Professional Documents
Culture Documents
Mechanical 01-11-2020 PDF
Mechanical 01-11-2020 PDF
Mechanical 01-11-2020 PDF
Select One;
Ans: B
Q2. An automobile heats up while sitting in a parking lot in sunny day. The process can
be assumed to be.
a) Isothermal
b) Isobaric
c) Isometric
d) Adiabatic
Ans: B
Q3. For a balanced counter – flow heat exchanger. The temperature profiles of the two
fluids are.
a) Is usually laminar
b) Results in significant energy loss
c) Can be analysed using Bernoulli’s equation
d) Has a relatively small loss coefficient
Ans: B
Q5. A Bid manager, is in charge of a closed bid in which several firms are involved.
The last day of the bidding period arrives, and one firm has not yet submitted an entry.
Bob calls the firm and asks if they are going to submit a bid, and they have been too
busy to write proposal but might be able to get one worked out by the next day. He
should.
a) Open the bid and reveal the lowest bid to encourage the firm to enter
b) Open the bids and quote a false low bid so they will enter, but he will not be
giving away the contract.
c) Tell them he can’t do anything for them.
d) Allow the firm to enter a late bid
Ans: C
Q6. PE 522-A simply supported, uniformly loaded beam is found to deflect excessively
when subjected to a fixed total load. Assume the beam must be made of metal and of
a rectangular cross section. If the length cannot be changed, the deflection can be
reduced by at least 50% by:
Ans: A
Q7. PE 527-A spring is made from 0.1055-in diameter wire. If the spring has a free
length of 3 in. a spring constant of 20 lb/in. and 10 total coils (ground and squared
ends), the force (lb) required to fully compress the spring is most nearly:
a) 14
b) 32
c) 39
d) 71
Ans: C
Q8. PE 520-A one room building is being exhausted by a large fan. Louvers along one
wall allow makeup air from the outside. Given conditions are as follows:
Ans: C
Q9. PE 521-A space has its own thermostat, is served by a VAV system, and has a
design sensible heat gain of 19,800 Btu/hr. the supply air temperature from the air-
handling unit is 54°F db. The space thermostat is set at 78°F, and the VAV box has a
minimum flow setting of 210 cfm and a maximum of 750 cfm. The quantity of supply air
(cfm) provided by the VAV box when the space sensible load is 5,000 Btu/hr is most
nearly:
a) 190
b) 210
c) 560
d) 750
Ans: B
Q10. A 350-in^3 –displacement V8 engine delivers 200 hp while running at 4,200 rpm.
At these conditions the brake-specific fuel consumption and the engine friction power
is 50 hp. Fuel density is 42.8 lbm/ft^3. The fuel consumption (gpm) is:
a) 0.26
b) 0.38
c) 0.48
d) 3.00
Ans: C
Ans: A
a) Hardening
b) ----
c) ----
Ans: A
a) 88A
b) ----
c) ----
Ans: A
Q14. Dummy Activity on the diagram exist in order not to confuse with the previous
activities due to:
a) Burst activities
b) Merge activities
c) Parallel activities
d) Independent activities
Q15. The pressure loss due to friction in a horizontal section of constant diameter pipe
can be calculated using;
a) Darcy equation
b) Chezy-Manning equation
c) Bernoulli’s equation
d) Navier-Stokes equation
Ans: A
Q16. Strain hardening can lead with ductile metals for …… and …… to be plastically
Deformed:
a) Buckling
b) Fatigue
c) Creep
Ans: B
Q19. Equivalent diameter of rectangular tube with breadth and width 36 in and 24 in is:
Given ( De= 1.3 x (axb)^0.625 / (a+b)^0.25 )
a) 32 in
b) 20 in
c) 45 in
Ans: 32 in
Q20.The activity on the node network shown below describes a project consisting of 8
tasks A-H. Each node indicates activity duration in weeks. All the relationships are finsh
to start. The minimum time to complete the project is:
a) 15 weeks
b) 16 weeks
c) 17 weeks
d) 18 weeks
Ans: C
Q21.A centrifugal pump with 350gpm and 1750 rpm deliver water up to 115 ft, the dia
of impeller is 12.5 in it is calculated that the impeller can pump up to 140 ft. the
manufacture need to trim the impeller, how much need to trim the impeller:
Given ( n1xd1/h1^0.5 = n2xd2/h2^0.5)
a) 7.4
b) 8
c) 10
d) 11
Q22. A system used in an area with pressure difference fan used to control smoke from
this specific area the system is:
a) Smoke control
b) Extraction Fan
c) Ventilation
Q24. One problem with reservoir and pump in between pipe running, given kinematic
viscosity, nominal dia of pipe, equalent length of elbow, equalent length of pump
starting, then ask to find pressure drop between pump and reservoir.
Q25. One question from HVAC, given 5000 cfm at 32 lb(forgot the unit) and 2500 cfm
at 24 lb(forgot the unit) then this two mixed together asking the combined air
property.