Professional Documents
Culture Documents
Draft For Public Comment: Latest Date For Receipt of Comments: 30 JUNE 2009
Draft For Public Comment: Latest Date For Receipt of Comments: 30 JUNE 2009
Version 8.0
DPC: 09/30181191 DC
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
Head Office
389 Chiswick High Road Date: 29 April 2009
London W4 4AL
Telephone: +44(0)20 8996 9000
Origin: National
Fax: +44(0)20 8996 7001
Latest date for receipt of comments: 30 JUNE 2009 Project no.: 2008/01291
Responsible committee: ACE/61 Metallic materials for aerospace purposes
Title: Draft BS 2B 23 Specification for copper-aluminium-nickel-iron alloy rods, sections, forging stock and
forgings
Supersession information: If this document is published as a standard, the UK implementation of it will supersede
BS B 23 : 1991 and partially supersede NONE. If you are aware of a current national standard which may be
affected, please notify the secretary (contact details below).
WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD.
THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
This draft is issued to allow comments from interested parties; all comments will be given consideration prior to
publication. No acknowledgement will normally be sent. See overleaf for information on commenting.
No copying is allowed, in any form, without prior written permission from BSI except as permitted under the
Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes.
Electronic circulation is limited to dissemination by e-mail within such an organization by committee members.
Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email
cservices@bsigroup.com. British, International and foreign standards are also available from BSI Customer Services.
Information on the co-operating organizations represented on the committees referenced above may be obtained
from the responsible committee secretary.
Cross-references
The British Standards which implement International or European publications referred to in this draft may be found
via the British Standards Online Service on the BSI web site http://www.bsigroup.com.
Responsible Content Developer: Miss Laura Cooper Direct tel: 020 8996 7691
E-mail: laura.cooper@bsigroup.com
a
Introduction
Your comments on this draft are invited and will assist in the preparation of the resulting British Standard. If no
comments are received to the contrary, this draft may be implemented unchanged as a British Standard.
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
Please note that this is a draft and not a typeset document. Editorial comments are welcome, but you are advised not
to comment on detailed matters of typography and layout.
Submission of Comments
The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the
responsible BSI committee.
• This draft British Standard is available for review and comment online via the BSI British Standards Draft Review
system (DRS) as http://drafts.bsigroup.com. Registration is free and takes less than a minute.
• Once you have registered on the DRS you will be able to review all current draft British Standards of national
origin and submit comments on them. You will also be able to see comments made on current draft standards by
other interested parties.
• When submitting comments on a draft you will be asked to provide both a comment (i.e. justification for a
change) and a proposed change.
• All comments will be checked by a moderator before they are made public on the site. This is to ensure that
improper language or marketing is not placed on the site – the technical content of your comment will not be
judged or modified; similarly, your grammar or spelling will not be corrected. You will receive acknowledgement
by email of all comments you submit via the DRS.
• A link to the DRS, or to a specific draft hosted on the system, may be distributed to other interested parties so
that they may register and submit comments. It is not necessary to purchase a copy of the draft in order to review
or comment on it; however, copies of this draft may be purchased from BSI, Tel: +44(0)20 8996 9001 or
email: cservices@bsigroup.com. Drafts and standards are also available in PDF format for immediate download
from the BSI Shop: http://www.bsigroup.com/shop.
b
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
BS 2B 23:2009
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
Specification for
Copper-aluminium-nickel-iron alloy
rods, sections, forging stock and
forgings
i
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
ii
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Contents
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
Foreword ii
1 Scope 1
2 Normative references 1
3 Technical requirements 1
Bibliography 6
List of tables
Table 1 – Technical requirements for Cu-Al-Fe-Ni alloys bars, rods and sections 2
Table 2 – Technical requirements for Cu-Al-Fe-Ni alloy forging stock and forgings 4
Summary of pages
This document comprises a front cover, an inside front cover, pages i to ii, pages 1 to x, an
inside back cover and a back cover.
i
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Foreword
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
Publishing information
This British Standard is published by BSI and came into effect on XX Month 2009. It was
prepared by Panel ACE/61/-/16, Copper and miscellaneous alloys, under the authority of
Technical Committee ACE/61, Metallic materials for aerospace purposes. A list of
organizations represented on this committee can be obtained on request to its secretary.
Supersession
This British Standard supersedes BS B 23:1991, which is withdrawn.
Information about this document
This is a full revision of BS B 23 and introduces the following principal changes:
a) symbols and units in the tables are to be interpreted in accordance with BS ISO 31-0 and
BS ISO 1000;
b) requirements are stated in tabular format in accordance with prEN 4500-1;
c) for dimensional inspection of bars, rods and sections (Table 1-line 96), withdrawn
BS 2874 has been replaced by BS EN 12163;
d) for dimensional inspection of forging stock (Table 2-line 96), withdrawn BS 2872 has
been replaced by BS EN 12165.
Hazard warnings
WARNING. This British Standard calls for the use of substances and/or procedures that can
be injurious to health if adequate precautions are not taken. It refers only to technical
suitability and does not absolve the user from legal obligations relating to health and safety at
any stage.
ii
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
1 Scope
This British Standard specifies the inspection and testing procedures, chemical composition, heat
treatment and mechanical properties for a copper-aluminium-nickel-iron alloy supplied in the form of
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
BS B 100, Procedure for inspection, testing and acceptance of wrought copper alloys
BS EN 12163, Copper and copper alloys — Rod for general purposes
BS EN 12165, Copper and copper alloys — Wrought and unwrought forging stock
BS ISO 31-0, Quantities and units — Part 0: General principles
BS ISO 1000, SI units and recommendations for the use of their multiples and of certain other units
3 Technical requirements
3.1 Material to this standard shall conform to the technical requirements specified in Table 1 for bars,
rods and sections and Table 2 for forging stock and forgings. All material supplied shall conform to the
requirements appropriate to its condition and dimensions as specified in the standards given in lines 5
and 96 of Table 1 or Table 2.
3.2 Symbols and units in the tables shall be interpreted in accordance with BS ISO 31-0 and BS ISO
1000.
NOTE The format and symbols used in Table 1 and Table 2 are derived from prEN 4500-1.
1
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Table 1 – Technical requirements for Cu-Al-Fe-Ni alloys bars, rods and sections
1 Material designation CuAl10Fe5Ni5
2 Chemical Element Al Ni Fe Sn Pb Mn Si Zn Total impurities Cu
composition
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
4.2 Method of production Extruded and/or rolled, extruded and drawn, rolled and drawn or forged
4.3 Limit dimension(s) mm —
Heat treatment —
Characteristics
8.1 Test sample(s) See Section 2 of BS B 100.
8.2 Test piece(s) See Section 2 of BS B 100.
8.3 Heat treatment Use condition
9 Dimensions concerned mm 6 a or D 18 18 a or D 80 a or D 80
Thickness of cladding
10 % —
on each face
11 Direction of test piece L L L
15 Elongation A % 10 12 12
Reduction of
16 Z % —
area
2
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Table 1 — Technical requirements for Cu-Al-Fe-Ni alloys bars, rods and sections (continued)
44 External defects — See Section 2 of BS B 100.
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
3
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Table 2 – Technical requirements for Cu-Al-Fe-Ni alloy forging stock and forgings
1 Material designation CuAl10Fe5Ni5
2 Chemical Element Al Ni Fe Sn Pb Mn Si Zn Total impurities Cu
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
composition
% Min 8.5 4.0 4.0 — — — — — —
Base
Max 11.0 5.5 5.5 0.10 0.05 0.50 0.2 0.40 0.5 (excluding Mn)
3 Method of melting —
Heat treatment At the option of the manufacturer At the option of the manufacturer
6.2 Delivery condition code U U
7 Use condition Delivery condition Delivery condition
Heat treatment — —
Characteristics
8.1 Test sample(s) See Section 3 of BS B 100. See Section 4 of BS B 100.
8.2 Test piece(s) See Section 3 of BS B 100. See Section 4 of BS B 100.
8.3 Heat treatment Use condition Use condition
9 Dimensions concerned mm — —
Thickness of cladding
10 % —
on each face
11 Direction of test piece L L
15 Elongation A % 14 14
Reduction of
16 Z % — —
area
4
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Table 2 — Technical requirements for Cu-Al-Fe-Ni alloy forging stock and forgings (continued)
Forging stock Forging
44 External defects — See Section 3 of BS B 100. See Section 4 of BS B 100.
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
5
WARNING. THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH
STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 JUNE 2009.
Bibliography
Standards publications
For dated references, only the edition cited applies. For undated references, the latest edition of the
Licensed Copy: x x, The University of Sheffield, 23/06/2009 11:42, Uncontrolled Copy, (c) BSI
1)
Published as ASD-STAN Prestandard at the date of publication of this standard.
6