Professional Documents
Culture Documents
D100025X012 PDF
D100025X012 PDF
51.1:EZ
August 2002 EZ Valve
FGM gaskets
www.Fisher.com
Product Bulletin
51.1:EZ
EZ Valve August 2002
Contents Features
Ordering Information . . . . . . . . . . . . . . . . . . 18
Application Flexibility—Low-flow
requirements can be satisfied with standard
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
restricted-capacity trim or with Micro-Form,
Micro-Flute, or Micro-Flow valve plugs. If flow
Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 requirements change, the valve can be converted to
full-sized trim.
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2
Product Bulletin
51.1:EZ
August 2002 EZ Valve
35A7592-E
W7027-2 / IL
3
Product Bulletin
51.1:EZ
EZ Valve August 2002
ANTI-ROTATOR
ENVIRO-SEAL packing systems, available with PIN
BELLOWS
VALVE PLUG
CONNECTION
VALVE PLUG
ENVIRO-SEAL, HIGH-SEAL Features
Excellent Sealing Capabilities—The patented
packing system provides excellent sealing, guiding,
and transmission of loading force. The superior
sealing of the ENVIRO-SEAL system can control
emissions to below the EPA (Environmental
Protection Agency) minimum of 500 ppm (parts per
W5800-2*A/IL
million).
Figure 3. Design EZ Valve with ENVIRO-SEAL Bellows
Seal Bonnet
Improved Service Life—ENVIRO-SEAL and
HIGH-SEAL system design, very smooth stem
surface, and live-loading combine to give you longer Adaptable to Many Applications—
service with very low maintenance. The external ENVIRO-SEAL systems are available with PTFE or
live-loading provides a constant load over the life of graphite packing for 9.5 through 31.8 mm (3/8
the packing material, which greatly reduces or through 1-1/4 inch) diameter valve stems.
eliminates your need for packing box adjustment and HIGH-SEAL systems with graphite packing are
maintenance. available for 9.5 through 50.8 mm (3/8 through
2-inch) diameter valve stems. Standard
ENVIRO-SEAL packing systems can be used in
Easy Installation in Existing Valves—All vacuum service with packing rings in standard
parts needed to install the systems in existing valves orientation. It is not necessary to reverse the
are available in a convenient kit. ENVIRO-SEAL PTFE packing rings.
4
Product Bulletin
51.1:EZ
August 2002 EZ Valve
PACKING PACKING
BOX BOX
STUDS STUD
SPRINGS
SPRINGS
ANTI–
EXTRUSION
PACKING PACKING
RING
RING
FOLLOWER
VALVE
LANTERN VALVE BONNET
BONNET
RING
W5805–5 / IL
W5803–3 / IL
PACKING
BOX
STUD
SPRING
FOLLOWER
PACKING
W5801–3 / IL
W7018 / IL
5
Product Bulletin
51.1:EZ
EZ Valve August 2002
TEMPERATURE, C
–18 0 30 60 90 120 150 177 204
1000 69
60
800
600 40
400
1 20
200
0
0 50 100 150 200 250 300 350 400
TEMPERATURE, F
NOTE:
1 MAXIMUM TEMPERATURE FOR PTFE DISK IN DESIGN EZ
VALVES WITH ALL METAL TRIM PARTS EXCEPT N05500 (K-MONEL)
AND ALLOY 6B. MAXIMUM TEMPERATURE FOR DESIGN EZ PTFE
DISK WITH ALLOY 6B TRIM PARTS IS 177C (350F) AND WITH
N05500 TRIM PARTS IS 204C (400F).
A6570/IL
Micro-Flute Valve Plugs for Minimum mm (3/8 inch) actuator-stem connection, and 6.4
mm (1/4 inch) seat ring port diameter. These plugs
Leakage have the same flow coefficients as standard
Micro-Flute plugs. Standard seat rings are used.
The Design EZ valve can be furnished with PTFE
composition-seat Micro-Flute valve plugs for Class
VI shutoff per ANSI/FCI 70-2 and IEC 60534-4. The valve plugs have a screwed retainer that holds
the seat disk and valve plug tip to the valve stem.
These valve plugs are available on 1/2 to 2-inch See figure 5 for pressure and temperature
valves with a 9.5 mm (3/8 inch) stem diameter, 9.5 information.
6
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 3. Material Cross Reference
Common/Tradename Common/Tradename
Standard Designation Standard Designation
Other Designation Other Designation
CB7Cu-1 17-4 PH Stainless Steel R30006 Alloy 6, Cast
CF8M 316 Stainless Steel S17400 17-4 PH Stainless Steel
CoCr-A Alloy 6 Hardfacing S31600 316 Stainless Steel
WC9 Chrome-Moly Steel S31603 316L Stainless Steel
N04400 Monel 400 S41600 416 Stainless Steel
N05500 K-Monel, Alloy K500 WCC WCC Steel
M35-1 Monel Alloy 6B Alloy 6, Wrought
NOTES:
1 ALSO APPLIES TO TRIMS 101C, 127C,
137C, 151C, 153C, 154C, AND 158C.
2 ALSO APPLIES TO TRIMS 104C, 128C, PTFE SEATING WITH
129C, 139C, 152C, 155C, 156C, AND 157C. ALL VALVE BODY MATERIALS
(–29C [–20F] WITH WCC
VALVE BODY)
A6415/IL
7
Product Bulletin
51.1:EZ
EZ Valve August 2002
Table 4. Typical Combinations of Metal Trim Parts for Equal Percentage (Including Micro-Form), Linear, and Quick Opening Valve Plugs
Disk Seat and
Trim Valve Valve Seat Seat Ring Retainer for Guide
Designation Plug Stem Ring Retainer Optional PTFE-Seat Bushing
Construction
S41600 CB7Cu-1 S17400
S31600 S41600
101(1) (416 stainless steel) (17-4 PH S41600 (17-4 PH
(316 stainless steel) hardened
hardened stainless steel) stainless steel)
S31600
104 S31600 S31600 CB7Cu-1 S31600 S17400
(316 stainless steel)
120 N05500 (K-Monel) N05500 N05500 M35-1 (Monel) N05500 N05500
S31600 w/CoCr-A
S31600 CF8M
127 (alloy 6) S31600 --- Alloy 6B
w/CoCr-A seat (316 stainless steel)
seat & guide
S31600 S31600
128 S31600 CF8M --- Alloy 6B
w/CoCr-A seat w/CoCr-A seat
129(2) S31600 S31600 S31600 CF8M S31600 Alloy 6B
S31600
S31600
137 w/CoCr-A S31600 CB7Cu-1 --- S17400
w/CoCr-A seat
seat & guide
S31600 S31600
139 S31600 CB7Cu-1 --- S17400
w/CoCr-A seat w/CoCr-A seat
1. Standard trim for cast iron, WCC, and WC9 valve bodies, except Micro-Flow and Micro-Flute.
2. Standard trim for CF8M valve body.
Table 5. Typical Combinations of Metal Trim Parts for Micro-Flute and Micro-Flow Valve Plugs (These Constructions Do Not Use
Guide Bushing)
Disk Seat and
Trim Valve Valve Seat Seat Ring Retainer for
Designation Plug Stem Ring Retainer Optional PTFE-Seat
Construction(1)
S41600
S31600 CB7Cu-1
151 (416 stainless steel) S41600 hardened ---
(316 stainless steel) (17-4 PH stainless steel)
hardened
S31600
(316 stainless steel)
152(2) S31600 S31600 CB7Cu-1 S31600
w/CoCr-A (alloy 6)
seat, R30006 tip
153 N05500 (K-Monel) N05500 N05500 M35-1 (Monel) N05500
S31600 w/CoCr-A S31600 CF8M
154 S31600 ---
seat, R30006 tip w/CoCr-A seat & bore (316 stainless steel)
S31600 w/CoCr-A S31600
155 S31600 CF8M ---
seat, R30006 tip w/CoCr-A seat(3)
S31600 w/CoCr-A
156 S31600 S31600 CF8M S31600
seat, R30006 tip
S31600 w/CoCr-A S31600
157 S31600 CB7Cu-1 ---
seat, R30006 tip w/CoCr-A seat(3)
S31600 w/CoCr-A S31600
158 S31600 CB7Cu-1 ---
seat, R30006 tip w/CoCr-A seat & bore
1. Micro-Flute constructions.
2. Standard trim for Micro-Flow and Micro-Flute constructions in cast iron, WCC, CF8M, and WC9 valve bodies.
3. Micro-Flute and Micro-Flow valve plugs have a CoCr-A seat and R30006 tip, but are not recommended for erosive service without the additional use of CoCr-A on the seat and bore
of the seat ring.
8
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 6. Construction Materials and Temperature Limits
TEMPERATURE
PART
MATERIAL CAPABILITIES
C F
Cast iron valve body Cap screws Steel SAE Grade 5 –29 232(1) –20 450(1)
Body-to-
Studs Steel SA-193-B7
bonnet WCC steel body –29 427 –20 800
bolting. Nuts Steel SA-194-2H (lubricated)
See table Studs Steel SA-193-B7 (standard)
17 for –48 427 –55 800
Nuts Steel SA-194-2H (standard)
NACE
bolting CF8M (316 stainless Studs 304 stainless steel SA-320-B8
–198 38 –325 100
materials steel) body Nuts 304 stainless steel SA-194-8
and Studs 316 stainless steel SA-193-B8M (strain hardened)
temperatures –198 427 –325 800
Nuts 316 stainless steel SA-194-8M (lubricated)
Seat disk (optional) PTFE –73 204 –100 400
Bonnet and S31600 (316 stainless steel)/graphite(2) –198 593(4) –325 1100(4)
seat ring
gasket PTFE-coated N04400 (Monel) (optional for trim 120) –73 149 –100 300
N04400/composition (standard for trims 120 & 153) –73 232 –100 450
Spiral wound
N04400/PTFE (optional for trims 120 & 153) –73 149 –100 300
gaskets
N06600 (Inconel)/graphite (FGM) standard –198 593(4) –325 1100(4)
These materials not
S31600
limiting factors
Shim
These materials not
N04400 (standard for trims 120 & 153)
limiting factors
Packing flange studs and nuts when
S31600 –198 593 –325 1100
used with standard bonnet
Packing
(temperatures
PTFE V-ring –40 232 –40 450
shown are
material PTFE/composition –73 232 –100 450
temperature
capabilities).
See table 8 Graphite ribbon/filament –198 538(5) –325 1000(5)
for proper
bonnet Graphite ribbon for high-temperature oxidizing service –198 649 –325 1200
selection
Packing S31600(2) –198 593 –325 1100
follower N04400 (optional for trims 120 & 153) –198 482 –325 900
Packing spring S31600 –198 593 –325 1100
Lantern ring S31600(3) –198 593 –325 1100
(for double
packing) N04400 (standard for trims 120 & 153) –198 482 –325 900
Packing box S31600(3) –198 593 –325 1100
ring N04400 –198 482 –325 900
1. Temperature limit for bodies with screwed end connections is 208C (406F).
2. Standard for all trim.
3. Standard for all trim except for trim 120 and 153.
4. Except 427C (800F) for oxidizing service.
5. Except 371C (700F) for oxidizing service.
9
Product Bulletin
51.1:EZ
EZ Valve August 2002
10
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 7. Valve Body/Trim Temperature Capabilities for Metal Trim Parts (Continued)
TEMPERATURE CAPABILITIES
Trim for Equal Percentage
Trim for Micro-Flute and
VALVE BODY VALVE BODY SIZE, (Including Micro-Form), Linear,
Micro-Flow Valve Plugs
MATERIAL INCHES and Quick Opening Valve Plugs
Trim C F Trim C F
Designation Min Max Min Max Designation Min Min Min Max
101 –29 216 –20 420 --- --- --- --- ---
104, 139 –101 227(1) –150 440(1) --- --- --- --- ---
120 –198 316 –325 600 --- --- --- --- ---
3
87, 127 –198 377 –325 700 --- --- --- --- ---
85, 86, 128, 129 –198 377(1) –325 700(1) --- --- --- --- ---
CF8M 137 –101 227 –150 440 --- --- --- --- ---
(316 stainless steel) 101 –29 177 –20 350 --- --- --- --- ---
104, 139 –101 182(1) –100 360(1) --- --- --- --- ---
120 –198 316 –100 600 --- --- --- --- ---
4
87, 127 –198 371 –100 700 --- --- --- --- ---
85, 86, 128, 129 –198 371(1) –100 700(1) --- --- --- --- ---
137 –101 182 –100 360 --- --- --- --- ---
101 –29 427 –20 800 151 –29 –29 –20 600
104 –29 427(1) –20 800(1) 152 –29 –29 –20 300
120 –29 316 –20 600 153 –29 –29 –20 600
87, 127 –29 260 –20 500 154 –29 –29 –20 1050(2)
1/2, 3/4, 1, 1-1/2, or 2
86, 128 –29 260(1) –20 500(1) --- --- --- --- ---
85, 129 –29 260(1) –20 500(1) 156 –29 –29 –20 300
137 –29 427 –20 800 158 –29 –29 –20 800(1)
139 –29 427(1) –20 800(1) 157 –29 –29 –20 300
101 –29 427 –20 800 --- --- --- --- ---
WC9 chrome moly 104, 139 –29 371(1) –20 700(1) --- --- --- --- ---
steel 120 –29 316 –20 600 --- --- --- --- ---
3
87, 127 –29 343 –20 650 --- --- --- --- ---
85, 86, 128, 129 –29 343(1) –20 650(1) --- --- --- --- ---
137 –29 371 –20 700 --- --- --- --- ---
101 –29 427 –20 800 --- --- --- --- ---
104, 139 –29 371(1) –20 700(1) --- --- --- --- ---
120 –29 316 –20 600 --- --- --- --- ---
4
87, 127 –29 316 –20 450 --- --- --- --- ---
85, 86, 128, 129 –29 232(1) –20 450(1) --- --- --- --- ---
137 –29 371 –20 700 --- --- --- --- ---
1. With non-lubricating fluids, temperature is limited to 149C (300F).
2. For 2-inch valve body, maximum temperature is 466C (870F).
11
Product Bulletin
51.1:EZ
EZ Valve August 2002
Table 9. Maximum Allowable Pressure Drops per Trim Designation for Equal Percentage (Including Micro-Form), Linear, and Quick
Opening Valve Plugs
SHUTOFF FLOWING
TRIM VALVE VALVE SEAT SEAT RING GUIDE PRESSURE PRESSURE
DESIGNATION PLUG STEM RING RETAINER BUSHING DROP DROP
Bar Psig Bar Psig
S41600 CB7Cu-1 S17400
S31600 S41600
101 (416 stainless steel) (17-4 PH (17-4 PH 103 1500 103 1500
(316 stainless steel) hardened
hardened stainless steel) stainless steel)
S31600
104 S31600 S31600 CB7Cu-1 S17400 21 300 103 1500
(316 stainless steel)
120 N05500 (K-Monel) N05500 N05500 M35-1 (Monel) N05500 55 800 103 1500
S31600 w/CoCr-A
S31600 CF8M
87, 127 (alloy 6) S31600 Alloy 6B 103 1500 103 1500
w/CoCr-A seat (316 stainless steel)
seat & guide
S31600 S31600
86, 128 S31600 CF8M Alloy 6B 103 1500 103 1500
w/CoCr-A seat w/CoCr-A seat
85, 129 S31600 S31600 S31600 CF8M Alloy 6B 21 300 103 1500
S31600
S31600
137 w/CoCr-A S31600 CB7Cu-1 S17400 103 1500 103 1500
w/CoCr-A seat
seat & guide
S31600 S31600
139 S31600 CB7Cu-1 S17400 103 1500 103 1500
w/CoCr-A seat w/CoCr-A seat
12
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 10. Maximum Allowable Pressure Drops per Trim Designation for Micro-Flute and Micro-Flow Valve Plugs
SHUTOFF FLOWING
TRIM VALVE VALVE SEAT SEAT RING PRESSURE PRESSURE
DESIGNATION PLUG STEM RING RETAINER DROP DROP
Bar Psig Bar Psig
S41600
S31600 CB7Cu-1
151 (416 stainless steel) S41600 hardened 103 1500 103 1500
(316 stainless steel) (17-4 PH stainless steel)
hardened
S31600
(316 stainless steel)
152 S31600 S31600 CB7Cu-1 21 300 103 1500
w/CoCr-A (alloy 6)
seat, R30006 tip
153 N05500 (K-Monel) N05500 N05500 M35-1 (Monel) 55 800 103 1500
S31600 w/CoCr-A S31600 CF8M
87, 154 S31600 103 1500 103 1500
seat, R30006 tip w/CoCr-A seat & bore (316 stainless steel)
S31600 w/CoCr-A S31600
86, 155 S31600 CF8M 103 1500 103 1500
seat, R30006 tip w/CoCr-A seat
S31600 w/CoCr-A
85, 156 S31600 S31600 CF8M 21 300 103 1500
seat, R30006 tip
S31600 w/CoCr-A S31600
157 S31600 CB7Cu-1 103 1500 103 1500
seat, R30006 tip w/CoCr-A seat
S31600 w/CoCr-A S31600
158 S31600 CB7Cu-1 103 1500 103 1500
seat, R30006 tip w/CoCr-A seat & bore
13
Product Bulletin
51.1:EZ
EZ Valve August 2002
Table 12. Maximum Allowable Pressure Drops (Flow Up Only)(1) for Gasket Materials (1/2 through 1-1/2 Inch Valve Size)
BAR(2)(3)
Valve Body Size, Inches
TEMPER-
1/2, 3/4, & 1 1-1/2
ATURE,
C
C(4)(5) Port Diameter, mm
4.8 4.8
9.5 12.7 19.1 25.4 9.5 12.7 19.1 25.4 38.1
& 6.4 & 6.4
N04400 (Monel)/Composition Spiral Wound Gasket (Gasket Set 4)
–253 to 38 67.6 68.3 69.0 72.4 76.5 58.6 59.0 59.3 61.3 63.4 72.4
93 56.5 57.2 57.9 60.0 64.1 49.0 49.3 49.6 51.0 53.1 60.0
149 47.6 48.3 49.0 51.0 53.8 41.4 41.8 42.1 43.4 44.8 51.0
204 43.4 43.8 44.1 46.2 49.0 37.9 37.9 37.9 39.3 40.7 46.2
232 42.1 42.6 43.1 44.8 47.6 36.5 36.7 36.9 38.3 39.6 44.8
N06600 (Inconel)/Graphite Spiral Wound Gasket (Gasket Set 2) or N04400 (Monel)/PTFE Spiral Wound Gasket (Gasket Set 3)(5)
–253 to 38 94.5 96.2 97.9 104.1 114 77.9 79.0 80.0 82.7 87.6 105
93 89.6 91.4 93.1 98.6 108 73.8 74.5 75.2 78.6 82.7 99.3
149 85.5 87.2 88.9 94.5 103 70.3 71.4 72.4 75.2 79.3 94.5
204 81.4 83.1 84.8 89.6 98.6 66.9 68.0 69.0 71.0 75.2 90.3
260 78.6 80.4 82.1 86.9 95.2 64.8 65.5 66.2 69.0 73.1 87.6
316 76.5 77.9 79.3 84.1 92.4 62.7 63.4 64.1 66.9 71.0 84.8
371 73.8 75.2 76.5 81.4 88.9 60.7 61.4 62.1 64.8 68.3 81.4
427 71.0 72.4 73.8 78.6 86.2 58.6 59.3 60.0 62.1 66.2 78.6
PSI(2)(3)
TEMPER-
Port Diameter, Inches
ATURE,
F(4)(5) 3/16 3/16
3/8 1/2 3/4 1 3/8 1/2 3/4 1 1-1/2
& 1/4 & 1/4
N04400 (Monel)/Composition Spiral Wound Gasket (Gasket Set 4)
–425 to 100 980 990 1000 1050 1110 850 855 860 890 920 1050
200 820 830 840 870 930 710 715 720 740 770 870
300 690 700 710 740 780 600 605 610 630 650 740
400 630 635 640 670 710 550 550 550 570 590 670
450 610 618 625 650 690 530 535 535 555 575 650
N06600 (Inconel)/Graphite Spiral Wound Gasket (Gasket Set 2) or N04400 (Monel)/PTFE Spiral Wound Gasket (Gasket Set 3)(5)
–425 to 100 1370 1395 1420 1510 1660 1130 1145 1160 1200 1270 1520
200 1300 1325 1350 1430 1570 1070 1080 1090 1140 1200 1440
300 1240 1265 1290 1370 1500 1020 1035 1050 1090 1150 1370
400 1180 1205 1230 1300 1430 970 985 1000 1030 1090 1310
500 1140 1165 1190 1260 1380 940 950 960 1000 1060 1270
600 1110 1130 1150 1220 1340 910 920 930 970 1030 1230
700 1070 1090 1110 1180 1290 880 890 900 940 990 1180
800 1030 1050 1070 1140 1250 850 860 870 900 960 1140
1. Design EZ should not be used in flow down service including on-off applications.
2. Pressure drop cannot exceed maximum inlet pressure as indicated in the specifications on page 2.
3. The trim may be further limited by maximum pressure drops listed in tables 9 and 10.
4. Pressure drops at intermediate temperatures may be interpolated.
5. Maximum temperature capability of PTFE-coated N04400 (Monel) gaskets as used in gasket set 3 is 149C (300F).
14
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 13. Maximum Allowable Pressure Drops (Flow Up Only)(1) for Gasket Materials (2- through 4-Inch Valve Size)
BAR(2)(3)
Valve Body Size, Inches
TEMPER-
2 3 4
ATURE,
C
C(4)(5) Port Diameter, mm
4.8
9.5 12.7 19.1 25.4 50.8 50.8 76.2 50.8 101.6
& 6.4
N04400 (Monel)/Composition Spiral Wound Gasket (Gasket Set 4)
–253 to 38 52.4 52.8 53.1 54.5 55.8 70.3 55.2 70.3 49.0 73.8
93 43.4 43.8 44.1 45.5 46.9 58.6 46.2 58.6 40.7 61.4
149 37.2 37.2 37.2 37.9 39.3 49.6 38.6 49.6 34.5 51.7
204 33.8 33.8 33.8 34.5 35.9 44.8 35.2 45.5 31.0 46.9
232 32.8 32.8 32.8 33.4 34.8 43.4 34.1 44.1 30.3 45.5
N06600 (Inconel)/Graphite Spiral Wound Gasket (Gasket Set 2) or N04400 (Monel)/PTFE Spiral Wound Gasket (Gasket Set 3)(5)
–253 to 38 67.6 68.2 68.7 70.3 73.1 101 69.6 97.2 65.5 114
93 63.4 64.1 64.8 66.9 69.6 95.8 66.2 92.4 62.1 108
149 60.7 61.4 62.1 63.4 66.2 91.7 62.7 88.3 58.6 103
204 57.9 58.3 58.6 60.7 62.7 86.9 60.0 83.4 55.8 97.9
260 55.8 56.5 57.2 58.6 61.4 84.1 57.9 81.4 54.5 94.5
316 54.5 54.9 55.2 56.5 59.3 81.4 56.5 78.6 52.4 91.7
371 52.4 52.8 53.1 55.2 57.2 78.6 54.5 75.8 51.0 88.3
427 50.3 51.0 51.7 53.1 55.2 75.8 52.4 73.1 49.0 85.5
PSI(2)(3)
TEMPER-
Port Diameter, Inches
ATURE,
F(4)(5) 3/16
3/8 1/2 3/4 1 2 2 3 2 4
& 1/4
N04400 (Monel)/Composition Spiral Wound Gasket (Gasket Set 4)
–425 to 100 760 765 770 790 810 1020 800 1020 710 1070
200 630 635 640 660 680 850 670 850 590 890
300 540 540 540 550 570 720 560 720 500 750
400 490 490 490 500 520 650 510 660 450 680
450 475 475 475 485 505 630 495 640 440 660
N06600 (Inconel)/Graphite Spiral Wound Gasket (Gasket Set 2) or N04400 (Monel)/PTFE Spiral Wound Gasket (Gasket Set 3)(5)
–425 to 100 980 985 990 1020 1060 1470 1010 1410 950 1650
200 920 930 940 970 1010 1390 960 1340 900 1560
300 880 890 900 920 960 1330 910 1280 850 1490
400 840 845 850 880 910 1260 870 1210 810 1420
500 810 820 830 850 890 1220 840 1180 790 1370
600 790 795 800 820 860 1180 820 1140 760 1330
700 760 765 770 800 830 1140 790 1100 740 1280
800 730 740 750 770 800 1100 760 1060 710 1240
1. Design EZ should not be used in flow down service including on-off applications.
2. Pressure drop cannot exceed maximum inlet pressure as indicated in the specifications on page 2.
3. The trim may be further limited by maximum pressure drops listed in tables 9 and 10.
4. Pressure drops at intermediate temperatures may be interpolated.
5. Maximum temperature capability of PTFE-coated N04400 (Monel) gaskets as used in gasket set 3 is 149C (300F).
15
Product Bulletin
51.1:EZ
EZ Valve August 2002
Table 14. Maximum Flow Coefficient for Full-Sized Trim with Equal Percentage
Characteristic and Normal Flow Direction(1)
Valve Body Size, Inches Cv at Max Valve Plug Travel
1/2 4.47
3/4 9.00
1 13.2
1-1/2 28.1
2 53.8
3 114
4 190
1. Flow coefficients for linear and quick-opening valve plugs normally are somewhat greater.
Table 15. Port Diameters, Valve Plug Travel, and Stem and Yoke Boss Diameters
VALVE STEM AND YOKE BOSS
PORT DIAMETER, mm
MAX VALVE DIAMETERS, mm
VALVE BODY
PLUG TRAVEL, Standard Optional
SIZE, INCHES Equal Quick
Linear mm Yoke Yoke
Percentage(1) Opening Stem Stem
Boss Boss
1/2 or 3/4 4.8(2), 6.4(3), 9.5, 12.7, 19.1, 25.4 25.4 ---
1 4.8(2), 6.4(3), 9.5, 12.7, 19.1, 25.4 25.4 25.4 19 9.5 54 12.7 71
1-1/2 4.8(2), 6.4(3), 9.5, 12.7, 19.1, 25.4, 38.1 38.1 38.1
2 4.8(2), 6.4(3), 9.5, 12.7, 19.1, 25.4, 50.8 50.8 50.8 29
3 50.8, 76.2 76.2 76.2 38 12.7 71 19.1 90
4 50.8, 101.6 101.6 101.6 51
Inches
1/2 or 3/4 3/16(2), 1/4(3), 3/8, 1/2, 3/4, 1 1 ---
1 3/16(2), 1/4(3), 3/8, 1/2, 3/4, 1 1 1 3/4 3/8 2-1/8 1/2 2-13/16
1-1/2 3/16(2), 1/4(3), 3/8, 1/2, 3/4, 1, 1-1/2 1-1/2 1-1/2
2 3/16(2), 1/4(3), 3/8, 1/2, 3/4, 1, 2 2 2 1-1/8
3 2, 3 3 3 1-1/2 1/2 2-13/16 3/4 3-9/16
4 2, 4 4 4 2
1. 6.4 through 19.1 mm (1/4 through 3/4-inch) port diameters use Micro-Form valve plug.
2. Micro-Flow valve plug.
3. Also available in 1-flute and 3-flute Micro-Flute valve plugs.
Table 16. Typical Combinations of Metal Trim Parts for Equal Percentage (Including Micro-Form), Linear, and Quick Opening Valve
Plugs for Compliance with NACE MR0175 (Sour Service) Specifications
Valve Stem, Packing
Follower, Lantern Ring,
Trim Seat Ring
Valve Plug Bushing Seat Ring Packing Box Ring,
Designation Retainer
Pins, and
Disk Retainer
S31600 CF8M
85 Alloy 6B S31600
(316 stainless steel) (316 stainless steel)
85C(1) S31600/PTFE CF8M Alloy 6B S31600 S20910
S31600 (Valve Stem)
86 CF8M Alloy 6B S31600/CoCr-A
w/CoCr-A (alloy 6) seat S31600
S31600 (All Other
87 CF8M Alloy 6B S31600/CoCr-A Parts)
w/CoCr-A seat & guide
S31600/PTFE
87C(1) CF8M Alloy 6B S31600
w/CoCr-A guide
1. 85C and 87C are trims for PTFE-seat construction.
16
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 17. Bolting Materials and Temperature Limits for Bolting Compliance with NACE Specification MR0175
VALVE BODY TEMPERATURE
MATERIAL CAPABILITIES
BOLTING MATERIAL
C F
Min Max Min Max
NACE MR0175 (non-exposed bolting) (Standard)
WCC and Studs Steel SA-193-B7
–48(1) 427 –55(1) 800
CF8M (316 SST) Nuts Steel SA-194-2H
NACE MR0175 (exposed bolting) (Optional)
No Derating of Valve Required
WCC and Studs Steel SA-564-630 (H1150 dbl(2))
–46(1) 343 –50(1) 650
CF8M Nuts Steel SA-194-2HM
NACE MR0175 (exposed bolting) (Optional)
Requires Derating of Valve(3) When These Body-to-Bonnet Bolting Materials are Used
WCC and Studs Steel SA-193-B7M
–48(1) 427 –55(1) 800
CF8M Nuts Steel SA-194-2HM
1. –29C (–20F) with WCC valve body material.
2. Special heat treating required.
3. Derating is not required for Class 300 valves. Derating is required for valves rated at Class 600 and above. Contact your Fisher sales office for assistance in determining the derating
of valves when these body-to-bonnet bolting materials are used.
NACE Standard MR0175 Compliance The requirements of MR0175 are very specific and
the application of the standard to control valve
Standard procurement procedures and materials is quite complex. There are, however,
manufacturing processes used by Fisher assure that some general guidelines that are always followed:
control valves with sour service trim options will
comply with the requirements of NACE standard All carbon steel valve bodies and bonnets are
MR0175. Incoming raw materials are selected for heat-treated to 22 HRC maximum and are post-weld
sour service trims by specifications covering heat-treated.
chemical composition, forming, hardness, heat
treatment, and finish. In addition, the subsequent
machining, welding, and heat treatment of the Martensitic and cast precipitation hardening
materials being processed into finished parts is stainless steel are not used.
strictly regulated by manufacturing standards.
Control valve packings are jam style only.
Due to strict start-to-finish manufacturing quality
management, Fisher offers a high degree of Valve stems are made from S20910
confidence that the parts and assemblies provided (Nitronic 50).
for sour service will comply with MR0175. It is
unnecessary to request additional testing and
documentation to assure compliance with Primary trim materials are S31600 and alloy 6.
MR0175, in most cases. However, in cases where
documentation is required, the following items can No machining operations that cause
be provided: work-hardening of the materials are performed in the
manufacturing process.
Hardness test data
Plating and coatings are used only over
suitable base metals and are not intended for
Certificate of compliance to specification corrosion protection.
17
Product Bulletin
51.1:EZ
EZ Valve August 2002
Ordering Information
Inlet pressure and temperature must always be
limited by the applicable ANSI pressure/temperature
rating. Pressure drop information for various trim
material combinations is provided in tables 10 and
11. Pressure drop information for gasket materials is
listed in tables 12 and 13. The maximum allowable
pressure drop for the application must not exceed
the lowest value indicated for the combination of
materials selected.
12B7185–A Note
A6115/IL
NOTES:
Fisher does not assume responsibility
1 FOR A AND G DIMENSIONS, SEE FIGURE 8 for the selection, use, or maintenance
2 B=A/2 of any product. Responsibility for
proper selection, use, and
maintenance of any Fisher product
Figure 7. ENVIRO–SEAL Bellows Seal Bonnet Dimensions remains solely with the purchaser and
(also see table 18) end-user.
18
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Table 19. Standard Dimensions
D
Plain
Extension Bonnet
Bonnet
VALVE SIZE, INCHES
Style 1 Style 2
Stem Diameter, mm
9.5 12.7 19.0 9.5 12.7 19.0 9.5 12.7 19.0
1/2 or 3/4 127 149 --- 213 251 --- 303 319 ---
1 127 149 --- 213 251 --- 303 319 ---
1-1/2 124 146 --- 210 248 --- 300 316 ---
2 --- 165 162 --- 267 272 --- 465 ---
3 --- 191 187 --- 292 297 --- 495 487
4 --- 221 217 --- 322 327 --- 526 518
Stem Diameter, Inches
3/8 1/2 3/4 3/8 1/2 3/4 3/8 1/2 3/4
1/2 or 3/4 5.00 5.88 --- 8.38 9.88 --- 11.94 12.56 ---
1 5.00 5.88 --- 8.38 9.88 --- 11.94 12.56 ---
1-1/2 4.88 5.75 --- 8.25 9.75 --- 11.81 12.44 ---
2 --- 6.50 6.38 --- 10.50 10.69 --- 18.31 ---
3 --- 7.50 7.38 --- 11.50 11.69 --- 19.50 19.19
4 --- 8.69 8.56 --- 12.69 12.88 --- 20.69 21.38
19
Product Bulletin
51.1:EZ
EZ Valve August 2002
MATCH LINE
FOR
ACTUATOR
NOTES:
1 A
B+
AR4967–A
2 DESIGN EZ BODY
A0925–2 / IL
20
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Coefficients
Table 21. Design EZ, Quick Opening Valve Plug
Quick Opening
Quick Opening Characteristic
Port Maximum Coeffs. for
Valve Flow Valve Opening—Percent of Total Travel
Diameter Travel(1) 6 mm
FL(3)
Size, Coeffi-
(1/4 Inch)
Inches mm Inches mm Inches cient 10 20 30 40 50 60 70 80 90 100
Travel(2)
Cv --- 1.76 3.29 4.29 4.44 4.44 4.44 4.44 4.44 4.44 4.44 0.83
1/2 25.4 1 19 3/4 Kv --- 1.52 2.85 3.71 3.84 3.84 3.84 3.84 3.84 3.84 3.84 ---
XT --- 0.364 0.649 0.764 0.863 0.894 0.894 0.894 0.894 0.894 0.894 ---
Cv --- 3.85 7.19 9.40 9.72 9.72 9.72 9.72 9.72 9.72 9.72 0.88
3/4 25.4 1 19 3/4 Kv --- 3.33 6.22 8.13 8.41 8.41 8.41 8.41 8.41 8.41 8.41 ---
XT --- 0.314 0.559 0.654 0.742 0.769 0.769 0.769 0.769 0.769 0.769 ---
Cv 14.7 4.39 10.3 14.0 15.5 16.2 16.6 16.8 16.8 16.9 16.9 0.94
Kv 12.7 3.80 8.91 12.1 13.4 14.0 14.4 14.5 14.5 14.6 14.6 ---
1 25.4 1 19 3/4
XT 14.7 0.400 0.449 0.523 0.539 0.535 0.512 0.500 0.500 0.494 0.494 ---
Fd --- 0.20 0.29 0.39 0.48 0.50 0.50 0.50 0.50 0.50 0.50 ---
Cv 22.6 5.64 11.9 20.6 27.4 30.5 32.4 33.4 33.7 34.1 34.2 0.96
Kv 19.5 4.88 10.3 17.8 23.7 26.4 28.0 28.9 29.2 29.5 29.6 ---
38.1 1-1/2 19 3/4
XT 22.6 0.623 0.734 0.726 0.814 0.843 0.857 0.861 0.860 0.853 0.848 ---
1-1/2 Fd --- 0.16 0.24 0.32 0.39 0.45 0.50 0.50 0.50 0.50 0.50 ---
Cv 15.7 4.17 8.94 14.6 17.4 18.3 18.8 18.9 19.0 19.1 19.4 0.90
25.4 1
(4) (4) 19 3/4 Kv 13.6 3.61 7.73 12.6 15.1 15.8 16.3 16.3 16.4 16.5 16.8 ---
XT 15.7 0.617 0.791 0.793 0.904 0.925 0.924 0.922 0.915 0.905 0.878 ---
Cv 34.0 13.0 30.1 44.3 52.4 56.4 57.8 58.4 58.5 58.6 58.6 0.94
Kv 29.4 11.2 26.0 38.3 45.3 48.8 50.0 50.5 50.6 50.7 50.7 ---
50.8 2 29 1-1/8
XT 34.0 0.548 0.663 0.765 0.813 0.818 0.833 0.831 0.836 0.834 0.834 ---
2 Fd --- 0.17 0.28 0.36 0.43 0.49 0.50 0.50 0.50 0.50 0.50 ---
Cv 15.8 4.35 9.79 14.9 16.6 17.3 17.5 17.5 17.6 17.7 17.9 0.86
25.4 1
(4) (4) 19 3/4 Kv 13.7 3.76 8.47 12.9 14.4 15.0 15.1 15.1 15.2 15.3 15.5 ---
XT 15.8 0.524 0.594 0.695 0.877 0.937 0.944 0.958 0.952 0.942 0.921 ---
Cv 53.8 30.8 65.1 92.4 110 118 123 126 128 129 129 0.91
Kv 46.5 26.6 56.3 79.9 95.2 102 106 109 111 112 112 ---
76.2 3 38 1-1/2
XT 53.8 0.672 0.714 0.713 0.742 0.784 0.785 0.783 0.776 0.774 0.774 ---
3 Fd --- 0.17 0.27 0.35 0.42 0.47 0.50 0.50 0.50 0.50 0.50 ---
Cv 32.2 9.99 27.6 44.9 61.0 71.9 78.4 83.1 86.2 87.5 88.4 0.95
50.8 2
(4) (4) 29 1-1/8 Kv 27.9 8.64 23.9 38.8 52.8 62.2 67.8 71.9 74.6 75.7 76.5 ---
XT 32.2 0.527 0.511 0.652 0.720 0.780 0.820 0.814 0.798 0.790 0.779 ---
Cv 68.2 50.8 116 159 185 201 212 219 222 223 223 0.88
Kv 59.0 43.9 100 138 160 174 183 189 192 193 193 ---
101.6 4 51 2
XT 68.2 0.733 0.653 0.724 0.805 0.809 0.816 0.809 0.812 0.831 0.835 ---
4 Fd --- 0.18 0.28 0.36 0.42 0.48 0.50 0.50 0.50 0.50 0.50 ---
Cv 37.4 13.5 32.3 52.2 66.2 74.4 81.1 85.0 85.8 86.3 86.7 0.85
50.8 2
(4) (4) 29 1-1/8 Kv 32.4 11.7 27.9 45.2 57.3 64.4 70.2 73.5 74.2 74.6 75.0 ---
XT 37.4 0.490 0.556 0.609 0.672 0.793 0.772 0.728 0.714 0.711 0.704 ---
1. When using Type 655-EZ as a control valve for on-off service, the maximum travel for sizing purposes is 3/4-inch (19 mm).
2. When sizing self-operated regulators, use coefficients listed for 6 mm (1/4-inch) travel.
3. At 100% travel.
4. Restricted trim.
The flow coefficients shown on this page are appropriate for Design EZ-C valves.
21
Product Bulletin
51.1:EZ
EZ Valve August 2002
Notes: The coefficients shown on this page are also appropriate for Design EZ-C valves.
22
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Notes: The coefficients shown on this page are appropriate for Design EZ-C valves.
23
Product Bulletin
51.1:EZ
EZ Valve August 2002
Notes: The coefficients on this page are also appropriate for Design EZ-C valves.
24
Product Bulletin
51.1:EZ
August 2002 EZ Valve
25
Product Bulletin
51.1:EZ
EZ Valve August 2002
Specifications
Valve Sizes limited as shown in tables 8, 9, and 11. For soft
seats on NACE service, see figure 6.
1/2, 3/4, 1, 1-1/2, 2, 3, and
4-inch Shutoff Classification Per ANSI/FCI 70-2
and IEC 60534-4
Metal Seating: Class IV is standard. Class V is
optional.
End Connection Styles(1, 2) PTFE Composition Seating: Class VI
26
Product Bulletin
51.1:EZ
August 2002 EZ Valve
Specifications (continued)
Packing Arrangements 1 inch valve: 11 kg (25 lb)
Standard Material: Single PTFE V-ring 1-1/2 inch valve: 18 kg (40 lb)
Optional Materials: See table 6. 2 inch valve: 36 kg (80 lb)
ENVIRO-SEAL Packing Systems: See figure 4. 3 inch valve: 54 kg (120 lb)
ENVIRO-SEAL Packing Systems in vacuum 4 inch valve: 75 kg (165 lb)
service: Standard ENVIRO-SEAL packing
systems can be used in vacuum service with Valve Dimensions
packing rings in standard orientation. Do not
reverse the ENVIRO-SEAL PTFE packing rings. See figure 8. ENVIRO-SEAL bellows seal
Also, see Bulletin 59.1:061, ENVIRO-SEAL bonnet dimensions, figure 7
Packing Systems for Sliding-Stem Valves, for
more information.
Additional Options
Approximate Weights Lubricator or lubricator/isolating valve for
1/2 inch, 3/4 inch valves: 9 kg (20 lb) packing lubrication and valve body drain plug
1. DIN (or other) ratings and end connections can usually be supplied; consult your Fisher sales office.
2. Do not exceed the pressure/temperature limits in this bulletin. Any applicable standard or code limitations should not be exceeded.
3. For temperatures above 427C (800F), the Class 600 CF8M (316 stainless steel) valve body must be derated; contact your Fisher sales office for further information. Flanged valves derated
at 38C (100F) do not comply with ASME B16.34.
27
Product Bulletin
51.1:EZ
EZ Valve August 2002
Fisher is a mark owned by Fisher Controls International, Inc., a business of Emerson Process Management. The Emerson logo is a
trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use
or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Fisher does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and
maintenance of any Fisher product remains solely with the purchaser and end-user.
Fisher
28 Controls International, Inc. 2002; All Rights Reserved Printed in USA