Professional Documents
Culture Documents
Part Load Curves
Part Load Curves
Part Load Curves
2 2
CAP _ FT a b twb c twb d t odb e t odb f twb t odb
Qt ,available CAP _ FT Qt ,adj 2 2
CAP _ FT a b twb c twb d t odb e t odb f twb t odb
Qt,available Qoperating Available cooling capacity at specified evaporator and/or
PLR condenser conditions (MBH) 2 2
EIR _ FT a b twb c twb d todb e todb f twb todb
Qavailable twb , t odb / wt
Qt,adj Adjusted capacity at ARI conditions (Btu/h) (see Equation (11)
Poperating Prated EIR _ FPLR EIR _ FT CAP _ FT EIR _ FPLR a b PLR c PLR 2 d PLR 3
CAP_FT A multiplier to adjust Qt,adj
twb The entering coil wet-bulb temperature (°F)
tdb
Q The entering
Available coil dry-bulb
cooling capacitytemperature
at specified (°F)
evaporator and/or
t,available
twt condenser conditions (MBH)
The water supply temperature (°F)
Qt,adj
todb Adjusted
The capacity
outside-air at ARItemperature
dry-bulb conditions (Btu/h)
(°F) (see Equation
CAP_FT
Note: A multiplier
if an air-cooled unit employs to
anadjust Qt,adj condenser, todb is the effective dry-
evaporative
bulb temperature of the air leaving the evaporative cooling unit.
PLR Part load ratio based on available capacity (not rated capacity)
Table A multiplier
69 –Cooling Capacity
EIR-FPLR CurveonCoefficients
the EIR to account for the part load ratio
Air Cooled Direct Expansion Water Cooled Direct Expansion Chilled Water Coils
EIR-FT A multiplier on the EIR to account for the wet-bulb temperature
Air-Source Air-Source Water-Source Water-Source Other Chilled
Coefficient (PTAC) entering the coil
(Other DX)and the (Heat
outdoor dry-bulb
Pump) temperature
(Other DX) Fan-Coil Water
tawb The
1.1839345 entering coil wet-bulb
0.8740302 temperature (°F)
-0.2780377 0.9452633 0.5038866 2.5882585
tbwt -0.0081087
The water-0.0011416 0.0248307
supply temperature (°F) -0.0094199 -0.0869176 -0.2305879
c 0.0002110 0.0001711 -0.0000095 0.0002270 0.0016847 0.0038359
todb The outside-air dry-bulb temperature (°F)
d -0.0061435 -0.0029570 -0.0032731 0.0004805 0.0336304 0.1025812
Pe rated Rated
0.0000016 power draw at ARI0.0000070
0.0000102 conditions (kW)
-0.0000045 0.0002478 0.0005984
Pf operating -0.0000030
Power -0.0000592
draw -0.0000272 conditions
at specified operating -0.0000599
(kW) -0.0010297 -0.0028721
Note: These curves are the DOE-2.1E defaults, except for Water-Source (Other DX), which is taken from the “ECB Compliance
Note: if an air-cooled
Supplement, public reviewunit
draft employs antheevaporative
prepared by condenser,
SSPC 90.1 ECB t 1.2,
Panel, Version is the ef 1996.
March
Table 69 –Cooling Capacity Curve Coefficients
Air Cooled Direct Expansion Water Cooled Direct Expansion Chilled Water Coils
Air-Source Air-Source Water-Source Water-Source Other Chilled
Coefficient (PTAC) (Other DX) (Heat Pump) (Other DX) Fan-Coil Water
a 1.1839345 0.8740302 -0.2780377 0.9452633 0.5038866 2.5882585
b -0.0081087 -0.0011416 0.0248307 -0.0094199 -0.0869176 -0.2305879
c 0.0002110 0.0001711 -0.0000095 0.0002270 0.0016847 0.0038359
d -0.0061435 -0.0029570 -0.0032731 0.0004805 0.0336304 0.1025812
e 0.0000016 0.0000102 0.0000070 -0.0000045 0.0002478 0.0005984
f -0.0000030 -0.0000592 -0.0000272 -0.0000599 -0.0010297 -0.0028721
Note: These curves are the DOE-2.1E defaults, except for Water-Source (Other DX), which is taken from the “ECB Compliance
Supplement, public review draft prepared by the SSPC 90.1 ECB Panel, Version 1.2, March 1996.
Table G3.5.3 Performance Rating Method Water Chilling Packages—Minimum Efficiency Requirements
Subcategory or
Equipment Type Size Category Rating Condition Minimum Efficiency Test Procedure
Water-cooled, electrically <150 tons kW/ton 0.790 FL 0.676 IPLV.IP ARI 550/590
operated, positive 150 tons and 0.718 FL 0.629 IPLV.IP
displacement <300 tons
(rotary screw and scroll)
300 tons 0.639 FL 0.572 IPLV.IP
Water-cooled, electrically <150 tons kW/ton 0.703 FL 0.670 IPLV.IP ARI 550/590
operated, centrifugal 150 tons and 0.634 FL 0.596 IPLV.IP
<300 tons
300 tons 0.576 FL 0.549 IPLV.IP