Professional Documents
Culture Documents
My CoreXY Build
My CoreXY Build
Home > Machines Organized by Style > CoreXY Machines > Topic
Search
Advanced
My CoreXY Build
Posted by Rectangled
Rectangled Registered: 5 years ago
My CoreXY Build
December 29, 2014 06:51PM
Posts: 11
Hello all,
I have just started to design my very first 3D printer and I just felt it was at a good point in time to share my CAD to get
people's feedback to make sure I am not doing anything horribly wrong or offensive. Plus it will help influence my design
for the better and will share all solidworks files once done.
I have creeped the forum and wiki quite a bit and defiantly like the coreXY style because it is basically like a CNC router
and could lend itself to that in the future, its also how the pros do it. They are not the cheapest but I do want to build
something that will last, print larger and I could use for work.
This is the basic XY frame with carriages and obviously is still in progress.
Custom brackets would be waterjet cut from 6mm steel or alu, then just drilled, tapped, or reamed areas that require higher
precision. Therefore, the bearing holes will be cut slightly smaller, reamed to the exact size then heated to fit the bearing.
Some specs:
Frame: 2020 x 2' from 80/20
Motors: Nemas 17
Controller: sanguinololu 1.3a
Belting: Gates GT2 2mm Pitch x 7mm
Everything else still in the air.
One thing that is still bothering me is whether to configure the belts on different level like gforce1 has shown (click) or the
conventional crossed way. I am guessing there is no real difference, except stacking two pivots on top of each other could
be a trickier and thicker setup.
https://reprap.org/forum/read.php?397,448930 1/17
4/21/2020 My CoreXY Build
Printer4.jpg
Printer2.jpg
https://reprap.org/forum/read.php?397,448930 2/17
4/21/2020 My CoreXY Build
Printer.jpg
Printer3.jpg
-B
jtoombs:
The the images are done in keyshot 5. The program is incredibly user friendly and creates impressive studio images within
minutes and minimal rendering knowledge. It doesn't have GI capabilities like vray, but after all it is designed for product
rendering. It also integrates well with just about any CAD package, (solidworks, catia, creo, sketchup, rhino, etc). Check it
out: here
Floyd:
Yeah I too like the idea of separating the framing structure from the linear motion. Having one piece act as the overall
structure, and another just service linear motion in my mind will generate lest binding or 'sticktion'; similar to the
requirement for crowns and axles on suspension forks to keep linear motion consistent.
I have updated my design and will post picture soon. Opted for crossed belt pattern actually.
Floyd Registered: 6 years ago
Re: My CoreXY Build
January 02, 2015 11:16PM
Posts: 770
Cant wait to see the new version. I too use Solidworks every day as a designer.
jtoombs Registered: 6 years ago
Re: My CoreXY Build
January 04, 2015 12:04AM
Posts: 102
Thanks a lot for the link Rectangle. I might just have try that out. I also can't wait to see what you have done with your
design. Keep us updated.
Rectangled Registered: 5 years ago
Re: My CoreXY Build
January 11, 2015 11:52PM
Posts: 11
Hey Guys,
Hey Floyd, always nice to meet another fellow designer. Currently, I am using (and learning at the same) time Creo at my
work which is proE. It is a pretty neat piece of software especially the Style feature. If you are solidworks native you should
defiantly check it out.
https://reprap.org/forum/read.php?397,448930 4/17
4/21/2020 My CoreXY Build
Printer_RevB.jpg
Printer_RevB_2.jpg
https://reprap.org/forum/read.php?397,448930 5/17
4/21/2020 My CoreXY Build
Untitled-1-01.jpg
One of the issues I had with my previous design was everything was too too overbuilt and clunky. I had 12mm and 10mm
linear rods, 4 giant pillow block on each carriage and thick sheet metal structure that I feel would have made a really heavy
printer. And we all know too heavy is too much inertia, vibration and satisfactory prints. In my mind the demand for
lightness and accuracy of parts outweighed shear brute stiffness to create a locked down printer.
Aligning belt idler directly on top of each other required too much complicated bearing work, especially since I want to use
little ball bearings everywhere possible.
Next:
-How to clamp the timing belts nicely?
-How to mount the hot end (and work in the bowden extruder), there is two cuts on the X carriage that is the beginning of
this.
-Z axis, but I am not too worried about this just yet.
I do a lot of CAD waffling back and forth between ideas, which is poor practice and why this is taking so darn long with
nothing physical to show for it. I know it is a lot of theorizing and 'what ifs' with no tangible proof, but I am that guy who
has to CAD every last detail before the execute. Hopefully, the next post will be the start of construction!
Floyd Registered: 6 years ago
Re: My CoreXY Build
January 13, 2015 08:33AM
Posts: 770
Quote
Rectangled
...I am that guy who has to CAD every last detail before the execute.
I have had an Idea to make a solution for the advantage of an Ultimaker mechanic and a Core x/y advantage for a 2/1 gear
https://reprap.org/forum/read.php?397,448930 6/17
4/21/2020 My CoreXY Build
Ulti-x-y-skizze.png
I can not design it (no deep cad expiriance and only sketchup, freecad or openscad beginer ..))
On the aluminum profiles each 2 HIWIN guides, the guide rollers on y and again deflected over solid rollers on the outer
race cars of the X guides. Thus, the tensile forces on the outer trolley, similar to the Ultimaker then push the middle crossed
HIWIN guides. By taking advantage of the Core x / y kinematics but that would have to be the maas of things. The
disadvantage of the longer belt could be compensated with wider. Would that even an idea for you?
Angelo
Enrico
[www.dapa3dservice.it] [www.studiodapa.it]
repstrap dApA, Ramps 1.4, MarlinKimbra / scanner 3D Cubify Sense / Formlabs Form 2
Attachments:
open | download - bozza core xy complanare.jpg (165.3 KB)
open | download - bozza core xy.jpg (162.2 KB)
Rectangled Registered: 5 years ago
Re: My CoreXY Build
March 14, 2015 02:30PM
Posts: 11
Finalized CAD
https://reprap.org/forum/read.php?397,448930 7/17
4/21/2020 My CoreXY Build
RevD_2.jpg
RevD_1.jpg
(grayscale)
https://reprap.org/forum/read.php?397,448930 8/17
4/21/2020 My CoreXY Build
RevD_3_Clay.jpg
Top_View.jpg
https://reprap.org/forum/read.php?397,448930 9/17
4/21/2020 My CoreXY Build
Carriage_x.jpg
Carriage_x-2.jpg
https://reprap.org/forum/read.php?397,448930 10/17
4/21/2020 My CoreXY Build
Carriage_x-3.jpg
Idler_Corner.jpg
It has been a while since my last post, but this has been kinda my back-burner project. This is a quick post, and I will try to
address the comments above in a later post (regarding your belting suggestions).
Floyd Registered: 6 years ago
Re: My CoreXY Build
March 14, 2015 09:46PM
Posts: 770
Looks spot on!
Great execution.
As a daily SW user I can say bravo.
vertcnc Registered: 5 years ago
Re: My CoreXY Build
March 30, 2015 11:18AM
Posts: 2
Hi Rectangled,
Your printer looks awesome. Do you plan on releasing the drawings or part files.
Thanks
ChrisT88 Registered: 5 years ago
Posts: 36
https://reprap.org/forum/read.php?397,448930 11/17
4/21/2020 My CoreXY Build
Re: My CoreXY Build
March 31, 2015 07:17PM
Elegant design. I love the size, plush end stops, linear rails ect. Would like to see a small kit of the harder to find metal
pieces you custom made!
s1475478 Registered: 4 years ago
Re: My CoreXY Build
May 22, 2015 01:13AM
Posts: 1
Dear All
can any one give me a direction where I can find CoreXY Marlin
i had built a CoreXY, but just couldn't find any firmware to try out
dougal1957 Registered: 5 years ago
Re: My CoreXY Build
May 22, 2015 02:08AM
Posts: 1,159
Quote
s1475478
Dear All
can any one give me a direction where I can find CoreXY Marlin
i had built a CoreXY, but just couldn't find any firmware to try out
Enrico
[www.dapa3dservice.it] [www.studiodapa.it]
repstrap dApA, Ramps 1.4, MarlinKimbra / scanner 3D Cubify Sense / Formlabs Form 2
Rectangled Registered: 5 years ago
Re: My CoreXY Build
May 31, 2015 02:59PM
Posts: 11
https://reprap.org/forum/read.php?397,448930 12/17
4/21/2020 My CoreXY Build
Build2.jpg
Build22.jpg
https://reprap.org/forum/read.php?397,448930 13/17
4/21/2020 My CoreXY Build
Build23.jpg
Whole_shot.jpg
I kind of expected that once I got into the assembly I would learn a lot and already there are things that I need to go back
and change in CAD. Particularly, the order in which things came together was not heavily considered and I had to do a lot
of cutting, filing and swearing to get things to fit.
Belt motion feels good. Having abec-7 bearings on every axis defiantly contributes to the buttery feel. I will try and fire it
up sometime to get it dancing.
I plan to fully build this coreXY as intended then make changes afterward. Particularly the Acrylic brackets need to be a
better material as Acrylic is a terrible plastic.
I can share CAD files with the community if people would like. Though keep in mind there are these assembly errors that I
would like to fix first. I can do another quick rev. on the CAD and share it then? Or I can share what I have right now,
whatever you guys prefer? Also, any suggestions for the best and safest way to share large size CAD files, dropbox?
https://reprap.org/forum/read.php?397,448930 14/17
4/21/2020 My CoreXY Build
Regards
Makerparts.ca
Your Canadian source for V-Slot Extrusion, CNC and 3D Printing Parts and Accessories.
we are proud to be an official Openbuilds distributor.
manugogli Registered: 4 years ago
Re: My CoreXY Build
May 26, 2016 08:39AM
Posts: 11
yes! Please share the files! i love the design.
cozmicray Registered: 7 years ago
Re: My CoreXY Build
May 26, 2016 01:58PM
Posts: 1,046
Excellent work!!
Why do guide rails go all the way to end? (trolley can't go there)
Thank you
Simon.
[www.precisionpiezo.co.uk] Accurate, repeatable, versatile z-probe plus piezo discs, endstop cables, pt100, 50w heaters. PT1000 cartridge sensors plug straight into duet boards and others.
Published:Inventions
Rectangled Registered: 5 years ago
https://reprap.org/forum/read.php?397,448930 15/17
4/21/2020 My CoreXY Build
Re: My CoreXY Build Posts: 11
July 23, 2016 07:13PM
Hello,
This is long overdue, but here are the CAD files for this project
I am really sorry about the delay. I noticed that a lot of people where requesting the files and I have basically been totally
absent on the forum for about a year now! Now that school is finished I can resume this project and after thinking more
about it, I might move to a Kossel design.
-It is NOT a complete and finalized printer! So please don't blindly build this design as it is NOT proven. I would hate for
someone to spend money to try and build this and become frustrated that is doesn't run correctly.
-I am sharing the CAD because maybe someone can build off of it? Or use elements of its design. And so that the work
done can have some further purpose.
I am happy to answer questions the best I can about the CAD, and let me know if there is troubles with the files or opening
them.
-b
jk25 Registered: 7 years ago
Re: My CoreXY Build
August 01, 2016 04:40PM
Posts: 156
I like that you even support the upper ends of the lead screws by using some ball bearings.
Nice build!
wbwing Registered: 3 years ago
Re: My CoreXY Build
August 20, 2016 03:26AM
Posts: 17
So I'm digging into this design and seeing if I can build it into something useful. Just beautiful work Rectangled. From the
comments I'm assuming the OP is no longer working on this project? I'm still really new to 3d printer design, so if you are
still open to some questions, it would be a great help to me.
I measured the bed to be very large... 600mmx600mm I think. Much larger than my min target. One thing I haven't been
able to figure out is how to determine how much of the bed is actually usable. I don't fully understand how far the x and y
carriage can extend. I want to restrict it to no larger than 500mmx500mm (the convenient size for bed heaters and
Printbite). I'm not sure how to exactly determine what range the current design is actually limited too.
As far as I can tell, no space has been allotted for electronics or other printer elements (such as where to mount the spool.
I'm thinking either extending the extrusions to one side, or making the vertical extrusions taller to give space below the bed
for electronics. Is there a preferred method. I am thinking to the side makes for easier access, while underneath is better for
keeping the overall footprint down (the design is already quite large). Any thoughts?
Hi. I can answer questions as best I can if you have any. But yes I am currently not active on this project.
-Yes I believe the bed is around 600x600. Which is pretty big.
-I also had not considered electronics or spooling. But I guess I had figured these features where not mechanically integral
to performance and can be added later.
https://reprap.org/forum/read.php?397,448930 16/17
4/21/2020 My CoreXY Build
The design is quite large, but I don't see any reason why it cannot be scaled down? The concept around how the corners are
executed is probably of the most interest. I bet you could adapt the corners to work with shorted straight sections?
Regards,
-B
https://reprap.org/forum/read.php?397,448930 17/17