1
RR Cause
RR Cause : the same value received (and same meaning) as the Assignment Complete on
the Air Interface.
The RR Cause information, received from MS (in the "assignment complete" message), has
been stored, and is given to the MSC.
DEFINITION
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0: Discriminator 1:
MCC, MNC
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 1 0
RR 0 0 0 1 0 1 0 1
Cause RR Cause optional
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont.
ASSIGNMENT FAILURE
NAME ASSIGNMENT FAILURE -- A Interface
FOLLOWING
EVENT MSC decides to cancel the
procedure or to reallocate a
new channel.
SPECIF.
DOC. REF. Normal Assignment Procedure (ref. [3])
Internal Handover (ref. [6])
In call modification (ref. [8])
Internal Directed Retry (ref. [26])
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
(*) In case of discrepancy for cause value usage between this document and 08.08
application document, 08.08 application document shall prevail (see ref. [24] in ref. list).
DEFINITION
This element is passed from the air interface to the MSC transparently, when
received from the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 1
RR Cause
RR Cause same value (and same meaning) as Assignment Failure on the Air Interface.
The RR Cause information, received from MS (in the "assignment failure" message), has
been stored, and is given to the MSC.
This element is optional because the BSC may send the "assignment failure" message
without having received the same message from the MS.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 1 1
0 0 0 0 0 1 0 0
CAUSE Length (value = 1)
0 Cause value
RR 0 0 0 1 0 1 0 1
CAUSE RR Cause optional
ASSIGNMENT REQUEST
NAME ASSIGNMENT REQUEST
FUNCTION Used by the MSC to the BSC in order to request the BSS to assign radio
resource or to change the mode, the attributes of which are defined
within the message.
FOLLOWING
EVENT Assignment command sent to Assignment failure sent to the
the MS after the Channel MSC
Allocation T 3107
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
32
DEFINITION
This element contains all of the information that the BSC requires to determine the
radio resource that is required.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 1 1
Length 2
spare Speech or data indicator 3
Channel Rate and type 4
For values 0001 and 0010 a dedicated terrestrial resource is also required.
0000 1000 Full rate TCH channel Bm. Preference between permitted speech versions or
full rate TCH as indicated in octet 5, 5a ...
0000 1001 Half rate TCH channel Lm. Preference between permitted speech versions or
half rate TCH as indicated in octet 5, 5a ...
0000 1010 Full or Half rate TCH channel, Full rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1011 Full or Half rate TCH channel, Half rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1111 Full or Half rate TCH channel, changes allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0001 1010 Full or Half rate TCH channel, Full rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1011 Full or Half rate TCH channel. Half rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1111 Full or Half rate TCH channel, changes not allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0000 0000 SDCCH or Full rate TCH channel Bm or Half rate TCH channel Lm
0000 0001 SDCCH
0000 0010 SDCCH or Full rate TCH channel Bm Not
supported
0000 0011 SDCCH or Half rate TCH channel Lm Not
supported
0000 1000 Full rate TCH channel Bm Not supported
0000 1001 Half rate TCH channel Lm Not supported
0000 1010 Full or Half rate TCH, FR preferred, changes allowed Not supported
0000 1011 Full or Half rate TCH, HR preferred, changes allowed Not supported
0001 1010 Full or Half rate TCH, FR preferred, changes not allowed Not supported
0001 1011 Full or Half rate TCH, HR preferred, changes not allowed Not supported
All other values are reserved.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
34
765 4321
000 0001 GSM speech full rate version 1
001 0001 GSM speech full rate version 2
010 0001 GSM speech full rate version 3 not supported
000 0101 GSM speech half rate version 1
001 0101 GSM speech half rate version 2 not supported
010 0101 GSM speech half rate version 3 not supported
Ext : reserved for extension, set to value 0 (= no extension) for this message.
For non-transparent service bits 6-1 indicate the radio interface data rate;
65 4321
00 0000 12 kbits/s for TCH FR
6 kbits/s for TCH HR Not supported
01 0000 12 kbits/s
01 0001 6 kbits/s Not supported
Stored in order to be able to allocate the required channel. Use for the sending of the
"Channel Activation" message to the BTS and the "Assignment Command" message to the
MS.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
35
DEFINITION
This element is used to supply the BSS with information that needs to be included in
the header of layer 3 messages over the radio interface.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 1
Length (value = 2)
0 0 0 0 Protocol Discriminator
0 0 0 0 Transaction Identifier
GSM states that this IE has no useful purpose. Thus contents of this information element
will be ignored by the BSC.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
36
DEFINITION
Definition of the priority of the request for traffic channels only.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 0
Length
spare Priority level qa pe
Priority level
6543
0000 spare
0001 priority level 1 = highest priority
0010 priority level 2 = second highest priority
:
1110 Priority level 14 = lowest priority
1111 priority not used
if queing is allowed (qa =1) and priority =1111 then lowest priority is assigned.
if queing is allowed (qa =1) and priority =0000 then lowest priority is assigned.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
37
DEFINITION
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (highpart)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
Stored for further usage (to control if terrestrial channel is already in use).
In case of Signalling Channel type, the BSC reacts at the reception of this parameter with
an ASSIGNMENT FAILURE (cause protocol error).
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
38
DEFINITION
This flag indicates if the DTX function in the BSS is to be disabled on a particular
radio channel.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 1
0 0 0 0 0 0 0 DTX
Flag
- In case of speech (full rate only), the DTX is sent to the BTS in the "CHANNEL
ACTIVATION" message.
- For Speech channel (full rate only), if not included, "DTX enabled" in downlink direction is
selected as default value.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
39
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
0 0 0 0 1 0 1 1
Length (value=3)
Channel spare Speech or data indicator
Type Channel Rate and type
0 0 0 0 0 1 1 1
Layer 3 Length (value=2)
Header 0 0 0 0 Proto. Discrim
Information 0 0 0 0 Transac. Identifier
0 0 0 0 0 1 1 0
Priority Length (value=1) Optional
Spare Priority Level qa pe
Circuit 0 0 0 0 0 0 0 1
Identity PCM Multiplex in use (high part) Optional
Code Low part TS in use
Downlink DTX 0 0 0 1 1 0 0 1 Optional
Flag 0 0 0 0 0 0 0 DTX
Flag
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
40
BLOCK
NAME BLOCK
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message is sent from the BSS to the MSC to indicate that a
particular terrestrial resource must be blocked at the MSC and cannot
therefore be used for traffic.
FOLLOWING
EVENT T1
Blocking Acknowledge short or
long
SPECIF Reset Circuit and Blocking and unequipped circuit (ref. [22])
DOC. REF.
Ed 04 BLOCK
3BK 11202 0075 DSZZA
41
DEFINITION
Defines the terrestrial channel
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
This parameter is given to the MSC in order to report a failure on a specific terrestrial
channel.
Ed 04 BLOCK
3BK 11202 0075 DSZZA
42
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause Value
Used causes
010 0010 Requested terrestrial resource unavailable
000 0111 0 and M intervention
Ed 04 BLOCK
3BK 11202 0075 DSZZA
43
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0
Circuit 0 0 0 0 0 0 0 1
Identity PCM Multiplex in use (high part)
Code Low part TS in use
0 0 0 0 0 1 0 0
Cause Length=1
0 Cause Value
Ed 04 BLOCK
3BK 11202 0075 DSZZA
44
BLOCKING ACKNOWLEDGE
NAME BLOCKING ACKNOWLEDGE
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message is sent from the MSC to the BSS to acknowledge the
receipt of an earlier block message and to indicate that the circuit
concerned has been removed from service.
FOLLOWING
EVENT
Timer 1 is stopped upon T 1 short
reception of this message. or long
SPECIF Reset Circuit and Blocking and unequipped circuit (ref. [22])
DOC. REF.
Ed 04 BLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
45
DEFINITION
Defines the terrestrial channel
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (highpart)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
This parameter is given to the BSC in order to recognise this message from a previous
block message.
Ed 04 BLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
46
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 1
Circuit 0 0 0 0 0 0 0 1
Identity PCM Multiplex in use (high part)
Code Low part TS in use
Ed 04 BLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
47
FUNCTION This message is sent from MSC to BSC via the relevant SCCP
connection associated with that MS transaction. It updates the encryption
parameters for the concerned MS.
INFORMATIO
N Header MF 1
ELEMENT Layer 3 header Information MF 4
LIST Encryption Information MV 3-11
FOLLOWING
EVENT Next valid frame which may
be the "ciphering mode
complete" -
DEFINITION
This element is used to supply the BSS with information that needs to be included in
the header of layer 3 messages over the radio interface.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
1 0 0 0 0 0 1 1 1
2 Length = 2
3 0 0 0 0 Protocol
Discriminator
4 0 0 0 0 Transaction
Identifier
Protocol Discriminator and Transaction Identifier are used in order to have information for
the sending of the "Ciphering Mode Command" message to the MS.
Refer to the general part at the beginning of this dictionary.
DEFINITION
This element contains the user data encryption information used to control any
encryption equipment at the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted Algorithms
Key
: :
: :
Key (continued)
Algorithm Identifier
The permitted algorithms octet is a bit map indicating the encryption algorithms from which
the BSS may select the algorithm to be used.
Bit No
1 No encryption
2 GSM A5/1
3 GSM A5/2
4 GSM A5/3 Not supported
5 GSM A5/4 Not supported
6 GSM A5/5 Not supported
7 GSM A5/6 Not supported
8 GSM A5/7 Not supported
A bit position encoded as 1 indicates that the BSS may use the encryption algorithm
repesented by that bit position. A bit position encoded as 0 indicates that the BSS shall not
use the encryption algorithm represented by that bit position. A permitted algorithms octet
containing all bits encoded as 0 shall not be used.
The key shall be present if at least one of the A5 encryption algorithms is permitted. When
present, the MSC will send a key which shall be 8 octets long.
Stored at the BSC in order to be able to give the information to the BTS (during internal
Handover for example, or when the BSC allocates a TCH).
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 0 1 1
0 0 0 0 0 1 1 1
Layer 3 Length (value = 2)
Header 0 0 0 0 Protocol
Discriminator
Information 0 0 0 0 Transaction
Identifier
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted Algorithms
Encryption Key
Information : :
: :
Key (continued)
FUNCTION This message sent from BSC to MSC indicates that a successful cipher
synchronisation has been achieved across the Air Interface.
FOLLOWING
EVENT
- - -
This message is only sent to the MSC if the message CIPHERING MODE COMPLETE is
received from the MS.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 1
CLASSMARK UPDATE
NAME CLASSMARK UPDATE
FUNCTION This message is sent by the BSC to the MSC to report a change of
Classmark in the Mobile Station.
FOLLOWING
EVENT -
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
55
DEFINITION :
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction as given by a MS supporting GSM phase 1.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
Revision Encryption RF power 3
level Algorithm Capability
0 0 0 0 SM. Frequency capability 4
cap
Octet 3
Bits 8 7 6
Revision level : 0 0 0 Reserved for phase 1.
All other values reserved
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
56
Octet 4
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 321
FC Frequency Capability : 0 0 0 Band no 0
Other valuse reserved.
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
57
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
0 Revision 0 A5/1 RF power 3
spare level spare Capability
0 PS SS Screen. SM. 0 0 FC 4
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2 5
spare spare spare spare spare
Octet 3
Bits 76
Revision level : 00 Reserved for phase 1.
01 Used by phase 2 mobiles
All other values reserved
Bit 4
A5/1 : 0 algorithm A5/1 available
1 algorithm A5/1 not available.
Bits 321
RF Power capability :
GSM900 000 class 1
001 class 2
010 class 3
011 class 4
100 class 5
All other values reserved
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
58
Bits 65
SS Screening Indicator : 00
01
10
11
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 1
FC Frequency Capability : GSM900
0 The MS does not support the extension band
G1 in addition to the primary GSM band.
1 The MS does support the extension band G1.
DCS1800
0 Reserved for future use
Octet 5
Bit 8
CM3 Classmark 3 0 No additional MS capability
1 Additional MS capabilities are described in the
classmark 3 information element.
Bit 2
A5/3 algorithm supported 0 A5/3 not available
1 A5/3 available
Bit 1
A5/2 algorithm supported 0 A5/2 not available
1 A5/2 available
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
59
The BSC takes this information in order to have the MS power capability for the power
control and algorithm information. Default values are used for 'revision level', 'RF Power
Capability' and MS cipher capability if the BSC can not decode these fields (see reference
[25]).
Additional mobile info can be obtained by invoking the classmark interrogation procedure.
Note: The BSC may remove the octet 5 of this IE according to the O&M parameter
STRIP_O5_CM2
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
60
GENERAL DESCRIPTION
GSM phase 1 MS
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 0
0 0 0 1 0 0 1 0
Classmark Length (value = 2)
Information Revision Encryption RF Power
Type 2 Level Algorithm Capability
0 0 0 0 SM Frequency
CAP. Capability
GSM phase 2 MS
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 0
0 0 0 1 0 0 1 0
Length = 3
Classmark 0 Revision 0 A5/1 RF power
spare level spare Capability
Information 0 PS SS Screen. SM. 0 0 FC
Type 2 spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2
spare spare spare spare spare
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
61
CLEAR COMMAND
NAME CLEAR COMMAND
FUNCTION This message is sent from MSC to BSC to instruct the BSS to release
the associated dedicated resource.
INFORMATIO
N Header MF 1
ELEMENT Layer 3 header Information MF 4
LIST Cause MF 3
FOLLOWING
EVENT
Channel Release to MS - -
Ed 04 CLEAR COMMAND
3BK 11202 0075 DSZZA
62
DEFINITION
This element is used to supply the BSS with information that needs to be included in
the header of layer 3 messages over the radio interface.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
1 0 0 0 0 0 1 1 1
2 Length = 2
3 0 0 0 0 Protocol
Discriminator
4 0 0 0 0 Transaction
Identifier
Ed 04 CLEAR COMMAND
3BK 11202 0075 DSZZA
63
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
If other cause values are received, the BSC should react in a normal way. i.e. If the cause
value is incorrect or missing, clearing is still performed.
The MSC gives to the BSC some indication on the event (normal or not) which is the cause
of the release. This may be sent to the MS in the "Channel Release" message (RR Cause
field).
Ed 04 CLEAR COMMAND
3BK 11202 0075 DSZZA
64
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 0
0 0 0 0 0 1 1 1
Layer 3 Length (value = 2)
Header 0 0 0 0 Protocol
Discriminator
Information 0 0 0 0 Transaction
Identifier
0 0 0 0 0 1 0 0
Cause Length (value = 1)
0 Cause value
Ed 04 CLEAR COMMAND
3BK 11202 0075 DSZZA
65
CLEAR COMPLETE
NAME CLEAR COMPLETE
FUNCTION This message is sent from the BSC to the MSC to inform the MSC that
the associated dedicated resource has been successfully cleared
SPECIF
DOC. REF. Call Release (ref. [5])
Radio Link Establishment (ref. [2])
Ed 04 CLEAR COMPLETE
3BK 11202 0075 DSZZA
66
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 1
Ed 04 CLEAR COMPLETE
3BK 11202 0075 DSZZA
67
CLEAR REQUEST
NAME CLEAR REQUEST
FUNCTION This message is sent from the BSC to the MSC to indicate to the MSC
that the BSS wishes to release the associated connection
FOLLOWING
EVENT Clear Command T9104
The timer T9104 is started, awaited CLEAR COMMAND and CLEAR REQUEST may be
repeated a maximum of 8 times.
Ed 04 CLEAR REQUEST
3BK 11202 0075 DSZZA
68
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
All causes which are not allowed or not unknown should be accepted by the MSC.
Ed 04 CLEAR REQUEST
3BK 11202 0075 DSZZA
69
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 1 0
0 0 0 0 0 1 0 0
Cause Length (value = 1)
0 Cause value
Ed 04 CLEAR REQUEST
3BK 11202 0075 DSZZA
70
FUNCTION The message is sent from BSC to MSC when a location updating CM
Service Request,CM Re-establishment Request, IMSI Detach, or Paging
Response message is received from the Mobile Station.
FOLLOWING
EVENT SCCP connect confirm SCCP Release T9105
DEFINITION
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0: Discriminator 1:
MCC, MNC
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
DEFINITION
It is used to pass Layer 3 messages from the Air interface to the MSC unchanged or
from the MSC to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1 1
Length 2
Layer 3 Information 3
N
It is the same message as received on the radio interface for the following messages :
CM-service Request
IMSI detach Indication
Location Updating Request
Paging response
CM re-establishment
It is just a transfer from Air to A Interface of the message received from the MS in the SABM
frame (from the user data of the "Establish Indication" message).
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 1 1 1
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont.
0 0 0 1 0 1 1 1
Layer 3 Length
Information Layer 3 Information
:
:
HANDOVER COMMAND
NAME Handover Command
FUNCTION This message is sent from MSC to BSC and contains the target channel
to which the MS should move to.
FOLLOWING
EVENT Access on new channel no access T8
DEFINITION
It is used to pass Layer 3 messages from the Air Interface to the MSC unchanged,
or from the MSC to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1 1
Length 2
Layer 3 Information 3
: :
: :
N
This information element contains in that message the "Handover Command" message
which has to be sent to the MS.
The coding is the same as the "Handover Command" in the Air Interface.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 1
0 0 0 1 0 1 1 1
Layer Length
3 Layer 3 Information
INFO : :
: :
FUNCTION This message sent by BSC to MSC indicates that the correct MS has
successfully accessed the target cell.
FOLLOWING
EVENT Old channel can be released. Handover failure
DEFINITION
This element is passed from the air interface to the MSC transparently, when
received from the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 1
RR Cause
RR Cause : the same value received (and same meaning) as the Handover Complete on
the Air Interface.
The RR Cause information, received from MS (in the "Handover complete" message) is
given to the MSC.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 0
0 0 0 1 0 1 0 1
RR CAUSE RR Cause optional
HANDOVER DETECT
NAME HANDOVER DETECT
FUNCTION This message is sent by the BSS to the MSC to report the reception of
the HANDOVER ACCESS from the Mobile Station, for the external
handover case.
FOLLOWING
EVENT - -
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 1
HANDOVER FAILURE
NAME HANDOVER FAILURE
FUNCTION This message may be sent by BSC to report failure during Handover in
the target or to indicate reversion to the old channel in the serving cell
FOLLOWING
EVENT - - T9110
(*)
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
(*) In case of discrepancies for cause value usage between this document and the 08.08
application document, then the 08.08 application document shall prevail.
Only this format is used (no extension).
DEFINITION :
This element is passed from the air interface to the MSC transparently, when
received from the MS.
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 1
RR Cause
The RR Cause information, received from MS (in the "handover failure" message), has
been stored, and is given to the MSC.
This element is optional because the BSC may send the "handover failure" message
without having received the same message from the MS.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 0
0 0 0 0 0 1 0 0
Cause Length (Value = 1)
0 Cause value
RR 0 0 0 1 0 1 0 1
Cause RR Cause optional
HANDOVER PERFORMED
NAME HANDOVER PERFORMED
FUNCTION This message is sent from the BSC to the MSC in order to indicate that
BSC has performed an Internal Handover (intracell or intercell)
FOLLOWING
EVENT
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
88
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
The mapping of handover alarm values detected by the Alcatel BSS handover algorithm to
the GSM cause values is described in ref. [24].
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
89
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0: Discriminator 1:
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
90
MCC, MNC :
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
91
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1
0 0 0 0 0 1 0 0
Cause Length (value=1)
0 Cause value
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont.
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
92
HANDOVER REQUEST
NAME HANDOVER REQUEST
FUNCTION This message is sent from the MSC to the BSS to indicate that the
Mobile Station is to be handed over to that BSS
INFORMATIO
N Header 1
ELEMENT Channel Type MV 5-10
LIST Encryption Information MF 11
Classmark Info 1 or 2 MF 2 or 4/5
Cell identifier (serving) MV 5-10
Priority OF 3
Circuit identity code OF 3
Radio channel identity OV not used 5-38
Downlink DTX flag OF 2
Cell identifier (target) OV (*) 5-10
Interference band to be used OF not used 2
FOLLOWING If no queuing :
EVENT New channel --> no failure
allocation if queuing and timer expires --
> clear request
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
93
DEFINITION
This element contains all of the information that the BSC requires to determine the
radio resource that is required.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 1 1
Length 2
spare Speech or data indicator 3
Channel Rate and type 4
For values 0001 and 0010 a dedicated terrestrial resource is also required.
0000 1000 Full rate TCH channel Bm. Preference between permitted speech versions or
full rate TCH as indicated in octet 5, 5a ...
0000 1001 Half rate TCH channel Lm. Preference between permitted speech versions or
half rate TCH as indicated in octet 5, 5a ...
0000 1010 Full or Half rate TCH channel, Full rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1011 Full or Half rate TCH channel, Half rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1111 Full or Half rate TCH channel, changes allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0001 1010 Full or Half rate TCH channel, Full rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1011 Full or Half rate TCH channel. Half rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1111 Full or Half rate TCH channel, changes not allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0000 0000 SDCCH or Full rate TCH channel Bm or Half rate TCH channel Lm
0000 0001 SDCCH
0000 0010 SDCCH or Full rate TCH channel Bm Not
supported
0000 0011 SDCCH or Half rate TCH channel Lm Not
supported
0000 1000 Full rate TCH channel Bm Not supported
0000 1001 Half rate TCH channel Lm Not supported
0000 1010 Full or Half rate TCH, FR preferred, changes allowed Not supported
0000 1011 Full or Half rate TCH, HR preferred, changes allowed Not supported
0001 1010 Full or Half rate TCH, FR preferred, changes not allowed Not supported
0001 1011 Full or Half rate TCH, HR preferred, changes not allowed Not supported
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
95
765 4321
000 0001 GSM speech full rate version 1
001 0001 GSM speech full rate version 2
010 0001 GSM speech full rate version 3 not supported
000 0101 GSM speech half rate version 1
001 0101 GSM speech half rate version 2 not supported
010 0101 GSM speech half rate version 3 not supported
Ext : reserved for extension, set to value 0 (= no extension) for this message.
For non-transparent service bits 6-1 indicate the radio interface data rate;
65 4321
00 0000 12 kbits/s for TCH FR
6 kbits/s for TCH HR Not supported
01 0000 12 kbits/s
01 0001 6 kbits/s Not supported
Stored in order to be able to allocate the required channel. Use for the sending of the
"Channel Activation" message to the BTS.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
96
DEFINITION
This element contains the user data encryption information used to control any
encryption equipment at the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted Algorithms
Key
: :
: :
Key (continued)
Algorithm Identifier
The permitted algorithms octet is a bit map indicating the encryption algorithms from which
the BSS may select the algorithm to be used.
Bit No
1 No encryption
2 GSM A5/1
3 GSM A5/2
4 GSM A5/3 Not supported
5 GSM A5/4 Not supported
6 GSM A5/5 Not supported
7 GSM A5/6 Not supported
8 GSM A5/7 Not supported
A bit position encoded as 1 indicates that the BSS may use the encryption algorithm
repesented by that bit position. A bit position encoded as 0 indicates that the BSS shall not
use the encryption algorithm represented by that bit position. A permitted algorithms octet
containing all bits encoded as 0 shall not be used.
The key shall be present if at least one of the A5 encryption algorithms is permitted. When
present, the MSC will send a key which shall be 8 octets long.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
97
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
98
DEFINITION
To provide the network with Information concerning the capabilities of the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 1 0 1
0 Revision 0 A5/1 RF power
level capab.
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
The BSC is non transparent to this parameter, in order to read the capabilities of the
attached MSs. This phase 2 format is always used by the BSC to decode this IE.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
99
DEFINITION :
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction as given by a MS supporting GSM phase 1.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
Revision Encryption RF power 3
level Algorithm Capability
0 0 0 0 SM. Frequency capability 4
cap
Octet 3
Bits 8 7 6
Revision level : 0 0 0 Reserved for phase 1.
All other values reserved
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
100
Octet 4
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 321
FC Frequency Capability : 0 0 0 Band no 0
Other values reserved.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
101
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
0 Revision 0 A5/1 RF power 3
spare level spare Capability
0 PS SS Screen. SM. 0 0 FC 4
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2 5
spare spare spare spare spare
Octet 3
Bits 76
Revision level : 00 Reserved for phase 1.
01 Used by phase 2 mobiles
All other values reserved
Bit 4
A5/1 : 0 algorithm A5/1 available
1 algorithm A5/1 not available.
Bits 321
RF Power capability :
GSM900 000 class 1
001 class 2
010 class 3
011 class 4
100 class 5
All other values reserved
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
102
Bits 65
SS Screening Indicator : 00
01
10
11
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 1
FC Frequency Capability : GSM900
0 The MS does not support the extension band
G1 in addition to the primary GSM band.
1 The MS does support the extension band G1.
DCS1800
0 Reserved for future use
Octet 5
Bit 8
CM3 Classmark 3 0 No additional MS capability
1 Additional MS capabilities are described in the
classmark 3 information element.
Bit 2
A5/3 algorithm supported 0 A5/3 not available
1 A5/3 available
Bit 1
A5/2 algorithm supported 0 A5/2 not available
1 A5/2 available
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
103
The BSC takes this information in order to have the MS power capability for the power
control and handover algorithm. Default values are used for 'revision level', 'RF Power
Capability' and MS cipher capability if the BSC can not decode these fields (see reference
[25]).
Additional mobile info can be obtained by invoking the classmark interrogation procedure.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
104
DEFINITION :
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identification 3
Discriminator
Cell Identification 4-10
Discriminator 0010:
4 CI value
5 CI value cont.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
105
MCC, MNC :
The BSC will use the cell identifier (serving) in order to identify if handover is synchronous
or asynchronous : If the serving cell identifier is incorrect (not belonging to the BSC or
unknown) then an asynchronous handover is performed.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
106
DEFINITION
Definition of the priority of the request for traffic channels only.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 0
Length
spare Priority level qa pe
Priority level
6543
0000 spare
0001 priority level 1 = highest priority
0010 priority level 2 = second highest priority
:
1110 Priority level 14 = lowest priority
1111 priority not used
if queuing is allowed (qa =1) and priority =1111 then lowest priority is assigned.
if queuing is allowed (qa =1) and priority =0000 then lowest priority is assigned.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
107
DEFINITION
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
Stored for further usage (to control if terrestrial channel is already in use).
In case of Signalling Channel type, the BSC reacts at the reception of this parameter with
an HANDOVER FAILURE (cause protocol error).
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
108
DEFINITION
This flag indicates if the DTX function in the BSS is to be disabled on a particular
radio channel.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 1
0 0 0 0 0 0 0 DTX
Flag
- in case of speech (full rate only), the DTX is sent to the BTS in the "CHANNEL
ACTIVATION" message.
- For Speech channel (full rate only), if not included, "DTX enabled" in downlink direction is
selected as default value.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
109
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 0 0
0 0 0 0 1 0 1 1
Length (value=3)
Channel spare Speech or data indicator
Type Channel Rate and type
0 0 0 0 1 0 1 0
Length (1 or 9)
Encryption Permitted Algorithms
Information Key
Key (continued)
Classmark Inf. 0 0 0 1 1 1 0 1
Type 1 0 Revision 0 A5/1 RF power
level capab.
OR
Classmark 0 0 0 1 0 0 1 0
Information Length (value=2)
Type 2 Revision Encrypt. RF power
level Algorithm Capability
(Phase 1 MS) 0 0 0 0 SM Freq.
Capa Capability
OR
0 0 0 1 0 0 1 0
Classmark Length=3
Information 0 Revision 0 A5/1 RF power
spare level spare Capability
Type 2 0 PS SS Screen. SM. 0 0 FC
spare Capa Indicator cap spare spare
(Phase 2 MS) CM3 0 0 0 0 0 A5/3 A5/2
spare spare spare spare spare
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
110
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5 or 3)
serving
option
/ I \
either: or: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0
LAC cont.
CI value
CI value cont.
0 0 0 0 0 1 1 0
Priority Length optional
spare Priority level qa pe
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part) optional
Code (Low part) TS in use
Downlink 0 0 0 1 1 0 0 1
DTX Flag 0 0 0 0 0 0 0 DTX optional
Flag
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
111
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5 or 3)
target
(optional) option
/ I \
either: or: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0
LAC cont.
CI value
CI value cont.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
112
FUNCTION This message is sent from BSC to MSC and indicates that the request to
support an Handover at the target BSS can be supported by the BSS,
and also to which radio channel the MS should be directed.
FOLLOWING
EVENT
Handover Command from Hand over failure T9113
MSC
Note This information field carries a radio interface "HANDOVER COMMAND" message
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
113
DEFINITION
It is used to pass Layer 3 messages from the Air Interface to the MSC unchanged,
or from the MSC to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1 1
Length 2
Layer 3 Information 3
: :
: :
N
This information element contains in that message the "Handover Command" message
which has to be sent to the MS.
The coding is the same as the "Handover Command" in the Air Interface.
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
114
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0
0 0 0 1 0 1 1 1
Layer Length
3 Layer 3 Information
INFO = Handover Command
Coded as on the radio interface
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
115
HANDOVER REQUIRED
NAME HANDOVER REQUIRED
FUNCTION This message is sent from the BSC to indicate that for a given MS which
already has a dedicated radio resource assigned, a handover is required
for the reason given by the cause element
FOLLOWING
EVENT Handover Request Handover Required T7
(optional) Reject (optional) T_HO_REQ_LOST
(*) n <= 16
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
116
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause
The BSC gives in this parameter the reason of the Handover requested to the MSC.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
117
DEFINITION :
To request that the MSC always responds to a HANDOVER REQUIRED message,
in particular if handover cannot be performed, to respond with HANDOVER
REQUIRED REJECT.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 1
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
118
DEFINITION :
This element uniquely identifies cells within a BSS and is of variable length N. P is
the number of elements within the list and the range for P is 1 to 16 (included).
BIT DESCRIPTION
Cell 0 0 0 1 1 0 1 0
Identifier Length (value = 1+Px7) or 1+Px4
spare Cell Identif.Discriminator 3
Cell 1, format depends on Cell Id Discriminator 4 to 7 4
octets.
.. .. .. ..
Cell P, format depends on Cell Id Discriminator 4 to 7 N
octets.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
119
Length = 1 + 7 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CI value 9
CI value cont. 10
CELL P
MCC digit 2 MCC digit 1 N-6
1 1 1 1 MCC digit 3 N-5
MNC digit 2 MNC digit 1 N-4
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
120
Length = 1 + 4 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CI value 6
CI value cont. 7
CELL P
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
MCC, MNC :
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS-
O&M parameter.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
121
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 0 1
0 0 0 0 0 1 0 0
Length
0 Cause
Resp. Req 0 0 0 1 1 0 1 1 optional
0 0 0 1 1 0 1 0
Length (value = 1+Px7) or 1+Px4
Cell
Identifier option
list / \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont. CELL 1
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
122
FUNCTION This message may be sent by MSC to report that a previously requested
handover could not be executed.
FOLLOWING T_HO_
REQ_LOST
EVENT
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause
The BSC does not use nor check the cause value for this message.
Only this format (without extension) is expected by the BSC.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 0
0 0 0 0 0 1 0 0
CAUSE Length
0 Cause
OVERLOAD
NAME OVERLOAD (A Interface)
FUNCTION This message is sent from the MSC to BSS or from BSS to MSC to
report an Overload situation at the message sender.
FOLLOWING
EVENT T5
T6
T17
T18
Ed 04 OVERLOAD
3BK 11202 0075 DSZZA
126
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause Value
Ed 04 OVERLOAD
3BK 11202 0075 DSZZA
127
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 0 1 0
0 0 0 0 0 1 0 0
Cause Length (value = 1)
0 Cause Value
Ed 04 OVERLOAD
3BK 11202 0075 DSZZA
128
PAGING
NAME PAGING
FUNCTION This message is sent from MSC to BSC and contains sufficient
information to allow the paging message to be transmitted at the correct
time
FOLLOWING
EVENT BSC sends "Paging"
command to BTS
Note If the Cell identifier list is not present the Paging Command is sent in all cells of this
BSC.
Ed 04 PAGING
3BK 11202 0075 DSZZA
129
DEFINITION
Value of IMSI
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 0 0 1
Length 2
Id digit 1 OEI Type of Id 3
Id digit 3 Id digit 2 4
.. .. .. ..
Id digit p+1 Id digit p N
0 0 0 0 1 0 0 0 1
Length 2
0 0 0 1 0 0 0 1 3
0 1 1 0 1 0 0 0 4
0 1 0 0 0 1 0 1 5
1 1 1 1 0 0 1 1 6
Ed 04 PAGING
3BK 11202 0075 DSZZA
130
DEFINITION
Value of TMSI
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 0 1 1
Length (value = 4) 2
TMSI value 3
TMSI value contd. 4
TMSI value contd. 5
TMSI value contd. 6
Bit 8 of octet 3 is the most significant bit, and bit 1 of octet 6 is the least significant bit.
If the length of TMSI is less 4 octets, the MSC should fill the field with zeroes in front of the
MSB.
Ed 04 PAGING
3BK 11202 0075 DSZZA
131
DEFINITION
Identifies a list of cells within a BSS. Let P be the number of cells in the list.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 0 1
Length 2
spare Cell Identif.Discriminator 3
Cell 1, format depends on Cell Id Discriminator 2 to 7 4
octets.
.. .. .. ..
Cell P, format depends on Cell Id Discriminator 2 to 7 P
octets.
Ed 04 PAGING
3BK 11202 0075 DSZZA
132
Length = 1 + 7 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CI value 9
CI value cont. 10
CELL P
MCC digit 2 MCC digit 1 N-6
1 1 1 1 MCC digit 3 N-5
MNC digit 2 MNC digit 1 N_4
LAC N_3
LAC cont. N_2
CI value N_1
CI value cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
133
Length = 1 + 4 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CI value 6
CI value cont. 7
CELL P
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
Length = 1 + 2 x P
Octets 4 to N:
CELL 1
CI value 4
CI value cont. 5
CELL P
CI value N-1
CI value cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
134
Length = 1
Octets 4 to N: NONE
Length = 1 + 5 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CELL P
MCC digit 2 MCC digit 1 N-4
1 1 1 1 MCC digit 3 N-3
MNC digit 2 MNC digit 1 N-2
LAC N-1
LAC cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
135
Length = 1 + 2 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CELL P
LAC N-1
LAC cont. N
Length = 1
Octets 4 to N: NONE
MCC, MNC
Values (1,4,5,6) are accepted by the BSS. Values (2,3) should not be used by the MSC:
value (3) does not make sense for paging, and value (2) is not sufficient information.
However, in those two last cases paging will be done to all cells of the BSS.
Ed 04 PAGING
3BK 11202 0075 DSZZA
136
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 0 1 0
0 0 0 0 1 0 0 0
Length
Id digit 1 OEI 0 0 1
IMSI Id digit 3 Id digit 2
.. .. .. ..
Id digit p+1 Id digit P
0 0 0 0 1 0 0 1
Length (value = 4)
TMSI TMSI value
(optional) TMSI value contd.
TMSI value contd.
TMSI value contd.
0 0 0 1 1 0 1 0
Length
Cell Cell Identif.Discriminator
Identifier Cell 1, format depends on Cell Id Discriminator 2 to 7
octets.
List .. .. .. ..
(optional) Cell P, format depends on Cell Id Discriminator 2 to 7
octets.
Ed 04 PAGING
3BK 11202 0075 DSZZA
137
QUEUING INDICATION
NAME QUEUING INDICATION
FUNCTION This message is sent from the BSC to the MSC in order to indicate a
delay in the assignment of the required TCH.
FOLLOWING
EVENT T11
Tqho
One of the above timers is started when the message is sent from the BSC to the MSC.
Ed 04 QUEUING INDICATION
3BK 11202 0075 DSZZA
138
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 1 1 0
Ed 04 QUEUING INDICATION
3BK 11202 0075 DSZZA
139
RESET
NAME RESET
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message indicates to the receiving entity that the transmitting entity
has suffered a failure and has lost memory of the call in progress, call set
up and associated references.
FOLLOWING
EVENT T4
T13
T2
T16
Ed 04 RESET
3BK 11202 0075 DSZZA
140
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
The MSC or BSC gives in this parameter the reason of the Reset.
In the MSC -> BSS direction, the BSS does not use or check the cause values.
Ed 04 RESET
3BK 11202 0075 DSZZA
141
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 0 0 0
0 0 0 0 0 1 0 0
Length (value=1)
0 Cause value
Ed 04 RESET
3BK 11202 0075 DSZZA
142
RESET ACKNOWLEDGE
NAME RESET ACKNOWLEDGE
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message can be sent either from the MSC to the BSC or from the
BSC to the MSC. It indicates to the receiving entity that the transmitting
entity has cleared all calls and reset all references and is ready to
resume service.
FOLLOWING
EVENT T4
T16
T13
T2
Ed 04 RESET ACKNOWLEDGE
3BK 11202 0075 DSZZA
143
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 0 0 1
Ed 04 RESET ACKNOWLEDGE
3BK 11202 0075 DSZZA
144
RESET CIRCUIT
NAME RESET CIRCUIT
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
This message is sent from the BSS to the MSC or from the MSC to the
FUNCTION BSS to indicate that a circuit and its associated reference should be
reinitialised, due to some abnormal event.
FOLLOWING
EVENT Reset Circuit Start
Acknowledge T12 Expiry T12
T19
Ed 04 RESET CIRCUIT
3BK 11202 0075 DSZZA
145
DEFINITION
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
This parameter is given to the MSC or to the BSC in order to identify a specific terrestrial
channel.
Ed 04 RESET CIRCUIT
3BK 11202 0075 DSZZA
146
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
Used causes
BSC to MSC:
110 0000 Protocol Error between BSC and MSC
MSC to BSC:
Any cause is accepted by the BSC
Ed 04 RESET CIRCUIT
3BK 11202 0075 DSZZA
147
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 1 0 0
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part)
Code Low part TS in use
0 0 0 0 0 1 0 0
Cause Length
0 Cause value
Ed 04 RESET CIRCUIT
3BK 11202 0075 DSZZA
148
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message is sent from the MSC to the BSC to acknowledge the
receipt of an earlier RESET CIRCUIT and to indicate that the circuit
concerned has been reinitialised.
FOLLOWING
EVENT
Stop
T12
T19
DEFINITION
Defines the terrestrial channel
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
Low part TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
This parameter is given to the BSC or MSC in order to identify a specific terrestrial channel.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 1 0 1
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part)
Code Low part TS in use
FUNCTION The message is sent from the MSC to the BSC or vice versa in order to
instruct the receiving entity to release resources concerned with SAPI "n"
FOLLOWING
EVENT
T9104
DEFINITION
This is a fixed length element indicating the channel on which the SAPI value over
the air interface that the transaction concerns.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 0
Spare 0 0 0 SAPI
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 1 1
DLCI 0 0 0 1 1 0 0 0
Spare 0 0 0 SAPI
FUNCTION The message is sent from the BSC to the MSC in order to indicate that a
message with a SAPI value other than 0 has been rejected.
FOLLOWING
EVENT
DEFINITION
This is a fixed length element indicating the channel on which the SAPI value over
the air interface that the transaction concerns.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 0
Spare 0 0 0 SAPI
DEFINITION
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause Value
Used causes.
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 1 0 1
DLCI 0 0 0 1 1 0 0 0
Spare 0 0 0 SAPI
Cause 0 0 0 0 0 1 0 0
Length=1
0 Cause Value
TRACE INVOCATION
NAME TRACE INVOCATION
CHANNEL/ SCCP
USAGE Connection
GSM-REF 08.08
FUNCTION This message is sent from the MSC to the BSC to Request the start of a
trace, and from the BSC to MSC to report that a trace has been initiated
at the BSS by the OMC (or local terminal).
FOLLOWING
EVENT
Ed 04 TRACE INVOCATION
3BK 11202 0075 DSZZA
159
DEFINITION
Reference used to identify the connection being traced.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 0 1
Trace number 2
Trace number (continued) 3
Used inside the receiving entity to create a unique trace record identifier.
Ed 04 TRACE INVOCATION
3BK 11202 0075 DSZZA
160
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 0 1 1
0 0 0 1 0 1 1 0
Trace Trace number
Number Trace number (continued)
Ed 04 TRACE INVOCATION
3BK 11202 0075 DSZZA
161
UNBLOCK
NAME UNBLOCK
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message is sent from the BSC to the MSC to indicate that a
particular terrestrial resource (i.e. a particular timeslot within a 2Mbit
system) may be returned to service at the MSC and can therefore be
used for traffic.
FOLLOWING
EVENT
T1_short
Ed 04 UNBLOCK
3BK 11202 0075 DSZZA
162
DEFINITION
Defines the terrestrial channel
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
Low part
PCM Multiplex )
) defines the terrestrial channel
TS in use )
The BSC gives to the MSC the Identification of the terrestrial channel which becomes
available.
Ed 04 UNBLOCK
3BK 11202 0075 DSZZA
163
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 1 0
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part)
Code Low part TS in use
Ed 04 UNBLOCK
3BK 11202 0075 DSZZA
164
UNBLOCKING ACKNOWLEDGE
NAME UNBLOCKING ACKNOWLEDGE
CHANNEL/ SCCP
USAGE Connectionless
GSM-REF 08.08
FUNCTION This message is sent from the MSC to the BSC to acknowledge the
receipt of an earlier unblock message, and to indicate that the circuit
concerned has been returned to service.
FOLLOWING
EVENT
Ed 04 UNBLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
165
DEFINITION
Defines the terrestrial channel
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
Low part
PCM Multiplex )
) defines the terrestrial channel
TS in use )
The MSC gives to the BSC the Identification of the terrestrial channel which becomes
available.
Ed 04 UNBLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
166
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 1 1
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part)
Code Low part TS in use
Ed 04 UNBLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
167
Ed 04
3BK 11202 0075 DSZZA
168
ASSIGNMENT COMPLETE
NAME ASSIGNMENT COMPLETE -- A Interface
This message is sent from BSC to MSC and indicates that the requested
FUNCTION assignment has been completed correctly.
FOLLOWING
EVENT Procedure to be continued on Message replaced by assign
allocated channel. failure
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
169
DEFINITION
This element is passed from the air interface to the MSC transparently, when
received from the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 0 1
RR Cause
RR Cause the same value received (and same meaning) as the Assignment Complete on
the Air Interface.
The RR Cause information, received from MS (in the "assignment complete" message), has
been stored, and is given to the MSC.
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
170
DEFINITION
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0 : Discriminator 1 :
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
171
MCC, MNC
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
172
DEFINITION
Description of the channel allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 1 1
spare Channel 2
Channel
Bit 4321
0001 SDCCH
1000 Full rate TCH
1001 Half rate TCH
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
173
DEFINITION
Description of the encryption algorithm allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 1 1 0 0 1
Algorithm Identifier 2
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
174
DEFINITION
Speech version being used by the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0 1
spare Speech version identifier 2
Speech version identifier is coded in the same way as the permitted speech version
identifier in the Channel type information element.
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
175
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 1 0
RR 0 0 0 1 0 1 0 1
Cause RR Cause
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0
MCC digit 2 MCC digit 1
1 1 1 1 MCC digit 3
MNC digit 2 MNC digit 1 0 0 0 0 0 0 0 1
LAC LAC
LAC cont. LAC cont.
CI value CI value
CI value cont. CI value cont.
Chosen 0 0 1 0 0 0 0 1 0 0 1 0 0 0 0 1
Channel spare Channel spare Channel
Chosen 0 0 1 0 1 1 0 0 0 0 1 0 1 1 0 0
Encryp. Algorithm Identifier Algorithm Identifier
Algo.
Speech 0 1 0 0 0 0 0 0
Version spare Speech version identifier optional
Ed 04 ASSIGNMENT COMPLETE
3BK 11202 0075 DSZZA
176
ASSIGNMENT FAILURE
As Phase 1
New Causes :
ASSIGNMENT REQUEST
NAME ASSIGNMENT REQUEST
FUNCTION Used by the MSC to the BSC in order to request the BSS to assign radio
resource, the attributes of which are defined within the message.
FOLLOWING
EVENT Assignment command sent to Assignment failure sent to the
the MS after the Channel MSC
Allocation T 10
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
178
DEFINITION
This element contains all of the information that the BSC requires to determine the
radio resource that is required.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 1 1
Length 2
spare Speech or data indicator 3
Channel Rate and type 4
For values 0001 and 0010 a dedicated terrestrial resource is also required.
0000 1000 Full rate TCH channel Bm. Preference between permitted speech versions or
full rate TCH as indicated in octet 5, 5a ...
0000 1001 Half rate TCH channel Lm. Preference between permitted speech versions or
half rate TCH as indicated in octet 5, 5a ...
0000 1010 Full or Half rate TCH channel, Full rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1011 Full or Half rate TCH channel, Half rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1111 Full or Half rate TCH channel, changes allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0001 1010 Full or Half rate TCH channel, Full rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1011 Full or Half rate TCH channel. Half rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1111 Full or Half rate TCH channel, changes not allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0000 0000 SDCCH or Full rate TCH channel Bm or Half rate TCH channel Lm
0000 0001 SDCCH
0000 0010 SDCCH or Full rate TCH channel Bm Not
supported
0000 0011 SDCCH or Half rate TCH channel Lm Not
supported
0000 1000 Full rate TCH channel Bm Not supported
0000 1001 Half rate TCH channel Lm Not supported
0000 1010 Full or Half rate TCH, FR preferred,changes allowed Not supported
0000 1011 Full or Half rate TCH, HR preferred, changes allowed Not supported
0001 1010 Full or Half rate TCH, FR preferred, changes not allowed Not supported
0001 1011 Full or Half rate TCH, HR preferred, changes not allowed Not supported
765 4321
000 0001 GSM speech full rate version 1
001 0001 GSM speech full rate version 2
010 0001 GSM speech full rate version 3 not supported
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
180
Ext : reserved for extension, set to value 0 (= no extension) for this message.
For non-transparent service bits 6-1 indicate the radio interface data rate;
65 4321
00 0000 12 kbits/s for TCH/FR
6 kbits/s for TCH/HR Not supported
01 0000 12 kbits/s
01 0001 6 kbits/s Not supported
Stored in order to be able to allocate the required channel. Use for the sending of the
"Channel Activation" message to the BTS and the "Assignment Command" message to the
MS.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
181
DEFINITION
This element is used to supply the BSS with information that needs to be included in
the header of layer 3 messages over the radio interface.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 1
Length (value = 2)
0 0 0 0 Protocol Discriminator
0 0 0 0 Transaction Identifier
Protocol Discriminator and Transaction Identifier are used in order to have information for
the sending of the "Assignment Command" message to the MS. Refer to the general part at
the beginning of this dictionary.
GSM states that this IE has no useful purpose. Thus contents of this information element
will be ignored by the BSC.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
182
DEFINITION
Definition of the priority of the request for traffic channels only.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 0
Length
spare pci Priority level qa pvi
priority level:
6543
0 0 0 0 spare
0 0 0 1 priority level 1 = highest priority
0 0 1 0 priority level 2 = second highest priority
::::
1 1 1 0 priority level 14 = lowest priority
1 1 1 1 priority not used
if queuing is allowed (qa =1) and priority =1111 then lowest priority is assigned.
if queuing is allowed (qa =1) and priority =0000 then lowest priority is assigned.
- Taken into account in order to queue, if needed, the message. Only 'Pre-emption'
not allowed is used by the MSC.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
183
DEFINITION
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
In case of Signalling Channel type, the BSC reacts at the reception of this parameter with
an ASSIGNMENT FAILURE (cause protocol error).
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
184
DEFINITION
This flag indicates if the DTX function in the BSS is to be disabled on a particular
radio channel.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 1
0 0 0 0 0 0 0 DTX
Flag
- in case of speech (full rate only), the DTX is sent to the BTS in the "CHANNEL
ACTIVATION" message.
- For Speech channel (full rate only), if not included, "DTX enabled" in downlink direction is
selected as default value.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
185
DEFINITION :
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction as given by a MS supporting GSM phase 1.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
Revision Encryption RF power 3
level Algorithm Capability
0 0 0 0 SM. Frequency capability 4
cap
Octet 3
Bits 8 7 6
Revision level : 0 0 0 Reserved for phase 1.
All other values reserved
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
186
Octet 4
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 321
FC Frequency Capability : 0 0 0 Band no 0
Other values reserved.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
187
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
0 Revision 0 A5/1 RF power 3
spare level spare Capability
0 PS SS Screen. SM. 0 0 FC 4
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2 5
spare spare spare spare spare
Octet 3
Bits 76
Revision level : 00 Reserved for phase 1.
01 Used by phase 2 mobiles
All other values reserved
Bit 4
A5/1 : 0 algorithm A5/1 available
1 algorithm A5/1 not available
Bits 321
RF Power capability :
GSM900 000 class 1
001 class 2
010 class 3
011 class 4
100 class 5
All other values reserved
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
188
Bits 65
SS Screening Indicator : 00
01
10
11
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 1
FC Frequency Capability : GSM900
0 The MS does not support the extension band
G1 in addition to the primary GSM band.
1 The MS does support the extension band G1.
DCS1800
0 Reserved for future use
Octet 5
Bit 8
CM3 Classmark 3 0 No additional MS capability
1 Additional MS capabilities are described in the
classmark 3 information element.
Bit 2
A5/3 algorithm supported 0 A5/3 not available
1 A5/3 available
Bit 1
A5/2 algorithm supported 0 A5/2 not available
1 A5/2 available
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
189
The BSC takes this information in order to have the MS power capability for the power
control and algorithm information. Default values are used for 'revision level', 'RF Power
Capability' and MS cipher capability if the BSC can not decode these fields (see reference
[25]).
Additional mobile info can be obtained by invoking the classmark interrogation procedure.
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
190
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
0 0 0 0 1 0 1 1
Length (value=3)
Channel spare Speech or data indicator
Type Channel Rate and type
0 0 0 0 0 1 1 1
Layer 3 Length (value=2)
Header 0 0 0 0 Proto. Discrim
Information 0 0 0 0 Transac. Identifier
0 0 0 0 0 1 1 0
Priority Length (value=1)
spare pci Priority Level qa pvi
Circuit 0 0 0 0 0 0 0 1
Identity PCM Multiplex in use (high part)
Code Low part TS in use
Downlink DTX 0 0 0 1 1 0 0 1
Flag 0 0 0 0 0 0 0 DTX
(Optional Flag
0 0 0 1 0 0 1 0
Classmark Length = 2
Information Revision Encryption RF power
level Algorithm Capability
Type 2 0 0 0 0 SM. Frequency
(Phase 1 MS) cap capability
OR
0 0 0 1 0 0 1 0
Length = 3
Classmark 0 Revision 0 A5/1 RF power
Information spare level spare Capability
Type 2 0 PS SS Screen. SM. 0 0 FC
spare Capa Indicator cap spare spare
(Phase 2 MS) CM3 0 0 0 0 0 A5/3 A5/2
spare spare spare spare spare
Ed 04 ASSIGNMENT REQUEST
3BK 11202 0075 DSZZA
191
CHANNEL/ SCCP
USAGE Connection
GSM-REF 08.08
FUNCTION This message is sent from the BSC to MSC to request the start of a trace
procedure at the MSC.
FOLLOWING
EVENT
(1) Not used by the BSC but if received, they are copied to the trace record.
DEFINITION
Trace type.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 1 0 1
Trace type
Trace type is coded as the MSC/BSS Trace Type specified in GSM TS 12.08.
DEFINITION
A fixed length element indicating whether the trace is to be continued in a BSS to
which the call has been handed over.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 1 0 1 1
Spare Forward Indicator
DEFINITION
A variable length element indicating the identity of the entity which initiated the
trace.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 0 1 1 0 1
Length 2
Entity identity 3-22
DEFINITION
Reference used to identify the connection being traced.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 octet
0 0 1 0 0 1 1 1 1
Trace Reference 2-3
DEFINITION
A potentially variable length element indicating a particular transaction within a trace.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 1 0 0 0 1
Length 2
Transaction number 3-4
DEFINITION
A variable length element indicating the destination OMC to which trace
information is to be sent.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 1 0 1 0 1
Length 2
OMC Identity 3-32
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 1 1 1
Trace 0 0 1 0 0 1 0 1
Type Trace type
Forward 0 0 1 0 1 0 1 1
Indicator Spare Forward Indicator
Trace 0 0 1 0 0 1 1 1
Reference Trace
reference
BLOCK
Ed 04 BLOCK
3BK 11202 0075 DSZZA
200
BLOCKING ACKNOWLEDGE
Ed 04 BLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
201
FUNCTION This message is sent from MSC to BSC via the relevant SCCP
connection associated with that MS transaction. It updates the encryption
parameters for the concerned MS.
FOLLOWING
EVENT
Next valid frame which may
be the "ciphering mode -
complete"
DEFINITION
This element is used to supply the BSS with information that needs to be included in
the header of layer 3 messages over the radio interface.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
1 0 0 0 0 0 1 1 1
2 Length = 2
3 0 0 0 0 Protocol
Discriminator
4 0 0 0 0 Transaction
Identifier
Protocol Discriminator and Transaction Identifier are used in order to have information for
the sending of the "Ciphering Mode Command" message to the MS.
Refer to the general part at the beginning of this dictionary.
DEFINITION
This element contains the user data encryption information used to control any
encryption equipment at the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted algorithms
Key
: :
: :
Key (continued)
Permitted Algorithms
Bit no
1 : no encryption required
2 : GSM A5/1
3 : GSM A5/2
4 : GSM A5/3 Not supported
5 : GSM A5/4 Not supported
6 : GSM A5/5 Not supported
7 : GSM A5/6 Not supported
8 : GSM A5/7 Not supported
A bit position encoded as 1 indicates that the BSS may use the encryption algorithm
repesented by that bit position. A bit position encoded as 0 indicates that the BSS shall not
use the encryption algorithm represented by that bit position. A permitted algorithms octet
containing all bits encoded as 0 shall not be used.
The key shall be present if at least one of the A5 encryption algorithms is permitted. When
present, the MSC will send a key which shall be 8 octets long.
Stored at the BSC in order to be able to give the information to the BTS (during internal
Handover for example, or when the BSC allocates a TCH).
DEFINITION
This element is used by the MSC to indicate whether the IMEISV is to be included in
the CIPHERING MODE COMPLETE message to be sent by the mobile station.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 1 1 1
Cipher response mode 2
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 0 1 1
0 0 0 0 0 1 1 1
Layer 3 Length (value = 2)
Header 0 0 0 0 Protocol Optional
Discriminator
Information 0 0 0 0 Transaction
Identifier
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted Algorithms
Encryption Key
Information : :
: :
Key (continued)
Cipher 0 0 1 0 0 0 1 1 Optional
response mode Cipher response mode
FUNCTION This message sent from BSC to MSC indicates that a successful cipher
synchronisation has been achieved across the Air Interface.
FOLLOWING
EVENT
- - -
This message is sent to the MSC only if the ciphering mode complete was received from
the MS.
(1) Only included if the length of the CIPHERING MODE COMPLETE message received
on the Air interface is greater than 2 octets.
(2) This will only be included if the MSC indicates that more than one ciphering algorithm
is permitted. This possibility would have been indicated to the BSC in the Encryption
Information IE contained in the last received HANDOVER REQUEST or CIPHER
MODE COMMAND messages.
DEFINITION
It is used to pass Layer 3 messages from the Air interface to the MSC unchanged.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 0 1
Length 2
Layer 3 Information 3-n
This is the unchanged layer 3 message as received from the air interface.
It is just a transfer from Air to A Interface of the message received from the MS
DEFINITION
Description of the encryption algorithm allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 1 1 0 0 1
Algorithm Identifier 2
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 1
0 1 0 0 0 0 0 0
Layer 3 message Length
contents.
Layer 3 Information
Chosen 0 0 1 0 1 1 0 0 Optional
encr. algo. Algorithm Identifier
FUNCTION This message sent from BSC to MSC to indicate that it is unable to
perform the requested ciphering.
FOLLOWING
EVENT
- - -
DEFINITION
It is used to indicate the reason for a particular event to have occured..
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0 1
Length 2
Ext Cause value 3
Ext bit =0
The following cause values are supported
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 1 0 0 1
0 0 0 0 0 1 0 0
Cause Length
0 Cause value
CLASSMARK REQUEST
NAME CLASSMARK REQUEST
FUNCTION This message is sent by the MSC to the BSC to request an update of
Classmark information from the Mobile Station (via the classmark enquiry
procedure).
FOLLOWING
EVENT
Ed 04 CLASSMARK REQUEST
3BK 11202 0075 DSZZA
214
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 1 0 0 0
Ed 04 CLASSMARK REQUEST
3BK 11202 0075 DSZZA
215
CLASSMARK UPDATE
NAME CLASSMARK UPDATE
FOLLOWING
EVENT -
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
216
DEFINITION :
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction as given by a MS supporting GSM phase 1.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
Revision Encryption RF power 3
level Algorithm Capability
0 0 0 0 SM. Frequency capability 4
cap
Octet 3
Bits 8 7 6
Revision level : 0 0 0 Reserved for phase 1.
All other values reserved
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
217
Octet 4
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 321
FC Frequency Capability : 0 0 0 Band no 0
Other values reserved.
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
218
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
0 Revision 0 A5/1 RF power 3
spare level spare Capability
0 PS SS Screen. SM. 0 0 FC 4
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2 5
spare spare spare spare spare
Octet 3
Bits 76
Revision level : 00 Reserved for phase 1.
01 Used by phase 2 mobiles
All other values reserved
Bit 4
A5/1 : 0 algorithm A5/1 available
1 algorithm A5/1 not available.
Bits 321
RF Power capability :
GSM900 000 class 1
001 class 2
010 class 3
011 class 4
100 class 5
All other values reserved
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
219
Bits 65
SS Screening Indicator : 00
01
10
11
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 1
FC Frequency Capability : GSM900
0 The MS does not support the extension band
G1 in addition to the primary GSM band.
1 The MS does support the extension band G1.
DCS1800
0 Reserved for future use
Octet 5
Bit 8
CM3 Classmark 3 0 No additional MS capability
1 Additional MS capabilities are described in the
classmark 3 information element.
Bit 2
A5/3 algorithm supported 0 A5/3 not available
1 A5/3 available
Bit 1
A5/2 algorithm supported 0 A5/2 not available
1 A5/2 available
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
220
The BSC takes this information in order to have the MS power capability for the power
control and algorithm information. Default values are used for 'revision level', 'RF Power
Capability' and MS cipher capability if the BSC can not decode these fields (see reference
[25]).
Additional mobile info can be obtained by invoking the classmark interrogation procedure.
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
221
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 1 1
Length of mobile station classmark 3 contents 2
0 0 0 0 A5/7 A5/6 A5/5 A5/4 3
0 0 0 0 0 0 0 0 4-14
Spare
Octet 3
Bit 1
A5/4 algorithm supported 0 A5/4 not available
1 A5/4 available
Bit 2
A5/5 algorithm supported 0 A5/5 not available
1 A5/5 available
Bit 3
A5/6 algorithm supported 0 A5/6 not available
1 A5/6 available
Bit 4
A5/7 algorithm supported 0 A5/7 not available
1 A5/7 available
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
222
GENERAL DESCRIPTION
GSM PHASE 1 MS
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 0
Classmark 0 0 0 1 0 0 1 0
Information Length
Type 2 Revision Encryption RF power
(Phase 1 MS) level Algorithm Capability
0 0 0 0 SM. Frequency capability
cap
GSM PHASE 2 MS
8 7 6 5 4 3 2 1
0 1 0 1 0 1 0 0
0 0 0 1 0 0 1 0
Classmark Length = 3
Info 2 0 Revision 0 A5/1 RF power
spare level spare Capability
(Phase 2 MS) 0 PS SS Screen. SM. 0 0 FC
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2
spare spare spare spare spare
Ed 04 CLASSMARK UPDATE
3BK 11202 0075 DSZZA
223
CLEAR COMMAND
The same format as phase 1 except that the layer 3 header is optional for phase 2.
Ed 04 CLEAR COMMAND
3BK 11202 0075 DSZZA
224
CLEAR COMPLETE
As phase 1
Ed 04 CLEAR COMPLETE
3BK 11202 0075 DSZZA
225
CLEAR REQUEST
As phase 1
Ed 04 CLEAR REQUEST
3BK 11202 0075 DSZZA
226
FUNCTION The message is sent from BSC to MSC when a location updating, CM
Service Request, CM Re-establishment Request, IMSI Detach, or
Paging Response message is received from the Mobile Station.
FOLLOWING
EVENT SCCP connect confirm SCCP Release T9105
DEFINITION
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0 : Discriminator 1 :
MCC, MNC
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
DEFINITION
It is used to pass Layer 3 messages from the Air interface to the MSC unchanged or
from the MSC to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1 1
Length 2
Layer 3 Information 3
N
It is the same message as received on the radio interface for the following messages :
CM-service Request
IMSI detach Indication
Location Updating Request
Paging response
CM Establishment
It is just a transfer from Air to A Interface of the message received from the MS in the SABM
frame (from the user data of the "Establish Indication" message).
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 1 1 1
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont.
0 0 0 1 0 1 1 1
Layer 3 Length
Information Layer 3 Information
:
:
HANDOVER COMMAND
HANDOVER COMPLETE
HANDOVER DETECT
HANDOVER FAILURE
New Cause:
HANDOVER PERFORMED
NAME HANDOVER PERFORMED
FUNCTION This message is sent from the BSC to the MSC in order to indicate that
BSC has performed an Internal Handover (intracell or intercell)
FOLLOWING
EVENT
(1) This IE is never sent after the immediate assignment procedure and before either
TCH assignment or external handover.
After TCH assignment or external handover, the chosen channle IE is only sent when
the channel type in either the last received ASSIGMENT REQUEST or HANDOVER
REQUEST indicates one of the following codings :
For signalling connections (i.e. SDCCH)- when the channel type indicates 'No
preferences'
For Speech or Data connections (i.e. TCH) - when the channel type indicates "Full or
Half rate", with a preference, with or without changes allowed.
(2) This will only be included if the MSC indicates that more than one ciphering algorithm
is permitted. This possibilitty would have been indicated to the BSC in the Encryption
Information IE contained in the last received HANDOVER REQUEST or CIPHER
MODE COMMAND messages.
(3) Included at least when the speech version has been changed by the BSS.
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
236
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause value
The mapping of handover alarm values detected by the Alcatel BSS handover algorithm to
the GSM cause values is described in ref. [24].
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
237
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identif. Discriminator 3
Cell Identification 4 - 10
Discriminator 0 : Discriminator 1 :
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
238
MCC, MNC :
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS
parameter.
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
239
DEFINITION
Description of the channel allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 1 1
spare Channel 2
Channel
Bit 4321
0001 SDCCH
1000 Full rate TCH
1001 Half rate TCH
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
240
DEFINITION
Description of the encryption algorithm allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 1 1 0 0 1
Algorithm Identifier 2
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
241
DEFINITION
Speech version being used by the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0 1
spare Speech version identifier 2
Speech version identifier is coded in the same way as the permitted speech version
identifier in the Channel type information element.
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
242
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1
0 0 0 0 0 1 0 0
Cause Length = 1
0 Cause value
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5)
option
/ \
either: or:
0 0 0 0 0 0 0 0
MCC digit 2 MCC digit 1
1 1 1 1 MCC digit 3
MNC digit 2 MNC digit 1 0 0 0 0 0 0 0 1
LAC LAC
LAC cont. LAC cont.
CI value CI value
CI value cont. CI value cont.
Chosen 0 0 1 0 0 0 0 1 0 0 1 0 0 0 0 1
Channel spare Channel spare Channel
Chosen 0 0 1 0 1 1 0 0 0 0 1 0 1 1 0 0
Encryp. Algorithm Identifier Algorithm Identifier
Algo.
Speech 0 1 0 0 0 0 0 0
Version spare Speech version identifier optional
Ed 04 HANDOVER PERFORMED
3BK 11202 0075 DSZZA
243
HANDOVER REQUEST
NAME HANDOVER REQUEST
FUNCTION This message is sent from the MSC to the BSS to indicate that the
Mobile Station is to be handed over to that BSS
INFORMATIO
N Header MF 1
ELEMENT Channel Type MF 5-10
LIST Encryption Information MF 11
Classmark Info 1 or 2 MF 2 or 4/5
Cell identifier (serving) MV 5-10
Priority OF 3
Circuit identity code OF 3
Downlink DTX flag OF 2
Cell identifier (target) MV (1) 7-10
Interference band to be used OF Not used 2
Cause OF (2) 3
Classmark info 3 OV Not used 3-14
Current channel OF Not used 2
Speech version (used) OF 2
Group call reference OF Not used 5
IMPLEMENTATION MAXIMUM LENGTH 60
FOLLOWING If no queuing :
EVENT New channel --> no failure
allocation if queuing and timer expires --
> clear request
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
244
DEFINITION
This element contains all of the information that the BSC requires to determine the
radio resource that is required.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 1 1
Length 2
spare Speech or data indicator 3
Channel Rate and type 4
For values 0001 and 0010 a dedicated terrestrial resource is also required.
0000 1000 Full rate TCH channel Bm. Preference between permitted speech versions or
full rate TCH as indicated in octet 5, 5a ...
0000 1001 Half rate TCH channel Lm. Preference between permitted speech versions or
half rate TCH as indicated in octet 5, 5a ...
0000 1010 Full or Half rate TCH channel, Full rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1011 Full or Half rate TCH channel, Half rate preferred, changes allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0000 1111 Full or Half rate TCH channel, changes allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0001 1010 Full or Half rate TCH channel, Full rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1011 Full or Half rate TCH channel. Half rate preferred, changes not allowed...
Preference between permitted speech versions for the respective channel
rates as indicated in octet 5, 5a ...
0001 1111 Full or Half rate TCH channel, changes not allowed ...
Preference between permitted speech versions as indicated in octet 5, 5a ...
0000 0000 SDCCH or Full rate TCH channel Bm or Half rate TCH channel Lm
0000 0001 SDCCH
0000 0010 SDCCH or Full rate TCH channel Bm Not
supported
0000 0011 SDCCH or Half rate TCH channel Lm Not
supported
0000 1000 Full rate TCH channel Bm Not supported
0000 1001 Half rate TCH channel Lm Not supported
0000 1010 Full or Half rate TCH, FR preferred, changes allowed Not supported
0000 1011 Full or Half rate TCH, HR preferred, changes allowed Not supported
0001 1010 Full or Half rate TCH, FR preferred, changes not allowed Not supported
0001 1011 Full or Half rate TCH, HR preferred, changes not allowed Not supported
765 4321
000 0001 GSM speech full rate version 1
001 0001 GSM speech full rate version 2
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
246
Ext : reserved for extension, set to value 0 (= no extension) for this message.
For non-transparent service bits 6-1 indicate the radio interface data rate;
65 4321
00 0000 12 kbits/s for TCH/HR
6 kbits/s for TCH/HR Not supported
01 0000 12 kbits/s
01 0001 6 kbits/s Not supported
Stored in order to be able to allocate the required channel. Use for the sending of the
"Channel Activation" message to the BTS.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
247
DEFINITION
This element contains the user data encryption information used to control any
encryption equipment at the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 1 0
Length (1 or 9)
Permitted Algorithms
Key
: :
: :
Key (continued)
Algorithm Identifier
The permitted algorithms octet is a bit map indicating the encryption algorithms from which
the BSS may select the algorithm to be used.
Bit No
1 No encryption
2 GSM A5/1
3 GSM A5/2
4 GSM A5/3 Not supported
5 GSM A5/4 Not supported
6 GSM A5/5 Not supported
7 GSM A5/6 Not supported
8 GSM A5/7 Not supported
A bit position encoded as 1 indicates that the BSS may use the encryption algorithm
represented by that bit position. A bit position encoded as 0 indicates that the BSS shall
not use the encryption algorithm represented by that bit position. A permitted algorithms
octet containing all bits encoded as 0 shall not be used.
The key shall be present if at least one of the A5 encryption algorithms is permitted. When
present, the MSC will send a key which shall be 8 octets long.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
248
Stored at the BSC in order to be able to give the information to the BTS (during internal
Handover for example, or when the BSC allocates a TCH).
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
249
DEFINITION
To provide the network with Information concerning the capabilities of the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 1 0 1
0 Revision 0 A5/1 RF power
level capab.
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
The BSC is non transparent to this parameter, in order to read the capabilities of the
attached MSs. This phase 2 format is always used by the BSC to decode this IE.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
250
DEFINITION :
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction as given by a MS supporting GSM phase 1.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
Revision Encryption RF power 3
level Algorithm Capability
0 0 0 0 SM. Frequency capability 4
cap
Octet 3
Bits 8 7 6
Revision level : 0 0 0 Reserved for phase 1.
All other values reserved
DCS1800 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
All other values reserved
DCS1900 : Bits 3 2 1
0 0 0 class 1
0 0 1 class 2
0 1 0 class 3
All other values reserved
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
251
Octet 4
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 321
FC Frequency Capability : 0 0 0 Band no 0
Other values reserved.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
252
DEFINITION
Defines certain attributes of the Mobile Station equipment in use on a particular
transaction.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0 1
Length 2
0 Revision 0 A5/1 RF power 3
spare level spare Capability
0 PS SS Screen. SM. 0 0 FC 4
spare Capa. Indicator cap spare spare
CM3 0 0 0 0 0 A5/3 A5/2 5
spare spare spare spare spare
Octet 3
Bits 76
Revision level : 00 Reserved for phase 1.
01 Used by phase 2 mobiles
All other values reserved
Bit 4
A5/1 : 0 algorithm A5/1 available
1 algorithm A5/1 not available.
Bits 321
RF Power capability :
GSM900 000 class 1
001 class 2
010 class 3
011 class 4
100 class 5
All other values reserved
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
253
Bits 65
SS Screening Indicator : 00
01
10
11
Bit 4
SM Capability : 0 short message capability not present
1 short message capability present
Bit 1
FC Frequency Capability : GSM900
0 The MS does not support the extension band
G1 in addition to the primary GSM band.
1 The MS does support the extension band G1.
DCS1800
0 Reserved for future use
Octet 5
Bit 8
CM3 Classmark 3 0 No additional MS capability
1 Additional MS capabilities are described in the
classmark 3 information element.
Bit 2
A5/3 algorithm supported 0 A5/3 not available
1 A5/3 available
Bit 1
A5/2 algorithm supported 0 A5/2 not available
1 A5/2 available
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
254
The BSC takes this information in order to have the MS power capability for the power
control and algorithm information. Default values are used for 'revision level', 'RF Power
Capability' and MS cipher capability if the BSC can not decode these fields (see reference
[25]).
Additional mobile info can be obtained by invoking the classmark interrogation procedure.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
255
DEFINITION :
Identification of a cell within the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 1 1
Length 2
spare Cell Identification 3
Discriminator
Cell Identification 4-10
Discriminator 0010:
4 CI value
5 CI value cont.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
256
MCC, MNC :
The BSC will use the cell identifier (serving) in order to identify if handover is synchronous
or asynchronous : If the serving cell identifier is incorrect (not belonging to the BSC or
unknown) then an asynchronous handover is performed.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
257
DEFINITION
Definition of the priority of the request for traffic channels only.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 1 0
Length
spare pci Priority level qa pvi
priority level:
6543
0 0 0 0 spare
0 0 0 1 priority level 1 = highest priority
0 0 1 0 priority level 2 = second highest priority
::::
1 1 1 0 priority level 14 = lowest priority
1 1 1 1 priority not used
if queuing is allowed (qa =1) and priority =1111 then lowest priority is assigned.
if queuing is allowed (qa =1) and priority =0000 then lowest priority is assigned.
- Taken into account in order to queue, if needed, the message. Only 'Pre-emption'
not allowed is used by the MSC.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
258
DEFINITION :
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
259
DEFINITION
This flag indicates if the DTX function in the BSS is to be disabled on a particular
radio channel.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 0 1
0 0 0 0 0 0 0 DTX
Flag
- in case of speech (full rate only), the DTX is sent to the BTS in the "CHANNEL
ACTIVATION" message.
- For Speech channel (full rate only), if not included, "DTX enabled" in downlink direction is
selected as default value.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
260
DEFINITION
Speech version being used by the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0 1
spare Speech version identifier 2
Speech version identifier is coded in the same way as the permitted speech version
identifier in the Channel type information element.
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
261
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 0 0
0 0 0 0 1 0 1 1
Length (value=3)
Channel spare Speech or data indicator
Type Channel Rate and type
0 0 0 0 1 0 1 0
Length (1 or 9)
Encryption Permitted Algorithms
Information Key
Key (continued)
Classmark Inf. 0 0 0 1 1 1 0 1
Type 1 0 Revision 0 A5/1 RF power
level capab.
OR
Classmark 0 0 0 1 0 0 1 0
Information Length (value=2)
Type 2 Revision Encrypt. RF power
level Algorithm Capability
(Phase 1 MS) 0 0 0 0 SM Freq.
Capa Capability
OR
0 0 0 1 0 0 1 0
Classmark Length=3
Information 0 Revision 0 A5/1 RF power
spare level spare Capability
Type 2 0 PS SS Screen. SM. 0 0 FC
spare Capa Indicator cap spare spare
(Phase 2 MS) CM3 0 0 0 0 0 A5/3 A5/2
spare spare spare spare spare
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
262
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5 or 3)
serving
option
/ I \
either: or: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0
LAC cont.
CI value
CI value cont.
0 0 0 0 0 1 1 0
Priority Length optional
spare pci Priority level qa pvi
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part) optional
Code (Low part) TS in use
Downlink 0 0 0 1 1 0 0 1
DTX Flag 0 0 0 0 0 0 0 DTX optional
Flag
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
263
Cell 0 0 0 0 0 1 0 1
Identifier Length (value = 8 or 5 or 3)
target
option
/ I \
either: or: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0
LAC cont.
CI value
CI value cont.
Speech 0 1 0 0 0 0 0 0
Version spare Speech version identifier optional
Ed 04 HANDOVER REQUEST
3BK 11202 0075 DSZZA
264
FUNCTION This message is sent from BSC to MSC and indicates that the request to
support an Handover at the target BSS can be supported by the BSS,
and also to which radio channel the MS should be directed.
FOLLOWING
EVENT Handover complete from the Clear command from the
MS. MSC T9113
Note This information field carries a radio interface "HANDOVER COMMAND" message
(1) This will only be sent if the channel type IE in the HANDOVER REQUEST indicated
either SDCCH/no preferences or TCH with a preference.
(2) This will only be included if the MSC indicates that more than one ciphering algorithm
is permitted. This possibility would have been indicated to the BSC in the Encryption
Information IE contained in the last received HANDOVER REQUEST or CIPHER
MODE COMMAND messages.
(3) Included at least when the speech version choice was done by the BSS.
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
265
DEFINITION
It is used to pass Layer 3 messages from the Air Interface to the MSC unchanged,
or from the MSC to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 1 1 1 1
Length 2
Layer 3 Information 3
: :
: :
N
This information element contains in that message the "Handover Command" message
which has to be sent to the MS.
The coding is the same as the "Handover Command" in the Air Interface.
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
266
DEFINITION
Description of the channel allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 0 0 1 1
spare Channel 2
Channel
Bit 4321
0001 SDCCH
1000 Full rate TCH
1001 Half rate TCH
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
267
DEFINITION
Description of the encryption algorithm allocated to the MS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 1 1 0 0 1
Algorithm Identifier 2
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
268
DEFINITION
Speech version being used by the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0 1
spare Speech version identifier 2
Speech version identifier is coded in the same way as the permitted speech version
identifier in the Channel type information element.
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
269
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 1 0
0 0 0 1 0 1 1 1
Layer Length
3 Layer 3 Information
INFO = Handover Command
Coded as on the radio interface
Chosen 0 0 1 0 0 0 0 1
Channel spare Channel optional
Chosen Encry. 0 0 1 0 1 1 0 0
Algorithm Algorithm Identifier optional
Speech 0 1 0 0 0 0 0 0
Version spare Speech version identifier optional
Ed 04 HANDOVER REQUEST
ACKNOWLEDGE
3BK 11202 0075 DSZZA
270
HANDOVER REQUIRED
NAME HANDOVER REQUIRED
FUNCTION This message is sent from the BSC to indicate that for a given MS which
already has a dedicated radio resource assigned, a handover is required
for the reason given by the cause element
FOLLOWING
EVENT Handover Request Handover Required T7
(optional) Reject (optional) T_HO_RE
Q_LOST
(*) n <= 3
(1) Included when the channel mode is speech, and only in this case.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
271
DEFINITION :
To indicate the reason for a particular event to have occurred.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 1 0 0
Length
0 Cause
The BSC gives in this parameter the reason of the Handover requested to the MSC.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
272
DEFINITION :
To request that the MSC responds to a handover required message, in particular if
handover cannot be performed, to respond with HANDOVER REQUIRED REJECT.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 1
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
273
DEFINITION :
This element uniquely identifies cells within a BSS and is of variable length N. P is
the number of elements within the list and the range for P is 1 to 16 (included).
BIT DESCRIPTION
Cell 0 0 0 1 1 0 1 0
Identifier Length (value = 1+Px7) or 1+Px4
spare Cell Identif.Discriminator 3
Cell 1, format depends on Cell Id Discriminator 4 to 7 4
octets.
.. .. .. ..
Cell P, format depends on Cell Id Discriminator 4 to 7 N
octets.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
274
Length = 1 + 7 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CI value 9
CI value cont. 10
CELL P
MCC digit 2 MCC digit 1 N-6
1 1 1 1 MCC digit 3 N-5
MNC digit 2 MNC digit 1 N-4
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
275
Length = 1 + 4 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CI value 6
CI value cont. 7
CELL P
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
MCC, MNC :
The MSC requires the information from a specific cell controlled by the BSC. This info
element is included even in case of mono-cell configuration.
The choice between the use of cell discriminator 0 or 1 depends on the value of a BSS-
O&M parameter.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
276
DEFINITION
Speech version being used by the BSS.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 0 0 0 0 1
spare Speech version identifier 2
Speech version identifier is coded in the same way as the permitted speech version
identifier in the Channel type information element.
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
277
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 0 0 0 1
0 0 0 0 0 1 0 0
Cause Length
0 Cause
Resp. Req 0 0 0 1 1 0 1 1 optional
0 0 0 1 1 0 1 0
Length (value = 1+Px7) or 1+Px4
Cell
Identifier option
list / \
either: or:
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
MCC digit 2 MCC digit 1 LAC
1 1 1 1 MCC digit 3 LAC cont.
MNC digit 2 MNC digit 1 CI value
LAC CI value cont.
LAC cont.
CI value
CI value cont. CELL 1
Speech 0 1 0 0 0 0 0 0
Version spare Speech version identifier optional
Ed 04 HANDOVER REQUIRED
3BK 11202 0075 DSZZA
278
CHANNEL/ SCCP
USAGE Connection
GSM-REF 08.08
FUNCTION This message is sent from the MSC to the BSC to Request the start of a
trace.
FOLLOWING
EVENT
(1) Not used by the BSC but if received, they are copied to the trace record..
DEFINITION
Trace type.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 0 0 1 0 1
pi 0 BSS rec. typ MSC rec typ Invok. event
Trace type
Bit 'pi' is only used : when set to 1, a priority indication is given to the OMC-R when the
trace record is completed.
DEFINITION
A variable length element indicating the identity of the entity which initiated the
trace.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 0 1 1 0 1
Length 2
Entity identity 3-22
DEFINITION
Reference used to identify the connection being traced.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 0 1 1 1 1
Trace Reference 2-3
DEFINITION
A potentially variable length element indicating a particular transaction within a trace.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 1 0 0 0 1
Length 2
Transaction number 3-4
DEFINITION
A variable length element.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 1 0 0 1 1
Length 2
Mobile Identity 3-n
Octet 3-n contain either the IMSI or IMEI as coded in TS GSM 04.08, not including GSM
04.08 element identifier or GSM 04.08 octet length value.
DEFINITION
A variable length element indicating the destination OMC to which trace
information is to be sent.
BIT DESCRIPTION
8 7 6 5 4 3 2 1 Octet
0 0 1 0 1 0 1 0 1
Length 2
OMC Identity 3-32
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 0 1 1 0 1 1 0
Trace 0 0 1 0 0 1 0 1
Type Trace type
Trace 0 0 1 0 0 1 1 1
Reference Trace
Reference
OVERLOAD
Ed 04 OVERLOAD
3BK 11202 0075 DSZZA
288
PAGING
NAME PAGING
FUNCTION This message is sent from MSC to BSC and contains sufficient
information to allow the paging message to be transmitted at the correct
time
FOLLOWING
EVENT BSC sent "Paging" command
to BTS
(1) If the cell identifier is not present, incorrect then paging will be sent on all cells of the
BSC.
If this IE is missing , it is not treated as an error in this release.
(2) Not supported.
Ed 04 PAGING
3BK 11202 0075 DSZZA
289
DEFINITION
Value of IMSI
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 0 0 1
Length 2
Id digit 1 OEI Type of Id 3
Id digit 3 Id digit 2 4
... ... ... ...
Id digit p+1 Id digit p N
0 0 0 0 1 0 0 0 1
Length 2
0 0 0 1 0 0 0 1 3
0 1 1 0 1 0 0 0 4
0 1 0 0 0 1 0 1 5
1 1 1 1 0 0 1 1 6
Ed 04 PAGING
3BK 11202 0075 DSZZA
290
DEFINITION
Value of TMSI
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 1 0 0 1 1
Length (value = 4) 2
TMSI value 3
TMSI value contd. 4
TMSI value contd. 5
TMSI value contd. 6
Bit 8 of octet 3 is the most significant bit, and bit 1 of octet 6 is the least significant bit.
If the length of TMSI is less 4 octets, the MSC should fill the field with zeroes in front of the
MSB.
Ed 04 PAGING
3BK 11202 0075 DSZZA
291
DEFINITION
Identifies a list of cells within a BSS. Let P be the number of cells in the list.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 1 1 0 1 0 1
Length 2
spare Cell Identif.Discriminator 3
Cell 1, format depends on Cell Id Discriminator 2 to 7 4
octets.
.. .. .. ..
Cell P, format depends on Cell Id Discriminator 2 to 7 P
octets.
Ed 04 PAGING
3BK 11202 0075 DSZZA
292
Length = 1 + 7 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CI value 9
CI value cont. 10
CELL P
MCC digit 2 MCC digit 1 N-6
1 1 1 1 MCC digit 3 N-5
MNC digit 2 MNC digit 1 N_4
LAC N_3
LAC cont. N_2
CI value N_1
CI value cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
293
Length = 1 + 4 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CI value 6
CI value cont. 7
CELL P
LAC N-3
LAC cont. N-2
CI value N-1
CI value cont. N
Length = 1 + 2 x P
Octets 4 to N:
CELL 1
CI value 4
CI value cont. 5
CELL P
CI value N-1
CI value cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
294
Length = 1
Octets 4 to N: NONE
Length = 1 + 5 x P
Octets 4 to N:
CELL 1
MCC digit 2 MCC digit 1 4
1 1 1 1 MCC digit 3 5
MNC digit 2 MNC digit 1 6
LAC 7
LAC cont. 8
CELL P
MCC digit 2 MCC digit 1 N-4
1 1 1 1 MCC digit 3 N-3
MNC digit 2 MNC digit 1 N-2
LAC N-1
LAC cont. N
Ed 04 PAGING
3BK 11202 0075 DSZZA
295
Length = 1 + 2 x P
Octets 4 to N:
CELL 1
LAC 4
LAC cont. 5
CELL P
LAC N-1
LAC cont. N
Length = 1
Octets 4 to N: NONE
MCC, MNC :
Values (1,4,5,6) are accepted by the BSS. Values (2,3) should not be used by the MSC:
value (3) does not make sense for paging, and value (2) is not sufficient information.
However, in those two last cases paging will be done to all cells of the BSS.
Ed 04 PAGING
3BK 11202 0075 DSZZA
296
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 1 0 0 1 0
0 0 0 0 1 0 0 0
Length
IMSI Id digit 1 OEI 0 0 1
Id digit 3 Id digit 2
.. .. .. ..
Id digit p+1 Id digit P
0 0 0 0 1 0 0 1
Length (value = 4)
TMSI TMSI value
(optional) TMSI value contd.
TMSI value contd.
TMSI value contd.
0 0 0 1 1 0 1 0
Length
Cell Cell Identif.Discriminator
Identifier Cell 1, format depends on Cell Id Discriminator 2 to 7
octets.
List .. .. .. ..
Cell P, format depends on Cell Id Discriminator 2 to 7
octets.
Ed 04 PAGING
3BK 11202 0075 DSZZA
297
QUEUING INDICATION
Ed 04 QUEUING INDICATION
3BK 11202 0075 DSZZA
298
RESET
Same format as phase 1
Ed 04 RESET
3BK 11202 0075 DSZZA
299
RESET ACKNOWLEDGE
Ed 04 RESET ACKNOWLEDGE
3BK 11202 0075 DSZZA
300
RESET CIRCUIT
Ed 04 RESET CIRCUIT
3BK 11202 0075 DSZZA
301
UNBLOCK
Ed 04 UNBLOCK
3BK 11202 0075 DSZZA
304
UNBLOCKING ACKNOWLEDGE
Ed 04 UNBLOCKING ACKNOWLEDGE
3BK 11202 0075 DSZZA
305
UNEQUIPPED CIRCUIT
NAME UNEQUIPPED CIRCUIT
FUNCTION This message is sent from the BSS to the MSC or vice versa to indicate
to the partner entity that it is utilising one or several circuit identity codes
which are unknown and which therefore should be locally blocked
immediately and taken out of service.
This message is sent as a connectionless SCCP message.
FOLLOWING
EVENT
Ed 04 UNEQUIPPED CIRCUIT
3BK 11202 0075 DSZZA
306
DEFINITION
Defines the terrestrial channel over which the call will pass.
BIT DESCRIPTION
8 7 6 5 4 3 2 1
0 0 0 0 0 0 0 1
PCM multiplex in use (high part)
(Low part) TS in use
PCM Multiplex )
) defines the terrestrial channel
TS in use )
Ed 04 UNEQUIPPED CIRCUIT
3BK 11202 0075 DSZZA
307
GENERAL DESCRIPTION
8 7 6 5 4 3 2 1
0 1 0 0 1 0 0 0
Circuit 0 0 0 0 0 0 0 1
Identity PCM multiplex in use (high part)
Code (Low part) TS in use
Ed 04 UNEQUIPPED CIRCUIT
3BK 11202 0075 DSZZA