Professional Documents
Culture Documents
Fiber Testing PDF
Fiber Testing PDF
SEPTEMBER 2019
SST 1/11
FIBER LINK TEST RESULTS
• TEST SET UP
• GAIN
• Input P1DB
• NF
• OIP3
• OIP2
• SFDR
SST 2/11
SETUP
Note: Input of the Fiber link is terminated by 50 ohm load for NF test.
Two signal generators and power combiner are used for OIP3 test.
SST 3/11
GAIN
GAIN
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
New units will be tested using Network Analyzers.
Input Power = -30 dBm
SST 4/11
Input P1dB
Note: Input P1dB = -9 dBm for 50MHz Note: Input P1dB = -8 dBm for 10GHz Note: Input P1dB = -10 dBm for 17GHz
Pin = -30dBm Pout = -23.6dBm Gain= 6.4dB Pin = -30dBm Pout = -27.1dBm Gain= 2.9dB Pin = -30dBm Pout = -25.5dBm Gain= 4.5dB
Pin = -9dBm Pout = -3.6dBm Gain= 5.4 dB Pin = -8dBm Pout = -6.1dBm Gain= 1.9 dB Pin = -10dBm Pout = -6.5dBm Gain= 3.5dB
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 5/11
NF @ 1GHz
NF @ 1GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 6/11
NF @ 10GHz
NF @ 10GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 7/11
NF @ 17GHz
NF @ 17GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 8/11
OIP3 @ 1GHz
OIP3 @1GHz
OIP3=5dBm @ 1GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 9/11
OIP3 @ 10GHz
OIP3 @10GHz
OIP3=3.5dBm @ 10GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 10/11
OIP3 @ 17GHz
OIP3 @17GHz
OIP3=1dBm @ 17GHz
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 11/11
OIP3 - NOTE
OIP3 of the signal analyzer is very high so it does not effect the results.
We have checked the results with the different input attenuation level (10,
20, 30dB) and observed same results.
SST 12/11
OIP2
-30 dBm -25 dBm -80 dBm -26 dBm -70 dBm -26 dBm -80 dBm
-25 dBm -20 dBm -70 dBm -21 dBm -60 dBm -21.8 dBm -71.8 dBm
-20 dBm -15dBm -59 dBm -16 dBm -50 dBm -16.8 dBm -62 dBm
-15 dBm -10 dBm -49 dBm -11.6 dBm -41 dBm -12 dBm -53 dBm
Note: Input cable (Minibend 12 inch) and output cable (Minibend 16 inch) are not calibrated.
SST 13/11
SFDR – 1GHz
Note: No spurs observed , for different span (10kHz, 100kHz, 1MHz, 10MHz, 100MHz, 1GHz, Full SPAN)
SST 14/11
SFDR – 10GHz
Note: No spurs observed , for different span (10kHz, 100kHz, 1MHz, 10MHz, 100MHz, 1GHz, Full SPAN)
SST 15/11
SFDR – 17GHz
Note: No spurs observed , for different span (10kHz, 100kHz, 1MHz, 10MHz, 100MHz, 1GHz, Full SPAN)
SST 16/11