Professional Documents
Culture Documents
LC-70UD1U 2k/4k Service Training: Ver. 5ff
LC-70UD1U 2k/4k Service Training: Ver. 5ff
Ver. 5ff
Course Objectives:
2
1
What is 4K
The new 4K technology is now entering living rooms around the world.
• It is double the resolution of 2K technology, or 1920x1080 =
3840x2160.
• All signal is first up scaled to 1920x1080, enhanced, and then scaled to
3840x2160.
• Native signal at 3840x2160 is not up scaled or enhance.
3
1a
Rear Cabinet Removal
2
Rear Cabinet Removal
remove cord.
3
Rear Cabinet Removal
4
Sub-Woofer Removal
5
PWB Layout
Main Unit
DRC/FRC
T-Con
Power Unit
6
Connection Layout
SERVICE
7
Power Unit Operation
8
Main Unit Operation
The main PWB is responsible for the following
operations:
9
Main Unit Operation continued
The Monitor/Sub Micon section is
responsible for power supply and power
detection.
U+5V
D+5V
D+3.3V
D+1.5V
D+1.2V
BU+3.3V
Backlight error detection
12V panel power detection
10
LED Drive Operation
The LED drive unit is
responsible for providing
LED drive voltage for the
edge lit display.
11
DRC/FRC/TCON Operation
DRC: Dynamic Range Compression
Receives LVDS from Main PWB
which was converted to 2k when
content is at a lower resolution then
DRC/FRC
1080.
DRC enhances image before
converting to 4K.
4 K resolution = 3,840 x 2,160,
which is double from 1920x1080.
DRC adds 3 pixels for every single
pixel with 1080 I/P video sources.
FRC converts the 60hz LVDS to
120Hz.
4 LCD drive signals lines directly
T-Con output the LCD controller at 210MHz
PPDS format, which drives the 10bit
LCD panel.
12
Main Unit Removal
SB
PD
SP Remove 8 cables
13
Main PWB Installation
Entering the
adjustment process
mode
1) Press and continue
to hold the VOL &
INPUT buttons while
70UD1U plugging in AC
power.
14
Main PWB Installation
15
Main PWB Installation
16
Main PWB Installation
17
Main PWB Installation
18
Main PWB Installation
7) Press “Enter” on
remote control. You
will see “UD1U OK” to
confirm your setting.
UD1U OK
19
Main PWB Installation
20
Main PWB Installation
9) Press “Enter” on
remote control. You will
UD1U OK
see “70 OK OK” to
confirm your setting.
70 OK OK
21
Main PWB Installation
22
How to Perform Lamp Error Reset
23
How to Perform Lamp Error Reset
24
How to Perform Lamp Error Reset
25
How to Perform Industry INIT
26
How to Perform Industry INIT
27
How to Perform Industry INIT
28
Exiting Service Menu
31
Power Unit Removal
LA
PD
Disconnect 4 cables.
AC INLET
32
DRC/FRC and TCON Removal
33
DRC/FRC Unit Removal
LW
DRC/FRC
Disconnect 4 cables.
SC8501 SC8502
T-Con
34
TCON Unit Removal
DRC/FRC
Disconnect 7 cables
VA VB
PT T-Con
35
LED Drive PWB Removal
Disconnect 3 cables.
L1
LA
36
Performing Software Upgrade
Figure 1
Figure
Figure
Figure 1 11 1. Unplug the AC cord
2. Insert the USB Memory Device
with the Main Software Upgrade
into the side terminal
3. Plug in the AC cord while holding
down power button on the unit
for ~5 seconds
4. After the unit powers up a screen
will be displayed showing the
Figure
Figure
Figure 2 2
2 upgrade progress as in Figure 1
5. Once the upgrade is complete the
screen will display an “UPGRADE
SUCCESS” message. as in Figure 2
37
Upgrade Failure
38
Troubleshooting
Flashing Power / Timer LED
In most of our past models a
faulty, loose, or disconnected
LVDS cable can lead to errors,
such as “Power Icon” 2 slow and
5 fast, or 2 “Power”, 5 “OPC”, etc.
However, LC70UD1U will behave
in the following manner.
39
Troubleshooting
Flashing Power / Timer LED
39a
Troubleshooting
Error / Standby Causes
40
Troubleshooting
Monitor Error Causes
41
Troubleshooting
Normal and Error Standby Causes
42
Troubleshooting
Normal and Error Standby Causes
Normal Standby Cause
43
Troubleshooting LED Backlight
Failure
If the Power and Timer
LED’s indicate lamp
errors, try the following
troubleshooting
methods.
Force the set on using
Ch Vol while
plugging in ac power
L1
cord.
If the set turns on, look
L2 for backlight
illumination.
If set does not turn on,
Remove L1 and L2
independently, and
Note: The set will run for ~ 10 seconds force-on. If unit turns on
With L1 or L2 disconnected. Then the set will the LED backlight is
shut down. This will prove a bad LED strip most likely at fault.
inside the LCD panel.
44
Troubleshooting LCD Panel
45
Troubleshooting LCD Panel
46
Troubleshooting LCD Panel
TV TEST PATTERN
The TV test pattern is generated on
the Main PWB and applies the test
pattern to the LCD Controller.
47
This concludes our AQUOS Training
Any Questions?