Professional Documents
Culture Documents
Drain Cleaning Protocol: by Emily Gutowski On Dec 03, 2020 02:25 PM
Drain Cleaning Protocol: by Emily Gutowski On Dec 03, 2020 02:25 PM
This article is primarily based on HVAC School’s “Drain Cleaning – More To It Than We Think,”
hosted by Bryan Orr and featuring Corey Cruz and Mike Klokus.
How hard could it be to clean a drain? The slime should just wash away if you flush
the drain with water or blow some nitrogen in it, right? That’s one approach to take
to cleaning drains, but it’s not a very good one. Simple work (or straight-up
laziness) comes at the expense of callbacks and harsh Yelp reviews.
Here are some proper drain cleaning protocols that can prevent a lot of heartache
and time-consuming callbacks.
You’ll want to remove the panels on the air handler or case coil. That way, you can
access the drain pan and clean it. It’s easy for debris to build up in the drain pan.
Even though a quarter- or half-inch of grime doesn’t sound like a big deal, it’s going
to block fluids in the drain pan. We liken this obstructive action to a dam.
We recommend checking the status of the filter, evaporator coil, and condensate
safeties. These are especially critical for horizontal air handlers and during the
summer (when the unit will spend most of its time cooling).
You can make a small set of vinyl tubing tools to attach to some PVC and a shop
vac. Vinyl tubing allows you to see what you’re sucking up, so you can tell if you’re
making progress. You can also reach those channels with bottle brushes (or zip
ties and thermostat wire). When you use those materials, you may want to run
water while you clean those small channels. Water will force all the buildup to the
front while you work.
Grime builds up quickly in small channels and coils. Thoroughly cleaning them will
spare you trouble later.
Where will the water come out? Will the water flow into a drain pan or float switch
no matter what happens in the case of a backup or other issue? Is the float switch
and secondary pan firmly set in place so it won’t move or slide?
Ensuring that everything is anchored in place and able to handle the weight of the
water is crucial. The drain setup’s structural integrity will affect the drain’s function,
so it’s always a good idea to check that the drain can handle overflow and perform
its necessary job.
If a common drain backs up, several units are at risk of leakage. Also, you have to
make sure that you clean dedicated drains without messing up other people’s
drains. You have to be extra careful of backflow if you’re cleaning a single
dedicated drain within a communal drain system.
Drain size is also an important thing to note when dealing with communal vs.
dedicated drainage systems. It varies between dedicated and communal drain
systems. Dedicated drains are usually only about ¾” wide, while communal drains
can be around 2” wide.
We also strongly recommend considering where the condensate will come out
when you’re working with a communal system. If the drain leads out to a garden,
you may not want to dump chemicals in the drain pan!
We have already talked a little bit about wet/dry vacs. They are versatile and
portable tools, but they have their limitations. We have already said that they’re
difficult to fit into small spaces, but they are also on the weak side. Their suction
power is limited to 14.7 pounds of force per square inch by physics (and you
obviously get a lot less than that)
Compressed air or nitrogen is a bit stronger than a shop vac, but you have to be
more careful with it, especially in communal systems. You can cause leakages in
nearby drains if your compressed air messes up the piping. That is especially
problematic if the drain system runs through a wall. If you want to use compressed
air, it would be best to be mindful of your blowing power and the drain system’s
structural integrity. Cap vents properly and make sure fittings are glued before you
blow compressed air into a drain that leads to a common drain.
We believe that pressurized water is the best solution. It’s powerful, clean, and less
likely to cause problems in communal systems than compressed gases.
Unfortunately, you won’t always have a hose at the ready and may need to
consider other techniques when water is unavailable. You also have to be careful
not to let the water overflow into the return or make a mess in general.
You also have to be mindful of where the chemicals go. As I briefly mentioned
earlier, you will want to avoid using chemicals if the drain lets out in a place with
plants and personal property. Some sewer systems cannot handle certain
chemicals, so you should make sure the drain line either leads to a safe outdoor
location or that the sewer / septic can handle the chemicals you use.
It helps to understand what causes zoogloea. The slimy residue accumulates very
quickly and relies on environmental conditions for development. It’s especially
problematic in humid climates.
Introducing copper to a drain line will help solve a zoogloea problem. Copper in a
drain creates ions that serve an antibacterial purpose. Copper and some other
metals like silver are also useful against fungi and viruses.
For more information on preventing and treating zoogloea, check out this article on
bacterial zoogloea.
You can consider going outside and making sure the water runs consistently.
When the stream is constant and steady, you’ll know that there are no more
blockages. When there are uneven spurts of water, then you’ll know you have
another problem. It would also be wise to leave the unit running after you finish the
cleaning job. That way, you can see if it drains by its own power.
Whenever you have issues with intermittent drainage, popping sounds at the drain
or water blowing off the coil or out of the pan then check your static pressure and
air settings.
A double trap may also be the culprit of these problems. Double traps impede
drainage because air gets caught between the traps and prevents drainage.
On that note, don’t cap vents if you’re not actively cleaning a drain! Cleanouts get a
cap, vents (after the trap) do not.
Cleaning drains may seem like gross, mundane work, but learning to clean a drain
properly is an invaluable skill. Even though there is a lot to consider when cleaning
a drain properly, your customers will thank you for your careful work. By that, I
mean that you’ll deal with far fewer callbacks! There is no better reward for a job
well done.
If you want to learn more about drain standards and best practices for disposing of
condensate, you can read this article on Condensate Drain Codes and Best
Practices.