Professional Documents
Culture Documents
BS 410 PDF
BS 410 PDF
BS 410 PDF
BSI
UDC 621.928.2:620.168.32
Specification for
BRITISH STANDARD
Test sieves
Incorporating
Amendment No. 1
BS 410:1986
BS 410:1986
British Standard
BCIRA
British Aggregate Construction Materials Industries
British Ceramic Society
British Laboratory Ware Association
Cement and Concrete Association
Cement Makers’ Federation
Coated Abrasives Manufacturers Association
Department of Trade and Industry (Warren Spring Laboratory)
Department of Transport (Highways)
Guild of Metal Perforators
Incorporated National Association of British and Irish Millers
Institution of Chemical Engineers
Institution of Mining and Metallurgy
Mechanical Handling Engineers Association
Ministry of Defence
National Coal Board
Society of Chemical Industry
Society of Cosmetic Scientists
Woven Wire Association
The following bodies were also represented in the drafting of the standard,
through subcommittees and panels:
© BSI 01-1999
Contents
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Page
Committees responsible Inside front cover
Foreword ii
1 Scope 1
2 Definitions 1
3 Sieve designation, construction and marking 2
4 Woven wire cloth in test sieves 2
5 Perforated plates in test sieves 5
Appendix A Information to be supplied with an enquiry and order 7
Appendix B Sieving areas and aperture tolerances expressed
as percentages 10
Appendix C Inspection of woven wire cloth 12
Appendix D Inspection of perforated plate 13
Appendix E Mesh number 14
Appendix F Calibration tests 15
Appendix G Maintenance of test sieves 16
Appendix H Used sieves 16
Figure 1 — Weaves of wire cloth 2
Figure 2 — Lid and receiver for round test sieves 3
Figure 3 — Specimen label 4
Figure 4 — Measurement of woven wire aperture size 4
Figure 5 — Arrangement of square holes 6
Figure 6 — Arrangement of round holes 6
Figure 7 — Tolerance band gauge for optically magnified sieve cloth 12
Figure 8 — Record card for inspection of woven wire cloth test sieve 13
Figure 9 — Record card for inspection of perforated plate test sieve 14
Figure 10 — Fields of measurement in 200 mm round test sieve 15
Table 1 — Dimensions of round test sieve frames 3
Table 2 — Wire cloth in test sieves: wire diameter and tolerances
on apertures 5
Table 3 — Perforated plate in test sieves: plate thickness, pitch
of holes, minimum bridge width and tolerance on individual apertures 8
Table 4 — Sieving areas and aperture tolerances expressed
as percentages 10
Table 5 — Mesh number 14
Table 6 — Number of apertures to be measured in a 200 mm
diameter test sieve 15
Publications referred to Inside back cover
© BSI 01-1999 i
BS 410:1986
Foreword
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
This British Standard, having been prepared under the direction of the General
Mechanical Engineering Standards Committee, supersedes BS 410:1976 which is
withdrawn.
For wire cloth test sieves the R 40/3 series of aperture sizes, where successive
sizes have a ratio of about 1.2, are specified. For perforated plate test sieves both
the R 40/3 and the R 20 series are specified particularly to meet the requirements
of the aggregate, coal and iron industries. A few special non-ISO1) aperture size
perforated plate test sieves, some of such long standing that they have to be
retained and others of larger size than is required by ISO/TC 24, are also included
[see Table 3 c)].
Mesh numbers are included in Appendix E.
A specification for electroformed test sieves is being developed by ISO/TC 24 and
the “nominal size of openings” is specified in ISO 565-1983. A British Standard
specification for electroformed sheet test sieves is in preparation.
The methods of use of test sieves are described in BS 1796.
In Figure 3 and Figure 7 the term “micron” is used as this is widely accepted in
industry as representing micrometre (µm).
This revised standard now includes an additional aperture size, 32 µm, and
requirements for nesting round test sieves.
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 16, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on
the inside front cover.
1)
International Organization for Standardization.
ii © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
1 Scope 2.9
wire diameter
This British Standard specifies requirements for
sieves used for testing the size distribution of the diameter of the wire in the woven cloth
granular products in the particle size range 2.10
from 125 mm down to 32 µm. warp
Appendix G gives information on the maintenance all wires running lengthwise of the cloth as woven
of test sieves.
2.11
NOTE The titles of the publications referred to in this standard
are listed on the inside back cover.
weft (shoot)
all wires running crosswise of the cloth as woven
2 Definitions 2.12
For the purposes of this British Standard the type of weave
following definitions apply2). the way in which warp and weft wires cross each
2.1 other
test sieve 2.13
a sieve, intended for the particle size analysis of the plain weave
material to be sieved, which conforms to a test sieve the weave in which every warp wire crosses
standard specification alternately above and below every weft wire and
2.2 vice versa [see Figure 1 a)]
nest of test sieves 2.14
a set (regular or irregular) of test sieves assembled twilled weave
together with a lid (cover) and receiver (pan) The weave in which every warp wire crosses
2.3 alternately above and below every second weft wire
sieving medium and vice versa [see Figure 1 b)]
a surface containing regularly arranged apertures 2.15
of uniform shape and size perforated plate
2.4 a sieving medium consisting of a plate with uniform
frame holes in symmetrical arrangement
a rigid framework which supports the sieving 2.16
medium and limits the spread of the material being pitch (centres)
sieved the distance between corresponding points of two
2.5 adjacent holes in a perforated plate
lid (cover) 2.17
a cover which fits snugly over a sieve to prevent bridge width (bar)
escape of the material being sieved the distance between the nearest edges of two
2.6 adjacent holes in a perforated plate
receiver (pan) 2.18
a pan which fits snugly beneath a sieve to receive margin
the whole of the passing fraction the distance between the outside edges of the
2.7 outside rows of holes and the edges of a perforated
aperture size plate
the dimension defining an opening 2.19
2.8 plate thickness
woven wire cloth the thickness of the plate after perforation
a sieving medium of wires which cross each other to
form the apertures
2)
Taken from ISO 2395.
© BSI 01-1999 1
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
3)
Marking BS 410:1986 on or in relation to a product is a claim by the manufacturer that the product has been manufactured in
accordance with the requirements of the standard. The accuracy of such a claim is therefore solely the manufacturer’s
responsibility. Enquiries as to the availability of third party certification should be addressed to the appropriate certification
body.
2 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
mm mm mm mm mm mm mm
© BSI 01-1999 3
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
4 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Table 2 — Wire cloth in test sieves: wire 5 Perforated plates in test sieves
diameter and tolerances on apertures
5.1 Arrangement of square holes
Apertures in the range 16 mm to 20 µm
Nominal Nominal Tolerances Square holes shall be arranged in line with the
aperture wire centre points at the vertices of squares, as shown in
size diameter Maximum Tolerance Intermediate
in test tolerance for tolerance Figure 5.
sieve for size of average
an aperture 5.2 Arrangement of round holes
individual
aperture Round holes shall be arranged with the centres at
X Y Z the apices of equilateral triangles, as shown in
mm mm mm mm mm Figure 6.
16.0 3.15 + 0.99 ± 0.49 + 0.74 NOTE Plated mild steel is commonly supplied except at the
13.2 2.80 + 0.86 ± 0.41 + 0.64 lower end of the aperture range where brass may be found to be
11.2 2.50 + 0.77 ± 0.35 + 0.56 more suitable. The purchaser should state in the enquiry specific
requirements, if any, for the material of the perforated plate.
9.50 2.24 + 0.68 ± 0.30 + 0.49 5.3 Plate thickness
8.00 2.00 + 0.60 ± 0.25 + 0.43
6.70 1.80 + 0.53 ± 0.21 + 0.37 Perforated plates shall be of uniform thickness and
shall lie in the range given in Table 3.
5.60 1.60 + 0.47 ± 0.18 + 0.32
NOTE The nominal plate thicknesses stated in Table 3 are
4.75 1.60 + 0.42 ± 0.15 + 0.28
preferred.
4.00 1.40 + 0.37 ± 0.13 + 0.25
5.4 Pitch
3.35 1.25 + 0.32 ± 0.11 + 0.22
2.80 1.12 + 0.29 ± 0.09 + 0.19 The pitch shall be:
2.36 1.00 + 0.25 ± 0.08 + 0.17 a) the nominal pitch stated in Table 3; or
2.00 0.90 + 0.23 ± 0.07 + 0.15 b) up to 15 % larger than the nominal pitch stated
1.70 0.80 + 0.20 ± 0.06 + 0.13 in Table 3; or
1.40 0.71 + 0.18 ± 0.05 + 0.11 c) smaller than the nominal pitch stated in
1.18 0.63 + 0.16 ± 0.04 + 0.10 Table 3 provided that individual bridge widths
1.00 0.56 + 0.14 ± 0.03 + 0.09 comply with 5.5.
µm µm µm µm µm 5.5 Bridge width
850 500 + 127 ± 29 + 78 No individual bridge shall be less than half of the
710 450 + 112 ± 25 + 69 width given by subtracting the nominal aperture
600 400 + 101 ± 21 + 61 size from the nominal pitch.
500 315 + 90 ± 18 + 54 NOTE Minimum bridge widths are given in Table 3.
425 280 + 81 ± 15 + 48
5.6 Workmanship
355 224 + 72 ± 13 + 43
Perforated plates shall be uniformly and cleanly
300 200 + 65 ± 12 + 38 punched. The radius at the corners of square holes
250 160 + 58 ± 9.9 + 34 shall not exceed 0.05W + 0.30 mm, where W is the
212 140 + 52 ± 8.7 + 30 aperture size expressed in millimetres.
180 125 + 47 ± 7.6 + 27 5.7 Mounting
150 100 + 43 ± 6.6 + 25
The perforated plate shall be mounted with the
125 90 + 38 ± 5.8 + 22
punch entry side uppermost, i.e. burr down.
106 71 + 35 ± 5.2 + 20 The crevices above and below the plate at its
90 63 + 32 ± 4.6 + 18 junction with its frame shall be filled and left
75 50 + 29 ± 4.1 + 17 smooth.
63 45 + 26 ± 3.7 + 15 5.8 Tolerances on aperture size
53 36 + 24 ± 3.4 + 14
45 32 + 22 ± 3.1 + 13 Each aperture size of an unused sieve shall comply
with the nominal size of the sieve within the limits
38 30 + 20 ± 2.9 + 12 of tolerance shown in Table 3.
25 25 + 16 ± 2.5 +9 NOTE Aperture size is measured on the centre lines of square
20 20 + 14 ± 2.3 +8 holes (see 5.1) and on the diameter of round holes (see 5.2).
NOTE The aperture sizes taken ISO 565. They are in an
R40/3 series based on 1 mm with a ratio between successive sizes
of about 1:2. The siazes in bold type are the principal sizes stated
in ISO 565 and are preferred.
© BSI 01-1999 5
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
5.9 Inspection
5.9.1 General. The manufacturer shall test each test
sieve before sale and shall supply a record card
(see Appendix D).
NOTE The purchaser should state in his order when a more
detailed test, i.e. a calibration test in accordance with
Appendix F, is required.
5.9.2 Survey for condition. When tested in
accordance with D.2, the perforated plate shall not
show any obvious faults, e.g. irregularly formed
holes, ragged edges and burrs upward.
5.9.3 Oversize apertures. When tested in accordance
with D.3 and D.4 no aperture shall exceed the
maximum dimension given in Table 3.
6 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Appendix A Information to be
supplied with an enquiry and order
The purchaser should state the following with an
enquiry and order:
a) the designation of the sieve (see 3.1);
b) the sieving medium (i.e. woven wire cloth,
square hole or round hole perforated plate);
c) frame size and shape, and any other necessary
details, e.g. nesting requirements (see 3.5) or
wire diameter (see 4.2);
d) any material requirements or restrictions for
frame, sieving medium and fillets; whether
statement of wire diameter is required (see 4.1
and 4.5);
e) whether a receiver is required (see 3.3);
f) whether a lid is required (see 3.3);
g) whether a more detailed test is required
(see 4.6.1 and 5.9.1).
© BSI 01-1999 7
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Table 3 — Perforated plate in test sieves: plate thickness, pitch of holes, minimum
bridge width and tolerance on individual apertures
a) Apertures in the range 125 mm to 4 mm; square hole and round hole
Nominal Plate thickness Nominal pitch of holes Minimum bridge Tolerance on
aperture size width individual apertures
R40/3 R/20 Nominala Max. Min.
series series
mm mm mm mm mm mm mm mm
125 125 160 17.5 ± 1.00
112 140 14.0 ± 0.95
106 132 13.0 ± 0.90
100 125 12.5 ± 0.85
90.0 90.0 112 11.0 ± 0.80
80.0 2.5 3.0 2.0 100 10.0 ± 0.70
75.0 95 10.0 ± 0.70
71.0 90 9.5 ± 0.65
63.0 63.0 80 8.5 ± 0.60
56.0 71 7.5 ± 0.55
53.0 67 7.0 ± 0.55
50.0 63 6.5 ± 0.55
45.0 45.0 56.0 5.5 ± 0.50
40.0 50.0 5.0 ± 0.45
37.5 47.5 5.0 ± 0.45
35.5 45.0 4.75 ±0.40
31.5 31.5 40.0 4.25 ± 0.40
28.0 35.5 3.75 ± 0.35
26.5 33.5 3.5 ± 0.35
25.0 2.0 2.5 1.5 31.5 3.25 ± 0.35
22.4 22.4 28.0 2.8 ± 0.30
20.0 25.0 2.5 ± 0.30
19.0 23.6 2.3 ± 0.29
18.0 22.4 2.2 ± 0.28
16.0 16.0 20.0 2.0 ± 0.27
14.0 18 2.0 ± 0.26
13.2 17 1.9 ± 0.25
12.5 16 1.75 ±0.24
11.2 11.2 1.5 2.0 1.0 14 1.4 ± 0.23
10.0 12.6 1.3 ± 0.21
9.50 12.1 1.3 ± 0.21
9.00 11.6 1.3 ± 0.20
8.00 8.00 10.4 1.2 ± 0.19
7.10 9.4 1.15 ± 0.18
6.70 8.9 1.1 ± 0.17
6.30 8.5 1.1 ± 0.17
5.60 5.60 1.5 2.0 1.0 7.7 1.05 ± 0.15
5.00 6.9 0.95 ± 0.14
4.75 6.6 0.93 ± 0.14
4.50 6.3 0.9 ± 0.14
4.00 4.00 5.8 0.9 ± 0.13
8 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Table 3 — Perforated plate in test sieves: plate thickness, pitch of holes, minimum bridge width
and tolerance on individual apertures
b) Round holes only in the range 3.55 mm to 1 mm
Nominal Plate thickness Nominal pitch of Minimum bridge Tolerance on individual
aperture size holes width apertures
R40/3 R/20 Nominala Max. Min.
series series
mm mm mm mm mm mm mm mm
3.55
5.2 0.83 ± 0.12
3.55 5.0 0.83 ± 0.11
3.15 4.7 0.78 ± 0.11
2.80 2.80 1.00 1.25 0.8 4.35 0.78 ± 0.11
2.50 3.9 0.7 ± 0.11
2.36 3.75 0.7 ± 0.11
2.24 3.6 0.67 ± 0.10
2.00 2.00 3.3 0.65 ± 0.09
1.80 3.1 0.65 ± 0.08
1.70 3.0 0.65 ± 0.08
1.60 2.75 0.58 ± 0.08
1.40 1.40 0.5 0.63 0.4
2.6 0.6 ± 0.08
1.25 2.45 0.6 ± 0.08
1.18 2.4 0.6 ± 0.07
1.12 2.22 0.55 ± 0.07
1.00 1.00 2.0 0.5 ± 0.07
c) Non-ISO sizes; round holes only
Nominal Plate thickness Nominal pitch of Minimum bridge Tolerance on individual
aperture size Nominal a Max. Min. holes width apertures
mm mm mm mm mm mm mm
200b ± 1.55
180b ± 1.40
160b ± 1.25
140b ± 1.10
120 150 15 ± 0.95
70 2.5 3.0 2.0 90 10 ± 0.65
60 75 7.5 ± 0.60
35 45 5 ± 0.40
30 2.0 2.5 1.5 37.5 3.75 ± 0.40
15 19 2.0 ± 0.27
7.5 1.5 2.0 1.0 10 1.25 ± 0.19
NOTE 1 Bold type signifies preferred sizes.
NOTE 2 The sizes listed under “Nominal aperture size” are the total specified by ISO 565 for perforated plate in test sieves.
However, manufacturers of perforated plate test sieves may equip themselves for making only those sizes for which there is a
demand sufficient to justify the expense of their tools. When particle sizes are being considered for products, enquiries should be
made as to the stock position of test sieves, having the aperture size in mind.
NOTE 3 The sizes listed under “Nominal aperture size” in the R40/3 series are based on 1 mm with a ratio between successive sizes
of about 1:2 those in the R20 series have a ratio of about 1:12. The sizes in bold type are the principal sizes stated in ISO 565 and
are preferred.
a
See note to 5.3
b
Test sieves of these aperture sizes may be made as single ring gauges. A minimum plate thickness of 3 mm is recommended.
© BSI 01-1999 9
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
90.0 65 59 ± 0.9
80.0 64 58 ± 0.9
75.0 62 57 ± 0.9
71.0 56 51 ± 0.9
63.0 62 56 ± 0.95
56.0 63 57 ±1
53.0 63 57 ±1
50.0 64 58 ±1
45.0 65 59 ±1
40.0 64 58 ±1
37.5 61 55 ±1
35.0 56 51 ±1
31.5 62 56 ± 1.5
38.0 62 56 ± 1.5
26.5 63 57 ± 1.5
25.0 63 57 ± 1.5
22.4 64 58 ± 1.5
20.0 64 58 ± 1.5
19.0 65 59 ± 1.5
18.0 65 59 ± 1.5
16.0 70 64 58 +7 ±3 +5 ± 1.5
14.0 60 54 ±2
13.2 68 60 55 +7 ±3 +5 ±2
12.5 61 55 ±2
11.2 67 64 58 +7 ±3 +5 ±2
10.0 61 55 ±2
9.5 65 61 55 +7 ±3 +5 ±2
9.00 60 54 ±2
8.00 64 57 52 +8 ±3 +6 ± 2.5
7.10 57 52 ± 2.5
6.70 62 52 47 + 8.5 ±3 +6 ± 2.5
6.30 55 50 ± 2.5
5.60 60 49 44 +9 ±3 +6 ± 2.5
5.00 52 47 ± 2.5
4.75 56 47 43 +9 ±3 +6 ±3
4.50 51 46 ±3
4.00 55 44 40 + 10 ±3 +7 ±3
3.55 42 ± 3.5
3.35 53 38 + 10 ±3 +7 ± 3.5
3.15 40 ± 3.5
10 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
2.00 48 32 + 12 ±3 +8 ± 4.5
1.80 30 ± 4.5
1.70 46 31 + 12 ±3 +8 ± 5.5
1.60 30 ±5
1.40 44 28 + 13 ±3 +8 ± 5.5
1.25 23 ± 6.5
1.18 43 27 + 14 ±3 +9 ±7
1.12 23 ±6
1.00 41 25 + 15 ±3 +9 ±7
120a 58 ± 0.8
70a 55 ± 0.9
60a 58 ±1
35a 55 ±1
30a 58 ± 1.5
15a 57 ±2
7.5a 51 ± 2.5
µm % % % %
850 40 +1 5 ± 3.5 +9
710 37 + 16 ±4 + 10
600 36 + 17 ±4 + 11
500 38 + 18 ±4 + 11
425 36 + 19 ±4 + 12
355 38 + 20 ±4 + 12
300 36 + 21 ±4 + 13
250 37 + 22 ±4 + 13
212 36 + 24 ± 4.5 + 14
180 35 + 24 ±5 + 15
150 36 + 26 ±5 + 16
125 34 + 29 ±5 + 17
106 36 + 31 ±5 + 18
90 35 + 33 ±5 + 19
75 36 + 36 ±5 + 21
63 34 + 39 ±5 + 22
53 35 + 43 ±5 + 24
45 34 + 43 ±6 + 27
38 31 + 53 ±6 + 29
32 28 + 59 ±8 + 34
a
Non-ISO sizes; round hole perforated plate only.
© BSI 01-1999 11
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
B.2 The formulae for calculating percentage sieving C.4 Variations of aperture size
areas are as follows: Check the proportion of apertures that exceed the
a) woven wire cloth intermediate limit, i.e. nominal aperture size + Z.
2 Take measurements across the two diameters of the
W
----------------------- × 100 sieve frame, parallel to the warp and weft directions
2
(W + d) and/or in areas of irregular apertures as found
b) square hole perforated plate from C.3.
NOTE The measurements may be carried out rapidly using a
2 limit gauge in the form of a scale (see Figure 7) or by individual
W
-------- × 100 gauges for coarser mesh sieves. At least 100 apertures should be
2
p observed, if possible, in each direction.
c) round hole perforated plate Record the number of apertures whose size in either
the warp or weft direction falls within the tolerance
2
π (W ⁄ 2) band of (nominal + Z) and (nominal + Y) and
-------------------------- × 100
2 express as a proportion of the total apertures
0.866p
checked.
or NOTE This method should be used to confirm that no apertures
2 exceed the maximum of (nominal + X ); it may also be used to
W make an assessment of the distribution of the aperture width in
-------- × 90.7
2 the various tolerance bands, namely:
p less than (nominal – Y )
where between (nominal – Y ) and (nominal + Y )
between (nominal + Y ) and (nominal + Z )
W is the nominal aperture size; between (nominal + Z ) and (nominal + X )
d is the wire diameter (see Table 2);
p is the pitch (see Table 3).
NOTE The maximum aperture size specified in this standard
for wire cloth is 16 mm; the minimum aperture size specified for
square hole perforated plate is 4 mm, and the minimum aperture
size specified for round hole perforated plate is 1 mm.
12 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Times used Tester Visual survey Average aperture size Apertures above intermediate
and maximum limits
Date aperture
Warp direction Weft direction Warp direction Weft direction
New ABC/86/10 Within ± Y Within ± Y Less than 6 % Less than 6 %
NOTE It is the user’s responsibility to ensure that a used sieve is re-examined. He, or a referee, should make retests
according to the circumstances, and with a frequency appropriate to the degree of use that the sieve has undergone. For
further information, see Appendix H of BS 410:1986.
Figure 8 — Record card for inspection of woven wire cloth test sieve
© BSI 01-1999 13
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Times used Tester Date Visual survey Compliance with the tolerances of BS 410
New ABC 86/11
NOTE It is the user’s responsibility to ensure that a used test sieve is re-examined. He, or a referee, should make retests
according to the circumstances, and with a frequency appropriate to the degree of use that the sieve has undergone. For
further information see Appendix H of BS 410:1986.
Figure 9 — Record card for inspection of perforated plate test sieve
14 1.18 85 180
16 1.00 100 150
120 125
150 106
170 90
200 75
240 63
300 53
350 45
400 38
440 32
14 © BSI 01-1999
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
µm
850 10 10 100
710 10 12 120
600 10 15 150
500 10 15 150
425 10 20 200
355 10 25 250
300 10 30 300
250 10 30 300
212
180
150
125
106
90 15 20 300
75
63
Figure 10 — Fields of measurement in
53
a 200 mm round test sieve
45
38
32
In the cases of 100 mm and 300 mm diameter sieve
frames, the number of fields for measurement
should be 4 and 15 respectively.
© BSI 01-1999 15
BS 410:1986
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
For aperture sizes larger than 3.35 mm, it is usual G.2 Occasionally sieves may be washed in warm
to check the size with engineers’ gauges, and 20 deionized water containing a liquid synthetic
and 30 apertures may be assessed rapidly by this detergent. After washing, the sieves should be
means. If a sieve has 20 apertures or less, then all rinsed thoroughly in deionized water and dried at a
apertures should be measured. temperature not exceeding 80 °C. It is important to
If, when making this test, the measured average note that test sieves should not be heated to high
aperture width is found to be so uniform in the first temperature. The sieves may be cleaned by
few fields that the full recommended number of immersing in a suitable liquid, e.g. alcohol or
fields is not measured, then the result of the fields deionized water in an ultrasonic bath and treated
tested should be shown on the record card. for 15 s to 20 s with a frequency not less than 30 kHz
and power input not exceeding 60 W/L.
F.3 Perforated plate test sieves
G.3 Wire mesh test sieves, particularly those with a
When more detailed information is required about
nominal aperture size smaller than 3.35 mm,
the apertures in the perforated plate in a test sieve,
should not be brushed or exposed to compressed air.
either more apertures should be checked by limit
gauging or the dimensions of apertures should be
Appendix H Used sieves
measured directly.
F.4 Checking with a reference sample H.1 User’s tests on used sieves
Sieves can be checked by sieving known material The sizes and tolerances in this standard apply to
and comparing the amount of residue on the sieve new sieves. With continued use, test sieves will
with that expected. Known material can be either: wear; it is therefore necessary for the apertures to
a) reference material with agreed particle size be remeasured from time to time.
distribution; or If the user is not prepared to make such periodic
b) a material that has also been sieved on a set of reinspections, recourse may be made to specialists
master test sieves reserved for this checking in testing.
operation. H.2 Wear allowances on test sieves
NOTE For information on the availability of powders with The tolerances on sieve apertures are determined by
certified particle size distribution, apply to one of the following
bodies.
the degree of closeness to nominal values attainable
1) Community Bureau of Reference in current manufacturing practice. Increases in
BCR aperture size (due to wear) which may be acceptable
Rue de la Loi 200 in service are determined by the requirements of the
B1049 Brussels product, and may well be included in the product
2) National Bureau of Standards specification. They are not necessarily the same as
Washington DC 20234
the manufacturing tolerance.
USA
3) Office of Reference Materials H.3 Applicability of marking
Laboratory of the Government Chemist The designation “TEST SIEVE TO BS 410” is not
Queens Road
applicable when the apertures of a test sieve no
Appendix G Maintenance of test sieves longer comply with the appropriate tolerances
according to the marking on the label on the sieve
G.1 Before each use the sieving medium and frame frame (see 3.6).
should be inspected and if necessary cleaned. The
cleaning of the sieve should be carried out with
great care so that the sieving medium is not
damaged. The sieving medium should not be
fingered.
16 © BSI 01-1999
BS 410:1986
Publications referred to
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
© BSI 01-1999
|
|
|
|
|
|
|
| BSI Ð British Standards Institution
Licensed Copy: Dong Su Lee, Hyundai Engineering Constructi, Fri Nov 02 05:21:57 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
|
|
|
|
|
|
|
| BSI is the independent national body responsible for preparing British Standards. It
|
| presents the UK view on standards in Europe and at the international level. It is
| incorporated by Royal Charter.
|
|
| Revisions
|
|
| British Standards are updated by amendment or revision. Users of British Standards
|
| should make sure that they possess the latest amendments or editions.
|
|
| It is the constant aim of BSI to improve the quality of our products and services. We
|
| would be grateful if anyone finding an inaccuracy or ambiguity while using this
| British Standard would inform the Secretary of the technical committee responsible,
|
| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.
|
| Fax: 020 8996 7400.
|
|
| BSI offers members an individual updating service called PLUS which ensures that
|
| subscribers automatically receive the latest editions of standards.
|
|
| Buying standards
|
| Orders for all BSI, international and foreign standards publications should be
|
| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
|
|
| In response to orders for international standards, it is BSI policy to supply the BSI
|
| implementation of those that have been published as British Standards, unless
|
| otherwise requested.
|
|
| Information on standards
|
| BSI provides a wide range of information on national, European and international
|
| standards through its Library and its Technical Help to Exporters Service. Various
|
| BSI electronic information services are also available which give details on all its
|
| products and services. Contact the Information Centre. Tel: 020 8996 7111.
|
| Fax: 020 8996 7048.
|
|
| Subscribing members of BSI are kept up to date with standards developments and
| receive substantial discounts on the purchase price of standards. For details of
|
| these and other benefits contact Membership Administration. Tel: 020 8996 7002.
|
| Fax: 020 8996 7001.
|
|
| Copyright
|
|
| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
|
| the publications of the international standardization bodies. Except as permitted
| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
|
| stored in a retrieval system or transmitted in any form or by any means ± electronic,
|
| photocopying, recording or otherwise ± without prior written permission from BSI.
|
|
| This does not preclude the free use, in the course of implementing the standard, of
|
| necessary details such as symbols, and size, type or grade designations. If these
|
| details are to be used for any other purpose than implementation then the prior
| written permission of BSI must be obtained.
|
|
| If permission is granted, the terms may include royalty payments or a licensing
|
| agreement. Details and advice can be obtained from the Copyright Manager.
|
| Tel: 020 8996 7070.
|
|
|
|
|
|
|
|
|
BSI |
|
389 Chiswick High Road |
|
London |
|
W4 4AL |
|
|
|
|
|
|